1 .. SPDX-License-Identifier: GPL-2.0
2
3 ===========================
4 NCR53C8XX/SYM53C8XX drivers
5 ===========================
6
7 Written by Gerard Roudier <groudier@free.fr>
8
9 21 Rue Carnot
10
11 95170 DEUIL LA BARRE - FRANCE
12
13 29 May 1999
14
15 .. Contents:
16
17 1. Introduction
18 2. Supported chips and SCSI features
19 3. Advantages of the enhanced 896 driver
20 3.1 Optimized SCSI SCRIPTS
21 3.2 New features of the SYM53C896 (64
22 4. Memory mapped I/O versus normal I/O
23 5. Tagged command queueing
24 6. Parity checking
25 7. Profiling information
26 8. Control commands
27 8.1 Set minimum synchronous period
28 8.2 Set wide size
29 8.3 Set maximum number of concurrent
30 8.4 Set order type for tagged comman
31 8.5 Set debug mode
32 8.6 Clear profile counters
33 8.7 Set flag (no_disc)
34 8.8 Set verbose level
35 8.9 Reset all logical units of a tar
36 8.10 Abort all tasks of all logical u
37 9. Configuration parameters
38 10. Boot setup commands
39 10.1 Syntax
40 10.2 Available arguments
41 10.2.1 Master parity checking
42 10.2.2 Scsi parity checking
43 10.2.3 Scsi disconnections
44 10.2.4 Special features
45 10.2.5 Ultra SCSI support
46 10.2.6 Default number of tagg
47 10.2.7 Default synchronous pe
48 10.2.8 Negotiate synchronous
49 10.2.9 Verbosity level
50 10.2.10 Debug mode
51 10.2.11 Burst max
52 10.2.12 LED support
53 10.2.13 Max wide
54 10.2.14 Differential mode
55 10.2.15 IRQ mode
56 10.2.16 Reverse probe
57 10.2.17 Fix up PCI configurati
58 10.2.18 Serial NVRAM
59 10.2.19 Check SCSI BUS
60 10.2.20 Exclude a host from be
61 10.2.21 Suggest a default SCSI
62 10.2.22 Enable use of IMMEDIAT
63 10.3 Advised boot setup commands
64 10.4 PCI configuration fix-up boot op
65 10.5 Serial NVRAM support boot option
66 10.6 SCSI BUS checking boot option
67 10.7 IMMEDIATE ARBITRATION boot optio
68 11. Some constants and flags of the ncr53c8
69 12. Installation
70 13. Architecture dependent features
71 14. Known problems
72 14.1 Tagged commands with Iomega Jaz
73 14.2 Device names change when another
74 14.3 Using only 8 bit devices with a
75 14.4 Possible data corruption during
76 14.5 IRQ sharing problems
77 15. SCSI problem troubleshooting
78 15.1 Problem tracking
79 15.2 Understanding hardware error rep
80 16. Synchronous transfer negotiation tables
81 16.1 Synchronous timings for 53C875 a
82 16.2 Synchronous timings for fast SCS
83 17. Serial NVRAM support (by Richard Waltha
84 17.1 Features
85 17.2 Symbios NVRAM layout
86 17.3 Tekram NVRAM layout
87 18. Support for Big Endian
88 18.1 Big Endian CPU
89 18.2 NCR chip in Big Endian mode of o
90
91 1. Introduction
92 ===============
93
94 The initial Linux ncr53c8xx driver has been a
95 FreeBSD that has been achieved in November 199
96
97 - Gerard Roudier <groudier
98
99 The original driver has been written for 386bs
100
101 - Wolfgang Stanglmeier <wolf@col
102 - Stefan Esser <se@mi.Un
103
104 It is now available as a bundle of 2 drivers:
105
106 - ncr53c8xx generic driver that supports all t
107 the earliest 810 rev. 1, the latest 896 (2 c
108 the new 895A (1 channel LVD SCSI controller)
109 - sym53c8xx enhanced driver (a.k.a. 896 driver
110 chips in order to gain advantage of new feat
111 available since the 810A and hardware phase
112 896 and the 895A.
113
114 You can find technical information about the N
115 PCI-HOWTO written by Michael Will and in the S
116 Drew Eckhardt.
117
118 Information about new chips is available at LS
119
120 - http://www.lsilogic.com/
121
122 SCSI standard documentations are available at
123
124 - ftp://ftp.symbios.com/
125
126 Useful SCSI tools written by Eric Youngdale ar
127
128 - ftp://tsx-11.mit.edu/pub/linux/ALP
129 - ftp://tsx-11.mit.edu/pub/linux/ALP
130
131 These tools are not ALPHA but quite clean and
132 It is essential you have the 'scsiinfo' packag
133
134 This short documentation describes the feature
135 drivers, configuration parameters and control
136 the proc SCSI file system read / write operati
137
138 This driver has been tested OK with linux/i386
139
140 Latest driver version and patches are availabl
141
142 - ftp://ftp.tux.org/pub/people/gerar
143
144 or
145
146 - ftp://ftp.symbios.com/mirror/ftp.t
147
148 I am not a native speaker of English and there
149 mistakes in this README file. Any help will be
150
151
152 2. Supported chips and SCSI features
153 ====================================
154
155 The following features are supported for all c
156
157 - Synchronous negotiation
158 - Disconnection
159 - Tagged command queuing
160 - SCSI parity checking
161 - Master parity checking
162
163 "Wide negotiation" is supported for chips that
164 following table shows some characteristics of
165 and what drivers support them.
166
167 +--------+-----------+-----+-----------+------
168 | | | | |
169 | |On board | | |
170 |Chip |SDMS BIOS |Wide |SCSI std. | Max.
171 +--------+-----------+-----+-----------+------
172 |810 | N | N | FAST10 | 10 MB
173 +--------+-----------+-----+-----------+------
174 |810A | N | N | FAST10 | 10 MB
175 +--------+-----------+-----+-----------+------
176 |815 | Y | N | FAST10 | 10 MB
177 +--------+-----------+-----+-----------+------
178 |825 | Y | Y | FAST10 | 20 MB
179 +--------+-----------+-----+-----------+------
180 |825A | Y | Y | FAST10 | 20 MB
181 +--------+-----------+-----+-----------+------
182 |860 | N | N | FAST20 | 20 MB
183 +--------+-----------+-----+-----------+------
184 |875 | Y | Y | FAST20 | 40 MB
185 +--------+-----------+-----+-----------+------
186 |876 | Y | Y | FAST20 | 40 MB
187 +--------+-----------+-----+-----------+------
188 |895 | Y | Y | FAST40 | 80 MB
189 +--------+-----------+-----+-----------+------
190 |895A | Y | Y | FAST40 | 80 MB
191 +--------+-----------+-----+-----------+------
192 |896 | Y | Y | FAST40 | 80 MB
193 +--------+-----------+-----+-----------+------
194 |897 | Y | Y | FAST40 | 80 MB
195 +--------+-----------+-----+-----------+------
196 |1510D | Y | Y | FAST40 | 80 MB
197 +--------+-----------+-----+-----------+------
198 |1010 | Y | Y | FAST80 |160 MB
199 +--------+-----------+-----+-----------+------
200 |1010_66 | Y | Y | FAST80 |160 MB
201 |[1]_ | | | |
202 +--------+-----------+-----+-----------+------
203
204 .. [1] Chip supports 33MHz and 66MHz PCI buses
205
206
207 Summary of other supported features:
208
209 :Module: allow to load the driv
210 :Memory mapped I/O: increases performance
211 :Profiling information: read operations from t
212 :Control commands: write operations to th
213 :Debugging information: written to syslog (exp
214 :Serial NVRAM: Symbios and Tekram for
215
216 - Scatter / gather
217 - Shared interrupt
218 - Boot setup commands
219
220
221 3. Advantages of the enhanced 896 driver
222 ========================================
223
224 3.1 Optimized SCSI SCRIPTS
225 --------------------------
226
227 The 810A, 825A, 875, 895, 896 and 895A support
228 named LOAD and STORE that allow to move up to
229 to/from memory much faster that the MOVE MEMOR
230 by the 53c7xx and 53c8xx family.
231 The LOAD/STORE instructions support absolute a
232 modes. The SCSI SCRIPTS had been entirely rew
233 of MOVE MEMORY instructions.
234
235 3.2 New features of the SYM53C896 (64 bit PCI
236 ----------------------------------------------
237
238 The 896 and the 895A allows handling of the ph
239 SCRIPTS (avoids the phase mismatch interrupt t
240 until the C code has saved the context of the
241 Implementing this without using LOAD/STORE ins
242 and I didn't even want to try it.
