1 .. SPDX-License-Identifier: GPL-2.0 1 .. SPDX-License-Identifier: GPL-2.0
2 2
3 =========================== 3 ===========================
4 NCR53C8XX/SYM53C8XX drivers 4 NCR53C8XX/SYM53C8XX drivers
5 =========================== 5 ===========================
6 6
7 Written by Gerard Roudier <groudier@free.fr> 7 Written by Gerard Roudier <groudier@free.fr>
8 8
9 21 Rue Carnot 9 21 Rue Carnot
10 10
11 95170 DEUIL LA BARRE - FRANCE 11 95170 DEUIL LA BARRE - FRANCE
12 12
13 29 May 1999 13 29 May 1999
14 14
15 .. Contents: 15 .. Contents:
16 16
17 1. Introduction 17 1. Introduction
18 2. Supported chips and SCSI features 18 2. Supported chips and SCSI features
19 3. Advantages of the enhanced 896 driver 19 3. Advantages of the enhanced 896 driver
20 3.1 Optimized SCSI SCRIPTS 20 3.1 Optimized SCSI SCRIPTS
21 3.2 New features of the SYM53C896 (64 21 3.2 New features of the SYM53C896 (64 bit PCI dual LVD SCSI controller)
22 4. Memory mapped I/O versus normal I/O 22 4. Memory mapped I/O versus normal I/O
23 5. Tagged command queueing 23 5. Tagged command queueing
24 6. Parity checking 24 6. Parity checking
25 7. Profiling information 25 7. Profiling information
26 8. Control commands 26 8. Control commands
27 8.1 Set minimum synchronous period 27 8.1 Set minimum synchronous period
28 8.2 Set wide size 28 8.2 Set wide size
29 8.3 Set maximum number of concurrent 29 8.3 Set maximum number of concurrent tagged commands
30 8.4 Set order type for tagged comman 30 8.4 Set order type for tagged command
31 8.5 Set debug mode 31 8.5 Set debug mode
32 8.6 Clear profile counters 32 8.6 Clear profile counters
33 8.7 Set flag (no_disc) 33 8.7 Set flag (no_disc)
34 8.8 Set verbose level 34 8.8 Set verbose level
35 8.9 Reset all logical units of a tar 35 8.9 Reset all logical units of a target
36 8.10 Abort all tasks of all logical u 36 8.10 Abort all tasks of all logical units of a target
37 9. Configuration parameters 37 9. Configuration parameters
38 10. Boot setup commands 38 10. Boot setup commands
39 10.1 Syntax 39 10.1 Syntax
40 10.2 Available arguments 40 10.2 Available arguments
41 10.2.1 Master parity checking 41 10.2.1 Master parity checking
42 10.2.2 Scsi parity checking 42 10.2.2 Scsi parity checking
43 10.2.3 Scsi disconnections 43 10.2.3 Scsi disconnections
44 10.2.4 Special features 44 10.2.4 Special features
45 10.2.5 Ultra SCSI support 45 10.2.5 Ultra SCSI support
46 10.2.6 Default number of tagg 46 10.2.6 Default number of tagged commands
47 10.2.7 Default synchronous pe 47 10.2.7 Default synchronous period factor
48 10.2.8 Negotiate synchronous 48 10.2.8 Negotiate synchronous with all devices
49 10.2.9 Verbosity level 49 10.2.9 Verbosity level
50 10.2.10 Debug mode 50 10.2.10 Debug mode
51 10.2.11 Burst max 51 10.2.11 Burst max
52 10.2.12 LED support 52 10.2.12 LED support
53 10.2.13 Max wide 53 10.2.13 Max wide
54 10.2.14 Differential mode 54 10.2.14 Differential mode
55 10.2.15 IRQ mode 55 10.2.15 IRQ mode
56 10.2.16 Reverse probe 56 10.2.16 Reverse probe
57 10.2.17 Fix up PCI configurati 57 10.2.17 Fix up PCI configuration space
58 10.2.18 Serial NVRAM 58 10.2.18 Serial NVRAM
59 10.2.19 Check SCSI BUS 59 10.2.19 Check SCSI BUS
60 10.2.20 Exclude a host from be 60 10.2.20 Exclude a host from being attached
61 10.2.21 Suggest a default SCSI 61 10.2.21 Suggest a default SCSI id for hosts
62 10.2.22 Enable use of IMMEDIAT 62 10.2.22 Enable use of IMMEDIATE ARBITRATION
63 10.3 Advised boot setup commands 63 10.3 Advised boot setup commands
64 10.4 PCI configuration fix-up boot op 64 10.4 PCI configuration fix-up boot option
65 10.5 Serial NVRAM support boot option 65 10.5 Serial NVRAM support boot option
66 10.6 SCSI BUS checking boot option 66 10.6 SCSI BUS checking boot option
67 10.7 IMMEDIATE ARBITRATION boot optio 67 10.7 IMMEDIATE ARBITRATION boot option
68 11. Some constants and flags of the ncr53c8 68 11. Some constants and flags of the ncr53c8xx.h header file
69 12. Installation 69 12. Installation
70 13. Architecture dependent features 70 13. Architecture dependent features
71 14. Known problems 71 14. Known problems
72 14.1 Tagged commands with Iomega Jaz 72 14.1 Tagged commands with Iomega Jaz device
73 14.2 Device names change when another 73 14.2 Device names change when another controller is added
74 14.3 Using only 8 bit devices with a 74 14.3 Using only 8 bit devices with a WIDE SCSI controller.
