1 .. SPDX-License-Identifier: GPL-2.0 1 .. SPDX-License-Identifier: GPL-2.0
2 .. include:: <isonum.txt> 2 .. include:: <isonum.txt>
3 3
4 ============================================== 4 ===============================================
5 ``intel_pstate`` CPU Performance Scaling Drive 5 ``intel_pstate`` CPU Performance Scaling Driver
6 ============================================== 6 ===============================================
7 7
8 :Copyright: |copy| 2017 Intel Corporation 8 :Copyright: |copy| 2017 Intel Corporation
9 9
10 :Author: Rafael J. Wysocki <rafael.j.wysocki@in 10 :Author: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
11 11
12 12
13 General Information 13 General Information
14 =================== 14 ===================
15 15
16 ``intel_pstate`` is a part of the 16 ``intel_pstate`` is a part of the
17 :doc:`CPU performance scaling subsystem <cpufr 17 :doc:`CPU performance scaling subsystem <cpufreq>` in the Linux kernel
18 (``CPUFreq``). It is a scaling driver for the 18 (``CPUFreq``). It is a scaling driver for the Sandy Bridge and later
19 generations of Intel processors. Note, howeve 19 generations of Intel processors. Note, however, that some of those processors
20 may not be supported. [To understand ``intel_ 20 may not be supported. [To understand ``intel_pstate`` it is necessary to know
21 how ``CPUFreq`` works in general, so this is t 21 how ``CPUFreq`` works in general, so this is the time to read
22 Documentation/admin-guide/pm/cpufreq.rst if yo 22 Documentation/admin-guide/pm/cpufreq.rst if you have not done that yet.]
23 23
24 For the processors supported by ``intel_pstate 24 For the processors supported by ``intel_pstate``, the P-state concept is broader
25 than just an operating frequency or an operati 25 than just an operating frequency or an operating performance point (see the
26 LinuxCon Europe 2015 presentation by Kristen A 26 LinuxCon Europe 2015 presentation by Kristen Accardi [1]_ for more
27 information about that). For this reason, the 27 information about that). For this reason, the representation of P-states used
28 by ``intel_pstate`` internally follows the har 28 by ``intel_pstate`` internally follows the hardware specification (for details
29 refer to Intel Software Developer’s Manual [ 29 refer to Intel Software Developer’s Manual [2]_). However, the ``CPUFreq`` core
30 uses frequencies for identifying operating per 30 uses frequencies for identifying operating performance points of CPUs and
31 frequencies are involved in the user space int 31 frequencies are involved in the user space interface exposed by it, so
32 ``intel_pstate`` maps its internal representat 32 ``intel_pstate`` maps its internal representation of P-states to frequencies too
33 (fortunately, that mapping is unambiguous). A 33 (fortunately, that mapping is unambiguous). At the same time, it would not be
34 practical for ``intel_pstate`` to supply the ` 34 practical for ``intel_pstate`` to supply the ``CPUFreq`` core with a table of
35 available frequencies due to the possible size 35 available frequencies due to the possible size of it, so the driver does not do
36 that. Some functionality of the core is limit 36 that. Some functionality of the core is limited by that.
37 37
38 Since the hardware P-state selection interface 38 Since the hardware P-state selection interface used by ``intel_pstate`` is
39 available at the logical CPU level, the driver 39 available at the logical CPU level, the driver always works with individual
40 CPUs. Consequently, if ``intel_pstate`` is in 40 CPUs. Consequently, if ``intel_pstate`` is in use, every ``CPUFreq`` policy
41 object corresponds to one logical CPU and ``CP 41 object corresponds to one logical CPU and ``CPUFreq`` policies are effectively
42 equivalent to CPUs. In particular, this means 42 equivalent to CPUs. In particular, this means that they become "inactive" every
43 time the corresponding CPU is taken offline an 43 time the corresponding CPU is taken offline and need to be re-initialized when
44 it goes back online. 44 it goes back online.
45 45
46 ``intel_pstate`` is not modular, so it cannot 46 ``intel_pstate`` is not modular, so it cannot be unloaded, which means that the
47 only way to pass early-configuration-time para 47 only way to pass early-configuration-time parameters to it is via the kernel
48 command line. However, its configuration can 48 command line. However, its configuration can be adjusted via ``sysfs`` to a
49 great extent. In some configurations it even 49 great extent. In some configurations it even is possible to unregister it via
50 ``sysfs`` which allows another ``CPUFreq`` sca 50 ``sysfs`` which allows another ``CPUFreq`` scaling driver to be loaded and
51 registered (see `below <status_attr_>`_). 51 registered (see `below <status_attr_>`_).
52 52
53 53
54 Operation Modes 54 Operation Modes
55 =============== 55 ===============
56 56
57 ``intel_pstate`` can operate in two different 57 ``intel_pstate`` can operate in two different modes, active or passive. In the
58 active mode, it uses its own internal performa 58 active mode, it uses its own internal performance scaling governor algorithm or
59 allows the hardware to do performance scaling 59 allows the hardware to do performance scaling by itself, while in the passive
60 mode it responds to requests made by a generic 60 mode it responds to requests made by a generic ``CPUFreq`` governor implementing
61 a certain performance scaling algorithm. Whic 61 a certain performance scaling algorithm. Which of them will be in effect
62 depends on what kernel command line options ar 62 depends on what kernel command line options are used and on the capabilities of
63 the processor. 63 the processor.
64 64
65 Active Mode 65 Active Mode
66 ----------- 66 -----------
67 67
68 This is the default operation mode of ``intel_ 68 This is the default operation mode of ``intel_pstate`` for processors with
69 hardware-managed P-states (HWP) support. If i 69 hardware-managed P-states (HWP) support. If it works in this mode, the
70 ``scaling_driver`` policy attribute in ``sysfs 70 ``scaling_driver`` policy attribute in ``sysfs`` for all ``CPUFreq`` policies
71 contains the string "intel_pstate". 71 contains the string "intel_pstate".
72 72
73 In this mode the driver bypasses the scaling g 73 In this mode the driver bypasses the scaling governors layer of ``CPUFreq`` and
74 provides its own scaling algorithms for P-stat 74 provides its own scaling algorithms for P-state selection. Those algorithms
75 can be applied to ``CPUFreq`` policies in the 75 can be applied to ``CPUFreq`` policies in the same way as generic scaling
76 governors (that is, through the ``scaling_gove 76 governors (that is, through the ``scaling_governor`` policy attribute in
77 ``sysfs``). [Note that different P-state sele 77 ``sysfs``). [Note that different P-state selection algorithms may be chosen for
78 different policies, but that is not recommende 78 different policies, but that is not recommended.]
79 79
80 They are not generic scaling governors, but th 80 They are not generic scaling governors, but their names are the same as the
81 names of some of those governors. Moreover, c 81 names of some of those governors. Moreover, confusingly enough, they generally
82 do not work in the same way as the generic gov 82 do not work in the same way as the generic governors they share the names with.
83 For example, the ``powersave`` P-state selecti 83 For example, the ``powersave`` P-state selection algorithm provided by
84 ``intel_pstate`` is not a counterpart of the g 84 ``intel_pstate`` is not a counterpart of the generic ``powersave`` governor
85 (roughly, it corresponds to the ``schedutil`` 85 (roughly, it corresponds to the ``schedutil`` and ``ondemand`` governors).
86 86
87 There are two P-state selection algorithms pro 87 There are two P-state selection algorithms provided by ``intel_pstate`` in the
88 active mode: ``powersave`` and ``performance`` 88 active mode: ``powersave`` and ``performance``. The way they both operate
89 depends on whether or not the hardware-managed 89 depends on whether or not the hardware-managed P-states (HWP) feature has been
90 enabled in the processor and possibly on the p 90 enabled in the processor and possibly on the processor model.
