1 Cirrus Logic/Wolfson Microelectronics wm831x P 1 Cirrus Logic/Wolfson Microelectronics wm831x PMICs
2 2
3 System PMICs with a wide range of additional f 3 System PMICs with a wide range of additional features.
4 4
5 Required properties: 5 Required properties:
6 6
7 - compatible : One of the following chip-spe 7 - compatible : One of the following chip-specific strings:
8 "wlf,wm8310" 8 "wlf,wm8310"
9 "wlf,wm8311" 9 "wlf,wm8311"
10 "wlf,wm8312" 10 "wlf,wm8312"
11 "wlf,wm8320" 11 "wlf,wm8320"
12 "wlf,wm8321" 12 "wlf,wm8321"
13 "wlf,wm8325" 13 "wlf,wm8325"
14 "wlf,wm8326" 14 "wlf,wm8326"
15 15
16 - reg : I2C slave address when connected usi 16 - reg : I2C slave address when connected using I2C, chip select number
17 when using SPI. 17 when using SPI.
18 18
19 - gpio-controller : Indicates this device is 19 - gpio-controller : Indicates this device is a GPIO controller.
20 - #gpio-cells : Must be 2. The first cell is 20 - #gpio-cells : Must be 2. The first cell is the pin number and the
21 second cell is used to specify optional pa 21 second cell is used to specify optional parameters (currently unused).
22 22
23 - interrupts : The interrupt line the IRQ si 23 - interrupts : The interrupt line the IRQ signal for the device is
24 connected to. 24 connected to.
25 25
26 - interrupt-controller : wm831x devices cont 26 - interrupt-controller : wm831x devices contain interrupt controllers and
27 may provide interrupt services to other de 27 may provide interrupt services to other devices.
28 - #interrupt-cells: Must be 2. The first cel 28 - #interrupt-cells: Must be 2. The first cell is the IRQ number, and the
29 second cell is the flags, encoded as the t 29 second cell is the flags, encoded as the trigger masks from
30 ../interrupt-controller/interrupts.txt 30 ../interrupt-controller/interrupts.txt
31 31
32 Optional sub-nodes: 32 Optional sub-nodes:
33 - phys : Contains a phandle to the USB PHY. 33 - phys : Contains a phandle to the USB PHY.
34 - regulators : Contains sub-nodes for each o 34 - regulators : Contains sub-nodes for each of the regulators supplied by
35 the device. The regulators are bound using 35 the device. The regulators are bound using their names listed below:
36 36
37 dcdc1 : DCDC1 37 dcdc1 : DCDC1
38 dcdc2 : DCDC2 38 dcdc2 : DCDC2
39 dcdc3 : DCDC3 39 dcdc3 : DCDC3
40 dcdc4 : DCDC3 40 dcdc4 : DCDC3
41 isink1 : ISINK1 41 isink1 : ISINK1
42 isink2 : ISINK2 42 isink2 : ISINK2
43 ldo1 : LDO1 43 ldo1 : LDO1
44 ldo2 : LDO2 44 ldo2 : LDO2
45 ldo3 : LDO3 45 ldo3 : LDO3
46 ldo4 : LDO4 46 ldo4 : LDO4
47 ldo5 : LDO5 47 ldo5 : LDO5
48 ldo7 : LDO7 48 ldo7 : LDO7
49 ldo11 : LDO11 49 ldo11 : LDO11
50 50
51 The bindings details of each regulator can 51 The bindings details of each regulator can be found in:
52 ../regulator/regulator.txt 52 ../regulator/regulator.txt
53 53
54 Example: 54 Example:
55 55
56 wm8310: pmic@36 { 56 wm8310: pmic@36 {
57 compatible = "wlf,wm8310"; 57 compatible = "wlf,wm8310";
58 reg = <0x36>; 58 reg = <0x36>;
59 59
60 gpio-controller; 60 gpio-controller;
61 #gpio-cells = <2>; 61 #gpio-cells = <2>;
62 62
63 interrupts = <347>; 63 interrupts = <347>;
64 interrupt-parent = <&gic>; 64 interrupt-parent = <&gic>;
65 65
66 interrupt-controller; 66 interrupt-controller;
67 #interrupt-cells = <2>; 67 #interrupt-cells = <2>;
68 68
69 regulators { 69 regulators {
70 dcdc1: dcdc1 { 70 dcdc1: dcdc1 {
71 regulator-name = "DCDC 71 regulator-name = "DCDC1";
72 regulator-min-microvol 72 regulator-min-microvolt = <600000>;
73 regulator-max-microvol 73 regulator-max-microvolt = <600000>;
74 }; 74 };
75 ldo1: ldo1 { 75 ldo1: ldo1 {
76 regulator-name = "LDO1 76 regulator-name = "LDO1";
77 regulator-min-microvol 77 regulator-min-microvolt = <1700000>;
78 regulator-max-microvol 78 regulator-max-microvolt = <1700000>;
79 }; 79 };
80 }; 80 };
81 }; 81 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.