75 14.4 Possible data corruption during 75 14.4 Possible data corruption during a Memory Write and Invalidate
76 14.5 IRQ sharing problems 76 14.5 IRQ sharing problems
77 15. SCSI problem troubleshooting 77 15. SCSI problem troubleshooting
78 15.1 Problem tracking 78 15.1 Problem tracking
79 15.2 Understanding hardware error rep 79 15.2 Understanding hardware error reports
80 16. Synchronous transfer negotiation tables 80 16. Synchronous transfer negotiation tables
81 16.1 Synchronous timings for 53C875 a 81 16.1 Synchronous timings for 53C875 and 53C860 Ultra-SCSI controllers
82 16.2 Synchronous timings for fast SCS 82 16.2 Synchronous timings for fast SCSI-2 53C8XX controllers
83 17. Serial NVRAM support (by Richard Waltha 83 17. Serial NVRAM support (by Richard Waltham)
84 17.1 Features 84 17.1 Features
85 17.2 Symbios NVRAM layout 85 17.2 Symbios NVRAM layout
86 17.3 Tekram NVRAM layout 86 17.3 Tekram NVRAM layout
87 18. Support for Big Endian 87 18. Support for Big Endian
88 18.1 Big Endian CPU 88 18.1 Big Endian CPU
89 18.2 NCR chip in Big Endian mode of o 89 18.2 NCR chip in Big Endian mode of operations
90 90
91 1. Introduction 91 1. Introduction
92 =============== 92 ===============
93 93
94 The initial Linux ncr53c8xx driver has been a 94 The initial Linux ncr53c8xx driver has been a port of the ncr driver from
95 FreeBSD that has been achieved in November 199 95 FreeBSD that has been achieved in November 1995 by:
96 96
97 - Gerard Roudier <groudier 97 - Gerard Roudier <groudier@free.fr>
98 98
99 The original driver has been written for 386bs 99 The original driver has been written for 386bsd and FreeBSD by:
100 100
101 - Wolfgang Stanglmeier <wolf@col 101 - Wolfgang Stanglmeier <wolf@cologne.de>
102 - Stefan Esser <se@mi.Un 102 - Stefan Esser <se@mi.Uni-Koeln.de>
103 103
104 It is now available as a bundle of 2 drivers: 104 It is now available as a bundle of 2 drivers:
105 105
106 - ncr53c8xx generic driver that supports all t 106 - ncr53c8xx generic driver that supports all the SYM53C8XX family including
107 the earliest 810 rev. 1, the latest 896 (2 c 107 the earliest 810 rev. 1, the latest 896 (2 channel LVD SCSI controller) and
108 the new 895A (1 channel LVD SCSI controller) 108 the new 895A (1 channel LVD SCSI controller).
109 - sym53c8xx enhanced driver (a.k.a. 896 driver 109 - sym53c8xx enhanced driver (a.k.a. 896 drivers) that drops support of oldest
110 chips in order to gain advantage of new feat 110 chips in order to gain advantage of new features, as LOAD/STORE instructions
111 available since the 810A and hardware phase 111 available since the 810A and hardware phase mismatch available with the
112 896 and the 895A. 112 896 and the 895A.
113 113
114 You can find technical information about the N 114 You can find technical information about the NCR 8xx family in the
115 PCI-HOWTO written by Michael Will and in the S 115 PCI-HOWTO written by Michael Will and in the SCSI-HOWTO written by
116 Drew Eckhardt. 116 Drew Eckhardt.
117 117
118 Information about new chips is available at LS 118 Information about new chips is available at LSILOGIC web server:
119 119
120 - http://www.lsilogic.com/ 120 - http://www.lsilogic.com/
121 121
122 SCSI standard documentations are available at 122 SCSI standard documentations are available at SYMBIOS ftp server:
123 123
124 - ftp://ftp.symbios.com/ 124 - ftp://ftp.symbios.com/
125 125
126 Useful SCSI tools written by Eric Youngdale ar 126 Useful SCSI tools written by Eric Youngdale are available at tsx-11:
127 127
128 - ftp://tsx-11.mit.edu/pub/linux/ALP 128 - ftp://tsx-11.mit.edu/pub/linux/ALPHA/scsi/scsiinfo-X.Y.tar.gz
129 - ftp://tsx-11.mit.edu/pub/linux/ALP 129 - ftp://tsx-11.mit.edu/pub/linux/ALPHA/scsi/scsidev-X.Y.tar.gz
130 130
131 These tools are not ALPHA but quite clean and 131 These tools are not ALPHA but quite clean and work quite well.
132 It is essential you have the 'scsiinfo' packag 132 It is essential you have the 'scsiinfo' package.
133 133
134 This short documentation describes the feature 134 This short documentation describes the features of the generic and enhanced
135 drivers, configuration parameters and control 135 drivers, configuration parameters and control commands available through
136 the proc SCSI file system read / write operati 136 the proc SCSI file system read / write operations.
137 137
138 This driver has been tested OK with linux/i386 138 This driver has been tested OK with linux/i386, Linux/Alpha and Linux/PPC.
139 139
140 Latest driver version and patches are availabl 140 Latest driver version and patches are available at:
141 141
142 - ftp://ftp.tux.org/pub/people/gerar 142 - ftp://ftp.tux.org/pub/people/gerard-roudier
143 143
144 or 144 or
145 145
146 - ftp://ftp.symbios.com/mirror/ftp.t 146 - ftp://ftp.symbios.com/mirror/ftp.tux.org/pub/tux/roudier/drivers
147 147
148 I am not a native speaker of English and there 148 I am not a native speaker of English and there are probably lots of
149 mistakes in this README file. Any help will be 149 mistakes in this README file. Any help will be welcome.
150 150
151 151
152 2. Supported chips and SCSI features 152 2. Supported chips and SCSI features
153 ==================================== 153 ====================================
154 154
155 The following features are supported for all c 155 The following features are supported for all chips:
156 156
157 - Synchronous negotiation 157 - Synchronous negotiation
158 - Disconnection 158 - Disconnection
159 - Tagged command queuing 159 - Tagged command queuing
160 - SCSI parity checking 160 - SCSI parity checking
161 - Master parity checking 161 - Master parity checking
162 162
163 "Wide negotiation" is supported for chips that 163 "Wide negotiation" is supported for chips that allow it. The
164 following table shows some characteristics of 164 following table shows some characteristics of NCR 8xx family chips
165 and what drivers support them. 165 and what drivers support them.