91 91
92 Which of the P-state selection algorithms is u 92 Which of the P-state selection algorithms is used by default depends on the
93 :c:macro:`CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMA 93 :c:macro:`CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE` kernel configuration option.
94 Namely, if that option is set, the ``performan 94 Namely, if that option is set, the ``performance`` algorithm will be used by
95 default, and the other one will be used by def 95 default, and the other one will be used by default if it is not set.
96 96
97 Active Mode With HWP 97 Active Mode With HWP
98 ~~~~~~~~~~~~~~~~~~~~ 98 ~~~~~~~~~~~~~~~~~~~~
99 99
100 If the processor supports the HWP feature, it 100 If the processor supports the HWP feature, it will be enabled during the
101 processor initialization and cannot be disable 101 processor initialization and cannot be disabled after that. It is possible
102 to avoid enabling it by passing the ``intel_ps 102 to avoid enabling it by passing the ``intel_pstate=no_hwp`` argument to the
103 kernel in the command line. 103 kernel in the command line.
104 104
105 If the HWP feature has been enabled, ``intel_p 105 If the HWP feature has been enabled, ``intel_pstate`` relies on the processor to
106 select P-states by itself, but still it can gi 106 select P-states by itself, but still it can give hints to the processor's
107 internal P-state selection logic. What those 107 internal P-state selection logic. What those hints are depends on which P-state
108 selection algorithm has been applied to the gi 108 selection algorithm has been applied to the given policy (or to the CPU it
109 corresponds to). 109 corresponds to).
110 110
111 Even though the P-state selection is carried o 111 Even though the P-state selection is carried out by the processor automatically,
112 ``intel_pstate`` registers utilization update 112 ``intel_pstate`` registers utilization update callbacks with the CPU scheduler
113 in this mode. However, they are not used for 113 in this mode. However, they are not used for running a P-state selection
114 algorithm, but for periodic updates of the cur 114 algorithm, but for periodic updates of the current CPU frequency information to
115 be made available from the ``scaling_cur_freq` 115 be made available from the ``scaling_cur_freq`` policy attribute in ``sysfs``.
116 116
117 HWP + ``performance`` 117 HWP + ``performance``
118 ..................... 118 .....................
119 119
120 In this configuration ``intel_pstate`` will wr 120 In this configuration ``intel_pstate`` will write 0 to the processor's
121 Energy-Performance Preference (EPP) knob (if s 121 Energy-Performance Preference (EPP) knob (if supported) or its
122 Energy-Performance Bias (EPB) knob (otherwise) 122 Energy-Performance Bias (EPB) knob (otherwise), which means that the processor's
123 internal P-state selection logic is expected t 123 internal P-state selection logic is expected to focus entirely on performance.
124 124
125 This will override the EPP/EPB setting coming 125 This will override the EPP/EPB setting coming from the ``sysfs`` interface
126 (see `Energy vs Performance Hints`_ below). M 126 (see `Energy vs Performance Hints`_ below). Moreover, any attempts to change
127 the EPP/EPB to a value different from 0 ("perf 127 the EPP/EPB to a value different from 0 ("performance") via ``sysfs`` in this
128 configuration will be rejected. 128 configuration will be rejected.
129 129
130 Also, in this configuration the range of P-sta 130 Also, in this configuration the range of P-states available to the processor's
131 internal P-state selection logic is always res 131 internal P-state selection logic is always restricted to the upper boundary
132 (that is, the maximum P-state that the driver 132 (that is, the maximum P-state that the driver is allowed to use).
133 133
134 HWP + ``powersave`` 134 HWP + ``powersave``
135 ................... 135 ...................
136 136
137 In this configuration ``intel_pstate`` will se 137 In this configuration ``intel_pstate`` will set the processor's
138 Energy-Performance Preference (EPP) knob (if s 138 Energy-Performance Preference (EPP) knob (if supported) or its
139 Energy-Performance Bias (EPB) knob (otherwise) 139 Energy-Performance Bias (EPB) knob (otherwise) to whatever value it was
140 previously set to via ``sysfs`` (or whatever d 140 previously set to via ``sysfs`` (or whatever default value it was
141 set to by the platform firmware). This usuall 141 set to by the platform firmware). This usually causes the processor's
142 internal P-state selection logic to be less pe 142 internal P-state selection logic to be less performance-focused.
143 143
144 Active Mode Without HWP 144 Active Mode Without HWP
145 ~~~~~~~~~~~~~~~~~~~~~~~ 145 ~~~~~~~~~~~~~~~~~~~~~~~
146 146
147 This operation mode is optional for processors 147 This operation mode is optional for processors that do not support the HWP
148 feature or when the ``intel_pstate=no_hwp`` ar 148 feature or when the ``intel_pstate=no_hwp`` argument is passed to the kernel in
149 the command line. The active mode is used in 149 the command line. The active mode is used in those cases if the
150 ``intel_pstate=active`` argument is passed to 150 ``intel_pstate=active`` argument is passed to the kernel in the command line.
151 In this mode ``intel_pstate`` may refuse to wo 151 In this mode ``intel_pstate`` may refuse to work with processors that are not
152 recognized by it. [Note that ``intel_pstate`` 152 recognized by it. [Note that ``intel_pstate`` will never refuse to work with
153 any processor with the HWP feature enabled.] 153 any processor with the HWP feature enabled.]
154 154
155 In this mode ``intel_pstate`` registers utiliz 155 In this mode ``intel_pstate`` registers utilization update callbacks with the
156 CPU scheduler in order to run a P-state select 156 CPU scheduler in order to run a P-state selection algorithm, either
157 ``powersave`` or ``performance``, depending on 157 ``powersave`` or ``performance``, depending on the ``scaling_governor`` policy
158 setting in ``sysfs``. The current CPU frequen 158 setting in ``sysfs``. The current CPU frequency information to be made
159 available from the ``scaling_cur_freq`` policy 159 available from the ``scaling_cur_freq`` policy attribute in ``sysfs`` is
160 periodically updated by those utilization upda 160 periodically updated by those utilization update callbacks too.
161 161
162 ``performance`` 162 ``performance``
163 ............... 163 ...............
164 164
165 Without HWP, this P-state selection algorithm 165 Without HWP, this P-state selection algorithm is always the same regardless of
166 the processor model and platform configuration 166 the processor model and platform configuration.
167 167
168 It selects the maximum P-state it is allowed t 168 It selects the maximum P-state it is allowed to use, subject to limits set via
169 ``sysfs``, every time the driver configuration 169 ``sysfs``, every time the driver configuration for the given CPU is updated
170 (e.g. via ``sysfs``). 170 (e.g. via ``sysfs``).
171 171
172 This is the default P-state selection algorith 172 This is the default P-state selection algorithm if the
173 :c:macro:`CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMA 173 :c:macro:`CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE` kernel configuration option
174 is set. 174 is set.
175 175
176 ``powersave`` 176 ``powersave``
177 ............. 177 .............
178 178
179 Without HWP, this P-state selection algorithm 179 Without HWP, this P-state selection algorithm is similar to the algorithm
180 implemented by the generic ``schedutil`` scali 180 implemented by the generic ``schedutil`` scaling governor except that the
181 utilization metric used by it is based on numb 181 utilization metric used by it is based on numbers coming from feedback
182 registers of the CPU. It generally selects P- 182 registers of the CPU. It generally selects P-states proportional to the
183 current CPU utilization. 183 current CPU utilization.
184 184
185 This algorithm is run by the driver's utilizat 185 This algorithm is run by the driver's utilization update callback for the
186 given CPU when it is invoked by the CPU schedu 186 given CPU when it is invoked by the CPU scheduler, but not more often than
187 every 10 ms. Like in the ``performance`` case 187 every 10 ms. Like in the ``performance`` case, the hardware configuration
188 is not touched if the new P-state turns out to 188 is not touched if the new P-state turns out to be the same as the current
189 one. 189 one.