243
244 The 896 chip supports 64 bit PCI transactions
245 895A supports 32 bit PCI transactions and 64 b
246 The SCRIPTS processor of these chips is not tr
247 registers for bit 32-63. Another interesting f
248 instructions that address the on-chip RAM (8k)
249
250 Due to the use of LOAD/STORE SCRIPTS instructi
251 support the following chips:
252
253 - SYM53C810 revision < 0x10 (16)
254 - SYM53C815 all revisions
255 - SYM53C825 revision < 0x10 (16)
256
257 4. Memory mapped I/O versus normal I/O
258 ======================================
259
260 Memory mapped I/O has less latency than normal
261 linux-1.3.x, memory mapped I/O is used rather
262 mapped I/O seems to work fine on most hardware
263 some poorly designed motherboards may break th
264
265 The configuration option CONFIG_SCSI_NCR53C8XX
266 driver to use normal I/O in all cases.
267
268
269 5. Tagged command queueing
270 ==========================
271
272 Queuing more than 1 command at a time to a dev
273 optimizations based on actual head positions a
274 characteristics. This feature may also reduce
275 In order to really gain advantage of this feat
276 a reasonable cache size (No miracle is to be e
277 hard disk with 128 KB or less).
278 Some known SCSI devices do not properly suppor
279 Generally, firmware revisions that fix this ki
280 at respective vendor web/ftp sites.
281 All I can say is that the hard disks I use on
282 this driver with tagged command queuing enable
283
284 - IBM S12 0662
285 - Conner 1080S
286 - Quantum Atlas I
287 - Quantum Atlas II
288
289 If your controller has NVRAM, you can configur
290 from the user setup tool. The Tekram Setup pro
291 maximum number of queued commands up to 32. Th
292 to enable or disable this feature.
293
294 The maximum number of simultaneous tagged comm
295 is currently set to 8 by default. This value
296 disks. With large SCSI disks (>= 2GB, cache >
297 <= 10 ms), using a larger value may give bette
298
299 The sym53c8xx driver supports up to 255 comman
300 generic ncr53c8xx driver supports up to 64, bu
301 generally not worth-while, unless you are usin
302 array. It is noticeable that most of recent ha
303 more than 64 simultaneous commands. So, using
304 is probably just resource wasting.
305
306 If your controller does not have NVRAM or if i
307 BIOS/SETUP, you can configure tagged queueing
308 depths from the boot command-line. For example
309
310 ncr53c8xx=tags:4/t2t3q15-t4q7/t1u0q32
311
312 will set tagged commands queue depths as follo
313
314 - target 2 all luns on controller 0 --> 15
315 - target 3 all luns on controller 0 --> 15
316 - target 4 all luns on controller 0 --> 7
317 - target 1 lun 0 on controller 1 --> 32
318 - all other target/lun --> 4
319
320 In some special conditions, some SCSI disk fir
321 QUEUE FULL status for a SCSI command. This beh
322 driver using the following heuristic:
323
324 - Each time a QUEUE FULL status is returned, t
325 to the actual number of disconnected command
326
327 - Every 1000 successfully completed SCSI comma
328 current limit, the maximum number of queueab
329
330 Since QUEUE FULL status reception and handling
331 driver notifies by default this problem to use
332 number of commands used and their status, as w
333 device queue depth change.
334 The heuristic used by the driver in handling Q
335 impact on performances is not too bad. You can
336 setting verbose level to zero, as follow:
337
338 1st method:
339 boot your system using 'ncr53c8xx=
340
341 2nd method:
342 apply "setverbose 0" control comma
343 corresponding to your controller a
344
345 6. Parity checking
346 ==================
347
348 The driver supports SCSI parity checking and P
349 checking. These features must be enabled in o
350 transfers. However, some flawed devices or mo
351 problems with parity. You can disable either P
352 checking by entering appropriate options from
353 (See 10: Boot setup commands).
354
355 7. Profiling information
356 ========================
357
358 Profiling information is available through the
359 Since gathering profiling information may impa
360 feature is disabled by default and requires a
361 option to be set to Y.
362
363 The device associated with a host has the foll
364
365 /proc/scsi/ncr53c8xx/N (N=0,1,2
366
367 Generally, only 1 board is used on hardware co
368
369 /proc/scsi/ncr53c8xx/0
370
371 However, if the driver has been made as module
372 hosts is incremented each time the driver is l
373
374 In order to display profiling information, jus
375
376 cat /proc/scsi/ncr53c8xx/0
377
378 and you will get something like the following
379
380 General information:
381 Chip NCR53C810, device id 0x1, revision id
382 IO port address 0x6000, IRQ number 10
383 Using memory mapped IO at virtual address
384 Synchronous transfer period 25, max comman
385 Profiling information:
386 num_trans = 18014
387 num_kbytes = 671314
388 num_disc = 25763
389 num_break = 1673
390 num_int = 1685
391 num_fly = 18038
392 ms_setup = 4940
393 ms_data = 369940
394 ms_disc = 183090
395 ms_post = 1320
396
397 General information is easy to understand. The
398 revision ID identify the SCSI chip as follows:
399
400 ======= ============= ===========
401 Chip Device id Revision Id
402 ======= ============= ===========
403 810 0x1 < 0x10
404 810A 0x1 >= 0x10
405 815 0x4
406 825 0x3 < 0x10
407 860 0x6
408 825A 0x3 >= 0x10
409 875 0xf
410 895 0xc
411 ======= ============= ===========
412
413 The profiling information is updated upon comp
414 A data structure is allocated and zeroed when
415 attached. So, if the driver is a module, the p
416 cleared each time the driver is loaded. The "
417 allows you to clear these counters at any time
418
419 The following counters are available:
420
421 ("num" prefix means "number of",
422 "ms" means milli-seconds)
423
424 num_trans
425 Number of completed commands
426 Example above: 18014 completed command
427
428 num_kbytes
429 Number of kbytes transferred
430 Example above: 671 MB transferred
431
432 num_disc
433 Number of SCSI disconnections
434 Example above: 25763 SCSI disconnectio
435
436 num_break
437 number of script interruptions (phase
438 Example above: 1673 script interruptio
439
440 num_int
441 Number of interrupts other than "on th
442 Example above: 1685 interruptions not
443
444 num_fly
445 Number of interrupts "on the fly"
446 Example above: 18038 interruptions "on
447
448 ms_setup
449 Elapsed time for SCSI commands setups
450 Example above: 4.94 seconds
451
452 ms_data
453 Elapsed time for data transfers
454 Example above: 369.94 seconds spent fo
455
456 ms_disc
457 Elapsed time for SCSI disconnections
458 Example above: 183.09 seconds spent di
459
460 ms_post
461 Elapsed time for command post processi
462 (time from SCSI status get to command
463 Example above: 1.32 seconds spent for
464
465 Due to the 1/100 second tick of the system clo
466 be wrong.
467
468 In the example above, we got 18038 interrupts
469 1673 script breaks generally due to disconnect
470 of the scatter list.
471
472
473 8. Control commands
474 ===================
475
476 Control commands can be sent to the driver wit
477 the proc SCSI file system. The generic command
478 following::
479
480 echo "<verb> <parameters>" >/proc/scsi/n
481 (assumes controller number is 0)
482
483 Using "all" for "<target>" parameter with the
484 apply to all targets of the SCSI chain (except
485
486 Available commands:
487
488 8.1 Set minimum synchronous period factor
489 -----------------------------------------
490
491 setsync <target> <period factor>
492
493 :target: target number
494 :period: minimum synchronous period.
495 Maximum speed = 1000/(4*period
496 cases below.
497
498 Specify a period of 255, to force asynchro
499
500 - 10 means 25 nano-seconds synchronous p
501 - 11 means 30 nano-seconds synchronous p
502 - 12 means 50 nano-seconds synchronous p
503
504 8.2 Set wide size
505 -----------------
506
507 setwide <target> <size>
508
509 :target: target number
510 :size: 0=8 bits, 1=16bits
511
512 8.3 Set maximum number of concurrent tagged co
513 ----------------------------------------------
514
515 settags <target> <tags>
516
517 :target: target number
518 :tags: number of concurrent tagged com
519 must not be greater than SCSI_N
520
521 8.4 Set order type for tagged command
522 -------------------------------------
523
524 setorder <order>
525
526 :order: 3 possible values:
527
528 simple:
529 use SIMPLE TAG for all
530
531 ordered:
532 use ORDERED TAG for al
533
534 default:
535 use default tag type,
536 SIMPLE TAG for read
537 ORDERED TAG for write
538
539
540 8.5 Set debug mode
541 ------------------
542
543 setdebug <list of debug flags>
544
545 Available debug flags:
546
547 ======== =============================
548 alloc print info about memory alloc
549 queue print info about insertions i
550 result print sense data on CHECK CON
551 scatter print info about the scatter
552 scripts print info about the script b
553 tiny print minimal debugging infor
554 timing print timing information of t
555 nego print information about SCSI
556 phase print information on script i
557 ======== =============================
558
559 Use "setdebug" with no argument to reset d
560
561
562 8.6 Clear profile counters
563 --------------------------
564
565 clearprof
566
567 The profile counters are automatically cle
568 data transferred reaches 1000 GB in order
569 The "clearprof" command allows you to clea
570
571
572 8.7 Set flag (no_disc)
573 ----------------------
574
575 setflag <target> <flag>
576
577 target: target number
578
579 For the moment, only one flag is available
580
581 no_disc: not allow target to disconn
582
583 Do not specify any flag in order to reset
584
585 setflag 4
586 will reset no_disc flag for target 4, so
587
588 setflag all
589 will allow disconnection for all devices
590
591
592 8.8 Set verbose level
593 ---------------------
594
595 setverbose #level
596
597 The driver default verbose level is 1. Thi
598 th driver verbose level after boot-up.