166 166
167 +--------+-----------+-----+-----------+------ 167 +--------+-----------+-----+-----------+------------+------------+------------+
168 | | | | | 168 | | | | | |Supported by|Supported by|
169 | |On board | | | 169 | |On board | | | |the generic |the enhanced|
170 |Chip |SDMS BIOS |Wide |SCSI std. | Max. 170 |Chip |SDMS BIOS |Wide |SCSI std. | Max. sync |driver |driver |
171 +--------+-----------+-----+-----------+------ 171 +--------+-----------+-----+-----------+------------+------------+------------+
172 |810 | N | N | FAST10 | 10 MB 172 |810 | N | N | FAST10 | 10 MB/s | Y | N |
173 +--------+-----------+-----+-----------+------ 173 +--------+-----------+-----+-----------+------------+------------+------------+
174 |810A | N | N | FAST10 | 10 MB 174 |810A | N | N | FAST10 | 10 MB/s | Y | Y |
175 +--------+-----------+-----+-----------+------ 175 +--------+-----------+-----+-----------+------------+------------+------------+
176 |815 | Y | N | FAST10 | 10 MB 176 |815 | Y | N | FAST10 | 10 MB/s | Y | N |
177 +--------+-----------+-----+-----------+------ 177 +--------+-----------+-----+-----------+------------+------------+------------+
178 |825 | Y | Y | FAST10 | 20 MB 178 |825 | Y | Y | FAST10 | 20 MB/s | Y | N |
179 +--------+-----------+-----+-----------+------ 179 +--------+-----------+-----+-----------+------------+------------+------------+
180 |825A | Y | Y | FAST10 | 20 MB 180 |825A | Y | Y | FAST10 | 20 MB/s | Y | Y |
181 +--------+-----------+-----+-----------+------ 181 +--------+-----------+-----+-----------+------------+------------+------------+
182 |860 | N | N | FAST20 | 20 MB 182 |860 | N | N | FAST20 | 20 MB/s | Y | Y |
183 +--------+-----------+-----+-----------+------ 183 +--------+-----------+-----+-----------+------------+------------+------------+
184 |875 | Y | Y | FAST20 | 40 MB 184 |875 | Y | Y | FAST20 | 40 MB/s | Y | Y |
185 +--------+-----------+-----+-----------+------ 185 +--------+-----------+-----+-----------+------------+------------+------------+
186 |876 | Y | Y | FAST20 | 40 MB 186 |876 | Y | Y | FAST20 | 40 MB/s | Y | Y |
187 +--------+-----------+-----+-----------+------ 187 +--------+-----------+-----+-----------+------------+------------+------------+
188 |895 | Y | Y | FAST40 | 80 MB 188 |895 | Y | Y | FAST40 | 80 MB/s | Y | Y |
189 +--------+-----------+-----+-----------+------ 189 +--------+-----------+-----+-----------+------------+------------+------------+
190 |895A | Y | Y | FAST40 | 80 MB 190 |895A | Y | Y | FAST40 | 80 MB/s | Y | Y |
191 +--------+-----------+-----+-----------+------ 191 +--------+-----------+-----+-----------+------------+------------+------------+
192 |896 | Y | Y | FAST40 | 80 MB 192 |896 | Y | Y | FAST40 | 80 MB/s | Y | Y |
193 +--------+-----------+-----+-----------+------ 193 +--------+-----------+-----+-----------+------------+------------+------------+
194 |897 | Y | Y | FAST40 | 80 MB 194 |897 | Y | Y | FAST40 | 80 MB/s | Y | Y |
195 +--------+-----------+-----+-----------+------ 195 +--------+-----------+-----+-----------+------------+------------+------------+
196 |1510D | Y | Y | FAST40 | 80 MB 196 |1510D | Y | Y | FAST40 | 80 MB/s | Y | Y |
197 +--------+-----------+-----+-----------+------ 197 +--------+-----------+-----+-----------+------------+------------+------------+
198 |1010 | Y | Y | FAST80 |160 MB 198 |1010 | Y | Y | FAST80 |160 MB/s | N | Y |
199 +--------+-----------+-----+-----------+------ 199 +--------+-----------+-----+-----------+------------+------------+------------+
200 |1010_66 | Y | Y | FAST80 |160 MB 200 |1010_66 | Y | Y | FAST80 |160 MB/s | N | Y |
201 |[1]_ | | | | 201 |[1]_ | | | | | | |
202 +--------+-----------+-----+-----------+------ 202 +--------+-----------+-----+-----------+------------+------------+------------+
203 203
204 .. [1] Chip supports 33MHz and 66MHz PCI buses 204 .. [1] Chip supports 33MHz and 66MHz PCI buses.
205 205
206 206
207 Summary of other supported features: 207 Summary of other supported features:
208 208
209 :Module: allow to load the driv 209 :Module: allow to load the driver
210 :Memory mapped I/O: increases performance 210 :Memory mapped I/O: increases performance
211 :Profiling information: read operations from t 211 :Profiling information: read operations from the proc SCSI file system
212 :Control commands: write operations to th 212 :Control commands: write operations to the proc SCSI file system
213 :Debugging information: written to syslog (exp 213 :Debugging information: written to syslog (expert only)
214 :Serial NVRAM: Symbios and Tekram for 214 :Serial NVRAM: Symbios and Tekram formats
215 215
216 - Scatter / gather 216 - Scatter / gather
217 - Shared interrupt 217 - Shared interrupt
218 - Boot setup commands 218 - Boot setup commands
219 219
220 220
221 3. Advantages of the enhanced 896 driver 221 3. Advantages of the enhanced 896 driver
222 ======================================== 222 ========================================
223 223
224 3.1 Optimized SCSI SCRIPTS 224 3.1 Optimized SCSI SCRIPTS
225 -------------------------- 225 --------------------------
226 226
227 The 810A, 825A, 875, 895, 896 and 895A support 227 The 810A, 825A, 875, 895, 896 and 895A support new SCSI SCRIPTS instructions
228 named LOAD and STORE that allow to move up to 228 named LOAD and STORE that allow to move up to 1 DWORD from/to an IO register
229 to/from memory much faster that the MOVE MEMOR 229 to/from memory much faster that the MOVE MEMORY instruction that is supported
230 by the 53c7xx and 53c8xx family. 230 by the 53c7xx and 53c8xx family.
231 The LOAD/STORE instructions support absolute a 231 The LOAD/STORE instructions support absolute and DSA relative addressing
232 modes. The SCSI SCRIPTS had been entirely rew 232 modes. The SCSI SCRIPTS had been entirely rewritten using LOAD/STORE instead
233 of MOVE MEMORY instructions. 233 of MOVE MEMORY instructions.
234 234
235 3.2 New features of the SYM53C896 (64 bit PCI 235 3.2 New features of the SYM53C896 (64 bit PCI dual LVD SCSI controller)
236 ---------------------------------------------- 236 -----------------------------------------------------------------------
237 237
238 The 896 and the 895A allows handling of the ph 238 The 896 and the 895A allows handling of the phase mismatch context from
239 SCRIPTS (avoids the phase mismatch interrupt t 239 SCRIPTS (avoids the phase mismatch interrupt that stops the SCSI processor
240 until the C code has saved the context of the 240 until the C code has saved the context of the transfer).
241 Implementing this without using LOAD/STORE ins 241 Implementing this without using LOAD/STORE instructions would be painful
242 and I didn't even want to try it. 242 and I didn't even want to try it.
243 243
244 The 896 chip supports 64 bit PCI transactions 244 The 896 chip supports 64 bit PCI transactions and addressing, while the
245 895A supports 32 bit PCI transactions and 64 b 245 895A supports 32 bit PCI transactions and 64 bit addressing.