190 190
191 This is the default P-state selection algorith 191 This is the default P-state selection algorithm if the
192 :c:macro:`CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMA 192 :c:macro:`CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE` kernel configuration option
193 is not set. 193 is not set.
194 194
195 Passive Mode 195 Passive Mode
196 ------------ 196 ------------
197 197
198 This is the default operation mode of ``intel_ 198 This is the default operation mode of ``intel_pstate`` for processors without
199 hardware-managed P-states (HWP) support. It i 199 hardware-managed P-states (HWP) support. It is always used if the
200 ``intel_pstate=passive`` argument is passed to 200 ``intel_pstate=passive`` argument is passed to the kernel in the command line
201 regardless of whether or not the given process 201 regardless of whether or not the given processor supports HWP. [Note that the
202 ``intel_pstate=no_hwp`` setting causes the dri 202 ``intel_pstate=no_hwp`` setting causes the driver to start in the passive mode
203 if it is not combined with ``intel_pstate=acti 203 if it is not combined with ``intel_pstate=active``.] Like in the active mode
204 without HWP support, in this mode ``intel_psta 204 without HWP support, in this mode ``intel_pstate`` may refuse to work with
205 processors that are not recognized by it if HW 205 processors that are not recognized by it if HWP is prevented from being enabled
206 through the kernel command line. 206 through the kernel command line.
207 207
208 If the driver works in this mode, the ``scalin 208 If the driver works in this mode, the ``scaling_driver`` policy attribute in
209 ``sysfs`` for all ``CPUFreq`` policies contain 209 ``sysfs`` for all ``CPUFreq`` policies contains the string "intel_cpufreq".
210 Then, the driver behaves like a regular ``CPUF 210 Then, the driver behaves like a regular ``CPUFreq`` scaling driver. That is,
211 it is invoked by generic scaling governors whe 211 it is invoked by generic scaling governors when necessary to talk to the
212 hardware in order to change the P-state of a C 212 hardware in order to change the P-state of a CPU (in particular, the
213 ``schedutil`` governor can invoke it directly 213 ``schedutil`` governor can invoke it directly from scheduler context).
214 214
215 While in this mode, ``intel_pstate`` can be us 215 While in this mode, ``intel_pstate`` can be used with all of the (generic)
216 scaling governors listed by the ``scaling_avai 216 scaling governors listed by the ``scaling_available_governors`` policy attribute
217 in ``sysfs`` (and the P-state selection algori 217 in ``sysfs`` (and the P-state selection algorithms described above are not
218 used). Then, it is responsible for the config 218 used). Then, it is responsible for the configuration of policy objects
219 corresponding to CPUs and provides the ``CPUFr 219 corresponding to CPUs and provides the ``CPUFreq`` core (and the scaling
220 governors attached to the policy objects) with 220 governors attached to the policy objects) with accurate information on the
221 maximum and minimum operating frequencies supp 221 maximum and minimum operating frequencies supported by the hardware (including
222 the so-called "turbo" frequency ranges). In o 222 the so-called "turbo" frequency ranges). In other words, in the passive mode
223 the entire range of available P-states is expo 223 the entire range of available P-states is exposed by ``intel_pstate`` to the
224 ``CPUFreq`` core. However, in this mode the d 224 ``CPUFreq`` core. However, in this mode the driver does not register
225 utilization update callbacks with the CPU sche 225 utilization update callbacks with the CPU scheduler and the ``scaling_cur_freq``
226 information comes from the ``CPUFreq`` core (a 226 information comes from the ``CPUFreq`` core (and is the last frequency selected
227 by the current scaling governor for the given 227 by the current scaling governor for the given policy).
228 228
229 229
230 .. _turbo: 230 .. _turbo:
231 231
232 Turbo P-states Support 232 Turbo P-states Support
233 ====================== 233 ======================
234 234
235 In the majority of cases, the entire range of 235 In the majority of cases, the entire range of P-states available to
236 ``intel_pstate`` can be divided into two sub-r 236 ``intel_pstate`` can be divided into two sub-ranges that correspond to
237 different types of processor behavior, above a 237 different types of processor behavior, above and below a boundary that
238 will be referred to as the "turbo threshold" i 238 will be referred to as the "turbo threshold" in what follows.
239 239
240 The P-states above the turbo threshold are ref 240 The P-states above the turbo threshold are referred to as "turbo P-states" and
241 the whole sub-range of P-states they belong to 241 the whole sub-range of P-states they belong to is referred to as the "turbo
242 range". These names are related to the Turbo 242 range". These names are related to the Turbo Boost technology allowing a
243 multicore processor to opportunistically incre 243 multicore processor to opportunistically increase the P-state of one or more
244 cores if there is enough power to do that and 244 cores if there is enough power to do that and if that is not going to cause the
245 thermal envelope of the processor package to b 245 thermal envelope of the processor package to be exceeded.
246 246
247 Specifically, if software sets the P-state of 247 Specifically, if software sets the P-state of a CPU core within the turbo range
248 (that is, above the turbo threshold), the proc 248 (that is, above the turbo threshold), the processor is permitted to take over
249 performance scaling control for that core and 249 performance scaling control for that core and put it into turbo P-states of its
250 choice going forward. However, that permissio 250 choice going forward. However, that permission is interpreted differently by
251 different processor generations. Namely, the 251 different processor generations. Namely, the Sandy Bridge generation of
252 processors will never use any P-states above t 252 processors will never use any P-states above the last one set by software for
253 the given core, even if it is within the turbo 253 the given core, even if it is within the turbo range, whereas all of the later
254 processor generations will take it as a licens 254 processor generations will take it as a license to use any P-states from the
255 turbo range, even above the one set by softwar 255 turbo range, even above the one set by software. In other words, on those
256 processors setting any P-state from the turbo 256 processors setting any P-state from the turbo range will enable the processor
257 to put the given core into all turbo P-states 257 to put the given core into all turbo P-states up to and including the maximum
258 supported one as it sees fit. 258 supported one as it sees fit.
259 259
260 One important property of turbo P-states is th 260 One important property of turbo P-states is that they are not sustainable. More
261 precisely, there is no guarantee that any CPUs 261 precisely, there is no guarantee that any CPUs will be able to stay in any of
262 those states indefinitely, because the power d 262 those states indefinitely, because the power distribution within the processor
263 package may change over time or the thermal e 263 package may change over time or the thermal envelope it was designed for might
264 be exceeded if a turbo P-state was used for to 264 be exceeded if a turbo P-state was used for too long.
265 265
266 In turn, the P-states below the turbo threshol 266 In turn, the P-states below the turbo threshold generally are sustainable. In
267 fact, if one of them is set by software, the p 267 fact, if one of them is set by software, the processor is not expected to change
268 it to a lower one unless in a thermal stress o 268 it to a lower one unless in a thermal stress or a power limit violation
269 situation (a higher P-state may still be used 269 situation (a higher P-state may still be used if it is set for another CPU in
270 the same package at the same time, for example 270 the same package at the same time, for example).
271 271
272 Some processors allow multiple cores to be in 272 Some processors allow multiple cores to be in turbo P-states at the same time,
273 but the maximum P-state that can be set for th 273 but the maximum P-state that can be set for them generally depends on the number
274 of cores running concurrently. The maximum tu 274 of cores running concurrently. The maximum turbo P-state that can be set for 3
275 cores at the same time usually is lower than t 275 cores at the same time usually is lower than the analogous maximum P-state for
276 2 cores, which in turn usually is lower than t 276 2 cores, which in turn usually is lower than the maximum turbo P-state that can
277 be set for 1 core. The one-core maximum turbo 277 be set for 1 core. The one-core maximum turbo P-state is thus the maximum
278 supported one overall. 278 supported one overall.