599
600 8.9 Reset all logical units of a target
601 ---------------------------------------
602
603 resetdev <target>
604
605 :target: target number
606
607 The driver will try to send a BUS DEVICE R
608 (Only supported by the SYM53C8XX driver an
609
610 8.10 Abort all tasks of all logical units of a
611 ----------------------------------------------
612
613 cleardev <target>
614
615 :target: target number
616
617 The driver will try to send a ABORT messag
618 of the target.
619
620 (Only supported by the SYM53C8XX driver an
621
622
623 9. Configuration parameters
624 ===========================
625
626 If the firmware of all your devices is perfect
627 features supported by the driver can be enable
628 if only one has a flaw for some SCSI feature,
629 support by the driver of this feature at linux
630 this feature after boot-up only for devices th
631
632 CONFIG_SCSI_NCR53C8XX_IOMAPPED (default
633 Answer "y" if you suspect your mother boar
634
635 May slow down performance a little. This
636 Linux/PPC and is used no matter what you s
637 suffers no performance loss with this opti
638 mapped anyway.
639
640 CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS (default
641 Default tagged command queue depth.
642
643 CONFIG_SCSI_NCR53C8XX_MAX_TAGS (defaul
644 This option allows you to specify the maxi
645 that can be queued to a device. The maximu
646
647 CONFIG_SCSI_NCR53C8XX_SYNC (default
648 This option allows you to specify the freq
649 will use at boot time for synchronous data
650 This frequency can be changed later with t
651 0 means "asynchronous data transfers".
652
653 CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO (default
654 Force synchronous negotiation for all SCSI
655
656 Some SCSI-2 devices do not report this fea
657 response but do support it properly (TAMAR
658
659 CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT (default
660 If you suspect a device of yours does not
661 you can answer "y". Then, all SCSI devices
662 even while performing long SCSI operations
663
664 CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT
665 Genuine SYMBIOS boards use GPIO0 in output
666 bit as a flag indicating singled-ended/dif
667 If all the boards of your system are genui
668 BIOS and drivers from SYMBIOS, you would w
669
670 This option must NOT be enabled if your sy
671 based scsi board with a vendor-specific BI
672 For example, Tekram DC-390/U, DC-390/W and
673 use a vendor-specific BIOS and are known t
674 GPIO wiring. So, this option must not be e
675 such a board installed.
676
677 CONFIG_SCSI_NCR53C8XX_NVRAM_DETECT
678 Enable support for reading the serial NVRA
679 some Symbios compatible cards, and Tekram
680 systems with more than one Symbios compati
681 one has a serial NVRAM, or for a system wi
682 Tekram cards. Enables setting the boot ord
683 to something other than the default order
684 Also enables Symbios and Tekram cards to b
685 CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT may b
686 mixture of Symbios and Tekram cards so the
687 the full range of Symbios features, differ
688 causing problems for the Tekram card(s).
689
690 10. Boot setup commands
691 =======================
692
693 10.1 Syntax
694 -----------
695
696 Setup commands can be passed to the driver eit
697 string variable using 'insmod'.
698
699 A boot setup command for the ncr53c8xx (sym53c
700 driver name "ncr53c8xx="(sym53c8xx). The kerne
701 an optional list of integers separated with co
702 list of comma-separated strings. Example of bo
703 prompt::
704
705 lilo: linux root=/dev/hda2 ncr53c8xx=tags:
706
707 - enable tagged commands, up to 4 tagged comma
708 - set synchronous negotiation speed to 10 Mega
709 - set DEBUG_NEGO flag.
710
711 Since comma seems not to be allowed when defin
712 'insmod', the driver also accepts <space> as o
713 The following command will install driver modu
714 above::
715
716 insmod ncr53c8xx.o ncr53c8xx="tags:4 sync:
717
718 For the moment, the integer list of arguments
719 It will be used in the future in order to allo
720
721 Each string argument must be specified as "key
722 characters and digits are allowed.
723
724 In a system that contains multiple 53C8xx adap
725 specified driver on each adapter. To exclude a
726
727 The sequence of commands::
728
729 insmod sym53c8xx sym53c8xx=excl:0x1400
730 insmod ncr53c8xx
731
732 installs the sym53c8xx driver on all adapters
733 address 0x1400 and then installs the ncr53c8xx
734 port address 0x1400.
735
736
737 10.2 Available arguments
738 ------------------------
739
740 10.2.1 Master parity checking
741 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
742
743 ====== ========
744 mpar:y enabled
745 mpar:n disabled
746 ====== ========
747
748 10.2.2 Scsi parity checking
749 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^
750
751 ====== ========
752 spar:y enabled
753 spar:n disabled
754 ====== ========
755
756 10.2.3 Scsi disconnections
757 ^^^^^^^^^^^^^^^^^^^^^^^^^^^
758
759 ====== ========
760 disc:y enabled
761 disc:n disabled
762 ====== ========
763
764 10.2.4 Special features
765 ^^^^^^^^^^^^^^^^^^^^^^^^
766
767 Only apply to 810A, 825A, 860, 875 and 895
768 Have no effect with other ones.
769
770 ======= ===========================
771 specf:y (or 1) enabled
772 specf:n (or 0) disabled
773 specf:3 enabled except Memor
774 ======= ===========================
775
776 The default driver setup is 'specf:3'. As a
777 must be specified in the boot setup command
778 Invalidate.
779
780 10.2.5 Ultra SCSI support
781 ^^^^^^^^^^^^^^^^^^^^^^^^^^
782
783 Only apply to 860, 875, 895, 895a, 896, 101
784 Have no effect with other ones.
785
786 ======= ========================
787 ultra:n All ultra speeds enabled
788 ultra:2 Ultra2 enabled
789 ultra:1 Ultra enabled
790 ultra:0 Ultra speeds disabled
791 ======= ========================
792
793 10.2.6 Default number of tagged commands
794 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
795
796 ======================= ==============
797 tags:0 (or tags:1 ) tagged command
798 tags:#tags (#tags > 1) tagged command
799 ======================= ==============
800
801 #tags will be truncated to the max queued co
802 This option also allows to specify a command
803 that support tagged command queueing.
804
805 Example::
806
807 ncr53c8xx=tags:10/t2t3q16-t5q24/t1u2q32
808
809 will set devices queue depth as follow:
810
811 - controller #0 target #2 and target #3
812 - controller #0 target #5
813 - controller #1 target #1 logical unit #
814 - all other logical units (all targets,
815
816 10.2.7 Default synchronous period factor
817 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
818
819 ============ =================================
820 sync:255 disabled (asynchronous transfer m
821 sync:#factor
822 ============ ================
823 #factor = 10 Ultra-2 SCSI 40
824 #factor = 11 Ultra-2 SCSI 33
825 #factor < 25 Ultra SCSI 20
826 #factor < 50 Fast SCSI-2
827 ============ ================
828 ============ =================================
829
830 In all cases, the driver will use the minimu
831 controllers according to NCR53C8XX chip type
832
833 10.2.8 Negotiate synchronous with all devices
834 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
835 (force sync nego)
836
837 ===== =========
838 fsn:y enabled
839 fsn:n disabled
840 ===== =========
841
842 10.2.9 Verbosity level
843 ^^^^^^^^^^^^^^^^^^^^^^^
844
845 ====== =========
846 verb:0 minimal
847 verb:1 normal
848 verb:2 too much
849 ====== =========
850
851 10.2.10 Debug mode
852 ^^^^^^^^^^^^^^^^^^
853
854 ======== ===================================
855 debug:0 clear debug flags
856 debug:#x set debug flags
857
858 #x is an integer value combining t
859
860 ============= ======
861 DEBUG_ALLOC 0x1
862 DEBUG_PHASE 0x2
863 DEBUG_POLL 0x4
864 DEBUG_QUEUE 0x8
865 DEBUG_RESULT 0x10
866 DEBUG_SCATTER 0x20
867 DEBUG_SCRIPT 0x40
868 DEBUG_TINY 0x80
869 DEBUG_TIMING 0x100
870 DEBUG_NEGO 0x200
871 DEBUG_TAGS 0x400
872 DEBUG_FREEZE 0x800
873 DEBUG_RESTART 0x1000
874 ============= ======
875 ======== ===================================
876
877 You can play safely with DEBUG_NEGO. However
878 generate bunches of syslog messages.