246 The SCRIPTS processor of these chips is not tr 246 The SCRIPTS processor of these chips is not true 64 bit, but uses segment
247 registers for bit 32-63. Another interesting f 247 registers for bit 32-63. Another interesting feature is that LOAD/STORE
248 instructions that address the on-chip RAM (8k) 248 instructions that address the on-chip RAM (8k) remain internal to the chip.
249 249
250 Due to the use of LOAD/STORE SCRIPTS instructi 250 Due to the use of LOAD/STORE SCRIPTS instructions, this driver does not
251 support the following chips: 251 support the following chips:
252 252
253 - SYM53C810 revision < 0x10 (16) 253 - SYM53C810 revision < 0x10 (16)
254 - SYM53C815 all revisions 254 - SYM53C815 all revisions
255 - SYM53C825 revision < 0x10 (16) 255 - SYM53C825 revision < 0x10 (16)
256 256
257 4. Memory mapped I/O versus normal I/O 257 4. Memory mapped I/O versus normal I/O
258 ====================================== 258 ======================================
259 259
260 Memory mapped I/O has less latency than normal 260 Memory mapped I/O has less latency than normal I/O. Since
261 linux-1.3.x, memory mapped I/O is used rather 261 linux-1.3.x, memory mapped I/O is used rather than normal I/O. Memory
262 mapped I/O seems to work fine on most hardware 262 mapped I/O seems to work fine on most hardware configurations, but
263 some poorly designed motherboards may break th 263 some poorly designed motherboards may break this feature.
264 264
265 The configuration option CONFIG_SCSI_NCR53C8XX 265 The configuration option CONFIG_SCSI_NCR53C8XX_IOMAPPED forces the
266 driver to use normal I/O in all cases. 266 driver to use normal I/O in all cases.
267 267
268 268
269 5. Tagged command queueing 269 5. Tagged command queueing
270 ========================== 270 ==========================
271 271
272 Queuing more than 1 command at a time to a dev 272 Queuing more than 1 command at a time to a device allows it to perform
273 optimizations based on actual head positions a 273 optimizations based on actual head positions and its mechanical
274 characteristics. This feature may also reduce 274 characteristics. This feature may also reduce average command latency.
275 In order to really gain advantage of this feat 275 In order to really gain advantage of this feature, devices must have
276 a reasonable cache size (No miracle is to be e 276 a reasonable cache size (No miracle is to be expected for a low-end
277 hard disk with 128 KB or less). 277 hard disk with 128 KB or less).
278 Some known SCSI devices do not properly suppor 278 Some known SCSI devices do not properly support tagged command queuing.
279 Generally, firmware revisions that fix this ki 279 Generally, firmware revisions that fix this kind of problems are available
280 at respective vendor web/ftp sites. 280 at respective vendor web/ftp sites.
281 All I can say is that the hard disks I use on 281 All I can say is that the hard disks I use on my machines behave well with
282 this driver with tagged command queuing enable 282 this driver with tagged command queuing enabled:
283 283
284 - IBM S12 0662 284 - IBM S12 0662
285 - Conner 1080S 285 - Conner 1080S
286 - Quantum Atlas I 286 - Quantum Atlas I
287 - Quantum Atlas II 287 - Quantum Atlas II
288 288
289 If your controller has NVRAM, you can configur 289 If your controller has NVRAM, you can configure this feature per target
290 from the user setup tool. The Tekram Setup pro 290 from the user setup tool. The Tekram Setup program allows to tune the
291 maximum number of queued commands up to 32. Th 291 maximum number of queued commands up to 32. The Symbios Setup only allows
292 to enable or disable this feature. 292 to enable or disable this feature.
293 293
294 The maximum number of simultaneous tagged comm 294 The maximum number of simultaneous tagged commands queued to a device
295 is currently set to 8 by default. This value 295 is currently set to 8 by default. This value is suitable for most SCSI
296 disks. With large SCSI disks (>= 2GB, cache > 296 disks. With large SCSI disks (>= 2GB, cache >= 512KB, average seek time
297 <= 10 ms), using a larger value may give bette 297 <= 10 ms), using a larger value may give better performances.
298 298
299 The sym53c8xx driver supports up to 255 comman 299 The sym53c8xx driver supports up to 255 commands per device, and the
300 generic ncr53c8xx driver supports up to 64, bu 300 generic ncr53c8xx driver supports up to 64, but using more than 32 is
301 generally not worth-while, unless you are usin 301 generally not worth-while, unless you are using a very large disk or disk
302 array. It is noticeable that most of recent ha 302 array. It is noticeable that most of recent hard disks seem not to accept
303 more than 64 simultaneous commands. So, using 303 more than 64 simultaneous commands. So, using more than 64 queued commands
304 is probably just resource wasting. 304 is probably just resource wasting.
305 305
306 If your controller does not have NVRAM or if i 306 If your controller does not have NVRAM or if it is managed by the SDMS
307 BIOS/SETUP, you can configure tagged queueing 307 BIOS/SETUP, you can configure tagged queueing feature and device queue
308 depths from the boot command-line. For example 308 depths from the boot command-line. For example::
309 309
310 ncr53c8xx=tags:4/t2t3q15-t4q7/t1u0q32 310 ncr53c8xx=tags:4/t2t3q15-t4q7/t1u0q32
311 311
312 will set tagged commands queue depths as follo 312 will set tagged commands queue depths as follow:
313 313
314 - target 2 all luns on controller 0 --> 15 314 - target 2 all luns on controller 0 --> 15
315 - target 3 all luns on controller 0 --> 15 315 - target 3 all luns on controller 0 --> 15
316 - target 4 all luns on controller 0 --> 7 316 - target 4 all luns on controller 0 --> 7
317 - target 1 lun 0 on controller 1 --> 32 317 - target 1 lun 0 on controller 1 --> 32
318 - all other target/lun --> 4 318 - all other target/lun --> 4
319 319
320 In some special conditions, some SCSI disk fir 320 In some special conditions, some SCSI disk firmwares may return a
321 QUEUE FULL status for a SCSI command. This beh 321 QUEUE FULL status for a SCSI command. This behaviour is managed by the
322 driver using the following heuristic: 322 driver using the following heuristic:
323 323
324 - Each time a QUEUE FULL status is returned, t 324 - Each time a QUEUE FULL status is returned, tagged queue depth is reduced
325 to the actual number of disconnected command 325 to the actual number of disconnected commands.
326 326
327 - Every 1000 successfully completed SCSI comma 327 - Every 1000 successfully completed SCSI commands, if allowed by the
328 current limit, the maximum number of queueab 328 current limit, the maximum number of queueable commands is incremented.