279 279
280 The maximum supported turbo P-state, the turbo 280 The maximum supported turbo P-state, the turbo threshold (the maximum supported
281 non-turbo P-state) and the minimum supported P 281 non-turbo P-state) and the minimum supported P-state are specific to the
282 processor model and can be determined by readi 282 processor model and can be determined by reading the processor's model-specific
283 registers (MSRs). Moreover, some processors s 283 registers (MSRs). Moreover, some processors support the Configurable TDP
284 (Thermal Design Power) feature and, when that 284 (Thermal Design Power) feature and, when that feature is enabled, the turbo
285 threshold effectively becomes a configurable v 285 threshold effectively becomes a configurable value that can be set by the
286 platform firmware. 286 platform firmware.
287 287
288 Unlike ``_PSS`` objects in the ACPI tables, `` 288 Unlike ``_PSS`` objects in the ACPI tables, ``intel_pstate`` always exposes
289 the entire range of available P-states, includ 289 the entire range of available P-states, including the whole turbo range, to the
290 ``CPUFreq`` core and (in the passive mode) to 290 ``CPUFreq`` core and (in the passive mode) to generic scaling governors. This
291 generally causes turbo P-states to be set more 291 generally causes turbo P-states to be set more often when ``intel_pstate`` is
292 used relative to ACPI-based CPU performance sc 292 used relative to ACPI-based CPU performance scaling (see `below <acpi-cpufreq_>`_
293 for more information). 293 for more information).
294 294
295 Moreover, since ``intel_pstate`` always knows 295 Moreover, since ``intel_pstate`` always knows what the real turbo threshold is
296 (even if the Configurable TDP feature is enabl 296 (even if the Configurable TDP feature is enabled in the processor), its
297 ``no_turbo`` attribute in ``sysfs`` (described 297 ``no_turbo`` attribute in ``sysfs`` (described `below <no_turbo_attr_>`_) should
298 work as expected in all cases (that is, if set 298 work as expected in all cases (that is, if set to disable turbo P-states, it
299 always should prevent ``intel_pstate`` from us 299 always should prevent ``intel_pstate`` from using them).
300 300
301 301
302 Processor Support 302 Processor Support
303 ================= 303 =================
304 304
305 To handle a given processor ``intel_pstate`` r 305 To handle a given processor ``intel_pstate`` requires a number of different
306 pieces of information on it to be known, inclu 306 pieces of information on it to be known, including:
307 307
308 * The minimum supported P-state. 308 * The minimum supported P-state.
309 309
310 * The maximum supported `non-turbo P-state <t 310 * The maximum supported `non-turbo P-state <turbo_>`_.
311 311
312 * Whether or not turbo P-states are supported 312 * Whether or not turbo P-states are supported at all.
313 313
314 * The maximum supported `one-core turbo P-sta 314 * The maximum supported `one-core turbo P-state <turbo_>`_ (if turbo P-states
315 are supported). 315 are supported).
316 316
317 * The scaling formula to translate the driver 317 * The scaling formula to translate the driver's internal representation
318 of P-states into frequencies and the other 318 of P-states into frequencies and the other way around.
319 319
320 Generally, ways to obtain that information are 320 Generally, ways to obtain that information are specific to the processor model
321 or family. Although it often is possible to o 321 or family. Although it often is possible to obtain all of it from the processor
322 itself (using model-specific registers), there 322 itself (using model-specific registers), there are cases in which hardware
323 manuals need to be consulted to get to it too. 323 manuals need to be consulted to get to it too.
324 324
325 For this reason, there is a list of supported 325 For this reason, there is a list of supported processors in ``intel_pstate`` and
326 the driver initialization will fail if the det 326 the driver initialization will fail if the detected processor is not in that
327 list, unless it supports the HWP feature. [Th 327 list, unless it supports the HWP feature. [The interface to obtain all of the
328 information listed above is the same for all o 328 information listed above is the same for all of the processors supporting the
329 HWP feature, which is why ``intel_pstate`` wor 329 HWP feature, which is why ``intel_pstate`` works with all of them.]
330 330
331 331
332 User Space Interface in ``sysfs`` 332 User Space Interface in ``sysfs``
333 ================================= 333 =================================
334 334
335 Global Attributes 335 Global Attributes
336 ----------------- 336 -----------------
337 337
338 ``intel_pstate`` exposes several global attrib 338 ``intel_pstate`` exposes several global attributes (files) in ``sysfs`` to
339 control its functionality at the system level. 339 control its functionality at the system level. They are located in the
340 ``/sys/devices/system/cpu/intel_pstate/`` dire 340 ``/sys/devices/system/cpu/intel_pstate/`` directory and affect all CPUs.
341 341
342 Some of them are not present if the ``intel_ps 342 Some of them are not present if the ``intel_pstate=per_cpu_perf_limits``
343 argument is passed to the kernel in the comman 343 argument is passed to the kernel in the command line.
344 344
345 ``max_perf_pct`` 345 ``max_perf_pct``
346 Maximum P-state the driver is allowed 346 Maximum P-state the driver is allowed to set in percent of the
347 maximum supported performance level (t 347 maximum supported performance level (the highest supported `turbo
348 P-state <turbo_>`_). 348 P-state <turbo_>`_).
349 349
350 This attribute will not be exposed if 350 This attribute will not be exposed if the
351 ``intel_pstate=per_cpu_perf_limits`` a 351 ``intel_pstate=per_cpu_perf_limits`` argument is present in the kernel
352 command line. 352 command line.
353 353
354 ``min_perf_pct`` 354 ``min_perf_pct``
355 Minimum P-state the driver is allowed 355 Minimum P-state the driver is allowed to set in percent of the
356 maximum supported performance level (t 356 maximum supported performance level (the highest supported `turbo
357 P-state <turbo_>`_). 357 P-state <turbo_>`_).
358 358
359 This attribute will not be exposed if 359 This attribute will not be exposed if the
360 ``intel_pstate=per_cpu_perf_limits`` a 360 ``intel_pstate=per_cpu_perf_limits`` argument is present in the kernel
361 command line. 361 command line.
362 362
363 ``num_pstates`` 363 ``num_pstates``
364 Number of P-states supported by the pr 364 Number of P-states supported by the processor (between 0 and 255
365 inclusive) including both turbo and no 365 inclusive) including both turbo and non-turbo P-states (see
366 `Turbo P-states Support`_). 366 `Turbo P-states Support`_).
367 367
368 This attribute is present only if the 368 This attribute is present only if the value exposed by it is the same
369 for all of the CPUs in the system. 369 for all of the CPUs in the system.
370 370
371 The value of this attribute is not aff 371 The value of this attribute is not affected by the ``no_turbo``
372 setting described `below <no_turbo_att 372 setting described `below <no_turbo_attr_>`_.
373 373
374 This attribute is read-only. 374 This attribute is read-only.
375 375
376 ``turbo_pct`` 376 ``turbo_pct``
377 Ratio of the `turbo range <turbo_>`_ s 377 Ratio of the `turbo range <turbo_>`_ size to the size of the entire
378 range of supported P-states, in percen 378 range of supported P-states, in percent.
379 379
380 This attribute is present only if the 380 This attribute is present only if the value exposed by it is the same
381 for all of the CPUs in the system. 381 for all of the CPUs in the system.
382 382
383 This attribute is read-only. 383 This attribute is read-only.
384 384
385 .. _no_turbo_attr: 385 .. _no_turbo_attr:
386 386
387 ``no_turbo`` 387 ``no_turbo``
388 If set (equal to 1), the driver is not 388 If set (equal to 1), the driver is not allowed to set any turbo P-states
389 (see `Turbo P-states Support`_). If u 389 (see `Turbo P-states Support`_). If unset (equal to 0, which is the
390 default), turbo P-states can be set by 390 default), turbo P-states can be set by the driver.
