1 OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS
2
3 OMAP MUSB GLUE
4 - compatible : Should be "ti,omap4-musb" or "
5 - ti,hwmods : must be "usb_otg_hs"
6 - multipoint : Should be "1" indicating the m
7 multipoint. This is a MUSB configuration-sp
8 - num-eps : Specifies the number of endpoints
9 MUSB configuration-specific setting. Should
10 - ram-bits : Specifies the ram address size.
11 - interface-type : This is a board specific s
12 interface between the controller and the ph
13 specifying ULPI and UTMI respectively.
14 - mode : Should be "3" to represent OTG. "1"
15 represents PERIPHERAL.
16 - power : Should be "50". This signifies the
17 100mA when operating in host mode.
18 - usb-phy : the phandle for the PHY device
19 - phys : the phandle for the PHY device (used
20 - phy-names : the names of the PHY correspond
21 *phy* phandle.
22
23 Optional properties:
24 - ctrl-module : phandle of the control module
25 mailbox
26
27 SOC specific device node entry
28 usb_otg_hs: usb_otg_hs@4a0ab000 {
29 compatible = "ti,omap4-musb";
30 ti,hwmods = "usb_otg_hs";
31 multipoint = <1>;
32 num-eps = <16>;
33 ram-bits = <12>;
34 ctrl-module = <&omap_control_usb>;
35 phys = <&usb2_phy>;
36 phy-names = "usb2-phy";
37 };
38
39 Board specific device node entry
40 &usb_otg_hs {
41 interface-type = <1>;
42 mode = <3>;
43 power = <50>;
44 };
45
46 OMAP DWC3 GLUE
47 - compatible : Should be
48 * "ti,dwc3" for OMAP5 and DRA7
49 * "ti,am437x-dwc3" for AM437x
50 - ti,hwmods : Should be "usb_otg_ss"
51 - reg : Address and length of the register se
52 - interrupts : The irq number of this device
53 MPU
54 - #address-cells, #size-cells : Must be prese
55 - utmi-mode : controls the source of UTMI/PIP
56 It should be set to "1" for HW mode and "2"
57 - ranges: the child address space are mapped
58
59 Optional Properties:
60 - extcon : phandle for the extcon device omap
61 connect/disconnect events.
62 - vbus-supply : phandle to the regulator devi
63
64 Sub-nodes:
65 The dwc3 core should be added as subnode to om
66 - dwc3 :
67 The binding details of dwc3 can be found in
68 Documentation/devicetree/bindings/usb/snps,
69
70 omap_dwc3 {
71 compatible = "ti,dwc3";
72 ti,hwmods = "usb_otg_ss";
73 reg = <0x4a020000 0x1ff>;
74 interrupts = <0 93 4>;
75 #address-cells = <1>;
76 #size-cells = <1>;
77 utmi-mode = <2>;
78 ranges;
79 };
80
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.