879
880 10.2.11 Burst max
881 ^^^^^^^^^^^^^^^^^
882
883 ========= ===================================
884 burst:0 burst disabled
885 burst:255 get burst length from initial IO re
886 burst:#x burst enabled (1<<#x burst transfer
887
888 #x is an integer value which is log
889 max.
890
891 The NCR53C875 and NCR53C825A suppor
892 (#x = 7).
893
894 Other chips only support up to 16 (
895
896 This is a maximum value. The driver
897 to chip and revision ids. By defaul
898 value supported by the chip.
899 ========= ===================================
900
901 10.2.12 LED support
902 ^^^^^^^^^^^^^^^^^^^
903
904 ===== ===================
905 led:1 enable LED support
906 led:0 disable LED support
907 ===== ===================
908
909 Do not enable LED support if your scsi board
910 (See 'Configuration parameters')
911
912 10.2.13 Max wide
913 ^^^^^^^^^^^^^^^^
914
915 ====== ===================
916 wide:1 wide scsi enabled
917 wide:0 wide scsi disabled
918 ====== ===================
919
920 Some scsi boards use a 875 (ultra wide) and
921 If you have connected a wide device with a 5
922 converter, any accepted wide negotiation wil
923 In such a case, using "wide:0" in the bootup
924
925 10.2.14 Differential mode
926 ^^^^^^^^^^^^^^^^^^^^^^^^^
927
928 ====== ==============================
929 diff:0 never set up diff mode
930 diff:1 set up diff mode if BIOS set i
931 diff:2 always set up diff mode
932 diff:3 set diff mode if GPIO3 is not
933 ====== ==============================
934
935 10.2.15 IRQ mode
936 ^^^^^^^^^^^^^^^^
937
938 ========= ===========================
939 irqm:0 always open drain
940 irqm:1 same as initial settings (a
941 irqm:2 always totem pole
942 irqm:0x10 driver will not use IRQF_SH
943 ========= ===========================
944
945 (Bits 0x10 and 0x20 can be combined with h
946
947 10.2.16 Reverse probe
948 ^^^^^^^^^^^^^^^^^^^^^
949
950 ========= ==========================
951 revprob:n probe chip ids from the PC
952 810, 815, 820, 860, 875, 8
953 revprob:y probe chip ids in the reve
954 ========= ==========================
955
956 10.2.17 Fix up PCI configuration space
957 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
958 pcifix:<option bits>
959
960 Available option bits:
961
962 === ===============================
963 0x0 No attempt to fix PCI configura
964 0x1 Set PCI cache-line size registe
965 0x2 Set write and invalidate bit in
966 0x4 Increase if necessary PCI laten
967 === ===============================
968
969 Use 'pcifix:7' in order to allow the drive
970
971 10.2.18 Serial NVRAM
972 ^^^^^^^^^^^^^^^^^^^^
973
974 ======= ==========================
975 nvram:n do not look for serial NVR
976 nvram:y test controllers for onboa
977 ======= ==========================
978
979 (alternate binary form)
980 mvram=<bits options>
981
982 ==== ===============================
983 0x01 look for NVRAM (equivalent to
984 0x02 ignore NVRAM "Synchronous negot
985 0x04 ignore NVRAM "Wide negotiation"
986 0x08 ignore NVRAM "Scan at boot time
987 0x80 also attach controllers set to
988 ==== ===============================
989
990 10.2.19 Check SCSI BUS
991 ^^^^^^^^^^^^^^^^^^^^^^
992
993 buschk:<option bits>
994
995 Available option bits:
996
997 ==== ===============================
998 0x0: No check.
999 0x1: Check and do not attach the con
1000 0x2: Check and just warn on error.
1001 0x4: Disable SCSI bus integrity che
1002 ==== ==============================
1003
1004 10.2.20 Exclude a host from being attached
1005 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1006
1007 excl=<io_address>
1008
1009 Prevent host at a given io address from b
1010 For example 'ncr53c8xx=excl:0xb400,excl:0
1011 ncr53c8xx driver not to attach hosts at a
1012
1013 10.2.21 Suggest a default SCSI id for hosts
1014 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1015
1016 ========== =====================
1017 hostid:255 no id suggested.
1018 hostid:#x (0 < x < 7) x suggest
1019 ========== =====================
1020
1021 If a host SCSI id is available from the N
1022 any value suggested as boot option. Other
1023 different from 255 has been supplied, it
1024 try to deduce the value previously set in
1025 7 if the hardware value is zero.
1026
1027 10.2.22 Enable use of IMMEDIATE ARBITRATION
1028 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1029
1030 (only supported by the sym53c8xx driv
1031
1032 ======= ===================================
1033 iarb:0 do not use this feature.
1034 iarb:#x use this feature according to bit f
1035
1036 ========= =========================
1037 bit 0 (1) enable IARB each time the
1038 when it arbitrated for th
1039 (#x >> 4) maximum number of success
1040 initiator win arbitration
1041 to send to a device.
1042 ========= =========================
1043 ======= ===================================
1044
1045 Boot fail safe
1046 safe:y load the following assumed fa
1047
1048 ======================== =============
1049 master parity disabled
1050 scsi parity enabled
1051 disconnections not allowed
1052 special features disabled
1053 ultra scsi disabled
1054 force sync negotiation disabled
1055 reverse probe disabled
1056 PCI fix up disabled
1057 serial NVRAM enabled
1058 verbosity level 2
1059 tagged command queuing disabled
1060 synchronous negotiation disabled
1061 debug flags none
1062 burst length from BIOS set
1063 LED support disabled
1064 wide support disabled
1065 settle time 10 seconds
1066 differential support from BIOS set
1067 irq mode from BIOS set
1068 SCSI BUS check do not attach
1069 immediate arbitration disabled
1070 ======================== =============
1071
1072 10.3 Advised boot setup commands
1073 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1074
1075 If the driver has been configured with defaul
1076 boot setup is::
1077
1078 ncr53c8xx=mpar:y,spar:y,disc:y,specf:3,fsn
1079 tags:0,sync:50,debug:0,burst:7,l
1080
1081 For an installation diskette or a safe but no
1082 boot setup can be::
1083
1084 ncr53c8xx=safe:y,mpar:y,disc:y
1085 ncr53c8xx=safe:y,disc:y
1086 ncr53c8xx=safe:y,mpar:y
1087 ncr53c8xx=safe:y
1088
1089 My personal system works flawlessly with the
1090
1091 ncr53c8xx=mpar:y,spar:y,disc:y,specf:1,fsn
1092 tags:32,sync:12,debug:0,burst:7,
1093
1094 The driver prints its actual setup when verbo
1095 "ncr53c8xx=verb:2" to get the "static" setup
1096 to your boot setup command in order to check
1097 using.
1098
1099 10.4 PCI configuration fix-up boot option
1100 -----------------------------------------
1101
1102 pcifix:<option bits>
1103
1104 Available option bits:
1105
1106 === ================================
1107 0x1 Set PCI cache-line size register
1108 0x2 Set write and invalidate bit in
1109 === ================================
1110
1111 Use 'pcifix:3' in order to allow the driver t
1112
1113 These options only apply to new SYMBIOS chips
1114 and 895 and are only supported for Pentium an
1115 Recent SYMBIOS 53C8XX scsi processors are abl
1116 and PCI write and invalidate commands. These
1117 cache line size register to be properly set i
1118 space of the chips. On the other hand, chips
1119 invalidate commands only if the corresponding
1120 PCI command register.
1121
1122 Not all PCI bioses set the PCI cache line reg
1123 invalidate bit in the PCI configuration space
1124 Optimized PCI accesses may be broken for some
1125 make problems with some PCI boards.
1126
1127 This fix-up worked flawlessly on my previous
1128 (MB Triton HX / 53C875 / 53C810A)
1129 I use these options at my own risks as you wi
1130 use them too.
1131
1132
1133 10.5 Serial NVRAM support boot option
1134 -------------------------------------
1135
1136 ======= =================================
1137 nvram:n do not look for serial NVRAM
1138 nvram:y test controllers for onboard seri
1139 ======= =================================
1140
1141 This option can also been entered as an hexad
1142 to control what information the driver will g
1143 information it will ignore.
1144 For details see '17. Serial NVRAM support'.
1145
1146 When this option is enabled, the driver tries
1147 a Serial NVRAM. This memory is used to hold u
1148
1149 The parameters the driver is able to get from
1150 data format used, as follow:
1151
1152 +-------------------------------+------------
1153 | |Tekram forma
1154 +-------------------------------+------------
1155 |General and host parameters |
1156 +-------------------------------+------------
1157 | * Boot order | N
1158 +-------------------------------+------------
1159 | * Host SCSI ID | Y
1160 +-------------------------------+------------
1161 | * SCSI parity checking | Y
1162 +-------------------------------+------------
1163 | * Verbose boot messages | N
1164 +-------------------------------+------------
1165 |SCSI devices parameters
1166 +-------------------------------+------------
1167 | * Synchronous transfer speed | Y
1168 +-------------------------------+------------
1169 | * Wide 16 / Narrow | Y
1170 +-------------------------------+------------
1171 | * Tagged Command Queuing | Y
1172 | enabled |
1173 +-------------------------------+------------
1174 | * Disconnections enabled | Y
1175 +-------------------------------+------------
1176 | * Scan at boot time | N
1177 +-------------------------------+------------
1178
1179 In order to speed up the system boot, for eac
1180 the "scan at boot time" option, the driver fo
1181 first TEST UNIT READY command received for th
1182
1183 Some SDMS BIOS revisions seem to be unable to
1184 hard disks. In such a situation you cannot co
1185 optimized parameters value.