391 [Note that ``intel_pstate`` does not s 391 [Note that ``intel_pstate`` does not support the general ``boost``
392 attribute (supported by some other sca 392 attribute (supported by some other scaling drivers) which is replaced
393 by this one.] 393 by this one.]
394 394
395 This attribute does not affect the max 395 This attribute does not affect the maximum supported frequency value
396 supplied to the ``CPUFreq`` core and e 396 supplied to the ``CPUFreq`` core and exposed via the policy interface,
397 but it affects the maximum possible va 397 but it affects the maximum possible value of per-policy P-state limits
398 (see `Interpretation of Policy Attribu 398 (see `Interpretation of Policy Attributes`_ below for details).
399 399
400 ``hwp_dynamic_boost`` 400 ``hwp_dynamic_boost``
401 This attribute is only present if ``in 401 This attribute is only present if ``intel_pstate`` works in the
402 `active mode with the HWP feature enab 402 `active mode with the HWP feature enabled <Active Mode With HWP_>`_ in
403 the processor. If set (equal to 1), i 403 the processor. If set (equal to 1), it causes the minimum P-state limit
404 to be increased dynamically for a shor 404 to be increased dynamically for a short time whenever a task previously
405 waiting on I/O is selected to run on a 405 waiting on I/O is selected to run on a given logical CPU (the purpose
406 of this mechanism is to improve perfor 406 of this mechanism is to improve performance).
407 407
408 This setting has no effect on logical 408 This setting has no effect on logical CPUs whose minimum P-state limit
409 is directly set to the highest non-tur 409 is directly set to the highest non-turbo P-state or above it.
410 410
411 .. _status_attr: 411 .. _status_attr:
412 412
413 ``status`` 413 ``status``
414 Operation mode of the driver: "active" 414 Operation mode of the driver: "active", "passive" or "off".
415 415
416 "active" 416 "active"
417 The driver is functional and i 417 The driver is functional and in the `active mode
418 <Active Mode_>`_. 418 <Active Mode_>`_.
419 419
420 "passive" 420 "passive"
421 The driver is functional and i 421 The driver is functional and in the `passive mode
422 <Passive Mode_>`_. 422 <Passive Mode_>`_.
423 423
424 "off" 424 "off"
425 The driver is not functional ( 425 The driver is not functional (it is not registered as a scaling
426 driver with the ``CPUFreq`` co 426 driver with the ``CPUFreq`` core).
427 427
428 This attribute can be written to in or 428 This attribute can be written to in order to change the driver's
429 operation mode or to unregister it. T 429 operation mode or to unregister it. The string written to it must be
430 one of the possible values of it and, 430 one of the possible values of it and, if successful, the write will
431 cause the driver to switch over to the 431 cause the driver to switch over to the operation mode represented by
432 that string - or to be unregistered in 432 that string - or to be unregistered in the "off" case. [Actually,
433 switching over from the active mode to 433 switching over from the active mode to the passive mode or the other
434 way around causes the driver to be unr 434 way around causes the driver to be unregistered and registered again
435 with a different set of callbacks, so 435 with a different set of callbacks, so all of its settings (the global
436 as well as the per-policy ones) are th 436 as well as the per-policy ones) are then reset to their default
437 values, possibly depending on the targ 437 values, possibly depending on the target operation mode.]
438 438
439 ``energy_efficiency`` 439 ``energy_efficiency``
440 This attribute is only present on plat 440 This attribute is only present on platforms with CPUs matching the Kaby
441 Lake or Coffee Lake desktop CPU model. 441 Lake or Coffee Lake desktop CPU model. By default, energy-efficiency
442 optimizations are disabled on these CP 442 optimizations are disabled on these CPU models if HWP is enabled.
443 Enabling energy-efficiency optimizatio 443 Enabling energy-efficiency optimizations may limit maximum operating
444 frequency with or without the HWP feat 444 frequency with or without the HWP feature. With HWP enabled, the
445 optimizations are done only in the tur 445 optimizations are done only in the turbo frequency range. Without it,
446 they are done in the entire available 446 they are done in the entire available frequency range. Setting this
447 attribute to "1" enables the energy-ef 447 attribute to "1" enables the energy-efficiency optimizations and setting
448 to "0" disables them. 448 to "0" disables them.
449 449
450 Interpretation of Policy Attributes 450 Interpretation of Policy Attributes
451 ----------------------------------- 451 -----------------------------------
452 452
453 The interpretation of some ``CPUFreq`` policy 453 The interpretation of some ``CPUFreq`` policy attributes described in
454 Documentation/admin-guide/pm/cpufreq.rst is sp 454 Documentation/admin-guide/pm/cpufreq.rst is special with ``intel_pstate``
455 as the current scaling driver and it generally 455 as the current scaling driver and it generally depends on the driver's
456 `operation mode <Operation Modes_>`_. 456 `operation mode <Operation Modes_>`_.
457 457
458 First of all, the values of the ``cpuinfo_max_ 458 First of all, the values of the ``cpuinfo_max_freq``, ``cpuinfo_min_freq`` and
459 ``scaling_cur_freq`` attributes are produced b 459 ``scaling_cur_freq`` attributes are produced by applying a processor-specific
460 multiplier to the internal P-state representat 460 multiplier to the internal P-state representation used by ``intel_pstate``.
461 Also, the values of the ``scaling_max_freq`` a 461 Also, the values of the ``scaling_max_freq`` and ``scaling_min_freq``
462 attributes are capped by the frequency corresp 462 attributes are capped by the frequency corresponding to the maximum P-state that
463 the driver is allowed to set. 463 the driver is allowed to set.
464 464
465 If the ``no_turbo`` `global attribute <no_turb 465 If the ``no_turbo`` `global attribute <no_turbo_attr_>`_ is set, the driver is
466 not allowed to use turbo P-states, so the maxi 466 not allowed to use turbo P-states, so the maximum value of ``scaling_max_freq``
467 and ``scaling_min_freq`` is limited to the max 467 and ``scaling_min_freq`` is limited to the maximum non-turbo P-state frequency.
468 Accordingly, setting ``no_turbo`` causes ``sca 468 Accordingly, setting ``no_turbo`` causes ``scaling_max_freq`` and
469 ``scaling_min_freq`` to go down to that value 469 ``scaling_min_freq`` to go down to that value if they were above it before.
470 However, the old values of ``scaling_max_freq` 470 However, the old values of ``scaling_max_freq`` and ``scaling_min_freq`` will be
471 restored after unsetting ``no_turbo``, unless 471 restored after unsetting ``no_turbo``, unless these attributes have been written
472 to after ``no_turbo`` was set. 472 to after ``no_turbo`` was set.
473 473
474 If ``no_turbo`` is not set, the maximum possib 474 If ``no_turbo`` is not set, the maximum possible value of ``scaling_max_freq``
475 and ``scaling_min_freq`` corresponds to the ma 475 and ``scaling_min_freq`` corresponds to the maximum supported turbo P-state,
476 which also is the value of ``cpuinfo_max_freq` 476 which also is the value of ``cpuinfo_max_freq`` in either case.
477 477
478 Next, the following policy attributes have spe 478 Next, the following policy attributes have special meaning if
479 ``intel_pstate`` works in the `active mode <Ac 479 ``intel_pstate`` works in the `active mode <Active Mode_>`_:
480 480
481 ``scaling_available_governors`` 481 ``scaling_available_governors``
482 List of P-state selection algorithms p 482 List of P-state selection algorithms provided by ``intel_pstate``.
483 483
484 ``scaling_governor`` 484 ``scaling_governor``
485 P-state selection algorithm provided b 485 P-state selection algorithm provided by ``intel_pstate`` currently in
486 use with the given policy. 486 use with the given policy.