329 329
330 Since QUEUE FULL status reception and handling 330 Since QUEUE FULL status reception and handling is resource wasting, the
331 driver notifies by default this problem to use 331 driver notifies by default this problem to user by indicating the actual
332 number of commands used and their status, as w 332 number of commands used and their status, as well as its decision on the
333 device queue depth change. 333 device queue depth change.
334 The heuristic used by the driver in handling Q 334 The heuristic used by the driver in handling QUEUE FULL ensures that the
335 impact on performances is not too bad. You can 335 impact on performances is not too bad. You can get rid of the messages by
336 setting verbose level to zero, as follow: 336 setting verbose level to zero, as follow:
337 337
338 1st method: 338 1st method:
339 boot your system using 'ncr53c8xx= 339 boot your system using 'ncr53c8xx=verb:0' option.
340 340
341 2nd method: 341 2nd method:
342 apply "setverbose 0" control comma 342 apply "setverbose 0" control command to the proc fs entry
343 corresponding to your controller a 343 corresponding to your controller after boot-up.
344 344
345 6. Parity checking 345 6. Parity checking
346 ================== 346 ==================
347 347
348 The driver supports SCSI parity checking and P 348 The driver supports SCSI parity checking and PCI bus master parity
349 checking. These features must be enabled in o 349 checking. These features must be enabled in order to ensure safe data
350 transfers. However, some flawed devices or mo 350 transfers. However, some flawed devices or mother boards will have
351 problems with parity. You can disable either P 351 problems with parity. You can disable either PCI parity or SCSI parity
352 checking by entering appropriate options from 352 checking by entering appropriate options from the boot command line.
353 (See 10: Boot setup commands). 353 (See 10: Boot setup commands).
354 354
355 7. Profiling information 355 7. Profiling information
356 ======================== 356 ========================
357 357
358 Profiling information is available through the 358 Profiling information is available through the proc SCSI file system.
359 Since gathering profiling information may impa 359 Since gathering profiling information may impact performances, this
360 feature is disabled by default and requires a 360 feature is disabled by default and requires a compilation configuration
361 option to be set to Y. 361 option to be set to Y.
362 362
363 The device associated with a host has the foll 363 The device associated with a host has the following pathname::
364 364
365 /proc/scsi/ncr53c8xx/N (N=0,1,2 365 /proc/scsi/ncr53c8xx/N (N=0,1,2 ....)
366 366
367 Generally, only 1 board is used on hardware co 367 Generally, only 1 board is used on hardware configuration, and that device is::
368 368
369 /proc/scsi/ncr53c8xx/0 369 /proc/scsi/ncr53c8xx/0
370 370
371 However, if the driver has been made as module 371 However, if the driver has been made as module, the number of the
372 hosts is incremented each time the driver is l 372 hosts is incremented each time the driver is loaded.
373 373
374 In order to display profiling information, jus 374 In order to display profiling information, just enter::
375 375
376 cat /proc/scsi/ncr53c8xx/0 376 cat /proc/scsi/ncr53c8xx/0
377 377
378 and you will get something like the following 378 and you will get something like the following text::
379 379
380 General information: 380 General information:
381 Chip NCR53C810, device id 0x1, revision id 381 Chip NCR53C810, device id 0x1, revision id 0x2
382 IO port address 0x6000, IRQ number 10 382 IO port address 0x6000, IRQ number 10
383 Using memory mapped IO at virtual address 383 Using memory mapped IO at virtual address 0x282c000
384 Synchronous transfer period 25, max comman 384 Synchronous transfer period 25, max commands per lun 4
385 Profiling information: 385 Profiling information:
386 num_trans = 18014 386 num_trans = 18014
387 num_kbytes = 671314 387 num_kbytes = 671314
388 num_disc = 25763 388 num_disc = 25763
389 num_break = 1673 389 num_break = 1673
390 num_int = 1685 390 num_int = 1685
391 num_fly = 18038 391 num_fly = 18038
392 ms_setup = 4940 392 ms_setup = 4940
393 ms_data = 369940 393 ms_data = 369940
394 ms_disc = 183090 394 ms_disc = 183090
395 ms_post = 1320 395 ms_post = 1320
396 396
397 General information is easy to understand. The 397 General information is easy to understand. The device ID and the
398 revision ID identify the SCSI chip as follows: 398 revision ID identify the SCSI chip as follows:
399 399
400 ======= ============= =========== 400 ======= ============= ===========
401 Chip Device id Revision Id 401 Chip Device id Revision Id
402 ======= ============= =========== 402 ======= ============= ===========
403 810 0x1 < 0x10 403 810 0x1 < 0x10
404 810A 0x1 >= 0x10 404 810A 0x1 >= 0x10
405 815 0x4 405 815 0x4
406 825 0x3 < 0x10 406 825 0x3 < 0x10
407 860 0x6 407 860 0x6
408 825A 0x3 >= 0x10 408 825A 0x3 >= 0x10
409 875 0xf 409 875 0xf
410 895 0xc 410 895 0xc
411 ======= ============= =========== 411 ======= ============= ===========
412 412
413 The profiling information is updated upon comp 413 The profiling information is updated upon completion of SCSI commands.
414 A data structure is allocated and zeroed when 414 A data structure is allocated and zeroed when the host adapter is
415 attached. So, if the driver is a module, the p 415 attached. So, if the driver is a module, the profile counters are
416 cleared each time the driver is loaded. The " 416 cleared each time the driver is loaded. The "clearprof" command
417 allows you to clear these counters at any time 417 allows you to clear these counters at any time.