1186
1187 The 'nvram' boot option can be entered in hex
1188 to ignore some options configured in the NVRA
1189
1190 mvram=<bits options>
1191
1192 ==== ================================
1193 0x01 look for NVRAM (equivalent to n
1194 0x02 ignore NVRAM "Synchronous negoti
1195 0x04 ignore NVRAM "Wide negotiation"
1196 0x08 ignore NVRAM "Scan at boot time"
1197 0x80 also attach controllers set to O
1198 ==== ================================
1199
1200 Option 0x80 is only supported by the sym53c8x
1201 default. Result is that, by default (option n
1202 will not attach controllers set to OFF in the
1203
1204 The ncr53c8xx always tries to attach all the
1205 not been added to the ncr53c8xx driver, since
1206 confuse users who use this driver since a lon
1207 controller not to be attached by the ncr53c8x
1208 must use the 'excl' driver boot option.
1209
1210 10.6 SCSI BUS checking boot option.
1211 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1212
1213 When this option is set to a non-zero value,
1214 logic state, 100 micro-seconds after having a
1215 The driver just reads SCSI lines and checks a
1216 Since SCSI devices shall release the BUS at m
1217 RESET has been asserted, any signal to TRUE m
1218 Unfortunately, the following common SCSI BUS
1219
1220 - Only 1 terminator installed.
1221 - Misplaced terminators.
1222 - Bad quality terminators.
1223
1224 On the other hand, either bad cabling, broken
1225 devices, ... may cause a SCSI signal to be wr
1226
1227 10.7 IMMEDIATE ARBITRATION boot option
1228 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1229
1230 This option is only supported by the SYM53C8X
1231
1232 SYMBIOS 53C8XX chips are able to arbitrate fo
1233 have detected an expected disconnection (BUS
1234 to be started, bit 1 of SCNTL1 IO register mu
1235 connected to the SCSI BUS.
1236
1237 When this feature has been enabled for the cu
1238 every chance to win arbitration if only devic
1239 competing for the SCSI BUS. By the way, when
1240 then it will for sure win the next SCSI BUS a
1241
1242 Since, there is no way to know what devices a
1243 BUS, using this feature can be extremely unfa
1244 to enable it, or at most enable this feature
1245 the previous arbitration (boot option 'iarb:1
1246
1247 This feature has the following advantages:
1248
1249 a) Allow the initiator with ID 7 to win arbit
1250 b) Overlap at least 4 micro-seconds of arbitr
1251 of SCRIPTS that deal with the end of the c
1252 starts the next job.
1253
1254 Hmmm... But (a) may just prevent other device
1255 and delay data transfers or status/completion
1256 SCSI BUS bandwidth if the SCRIPTS execution l
1257
1258 The use of IARB needs the SCSI_NCR_IARB_SUPPO
1259 at compile time and the 'iarb' boot option to
1260 value at boot time. It is not that useful for
1261 to stress SCSI devices or for some applicatio
1262 it. By the way, if you experience badnesses l
1263 'bad reselections', etc... when using IARB on
1264 be surprised, because force-feeding anything
1265 same time cannot work for a long time. :-))
1266
1267
1268 11. Some constants and flags of the ncr53c8xx
1269 =============================================
1270
1271 Some of these are defined from the configurat
1272 change other "defines", you must edit the hea
1273 if you know what you are doing.
1274
1275 SCSI_NCR_SETUP_SPECIAL_FEATURES (default: def
1276 If defined, the driver will enable so
1277 to chip and revision id.
1278
1279 For 810A, 860, 825A, 875 and 895 scsi
1280 support of features that reduce load
1281 during scsi transfer processing: bur
1282 read line, prefetch, cache line, writ
1283 burst 128 (875 only), large dma fifo
1284 Can be changed by the following boot
1285
1286 ncr53c8xx=specf:n
1287
1288 SCSI_NCR_IOMAPPED (default: not
1289 If defined, normal I/O is forced.
1290
1291 SCSI_NCR_SHARE_IRQ (default: def
1292 If defined, request shared IRQ.
1293
1294 SCSI_NCR_MAX_TAGS (default: 8)
1295 Maximum number of simultaneous tagged
1296
1297 Can be changed by "settags <target> <
1298
1299 SCSI_NCR_SETUP_DEFAULT_SYNC (default: 50)
1300 Transfer period factor the driver wil
1301 negotiation. 0 means asynchronous.
1302
1303 Can be changed by "setsync <target> <
1304
1305 SCSI_NCR_SETUP_DEFAULT_TAGS (default: 8)
1306 Default number of simultaneous tagged
1307
1308 < 1 means tagged command queuing disa
1309
1310 SCSI_NCR_ALWAYS_SIMPLE_TAG (default: def
1311 Use SIMPLE TAG for read and write com
1312
1313 Can be changed by "setorder <ordered|
1314
1315 SCSI_NCR_SETUP_DISCONNECTION (default: def
1316 If defined, targets are allowed to di
1317
1318 SCSI_NCR_SETUP_FORCE_SYNC_NEGO (default: not
1319 If defined, synchronous negotiation i
1320
1321 Can be changed by "setsync <target> <
1322
1323 SCSI_NCR_SETUP_MASTER_PARITY (default: def
1324 If defined, master parity checking is
1325
1326 SCSI_NCR_SETUP_SCSI_PARITY (default: def
1327 If defined, SCSI parity checking is e
1328
1329 SCSI_NCR_PROFILE_SUPPORT (default: not
1330 If defined, profiling information is
1331
1332 SCSI_NCR_MAX_SCATTER (default: 128
1333 Scatter list size of the driver ccb.
1334
1335 SCSI_NCR_MAX_TARGET (default: 16)
1336 Max number of targets per host.
1337
1338 SCSI_NCR_MAX_HOST (default: 2)
1339 Max number of host controllers.
1340
1341 SCSI_NCR_SETTLE_TIME (default: 2)
1342 Number of seconds the driver will wai
1343
1344 SCSI_NCR_TIMEOUT_ALERT (default: 3)
1345 If a pending command will time out af
1346 an ordered tag is used for the next c
1347
1348 Avoids timeouts for unordered tagged
1349
1350 SCSI_NCR_CAN_QUEUE (default: 7*S
1351 Max number of commands that can be qu
1352
1353 SCSI_NCR_CMD_PER_LUN (default: SCS
1354 Max number of commands queued to a ho
1355
1356 SCSI_NCR_SG_TABLESIZE (default: SCS
1357 Max size of the Linux scatter/gather
1358
1359 SCSI_NCR_MAX_LUN (default: 8)
1360 Max number of LUNs per target.
1361
1362
1363 12. Installation
1364 ================
1365
1366 This driver is part of the linux kernel distr
1367 Driver files are located in the sub-directory
1368 kernel source tree.
1369
1370 Driver files::
1371
1372 README.ncr53c8xx : this file
1373 ChangeLog.ncr53c8xx : change log
1374 ncr53c8xx.h : definitions
1375 ncr53c8xx.c : the driver
1376
1377 New driver versions are made available separa
1378 changes and new features prior to including t
1379 distribution. The following URL provides info
1380 patches:
1381
1382 ftp://ftp.tux.org/pub/people/gerard-rou
1383
1384
1385 13. Architecture dependent features
1386 ===================================
1387
1388 <Not yet written>
1389
1390
1391 14. Known problems
1392 ==================
1393
1394 14.1 Tagged commands with Iomega Jaz device
1395 -------------------------------------------
1396
1397 I have not tried this device, however it has
1398 following: This device is capable of Tagged c
1399 while spinning up, it rejects Tagged commands
1400 conforms to 6.8.2 of SCSI-2 specifications. T
1401 the driver in that situation is not satisfyin
1402 Tagged command queuing for devices that are a
1403 other problem that may appear is timeouts. Th
1404 timeouts seems to edit linux/drivers/scsi/sd.
1405 current timeout values.
1406
1407 14.2 Device names change when another control
1408 ---------------------------------------------
1409
1410 When you add a new NCR53C8XX chip based contr
1411 has one or more controllers of this family, i
1412 the driver registers them to the kernel cause
1413 name changes.
1414 When at least one controller uses NvRAM, SDMS
1415 define the order the BIOS will scan the scsi
1416 controllers according to BIOS information if
1417
1418 If your controllers do not have NvRAM, you ca
1419
1420 - Ask the driver to probe chip ids in reverse
1421 line: ncr53c8xx=revprob:y
1422 - Make appropriate changes in the fstab.