487 487
488 ``scaling_cur_freq`` 488 ``scaling_cur_freq``
489 Frequency of the average P-state of th 489 Frequency of the average P-state of the CPU represented by the given
490 policy for the time interval between t 490 policy for the time interval between the last two invocations of the
491 driver's utilization update callback b 491 driver's utilization update callback by the CPU scheduler for that CPU.
492 492
493 One more policy attribute is present if the HW 493 One more policy attribute is present if the HWP feature is enabled in the
494 processor: 494 processor:
495 495
496 ``base_frequency`` 496 ``base_frequency``
497 Shows the base frequency of the CPU. A 497 Shows the base frequency of the CPU. Any frequency above this will be
498 in the turbo frequency range. 498 in the turbo frequency range.
499 499
500 The meaning of these attributes in the `passiv 500 The meaning of these attributes in the `passive mode <Passive Mode_>`_ is the
501 same as for other scaling drivers. 501 same as for other scaling drivers.
502 502
503 Additionally, the value of the ``scaling_drive 503 Additionally, the value of the ``scaling_driver`` attribute for ``intel_pstate``
504 depends on the operation mode of the driver. 504 depends on the operation mode of the driver. Namely, it is either
505 "intel_pstate" (in the `active mode <Active Mo 505 "intel_pstate" (in the `active mode <Active Mode_>`_) or "intel_cpufreq" (in the
506 `passive mode <Passive Mode_>`_). 506 `passive mode <Passive Mode_>`_).
507 507
508 Coordination of P-State Limits 508 Coordination of P-State Limits
509 ------------------------------ 509 ------------------------------
510 510
511 ``intel_pstate`` allows P-state limits to be s 511 ``intel_pstate`` allows P-state limits to be set in two ways: with the help of
512 the ``max_perf_pct`` and ``min_perf_pct`` `glo 512 the ``max_perf_pct`` and ``min_perf_pct`` `global attributes
513 <Global Attributes_>`_ or via the ``scaling_ma 513 <Global Attributes_>`_ or via the ``scaling_max_freq`` and ``scaling_min_freq``
514 ``CPUFreq`` policy attributes. The coordinati 514 ``CPUFreq`` policy attributes. The coordination between those limits is based
515 on the following rules, regardless of the curr 515 on the following rules, regardless of the current operation mode of the driver:
516 516
517 1. All CPUs are affected by the global limits 517 1. All CPUs are affected by the global limits (that is, none of them can be
518 requested to run faster than the global ma 518 requested to run faster than the global maximum and none of them can be
519 requested to run slower than the global mi 519 requested to run slower than the global minimum).
520 520
521 2. Each individual CPU is affected by its own 521 2. Each individual CPU is affected by its own per-policy limits (that is, it
522 cannot be requested to run faster than its 522 cannot be requested to run faster than its own per-policy maximum and it
523 cannot be requested to run slower than its 523 cannot be requested to run slower than its own per-policy minimum). The
524 effective performance depends on whether t 524 effective performance depends on whether the platform supports per core
525 P-states, hyper-threading is enabled and o 525 P-states, hyper-threading is enabled and on current performance requests
526 from other CPUs. When platform doesn't sup 526 from other CPUs. When platform doesn't support per core P-states, the
527 effective performance can be more than the 527 effective performance can be more than the policy limits set on a CPU, if
528 other CPUs are requesting higher performan 528 other CPUs are requesting higher performance at that moment. Even with per
529 core P-states support, when hyper-threadin 529 core P-states support, when hyper-threading is enabled, if the sibling CPU
530 is requesting higher performance, the othe 530 is requesting higher performance, the other siblings will get higher
531 performance than their policy limits. 531 performance than their policy limits.
532 532
533 3. The global and per-policy limits can be se 533 3. The global and per-policy limits can be set independently.
534 534
535 In the `active mode with the HWP feature enabl 535 In the `active mode with the HWP feature enabled <Active Mode With HWP_>`_, the
536 resulting effective values are written into ha 536 resulting effective values are written into hardware registers whenever the
537 limits change in order to request its internal 537 limits change in order to request its internal P-state selection logic to always
538 set P-states within these limits. Otherwise, 538 set P-states within these limits. Otherwise, the limits are taken into account
539 by scaling governors (in the `passive mode <Pa 539 by scaling governors (in the `passive mode <Passive Mode_>`_) and by the driver
540 every time before setting a new P-state for a 540 every time before setting a new P-state for a CPU.
541 541
542 Additionally, if the ``intel_pstate=per_cpu_pe 542 Additionally, if the ``intel_pstate=per_cpu_perf_limits`` command line argument
543 is passed to the kernel, ``max_perf_pct`` and 543 is passed to the kernel, ``max_perf_pct`` and ``min_perf_pct`` are not exposed
544 at all and the only way to set the limits is b 544 at all and the only way to set the limits is by using the policy attributes.
545 545
546 546
547 Energy vs Performance Hints 547 Energy vs Performance Hints
548 --------------------------- 548 ---------------------------
549 549
550 If the hardware-managed P-states (HWP) is enab 550 If the hardware-managed P-states (HWP) is enabled in the processor, additional
551 attributes, intended to allow user space to he 551 attributes, intended to allow user space to help ``intel_pstate`` to adjust the
552 processor's internal P-state selection logic b 552 processor's internal P-state selection logic by focusing it on performance or on
553 energy-efficiency, or somewhere between the tw 553 energy-efficiency, or somewhere between the two extremes, are present in every
554 ``CPUFreq`` policy directory in ``sysfs``. Th 554 ``CPUFreq`` policy directory in ``sysfs``. They are :
555 555
556 ``energy_performance_preference`` 556 ``energy_performance_preference``
557 Current value of the energy vs perform 557 Current value of the energy vs performance hint for the given policy
558 (or the CPU represented by it). 558 (or the CPU represented by it).
559 559
560 The hint can be changed by writing to 560 The hint can be changed by writing to this attribute.
561 561
562 ``energy_performance_available_preferences`` 562 ``energy_performance_available_preferences``
563 List of strings that can be written to 563 List of strings that can be written to the
564 ``energy_performance_preference`` attr 564 ``energy_performance_preference`` attribute.
565 565
566 They represent different energy vs per 566 They represent different energy vs performance hints and should be
567 self-explanatory, except that ``defaul 567 self-explanatory, except that ``default`` represents whatever hint
568 value was set by the platform firmware 568 value was set by the platform firmware.
569 569
570 Strings written to the ``energy_performance_pr 570 Strings written to the ``energy_performance_preference`` attribute are
571 internally translated to integer values writte 571 internally translated to integer values written to the processor's
572 Energy-Performance Preference (EPP) knob (if s 572 Energy-Performance Preference (EPP) knob (if supported) or its
573 Energy-Performance Bias (EPB) knob. It is also 573 Energy-Performance Bias (EPB) knob. It is also possible to write a positive
574 integer value between 0 to 255, if the EPP fea 574 integer value between 0 to 255, if the EPP feature is present. If the EPP
575 feature is not present, writing integer value 575 feature is not present, writing integer value to this attribute is not
576 supported. In this case, user can use the 576 supported. In this case, user can use the
577 "/sys/devices/system/cpu/cpu*/power/energy_per 577 "/sys/devices/system/cpu/cpu*/power/energy_perf_bias" interface.
578 578
579 [Note that tasks may by migrated from one CPU 579 [Note that tasks may by migrated from one CPU to another by the scheduler's
580 load-balancing algorithm and if different ener 580 load-balancing algorithm and if different energy vs performance hints are
581 set for those CPUs, that may lead to undesirab 581 set for those CPUs, that may lead to undesirable outcomes. To avoid such
582 issues it is better to set the same energy vs 582 issues it is better to set the same energy vs performance hint for all CPUs
583 or to pin every task potentially sensitive to 583 or to pin every task potentially sensitive to them to a specific CPU.]
