1 CS42L52 audio CODEC 1 CS42L52 audio CODEC
2 2
3 Required properties: 3 Required properties:
4 4
5 - compatible : "cirrus,cs42l56" 5 - compatible : "cirrus,cs42l56"
6 6
7 - reg : the I2C address of the device for I2 7 - reg : the I2C address of the device for I2C
8 8
9 - VA-supply, VCP-supply, VLDO-supply : power 9 - VA-supply, VCP-supply, VLDO-supply : power supplies for the device,
10 as covered in Documentation/devicetree/bindi 10 as covered in Documentation/devicetree/bindings/regulator/regulator.txt.
11 11
12 Optional properties: 12 Optional properties:
13 13
14 - cirrus,gpio-nreset : GPIO controller's pha 14 - cirrus,gpio-nreset : GPIO controller's phandle and the number
15 of the GPIO used to reset the codec. 15 of the GPIO used to reset the codec.
16 16
17 - cirrus,chgfreq-divisor : Values used to se 17 - cirrus,chgfreq-divisor : Values used to set the Charge Pump Frequency.
18 Allowable values of 0x00 through 0x0F. These 18 Allowable values of 0x00 through 0x0F. These are raw values written to the
19 register, not the actual frequency. The freq 19 register, not the actual frequency. The frequency is determined by the following.
20 Frequency = MCLK / 4 * (N+2) 20 Frequency = MCLK / 4 * (N+2)
21 N = chgfreq_val 21 N = chgfreq_val
22 MCLK = Where MCLK is the frequency of the mc 22 MCLK = Where MCLK is the frequency of the mclk signal after the MCLKDIV2 circuit.
23 23
24 - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : bool 24 - cirrus,ain1a-ref-cfg, ain1b-ref-cfg : boolean, If present, AIN1A or AIN1B are configured
25 as a pseudo-differential input referenced to 25 as a pseudo-differential input referenced to AIN1REF/AIN3A.
26 26
27 - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : bool 27 - cirrus,ain2a-ref-cfg, ain2b-ref-cfg : boolean, If present, AIN2A or AIN2B are configured
28 as a pseudo-differential input referenced to 28 as a pseudo-differential input referenced to AIN2REF/AIN3B.
29 29
30 - cirrus,micbias-lvl: Set the output voltage 30 - cirrus,micbias-lvl: Set the output voltage level on the MICBIAS Pin.
31 0 = 0.5 x VA 31 0 = 0.5 x VA
32 1 = 0.6 x VA 32 1 = 0.6 x VA
33 2 = 0.7 x VA 33 2 = 0.7 x VA
34 3 = 0.8 x VA 34 3 = 0.8 x VA
35 4 = 0.83 x VA 35 4 = 0.83 x VA
36 5 = 0.91 x VA 36 5 = 0.91 x VA
37 37
38 - cirrus,adaptive-pwr-cfg : Configures how t 38 - cirrus,adaptive-pwr-cfg : Configures how the power to the Headphone and Lineout
39 Amplifiers adapt to the output signal levels 39 Amplifiers adapt to the output signal levels.
40 0 = Adapt to Volume Mode. Voltage level dete 40 0 = Adapt to Volume Mode. Voltage level determined by the sum of the relevant volume settings.
41 1 = Fixed - Headphone and Line Amp supply = 41 1 = Fixed - Headphone and Line Amp supply = + or - VCP/2.
42 2 = Fixed - Headphone and Line Amp supply = 42 2 = Fixed - Headphone and Line Amp supply = + or - VCP.
43 3 = Adapted to Signal; Voltage level is dyna 43 3 = Adapted to Signal; Voltage level is dynamically determined by the output signal.
44 44
45 - cirrus,hpf-left-freq, hpf-right-freq : Set 45 - cirrus,hpf-left-freq, hpf-right-freq : Sets the corner frequency (-3dB point) for the internal High-Pass
46 Filter. 46 Filter.
47 0 = 1.8Hz 47 0 = 1.8Hz
48 1 = 119Hz 48 1 = 119Hz
49 2 = 236Hz 49 2 = 236Hz
50 3 = 464Hz 50 3 = 464Hz
51 51
52 52
53 Example: 53 Example:
54 54
55 codec: codec@4b { 55 codec: codec@4b {
56 compatible = "cirrus,cs42l56"; 56 compatible = "cirrus,cs42l56";
57 reg = <0x4b>; 57 reg = <0x4b>;
58 cirrus,gpio-nreset = <&gpio 10 0>; 58 cirrus,gpio-nreset = <&gpio 10 0>;
59 cirrus,chgfreq-divisor = <0x05>; 59 cirrus,chgfreq-divisor = <0x05>;
60 cirrus.ain1_ref_cfg; 60 cirrus.ain1_ref_cfg;
61 cirrus,micbias-lvl = <5>; 61 cirrus,micbias-lvl = <5>;
62 VA-supply = <®_audio>; 62 VA-supply = <®_audio>;
63 }; 63 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.