1423 - Use the 'scsidev' tool from Eric Youngdale.
1424
1425 14.3 Using only 8 bit devices with a WIDE SCS
1426 ---------------------------------------------
1427
1428 When only 8 bit NARROW devices are connected
1429 you must ensure that lines of the wide part o
1430 This can be achieved by ENABLING the WIDE TER
1431 controller card.
1432
1433 The TYAN 1365 documentation revision 1.2 is n
1434 (page 10, figure 3.3).
1435
1436 14.4 Possible data corruption during a Memory
1437 ---------------------------------------------
1438
1439 This problem is described in SYMBIOS DEL 397,
1440
1441 In some complex situations, 53C875 chips revi
1442 Write and Invalidate Command at a not cache-l
1443 This is only possible when Cache Line Size is
1444 Pentium systems use a 8 DWORDS cache line siz
1445 this chip bug, unlike i486 systems that use a
1446
1447 When this situation occurs, the chip may comp
1448 command after having only filled part of the
1449 the transfer, leaving to data corruption the
1450
1451 Not using Write And Invalidate obviously gets
1452 it is now the default setting of the driver.
1453 However, for people like me who want to enabl
1454 part of a work-around suggested by SYMBIOS. T
1455 addressing logic when the DATA IN phase is en
1456 from being triggered for the first SCSI MOVE
1457 should be enough according to the following:
1458
1459 The only driver internal data structure that
1460 that is moved by the SCRIPTS processor is the
1461 the context of the SCSI transfer. This data s
1462 boundary (Pentium Cache Line Size), and so is
1463 least on Pentium systems.
1464
1465 But the conditions of this bug can be met whe
1466 performed using a buffer that is 4 DWORDS but
1467 This cannot happen under Linux when scatter/g
1468 they only refer to system buffers that are we
1469 may only be needed under Linux when a scatter
1470 when the SCSI DATA IN phase is reentered afte
1471
1472 15. SCSI problem troubleshooting
1473 ================================
1474
1475 15.1 Problem tracking
1476 ---------------------
1477
1478 Most SCSI problems are due to a non conforman
1479 devices. If unfortunately you have SCSI prob
1480 following things:
1481
1482 - SCSI bus cables
1483 - terminations at both end of the SCSI chain
1484 - linux syslog messages (some of them may hel
1485
1486 If you do not find the source of problems, yo
1487 driver with no features enabled.
1488
1489 - only asynchronous data transfers
1490 - tagged commands disabled
1491 - disconnections not allowed
1492
1493 Now, if your SCSI bus is ok, your system have
1494 with this safe configuration but performances
1495
1496 If it still fails, then you can send your pro
1497 appropriate mailing lists or news-groups. Se
1498 be sure I will receive it. Obviously, a bug
1499 possible.
1500
1501 My email address: Gerard Roudier <groudie
1502
1503 Allowing disconnections is important if you u
1504 your SCSI bus but often causes problems with
1505 Synchronous data transfers increases throughp
1506 hard disks. Good SCSI hard disks with a larg
1507 tagged commands queuing.
1508
1509 Try to enable one feature at a time with cont
1510
1511 ::
1512
1513 echo "setsync all 25" >/proc/scsi/ncr53c8
1514
1515 Will enable fast synchronous data transfer ne
1516
1517 ::
1518
1519 echo "setflag 3" >/proc/scsi/ncr53c8xx/0
1520
1521 Will reset flags (no_disc) for target 3, and
1522 the SCSI Bus.
1523
1524 ::
1525
1526 echo "settags 3 8" >/proc/scsi/ncr53c8xx/
1527
1528 Will enable tagged command queuing for target
1529
1530 Once you have found the device and the featur
1531 disable that feature for that device.
1532
1533 15.2 Understanding hardware error reports
1534 -----------------------------------------
1535
1536 When the driver detects an unexpected error c
1537 message of the following pattern::
1538
1539 sym53c876-0:1: ERROR (0:48) (1-21-65) (f/
1540 sym53c876-0: script cmd = 19000000
1541 sym53c876-0: regdump: da 10 80 95 47 0f 0
1542
1543 Some fields in such a message may help you un
1544 problem, as follows::
1545
1546 sym53c876-0:1: ERROR (0:48) (1-21-65) (f/
1547 ............A.........B.C....D.E..F....G.
1548
1549 Field A : target number.
1550 SCSI ID of the device the controller was ta
1551 error occurs.
1552
1553 Field B : DSTAT io register (DMA STATUS)
1554 ======== ================================
1555 Bit 0x40 MDPE Master Data Parity Error
1556 Data parity error detected on th
1557 Bit 0x20 BF Bus Fault
1558 PCI bus fault condition detected
1559 Bit 0x01 IID Illegal Instruction Detecte
1560 Set by the chip when it detects
1561 on some condition that makes an
1562 Bit 0x80 DFE Dma Fifo Empty
1563 Pure status bit that does not in
1564 ======== ================================
1565
1566 If the reported DSTAT value contains a comb
1567 BF (0x20), then the cause may be likely due
1568
1569 Field C : SIST io register (SCSI Interrupt St
1570 ======== ================================
1571 Bit 0x08 SGE SCSI GROSS ERROR
1572 Indicates that the chip detected
1573 on the SCSI BUS that prevents th
1574 properly.
1575 Bit 0x04 UDC Unexpected Disconnection
1576 Indicates that the device releas
1577 was not expecting this to happen
1578 indicate the SCSI initiator that
1579 using the SCSI protocol has occu
1580 Bit 0x02 RST SCSI BUS Reset
1581 Generally SCSI targets do not re
1582 device on the BUS can reset it a
1583 Bit 0x01 PAR Parity
1584 SCSI parity error detected.
1585 ======== ================================
1586
1587 On a faulty SCSI BUS, any error condition a
1588 PAR (0x01) may be detected by the chip. If
1589 encounters such error conditions, especiall
1590 BUS problem is likely the cause of these er
1591
1592 For fields D,E,F,G and H, you may look into t
1593 that contains some minimal comments on IO reg
1594
1595 Field D : SOCL Scsi Output Control Latch
1596 This register reflects the state of
1597 chip want to drive or compare again
1598
1599 Field E : SBCL Scsi Bus Control Lines
1600 Actual value of control lines on th
1601
1602 Field F : SBDL Scsi Bus Data Lines
1603 Actual value of data lines on the S
1604
1605 Field G : SXFER SCSI Transfer
1606 Contains the setting of the Synchro
1607 the current Synchronous offset (off
1608
1609 Field H : SCNTL3 Scsi Control Register 3
1610 Contains the setting of timing valu
1611 synchronous data transfers.
1612
1613 Understanding Fields I, J, K and dumps requir
1614 SCSI standards, chip cores functionnals and i
1615 You are not required to decode and understand
1616 maintain the driver code.
1617
1618 16. Synchronous transfer negotiation tables
1619 ===========================================
1620
1621 Tables below have been created by calling the
1622 for synchronisation negotiation timing calcul
1623 The first table corresponds to Ultra chips 53
1624 clock and 5 clock divisors.