584 584
585 .. _acpi-cpufreq: 585 .. _acpi-cpufreq:
586 586
587 ``intel_pstate`` vs ``acpi-cpufreq`` 587 ``intel_pstate`` vs ``acpi-cpufreq``
588 ==================================== 588 ====================================
589 589
590 On the majority of systems supported by ``inte 590 On the majority of systems supported by ``intel_pstate``, the ACPI tables
591 provided by the platform firmware contain ``_P 591 provided by the platform firmware contain ``_PSS`` objects returning information
592 that can be used for CPU performance scaling ( 592 that can be used for CPU performance scaling (refer to the ACPI specification
593 [3]_ for details on the ``_PSS`` objects and t 593 [3]_ for details on the ``_PSS`` objects and the format of the information
594 returned by them). 594 returned by them).
595 595
596 The information returned by the ACPI ``_PSS`` 596 The information returned by the ACPI ``_PSS`` objects is used by the
597 ``acpi-cpufreq`` scaling driver. On systems s 597 ``acpi-cpufreq`` scaling driver. On systems supported by ``intel_pstate``
598 the ``acpi-cpufreq`` driver uses the same hard 598 the ``acpi-cpufreq`` driver uses the same hardware CPU performance scaling
599 interface, but the set of P-states it can use 599 interface, but the set of P-states it can use is limited by the ``_PSS``
600 output. 600 output.
601 601
602 On those systems each ``_PSS`` object returns 602 On those systems each ``_PSS`` object returns a list of P-states supported by
603 the corresponding CPU which basically is a sub 603 the corresponding CPU which basically is a subset of the P-states range that can
604 be used by ``intel_pstate`` on the same system 604 be used by ``intel_pstate`` on the same system, with one exception: the whole
605 `turbo range <turbo_>`_ is represented by one 605 `turbo range <turbo_>`_ is represented by one item in it (the topmost one). By
606 convention, the frequency returned by ``_PSS`` 606 convention, the frequency returned by ``_PSS`` for that item is greater by 1 MHz
607 than the frequency of the highest non-turbo P- 607 than the frequency of the highest non-turbo P-state listed by it, but the
608 corresponding P-state representation (followin 608 corresponding P-state representation (following the hardware specification)
609 returned for it matches the maximum supported 609 returned for it matches the maximum supported turbo P-state (or is the
610 special value 255 meaning essentially "go as h 610 special value 255 meaning essentially "go as high as you can get").
611 611
612 The list of P-states returned by ``_PSS`` is r 612 The list of P-states returned by ``_PSS`` is reflected by the table of
613 available frequencies supplied by ``acpi-cpufr 613 available frequencies supplied by ``acpi-cpufreq`` to the ``CPUFreq`` core and
614 scaling governors and the minimum and maximum 614 scaling governors and the minimum and maximum supported frequencies reported by
615 it come from that list as well. In particular 615 it come from that list as well. In particular, given the special representation
616 of the turbo range described above, this means 616 of the turbo range described above, this means that the maximum supported
617 frequency reported by ``acpi-cpufreq`` is high 617 frequency reported by ``acpi-cpufreq`` is higher by 1 MHz than the frequency
618 of the highest supported non-turbo P-state lis 618 of the highest supported non-turbo P-state listed by ``_PSS`` which, of course,
619 affects decisions made by the scaling governor 619 affects decisions made by the scaling governors, except for ``powersave`` and
620 ``performance``. 620 ``performance``.
621 621
622 For example, if a given governor attempts to s 622 For example, if a given governor attempts to select a frequency proportional to
623 estimated CPU load and maps the load of 100% t 623 estimated CPU load and maps the load of 100% to the maximum supported frequency
624 (possibly multiplied by a constant), then it w 624 (possibly multiplied by a constant), then it will tend to choose P-states below
625 the turbo threshold if ``acpi-cpufreq`` is use 625 the turbo threshold if ``acpi-cpufreq`` is used as the scaling driver, because
626 in that case the turbo range corresponds to a 626 in that case the turbo range corresponds to a small fraction of the frequency
627 band it can use (1 MHz vs 1 GHz or more). In 627 band it can use (1 MHz vs 1 GHz or more). In consequence, it will only go to
628 the turbo range for the highest loads and the 628 the turbo range for the highest loads and the other loads above 50% that might
629 benefit from running at turbo frequencies will 629 benefit from running at turbo frequencies will be given non-turbo P-states
630 instead. 630 instead.
631 631
632 One more issue related to that may appear on s 632 One more issue related to that may appear on systems supporting the
633 `Configurable TDP feature <turbo_>`_ allowing 633 `Configurable TDP feature <turbo_>`_ allowing the platform firmware to set the
634 turbo threshold. Namely, if that is not coord 634 turbo threshold. Namely, if that is not coordinated with the lists of P-states
635 returned by ``_PSS`` properly, there may be mo 635 returned by ``_PSS`` properly, there may be more than one item corresponding to
636 a turbo P-state in those lists and there may b 636 a turbo P-state in those lists and there may be a problem with avoiding the
637 turbo range (if desirable or necessary). Usua 637 turbo range (if desirable or necessary). Usually, to avoid using turbo
638 P-states overall, ``acpi-cpufreq`` simply avoi 638 P-states overall, ``acpi-cpufreq`` simply avoids using the topmost state listed
639 by ``_PSS``, but that is not sufficient when t 639 by ``_PSS``, but that is not sufficient when there are other turbo P-states in
640 the list returned by it. 640 the list returned by it.
641 641
642 Apart from the above, ``acpi-cpufreq`` works l 642 Apart from the above, ``acpi-cpufreq`` works like ``intel_pstate`` in the
643 `passive mode <Passive Mode_>`_, except that t 643 `passive mode <Passive Mode_>`_, except that the number of P-states it can set
644 is limited to the ones listed by the ACPI ``_P 644 is limited to the ones listed by the ACPI ``_PSS`` objects.
645 645
646 646
647 Kernel Command Line Options for ``intel_pstate 647 Kernel Command Line Options for ``intel_pstate``
648 ============================================== 648 ================================================
649 649
650 Several kernel command line options can be use 650 Several kernel command line options can be used to pass early-configuration-time
651 parameters to ``intel_pstate`` in order to enf 651 parameters to ``intel_pstate`` in order to enforce specific behavior of it. All
652 of them have to be prepended with the ``intel_ 652 of them have to be prepended with the ``intel_pstate=`` prefix.
653 653
654 ``disable`` 654 ``disable``
655 Do not register ``intel_pstate`` as th 655 Do not register ``intel_pstate`` as the scaling driver even if the
656 processor is supported by it. 656 processor is supported by it.
657 657
658 ``active`` 658 ``active``
659 Register ``intel_pstate`` in the `acti 659 Register ``intel_pstate`` in the `active mode <Active Mode_>`_ to start
660 with. 660 with.
661 661
662 ``passive`` 662 ``passive``
663 Register ``intel_pstate`` in the `pass 663 Register ``intel_pstate`` in the `passive mode <Passive Mode_>`_ to
664 start with. 664 start with.
665 665
666 ``force`` 666 ``force``
667 Register ``intel_pstate`` as the scali 667 Register ``intel_pstate`` as the scaling driver instead of
668 ``acpi-cpufreq`` even if the latter is 668 ``acpi-cpufreq`` even if the latter is preferred on the given system.
669 669
670 This may prevent some platform feature 670 This may prevent some platform features (such as thermal controls and
671 power capping) that rely on the availa 671 power capping) that rely on the availability of ACPI P-states
672 information from functioning as expect 672 information from functioning as expected, so it should be used with
673 caution. 673 caution.