418 418
419 The following counters are available: 419 The following counters are available:
420 420
421 ("num" prefix means "number of", 421 ("num" prefix means "number of",
422 "ms" means milli-seconds) 422 "ms" means milli-seconds)
423 423
424 num_trans 424 num_trans
425 Number of completed commands 425 Number of completed commands
426 Example above: 18014 completed command 426 Example above: 18014 completed commands
427 427
428 num_kbytes 428 num_kbytes
429 Number of kbytes transferred 429 Number of kbytes transferred
430 Example above: 671 MB transferred 430 Example above: 671 MB transferred
431 431
432 num_disc 432 num_disc
433 Number of SCSI disconnections 433 Number of SCSI disconnections
434 Example above: 25763 SCSI disconnectio 434 Example above: 25763 SCSI disconnections
435 435
436 num_break 436 num_break
437 number of script interruptions (phase 437 number of script interruptions (phase mismatch)
438 Example above: 1673 script interruptio 438 Example above: 1673 script interruptions
439 439
440 num_int 440 num_int
441 Number of interrupts other than "on th 441 Number of interrupts other than "on the fly"
442 Example above: 1685 interruptions not 442 Example above: 1685 interruptions not "on the fly"
443 443
444 num_fly 444 num_fly
445 Number of interrupts "on the fly" 445 Number of interrupts "on the fly"
446 Example above: 18038 interruptions "on 446 Example above: 18038 interruptions "on the fly"
447 447
448 ms_setup 448 ms_setup
449 Elapsed time for SCSI commands setups 449 Elapsed time for SCSI commands setups
450 Example above: 4.94 seconds 450 Example above: 4.94 seconds
451 451
452 ms_data 452 ms_data
453 Elapsed time for data transfers 453 Elapsed time for data transfers
454 Example above: 369.94 seconds spent fo 454 Example above: 369.94 seconds spent for data transfer
455 455
456 ms_disc 456 ms_disc
457 Elapsed time for SCSI disconnections 457 Elapsed time for SCSI disconnections
458 Example above: 183.09 seconds spent di 458 Example above: 183.09 seconds spent disconnected
459 459
460 ms_post 460 ms_post
461 Elapsed time for command post processi 461 Elapsed time for command post processing
462 (time from SCSI status get to command 462 (time from SCSI status get to command completion call)
463 Example above: 1.32 seconds spent for 463 Example above: 1.32 seconds spent for post processing
464 464
465 Due to the 1/100 second tick of the system clo 465 Due to the 1/100 second tick of the system clock, "ms_post" time may
466 be wrong. 466 be wrong.
467 467
468 In the example above, we got 18038 interrupts 468 In the example above, we got 18038 interrupts "on the fly" and only
469 1673 script breaks generally due to disconnect 469 1673 script breaks generally due to disconnections inside a segment
470 of the scatter list. 470 of the scatter list.
471 471
472 472
473 8. Control commands 473 8. Control commands
474 =================== 474 ===================
475 475
476 Control commands can be sent to the driver wit 476 Control commands can be sent to the driver with write operations to
477 the proc SCSI file system. The generic command 477 the proc SCSI file system. The generic command syntax is the
478 following:: 478 following::
479 479
480 echo "<verb> <parameters>" >/proc/scsi/n 480 echo "<verb> <parameters>" >/proc/scsi/ncr53c8xx/0
481 (assumes controller number is 0) 481 (assumes controller number is 0)
482 482
483 Using "all" for "<target>" parameter with the 483 Using "all" for "<target>" parameter with the commands below will
484 apply to all targets of the SCSI chain (except 484 apply to all targets of the SCSI chain (except the controller).
485 485
486 Available commands: 486 Available commands:
487 487
488 8.1 Set minimum synchronous period factor 488 8.1 Set minimum synchronous period factor
489 ----------------------------------------- 489 -----------------------------------------
490 490
491 setsync <target> <period factor> 491 setsync <target> <period factor>
492 492
493 :target: target number 493 :target: target number
494 :period: minimum synchronous period. 494 :period: minimum synchronous period.
495 Maximum speed = 1000/(4*period 495 Maximum speed = 1000/(4*period factor) except for special
496 cases below. 496 cases below.
497 497
498 Specify a period of 255, to force asynchro 498 Specify a period of 255, to force asynchronous transfer mode.
499 499
500 - 10 means 25 nano-seconds synchronous p 500 - 10 means 25 nano-seconds synchronous period
501 - 11 means 30 nano-seconds synchronous p 501 - 11 means 30 nano-seconds synchronous period
502 - 12 means 50 nano-seconds synchronous p 502 - 12 means 50 nano-seconds synchronous period
503 503
504 8.2 Set wide size 504 8.2 Set wide size
505 ----------------- 505 -----------------
506 506
507 setwide <target> <size> 507 setwide <target> <size>
508 508
509 :target: target number 509 :target: target number
510 :size: 0=8 bits, 1=16bits 510 :size: 0=8 bits, 1=16bits
511 511
512 8.3 Set maximum number of concurrent tagged co 512 8.3 Set maximum number of concurrent tagged commands
513 ---------------------------------------------- 513 ----------------------------------------------------
514 514
515 settags <target> <tags> 515 settags <target> <tags>
516 516
517 :target: target number 517 :target: target number
518 :tags: number of concurrent tagged com 518 :tags: number of concurrent tagged commands
519 must not be greater than SCSI_N 519 must not be greater than SCSI_NCR_MAX_TAGS (default: 8)
520 520
521 8.4 Set order type for tagged command 521 8.4 Set order type for tagged command
522 ------------------------------------- 522 -------------------------------------
523 523
524 setorder <order> 524 setorder <order>
525 525
526 :order: 3 possible values: 526 :order: 3 possible values:
527 527
528 simple: 528 simple:
529 use SIMPLE TAG for all 529 use SIMPLE TAG for all operations (read and write)
530 530
531 ordered: 531 ordered:
532 use ORDERED TAG for al 532 use ORDERED TAG for all operations
533 533
534 default: 534 default:
535 use default tag type, 535 use default tag type,
536 SIMPLE TAG for read 536 SIMPLE TAG for read operations
537 ORDERED TAG for write 537 ORDERED TAG for write operations
538 538
539 539
540 8.5 Set debug mode 540 8.5 Set debug mode
541 ------------------ 541 ------------------
542 542
543 setdebug <list of debug flags> 543 setdebug <list of debug flags>
544 544
545 Available debug flags: 545 Available debug flags:
546 546
547 ======== ============================= 547 ======== ========================================================
548 alloc print info about memory alloc 548 alloc print info about memory allocations (ccb, lcb)
549 queue print info about insertions i 549 queue print info about insertions into the command start queue
550 result print sense data on CHECK CON 550 result print sense data on CHECK CONDITION status
551 scatter print info about the scatter 551 scatter print info about the scatter process
552 scripts print info about the script b 552 scripts print info about the script binding process
553 tiny print minimal debugging infor 553 tiny print minimal debugging information
554 timing print timing information of t 554 timing print timing information of the NCR chip
555 nego print information about SCSI 555 nego print information about SCSI negotiations
556 phase print information on script i 556 phase print information on script interruptions
557 ======== ============================= 557 ======== ========================================================
558 558
559 Use "setdebug" with no argument to reset d 559 Use "setdebug" with no argument to reset debug flags.
560 560
561 561
562 8.6 Clear profile counters 562 8.6 Clear profile counters
563 -------------------------- 563 --------------------------
564 564
565 clearprof 565 clearprof
566 566
567 The profile counters are automatically cle 567 The profile counters are automatically cleared when the amount of
568 data transferred reaches 1000 GB in order 568 data transferred reaches 1000 GB in order to avoid overflow.