1625 The second one has been calculated by setting
1626 and using 4 clock divisors and so applies to
1627 SCSI-2 mode.
1628
1629 Periods are in nano-seconds and speeds are in
1630 1 Mega-transfers/second means 1 MB/s with 8 b
1631 Wide16 SCSI.
1632
1633 16.1 Synchronous timings for 53C895, 53C875 a
1634
1635 +-----------------------------+--------+-----
1636 |Negotiated |NCR settings
1637 +-------+--------+------------+--------+-----
1638 |Factor |Period |Speed |Period |Speed
1639 +-------+--------+------------+--------+-----
1640 |10 | 25 |40.000 | 25 |40.00
1641 +-------+--------+------------+--------+-----
1642 |11 | 30.2 |33.112 | 31.25 |32.00
1643 +-------+--------+------------+--------+-----
1644 |12 | 50 |20.000 | 50 |20.00
1645 +-------+--------+------------+--------+-----
1646 |13 | 52 |19.230 | 62 |16.00
1647 +-------+--------+------------+--------+-----
1648 |14 | 56 |17.857 | 62 |16.00
1649 +-------+--------+------------+--------+-----
1650 |15 | 60 |16.666 | 62 |16.00
1651 +-------+--------+------------+--------+-----
1652 |16 | 64 |15.625 | 75 |13.33
1653 +-------+--------+------------+--------+-----
1654 |17 | 68 |14.705 | 75 |13.33
1655 +-------+--------+------------+--------+-----
1656 |18 | 72 |13.888 | 75 |13.33
1657 +-------+--------+------------+--------+-----
1658 |19 | 76 |13.157 | 87 |11.42
1659 +-------+--------+------------+--------+-----
1660 |20 | 80 |12.500 | 87 |11.42
1661 +-------+--------+------------+--------+-----
1662 |21 | 84 |11.904 | 87 |11.42
1663 +-------+--------+------------+--------+-----
1664 |22 | 88 |11.363 | 93 |10.66
1665 +-------+--------+------------+--------+-----
1666 |23 | 92 |10.869 | 93 |10.66
1667 +-------+--------+------------+--------+-----
1668 |24 | 96 |10.416 |100 |10.00
1669 +-------+--------+------------+--------+-----
1670 |25 |100 |10.000 |100 |10.00
1671 +-------+--------+------------+--------+-----
1672 |26 |104 | 9.615 |112 | 8.88
1673 +-------+--------+------------+--------+-----
1674 |27 |108 | 9.259 |112 | 8.88
1675 +-------+--------+------------+--------+-----
1676 |28 |112 | 8.928 |112 | 8.88
1677 +-------+--------+------------+--------+-----
1678 |29 |116 | 8.620 |125 | 8.00
1679 +-------+--------+------------+--------+-----
1680 |30 |120 | 8.333 |125 | 8.00
1681 +-------+--------+------------+--------+-----
1682 |31 |124 | 8.064 |125 | 8.00
1683 +-------+--------+------------+--------+-----
1684 |32 |128 | 7.812 |131 | 7.61
1685 +-------+--------+------------+--------+-----
1686 |33 |132 | 7.575 |150 | 6.66
1687 +-------+--------+------------+--------+-----
1688 |34 |136 | 7.352 |150 | 6.66
1689 +-------+--------+------------+--------+-----
1690 |35 |140 | 7.142 |150 | 6.66
1691 +-------+--------+------------+--------+-----
1692 |36 |144 | 6.944 |150 | 6.66
1693 +-------+--------+------------+--------+-----
1694 |37 |148 | 6.756 |150 | 6.66
1695 +-------+--------+------------+--------+-----
1696 |38 |152 | 6.578 |175 | 5.71
1697 +-------+--------+------------+--------+-----
1698 |39 |156 | 6.410 |175 | 5.71
1699 +-------+--------+------------+--------+-----
1700 |40 |160 | 6.250 |175 | 5.71
1701 +-------+--------+------------+--------+-----
1702 |41 |164 | 6.097 |175 | 5.71
1703 +-------+--------+------------+--------+-----
1704 |42 |168 | 5.952 |175 | 5.71
1705 +-------+--------+------------+--------+-----
1706 |43 |172 | 5.813 |175 | 5.71
1707 +-------+--------+------------+--------+-----
1708 |44 |176 | 5.681 |187 | 5.33
1709 +-------+--------+------------+--------+-----
1710 |45 |180 | 5.555 |187 | 5.33
1711 +-------+--------+------------+--------+-----
1712 |46 |184 | 5.434 |187 | 5.33
1713 +-------+--------+------------+--------+-----
1714 |47 |188 | 5.319 |200 | 5.00
1715 +-------+--------+------------+--------+-----
1716 |48 |192 | 5.208 |200 | 5.00
1717 +-------+--------+------------+--------+-----
1718 |49 |196 | 5.102 |200 | 5.00
1719 +-------+--------+------------+--------+-----
1720
1721 16.2 Synchronous timings for fast SCSI-2 53C8
1722
1723 +-----------------------------+--------------
1724 |Negotiated |NCR settings
1725 +-------+--------+------------+--------+-----
1726 |Factor |Period |Speed |Period |Speed
1727 +-------+--------+------------+--------+-----
1728 |25 |100 |10.000 |100 |10.00
1729 +-------+--------+------------+--------+-----
1730 |26 |104 |9.615 |125 | 8.00
1731 +-------+--------+------------+--------+-----
1732 |27 |108 |9.259 |125 | 8.00
1733 +-------+--------+------------+--------+-----
1734 |28 |112 |8.928 |125 | 8.00
1735 +-------+--------+------------+--------+-----
1736 |29 |116 |8.620 |125 | 8.00
1737 +-------+--------+------------+--------+-----
1738 |30 |120 |8.333 |125 | 8.00
1739 +-------+--------+------------+--------+-----
1740 |31 |124 |8.064 |125 | 8.00
1741 +-------+--------+------------+--------+-----
1742 |32 |128 |7.812 |131 | 7.61
1743 +-------+--------+------------+--------+-----
1744 |33 |132 |7.575 |150 | 6.66
1745 +-------+--------+------------+--------+-----
1746 |34 |136 |7.352 |150 | 6.66
1747 +-------+--------+------------+--------+-----
1748 |35 |140 |7.142 |150 | 6.66
1749 +-------+--------+------------+--------+-----
1750 |36 |144 |6.944 |150 | 6.66
1751 +-------+--------+------------+--------+-----
1752 |37 |148 |6.756 |150 | 6.66
1753 +-------+--------+------------+--------+-----
1754 |38 |152 |6.578 |175 | 5.71
1755 +-------+--------+------------+--------+-----
1756 |39 |156 |6.410 |175 | 5.71
1757 +-------+--------+------------+--------+-----
1758 |40 |160 |6.250 |175 | 5.71
1759 +-------+--------+------------+--------+-----
1760 |41 |164 |6.097 |175 | 5.71
1761 +-------+--------+------------+--------+-----
1762 |42 |168 |5.952 |175 | 5.71
1763 +-------+--------+------------+--------+-----
1764 |43 |172 |5.813 |175 | 5.71
1765 +-------+--------+------------+--------+-----
1766 |44 |176 |5.681 |187 | 5.33
1767 +-------+--------+------------+--------+-----
1768 |45 |180 |5.555 |187 | 5.33
1769 +-------+--------+------------+--------+-----
1770 |46 |184 |5.434 |187 | 5.33
1771 +-------+--------+------------+--------+-----
1772 |47 |188 |5.319 |200 | 5.00
1773 +-------+--------+------------+--------+-----
1774 |48 |192 |5.208 |200 | 5.00
1775 +-------+--------+------------+--------+-----
1776 |49 |196 |5.102 |200 | 5.00
1777 +-------+--------+------------+--------+-----
1778
1779
1780 17. Serial NVRAM
1781 ================
1782
1783 (added by Richard Waltham: dormouse@farsrobt.
1784
1785 17.1 Features
1786 -------------
1787
1788 Enabling serial NVRAM support enables detecti
1789 on Symbios and some Symbios compatible host a
1790 serial NVRAM is used by Symbios and Tekram to
1791 host adaptor and its attached drives.
1792
1793 The Symbios NVRAM also holds data on the boot
1794 system with more than one host adaptor. This
1795 the cards for drives to be changed from the d
1796 detection.
1797
1798 This can be done to a limited extent at the m
1799 this only changes the order of detection of d
1800 NVRAM boot order settings can do this as well
1801 types of cards are scanned in, something "rev
1802
1803 Tekram boards using Symbios chips, DC390W/F/U
1804 and this is used to distinguish between Symbi
1805 adaptors. This is used to disable the Symbios
1806 incorrectly set on Tekram boards if the CONFI
1807 configuration parameter is set enabling both
1808 used together with the Symbios cards using al
1809 "diff" support. ("led pin" support for Symbio
1810 enabled when using Tekram cards. It does noth
1811 adaptors but does not cause problems either.)