674 674
675 This option does not work with process 675 This option does not work with processors that are not supported by
676 ``intel_pstate`` and on platforms wher 676 ``intel_pstate`` and on platforms where the ``pcc-cpufreq`` scaling
677 driver is used instead of ``acpi-cpufr 677 driver is used instead of ``acpi-cpufreq``.
678 678
679 ``no_hwp`` 679 ``no_hwp``
680 Do not enable the hardware-managed P-s 680 Do not enable the hardware-managed P-states (HWP) feature even if it is
681 supported by the processor. 681 supported by the processor.
682 682
683 ``hwp_only`` 683 ``hwp_only``
684 Register ``intel_pstate`` as the scali 684 Register ``intel_pstate`` as the scaling driver only if the
685 hardware-managed P-states (HWP) featur 685 hardware-managed P-states (HWP) feature is supported by the processor.
686 686
687 ``support_acpi_ppc`` 687 ``support_acpi_ppc``
688 Take ACPI ``_PPC`` performance limits 688 Take ACPI ``_PPC`` performance limits into account.
689 689
690 If the preferred power management prof 690 If the preferred power management profile in the FADT (Fixed ACPI
691 Description Table) is set to "Enterpri 691 Description Table) is set to "Enterprise Server" or "Performance
692 Server", the ACPI ``_PPC`` limits are 692 Server", the ACPI ``_PPC`` limits are taken into account by default
693 and this option has no effect. 693 and this option has no effect.
694 694
695 ``per_cpu_perf_limits`` 695 ``per_cpu_perf_limits``
696 Use per-logical-CPU P-State limits (se 696 Use per-logical-CPU P-State limits (see `Coordination of P-state
697 Limits`_ for details). 697 Limits`_ for details).
698 698
699 699
700 Diagnostics and Tuning 700 Diagnostics and Tuning
701 ====================== 701 ======================
702 702
703 Trace Events 703 Trace Events
704 ------------ 704 ------------
705 705
706 There are two static trace events that can be 706 There are two static trace events that can be used for ``intel_pstate``
707 diagnostics. One of them is the ``cpu_frequen 707 diagnostics. One of them is the ``cpu_frequency`` trace event generally used
708 by ``CPUFreq``, and the other one is the ``pst 708 by ``CPUFreq``, and the other one is the ``pstate_sample`` trace event specific
709 to ``intel_pstate``. Both of them are trigger 709 to ``intel_pstate``. Both of them are triggered by ``intel_pstate`` only if
710 it works in the `active mode <Active Mode_>`_. 710 it works in the `active mode <Active Mode_>`_.
711 711
712 The following sequence of shell commands can b 712 The following sequence of shell commands can be used to enable them and see
713 their output (if the kernel is generally confi 713 their output (if the kernel is generally configured to support event tracing)::
714 714
715 # cd /sys/kernel/tracing/ 715 # cd /sys/kernel/tracing/
716 # echo 1 > events/power/pstate_sample/enable 716 # echo 1 > events/power/pstate_sample/enable
717 # echo 1 > events/power/cpu_frequency/enable 717 # echo 1 > events/power/cpu_frequency/enable
718 # cat trace 718 # cat trace
719 gnome-terminal--4510 [001] ..s. 1177.680733 719 gnome-terminal--4510 [001] ..s. 1177.680733: pstate_sample: core_busy=107 scaled=94 from=26 to=26 mperf=1143818 aperf=1230607 tsc=29838618 freq=2474476
720 cat-5235 [002] ..s. 1177.681723: cpu_freque 720 cat-5235 [002] ..s. 1177.681723: cpu_frequency: state=2900000 cpu_id=2
721 721
722 If ``intel_pstate`` works in the `passive mode 722 If ``intel_pstate`` works in the `passive mode <Passive Mode_>`_, the
723 ``cpu_frequency`` trace event will be triggere 723 ``cpu_frequency`` trace event will be triggered either by the ``schedutil``
724 scaling governor (for the policies it is attac 724 scaling governor (for the policies it is attached to), or by the ``CPUFreq``
725 core (for the policies with other scaling gove 725 core (for the policies with other scaling governors).
726 726
727 ``ftrace`` 727 ``ftrace``
728 ---------- 728 ----------
729 729
730 The ``ftrace`` interface can be used for low-l 730 The ``ftrace`` interface can be used for low-level diagnostics of
731 ``intel_pstate``. For example, to check how o 731 ``intel_pstate``. For example, to check how often the function to set a
732 P-state is called, the ``ftrace`` filter can b 732 P-state is called, the ``ftrace`` filter can be set to
733 :c:func:`intel_pstate_set_pstate`:: 733 :c:func:`intel_pstate_set_pstate`::
734 734
735 # cd /sys/kernel/tracing/ 735 # cd /sys/kernel/tracing/
736 # cat available_filter_functions | grep -i ps 736 # cat available_filter_functions | grep -i pstate
737 intel_pstate_set_pstate 737 intel_pstate_set_pstate
738 intel_pstate_cpu_init 738 intel_pstate_cpu_init
739 ... 739 ...
740 # echo intel_pstate_set_pstate > set_ftrace_f 740 # echo intel_pstate_set_pstate > set_ftrace_filter
741 # echo function > current_tracer 741 # echo function > current_tracer
742 # cat trace | head -15 742 # cat trace | head -15
743 # tracer: function 743 # tracer: function
744 # 744 #
745 # entries-in-buffer/entries-written: 80/80 745 # entries-in-buffer/entries-written: 80/80 #P:4
746 # 746 #
747 # _-----=> irqs- 747 # _-----=> irqs-off
748 # / _----=> need- 748 # / _----=> need-resched
749 # | / _---=> hardi 749 # | / _---=> hardirq/softirq
750 # || / _--=> preem 750 # || / _--=> preempt-depth
751 # ||| / delay 751 # ||| / delay
752 # TASK-PID CPU# |||| TIMESTAM 752 # TASK-PID CPU# |||| TIMESTAMP FUNCTION
753 # | | | |||| | 753 # | | | |||| | |
754 Xorg-3129 [000] ..s. 2537.64484 754 Xorg-3129 [000] ..s. 2537.644844: intel_pstate_set_pstate <-intel_pstate_timer_func
755 gnome-terminal--4510 [002] ..s. 2537.64984 755 gnome-terminal--4510 [002] ..s. 2537.649844: intel_pstate_set_pstate <-intel_pstate_timer_func
756 gnome-shell-3409 [001] ..s. 2537.65085 756 gnome-shell-3409 [001] ..s. 2537.650850: intel_pstate_set_pstate <-intel_pstate_timer_func
757 <idle>-0 [000] ..s. 2537.65484 757 <idle>-0 [000] ..s. 2537.654843: intel_pstate_set_pstate <-intel_pstate_timer_func
758 758
759 759
760 References 760 References
761 ========== 761 ==========
762 762
763 .. [1] Kristen Accardi, *Balancing Power and P 763 .. [1] Kristen Accardi, *Balancing Power and Performance in the Linux Kernel*,
764 https://events.static.linuxfound.org/si 764 https://events.static.linuxfound.org/sites/events/files/slides/LinuxConEurope_2015.pdf
765 765
766 .. [2] *Intel® 64 and IA-32 Architectures Sof 766 .. [2] *Intel® 64 and IA-32 Architectures Software Developer’s Manual Volume 3: System Programming Guide*,
767 https://www.intel.com/content/www/us/en 767 https://www.intel.com/content/www/us/en/architecture-and-technology/64-ia-32-architectures-software-developer-system-programming-manual-325384.html
768 768
769 .. [3] *Advanced Configuration and Power Inter 769 .. [3] *Advanced Configuration and Power Interface Specification*,
770 https://uefi.org/sites/default/files/re 770 https://uefi.org/sites/default/files/resources/ACPI_6_3_final_Jan30.pdf
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.