569 The "clearprof" command allows you to clea 569 The "clearprof" command allows you to clear these counters at any time.
570 570
571 571
572 8.7 Set flag (no_disc) 572 8.7 Set flag (no_disc)
573 ---------------------- 573 ----------------------
574 574
575 setflag <target> <flag> 575 setflag <target> <flag>
576 576
577 target: target number 577 target: target number
578 578
579 For the moment, only one flag is available 579 For the moment, only one flag is available:
580 580
581 no_disc: not allow target to disconn 581 no_disc: not allow target to disconnect.
582 582
583 Do not specify any flag in order to reset 583 Do not specify any flag in order to reset the flag. For example:
584 584
585 setflag 4 585 setflag 4
586 will reset no_disc flag for target 4, so 586 will reset no_disc flag for target 4, so will allow it disconnections.
587 587
588 setflag all 588 setflag all
589 will allow disconnection for all devices 589 will allow disconnection for all devices on the SCSI bus.
590 590
591 591
592 8.8 Set verbose level 592 8.8 Set verbose level
593 --------------------- 593 ---------------------
594 594
595 setverbose #level 595 setverbose #level
596 596
597 The driver default verbose level is 1. Thi 597 The driver default verbose level is 1. This command allows to change
598 th driver verbose level after boot-up. 598 th driver verbose level after boot-up.
599 599
600 8.9 Reset all logical units of a target 600 8.9 Reset all logical units of a target
601 --------------------------------------- 601 ---------------------------------------
602 602
603 resetdev <target> 603 resetdev <target>
604 604
605 :target: target number 605 :target: target number
606 606
607 The driver will try to send a BUS DEVICE R 607 The driver will try to send a BUS DEVICE RESET message to the target.
608 (Only supported by the SYM53C8XX driver an 608 (Only supported by the SYM53C8XX driver and provided for test purpose)
609 609
610 8.10 Abort all tasks of all logical units of a 610 8.10 Abort all tasks of all logical units of a target
611 ---------------------------------------------- 611 -----------------------------------------------------
612 612
613 cleardev <target> 613 cleardev <target>
614 614
615 :target: target number 615 :target: target number
616 616
617 The driver will try to send a ABORT messag 617 The driver will try to send a ABORT message to all the logical units
618 of the target. 618 of the target.
619 619
620 (Only supported by the SYM53C8XX driver an 620 (Only supported by the SYM53C8XX driver and provided for test purpose)
621 621
622 622
623 9. Configuration parameters 623 9. Configuration parameters
624 =========================== 624 ===========================
625 625
626 If the firmware of all your devices is perfect 626 If the firmware of all your devices is perfect enough, all the
627 features supported by the driver can be enable 627 features supported by the driver can be enabled at start-up. However,
628 if only one has a flaw for some SCSI feature, 628 if only one has a flaw for some SCSI feature, you can disable the
629 support by the driver of this feature at linux 629 support by the driver of this feature at linux start-up and enable
630 this feature after boot-up only for devices th 630 this feature after boot-up only for devices that support it safely.
631 631
632 CONFIG_SCSI_NCR53C8XX_IOMAPPED (default 632 CONFIG_SCSI_NCR53C8XX_IOMAPPED (default answer: n)
633 Answer "y" if you suspect your mother boar 633 Answer "y" if you suspect your mother board to not allow memory mapped I/O.
634 634
635 May slow down performance a little. This 635 May slow down performance a little. This option is required by
636 Linux/PPC and is used no matter what you s 636 Linux/PPC and is used no matter what you select here. Linux/PPC
637 suffers no performance loss with this opti 637 suffers no performance loss with this option since all IO is memory
638 mapped anyway. 638 mapped anyway.
639 639
640 CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS (default 640 CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS (default answer: 8)
641 Default tagged command queue depth. 641 Default tagged command queue depth.
642 642
643 CONFIG_SCSI_NCR53C8XX_MAX_TAGS (defaul 643 CONFIG_SCSI_NCR53C8XX_MAX_TAGS (default answer: 8)
644 This option allows you to specify the maxi 644 This option allows you to specify the maximum number of tagged commands
645 that can be queued to a device. The maximu 645 that can be queued to a device. The maximum supported value is 32.
646 646
647 CONFIG_SCSI_NCR53C8XX_SYNC (default 647 CONFIG_SCSI_NCR53C8XX_SYNC (default answer: 5)
648 This option allows you to specify the freq 648 This option allows you to specify the frequency in MHz the driver
649 will use at boot time for synchronous data 649 will use at boot time for synchronous data transfer negotiations.
650 This frequency can be changed later with t 650 This frequency can be changed later with the "setsync" control command.
651 0 means "asynchronous data transfers". 651 0 means "asynchronous data transfers".
652 652
653 CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO (default 653 CONFIG_SCSI_NCR53C8XX_FORCE_SYNC_NEGO (default answer: n)
654 Force synchronous negotiation for all SCSI 654 Force synchronous negotiation for all SCSI-2 devices.
655 655
656 Some SCSI-2 devices do not report this fea 656 Some SCSI-2 devices do not report this feature in byte 7 of inquiry
657 response but do support it properly (TAMAR 657 response but do support it properly (TAMARACK scanners for example).
658 658
659 CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT (default 659 CONFIG_SCSI_NCR53C8XX_NO_DISCONNECT (default and only reasonable answer: n)
660 If you suspect a device of yours does not 660 If you suspect a device of yours does not properly support disconnections,
661 you can answer "y". Then, all SCSI devices 661 you can answer "y". Then, all SCSI devices will never disconnect the bus
662 even while performing long SCSI operations 662 even while performing long SCSI operations.
663 663
664 CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT 664 CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT
665 Genuine SYMBIOS boards use GPIO0 in output 665 Genuine SYMBIOS boards use GPIO0 in output for controller LED and GPIO3
666 bit as a flag indicating singled-ended/dif 666 bit as a flag indicating singled-ended/differential interface.
667 If all the boards of your system are genui 667 If all the boards of your system are genuine SYMBIOS boards or use
668 BIOS and drivers from SYMBIOS, you would w 668 BIOS and drivers from SYMBIOS, you would want to enable this option.
669 669
670 This option must NOT be enabled if your sy 670 This option must NOT be enabled if your system has at least one 53C8XX
671 based scsi board with a vendor-specific BI 671 based scsi board with a vendor-specific BIOS.