1812
1813
1814 17.2 Symbios NVRAM layout
1815 -------------------------
1816
1817 typical data at NVRAM address 0x100 (53c810a
1818
1819 00 00
1820 64 01
1821 8e 0b
1822
1823 00 30 00 00 00 00 07 00 00 00 00 00 00 00
1824
1825 04 00 0f 00 00 10 00 50 00 00 01 00 00 62
1826 04 00 03 00 00 10 00 58 00 00 01 00 00 63
1827 04 00 01 00 00 10 00 48 00 00 01 00 00 61
1828 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1829
1830 0f 00 08 08 64 00 0a 00
1831 0f 00 08 08 64 00 0a 00
1832 0f 00 08 08 64 00 0a 00
1833 0f 00 08 08 64 00 0a 00
1834 0f 00 08 08 64 00 0a 00
1835 0f 00 08 08 64 00 0a 00
1836 0f 00 08 08 64 00 0a 00
1837 0f 00 08 08 64 00 0a 00
1838
1839 0f 00 08 08 64 00 0a 00
1840 0f 00 08 08 64 00 0a 00
1841 0f 00 08 08 64 00 0a 00
1842 0f 00 08 08 64 00 0a 00
1843 0f 00 08 08 64 00 0a 00
1844 0f 00 08 08 64 00 0a 00
1845 0f 00 08 08 64 00 0a 00
1846 0f 00 08 08 64 00 0a 00
1847
1848 00 00 00 00 00 00 00 00
1849 00 00 00 00 00 00 00 00
1850 00 00 00 00 00 00 00 00
1851 00 00 00 00 00 00 00 00
1852 00 00 00 00 00 00 00 00
1853 00 00 00 00 00 00 00 00
1854 00 00 00 00 00 00 00 00
1855 00 00 00 00 00 00 00 00
1856
1857 00 00 00 00 00 00 00 00
1858 00 00 00 00 00 00 00 00
1859 00 00 00 00 00 00 00 00
1860 00 00 00 00 00 00 00 00
1861 00 00 00 00 00 00 00 00
1862 00 00 00 00 00 00 00 00
1863 00 00 00 00 00 00 00 00
1864 00 00 00 00 00 00 00 00
1865
1866 00 00 00 00 00 00 00 00
1867 00 00 00 00 00 00 00 00
1868 00 00 00 00 00 00 00 00
1869
1870 fe fe
1871 00 00
1872 00 00
1873
1874 NVRAM layout details
1875
1876 ============= ================
1877 NVRAM Address
1878 ============= ================
1879 0x000-0x0ff not used
1880 0x100-0x26f initialised data
1881 0x270-0x7ff not used
1882 ============= ================
1883
1884 general layout::
1885
1886 header - 6 bytes,
1887 data - 356 bytes (checksum is byte
1888 trailer - 6 bytes
1889 ---
1890 total 368 bytes
1891
1892 data area layout::
1893
1894 controller set up - 20 bytes
1895 boot configuration - 56 bytes (4x14
1896 device set up - 128 bytes (16x8
1897 unused (spare?) - 152 bytes (19x8
1898 ---
1899 total 356 bytes
1900
1901 header::
1902
1903 00 00 - ?? start marker
1904 64 01 - byte count (lsb/msb excludes he
1905 8e 0b - checksum (lsb/msb excludes head
1906
1907 controller set up::
1908
1909 00 30 00 00 00 00 07 00 00 00 00 00 00 00
1910 | | | |
1911 | | |
1912 | | |
1913 | | --Remo
1914 | | 0x0
1915 | | 0x0
1916 | | 0x0
1917 | |
1918 | --flag bits 2
1919 | 0x00000001= scan
1920 | (default 0x0
1921 --flag bits 1
1922 0x00000001 scam enabl
1923 0x00000010 parity ena
1924 0x00000100 verbose bo
1925
1926 remaining bytes unknown - they do not appear
1927 current set up for any of the controllers.
1928
1929 default set up is identical for 53c810a and 5
1930 (Removable Media added Symbios BIOS version 4
1931
1932 boot configuration
1933
1934 boot order set by order of the devices in thi
1935
1936 04 00 0f 00 00 10 00 50 00 00 01 00 00 62
1937 04 00 03 00 00 10 00 58 00 00 01 00 00 63
1938 04 00 01 00 00 10 00 48 00 00 01 00 00 61
1939 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1940 | | | | | | | |
1941 | | | | | | ---- P
1942 | | | | | --0x01 init/
1943 | | | | --PCI device/function
1944 | | ----- ?? PCI vendor ID (lsb/ms
1945 ----PCI device ID (lsb/msb)
1946
1947 ?? use of this data is a guess but seems
1948
1949 remaining bytes unknown - they do not appear
1950 current set up
1951
1952 default set up is identical for 53c810a and 5
1953 ---------------------------------------------
1954
1955 device set up (up to 16 devices - includes co
1956
1957 0f 00 08 08 64 00 0a 00 - id 0
1958 0f 00 08 08 64 00 0a 00
1959 0f 00 08 08 64 00 0a 00
1960 0f 00 08 08 64 00 0a 00
1961 0f 00 08 08 64 00 0a 00
1962 0f 00 08 08 64 00 0a 00
1963 0f 00 08 08 64 00 0a 00
1964 0f 00 08 08 64 00 0a 00
1965
1966 0f 00 08 08 64 00 0a 00
1967 0f 00 08 08 64 00 0a 00
1968 0f 00 08 08 64 00 0a 00
1969 0f 00 08 08 64 00 0a 00
1970 0f 00 08 08 64 00 0a 00
1971 0f 00 08 08 64 00 0a 00
1972 0f 00 08 08 64 00 0a 00
1973 0f 00 08 08 64 00 0a 00 - id 15
1974 | | | | | |
1975 | | | | ----timeout (lsb/msb)
1976 | | | --synch period (0x?? 40 Mtra
1977 | | | (0x30 20 Mtra
1978 | | | (0x64 10 Mtra
1979 | | | (0xc8 5 Mtra
1980 | | | (0x00 asynch
1981 | | -- ?? max sync offset (0x08 in
1982 | | (0x10 in
1983 | --device bus width (0x08 narrow)
1984 | (0x10 16 bit wi
1985 --flag bits
1986 0x00000001 - disconnect enabled
1987 0x00000010 - scan at boot time
1988 0x00000100 - scan luns
1989 0x00001000 - queue tags enabled
1990
1991 remaining bytes unknown - they do not appear
1992 current set up
1993
1994 ?? use of this data is a guess but seems reas
1995 (but it could be max bus width)
1996
1997 default set up for 53c810a NVRAM
1998 default set up for 53c875 NVRAM
1999
2000 - bus width
2001 - sync offset
2002 - sync period
2003
2004 ?? spare device space (32 bit bus ??)
2005
2006 ::
2007
2008 00 00 00 00 00 00 00 00 (19x8bytes)
2009 .
2010 .
2011 00 00 00 00 00 00 00 00
2012
2013 default set up is identical for 53c810a and 5
2014 ---------------------------------------------
2015
2016 trailer::
2017
2018 fe fe - ? end marker ?
2019 00 00
2020 00 00
2021
2022 default set up is identical for 53c810a and 5
2023 ---------------------------------------------
2024
2025
2026
2027 17.3 Tekram NVRAM layout
2028 ------------------------
2029
2030 nvram 64x16 (1024 bit)
2031
2032 Drive settings::
2033
2034 Drive ID 0-15 (addr 0x0yyyy0 = device set
2035 (addr 0x0yyyy1 = 0x0000)
2036
2037 x x x x x x x x x x x x x x x x
2038 | | | | | | | | |
2039 | | | | | | | | -----
2040 | | | | | | | |
2041 | | | | | | | |
2042 | | | | | | | -------
2043 | | | | | | |
2044 | | | | | | |
2045 | | | | | | ---------
2046 | | | | | |
2047 | | | | | |
2048 | | | | | -----------
2049 | | | | |
2050 | | | | |
2051 | | | | --------------
2052 | | | |
2053 | | | |
2054 | | | ----------------
2055 | | |
2056 | | |
2057 -------------------------
2058
2059
2060
2061
2062
2063
2064
2065
2066
2067
2068
2069
2070
2071 Global settings
2072
2073 Host flags 0 (addr 0x100000, 32)::
2074
2075 x x x x x x x x x x x x x x x x
2076 | | | | | | | | | | | |
2077 | | | | | | | | ----------- h
2078 | | | | | | | |
2079 | | | | | | | ----------------------- s
2080 | | | | | | | >
2081 | | | | | | |
2082 | | | | | | ------------------------- s
2083 | | | | | | >
2084 | | | | | |
2085 | | | | | --------------------------- b
2086 | | | | |
2087 | | | | |
2088 | | | | ----------------------------- a
2089 | | | |
2090 | | | |
2091 | | | -------------------------------- i
2092 | | |
2093 | | |
2094 | | ---------------------------------- s
2095 | |
2096 | |
2097 -------------------------------------- r
2098 a
2099
2100
2101 Host flags 1 (addr 0x100001, 33)::
2102
2103 x x x x x x x x x x x x x x x x
2104 | | | | | |
2105 | | | --------- b
2106 | | |
2107 | | |
2108 | | |
2109 | | |
2110 | | |
2111 | | |
2112 | | |
2113 --------------------------- m
2114
2115
2116
2117
2118
2119 Host flags 2 (addr 0x100010, 34)::
2120
2121 x x x x x x x x x x x x x x x x
2122 |
2123 ----- F
2124
2125
2126 checksum (addr 0x111111)
2127
2128 checksum = 0x1234 - (sum addr 0-63)
2129
2130 ---------------------------------------------
2131
2132 default nvram data::
2133
2134 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
2135 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
2136 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
2137 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
2138
2139 0x0f07 0x0400 0x0001 0x0000 0x0000 0x0000
2140 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
2141 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
2142 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
2143
2144
2145 18. Support for Big Endian
2146 ==========================
2147
2148 The PCI local bus has been primarily designed
2149 As a consequence, PCI devices generally expec
2150 byte ordering.
2151
2152 18.1 Big Endian CPU
2153 -------------------
2154
2155 In order to support NCR chips on a Big Endian
2156 perform byte reordering each time it is neede
2157 added to the driver by Cort <cort@cs.nmt.edu>
2158 version 2.5 and later ones. For the moment Bi
2159 been tested on Linux/PPC (PowerPC).
2160
2161 18.2 NCR chip in Big Endian mode of operation
2162 ---------------------------------------------
2163
2164 It can be read in SYMBIOS documentation that
2165 Big Endian mode, on paper: 53C815, 53C825A, 5
2166 This mode of operations is not software-selec
2167 BigLit to be pulled-up. Using this mode, most
2168 be avoided when the driver is running on a Bi
2169 Driver version 2.5 is also, in theory, ready
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.