672 For example, Tekram DC-390/U, DC-390/W and 672 For example, Tekram DC-390/U, DC-390/W and DC-390/F scsi controllers
673 use a vendor-specific BIOS and are known t 673 use a vendor-specific BIOS and are known to not use SYMBIOS compatible
674 GPIO wiring. So, this option must not be e 674 GPIO wiring. So, this option must not be enabled if your system has
675 such a board installed. 675 such a board installed.
676 676
677 CONFIG_SCSI_NCR53C8XX_NVRAM_DETECT 677 CONFIG_SCSI_NCR53C8XX_NVRAM_DETECT
678 Enable support for reading the serial NVRA 678 Enable support for reading the serial NVRAM data on Symbios and
679 some Symbios compatible cards, and Tekram 679 some Symbios compatible cards, and Tekram DC390W/U/F cards. Useful for
680 systems with more than one Symbios compati 680 systems with more than one Symbios compatible controller where at least
681 one has a serial NVRAM, or for a system wi 681 one has a serial NVRAM, or for a system with a mixture of Symbios and
682 Tekram cards. Enables setting the boot ord 682 Tekram cards. Enables setting the boot order of host adaptors
683 to something other than the default order 683 to something other than the default order or "reverse probe" order.
684 Also enables Symbios and Tekram cards to b 684 Also enables Symbios and Tekram cards to be distinguished so
685 CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT may b 685 CONFIG_SCSI_NCR53C8XX_SYMBIOS_COMPAT may be set in a system with a
686 mixture of Symbios and Tekram cards so the 686 mixture of Symbios and Tekram cards so the Symbios cards can make use of
687 the full range of Symbios features, differ 687 the full range of Symbios features, differential, led pin, without
688 causing problems for the Tekram card(s). 688 causing problems for the Tekram card(s).
689 689
690 10. Boot setup commands 690 10. Boot setup commands
691 ======================= 691 =======================
692 692
693 10.1 Syntax 693 10.1 Syntax
694 ----------- 694 -----------
695 695
696 Setup commands can be passed to the driver eit 696 Setup commands can be passed to the driver either at boot time or as a
697 string variable using 'insmod'. 697 string variable using 'insmod'.
698 698
699 A boot setup command for the ncr53c8xx (sym53c 699 A boot setup command for the ncr53c8xx (sym53c8xx) driver begins with the
700 driver name "ncr53c8xx="(sym53c8xx). The kerne 700 driver name "ncr53c8xx="(sym53c8xx). The kernel syntax parser then expects
701 an optional list of integers separated with co 701 an optional list of integers separated with comma followed by an optional
702 list of comma-separated strings. Example of bo 702 list of comma-separated strings. Example of boot setup command under lilo
703 prompt:: 703 prompt::
704 704
705 lilo: linux root=/dev/hda2 ncr53c8xx=tags: 705 lilo: linux root=/dev/hda2 ncr53c8xx=tags:4,sync:10,debug:0x200
706 706
707 - enable tagged commands, up to 4 tagged comma 707 - enable tagged commands, up to 4 tagged commands queued.
708 - set synchronous negotiation speed to 10 Mega 708 - set synchronous negotiation speed to 10 Mega-transfers / second.
709 - set DEBUG_NEGO flag. 709 - set DEBUG_NEGO flag.
710 710
711 Since comma seems not to be allowed when defin 711 Since comma seems not to be allowed when defining a string variable using
712 'insmod', the driver also accepts <space> as o 712 'insmod', the driver also accepts <space> as option separator.
713 The following command will install driver modu 713 The following command will install driver module with the same options as
714 above:: 714 above::
715 715
716 insmod ncr53c8xx.o ncr53c8xx="tags:4 sync: 716 insmod ncr53c8xx.o ncr53c8xx="tags:4 sync:10 debug:0x200"
717 717
718 For the moment, the integer list of arguments 718 For the moment, the integer list of arguments is discarded by the driver.
719 It will be used in the future in order to allo 719 It will be used in the future in order to allow a per controller setup.
720 720
721 Each string argument must be specified as "key 721 Each string argument must be specified as "keyword:value". Only lower-case
722 characters and digits are allowed. 722 characters and digits are allowed.
723 723
724 In a system that contains multiple 53C8xx adap 724 In a system that contains multiple 53C8xx adapters insmod will install the
725 specified driver on each adapter. To exclude a 725 specified driver on each adapter. To exclude a chip use the 'excl' keyword.
726 726
727 The sequence of commands:: 727 The sequence of commands::
728 728
729 insmod sym53c8xx sym53c8xx=excl:0x1400 729 insmod sym53c8xx sym53c8xx=excl:0x1400
730 insmod ncr53c8xx 730 insmod ncr53c8xx
731 731
732 installs the sym53c8xx driver on all adapters 732 installs the sym53c8xx driver on all adapters except the one at IO port
733 address 0x1400 and then installs the ncr53c8xx 733 address 0x1400 and then installs the ncr53c8xx driver to the adapter at IO
734 port address 0x1400. 734 port address 0x1400.
735 735
736 736
737 10.2 Available arguments 737 10.2 Available arguments
738 ------------------------ 738 ------------------------
739 739
740 10.2.1 Master parity checking 740 10.2.1 Master parity checking
741 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 741 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
742 742
743 ====== ======== 743 ====== ========
744 mpar:y enabled 744 mpar:y enabled
745 mpar:n disabled 745 mpar:n disabled
746 ====== ======== 746 ====== ========
747 747
748 10.2.2 Scsi parity checking 748 10.2.2 Scsi parity checking
749 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 749 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^
750 750
751 ====== ======== 751 ====== ========
752 spar:y enabled 752 spar:y enabled
753 spar:n disabled 753 spar:n disabled
754 ====== ======== 754 ====== ========
755 755
756 10.2.3 Scsi disconnections 756 10.2.3 Scsi disconnections
757 ^^^^^^^^^^^^^^^^^^^^^^^^^^^ 757 ^^^^^^^^^^^^^^^^^^^^^^^^^^^
758 758
759 ====== ======== 759 ====== ========
760 disc:y enabled 760 disc:y enabled
761 disc:n disabled 761 disc:n disabled
762 ====== ======== 762 ====== ========
763 763
764 10.2.4 Special features 764 10.2.4 Special features
765 ^^^^^^^^^^^^^^^^^^^^^^^^ 765 ^^^^^^^^^^^^^^^^^^^^^^^^
766 766
767 Only apply to 810A, 825A, 860, 875 and 895 767 Only apply to 810A, 825A, 860, 875 and 895 controllers.
768 Have no effect with other ones. 768 Have no effect with other ones.
769 769
770 ======= =========================== 770 ======= =================================================
771 specf:y (or 1) enabled 771 specf:y (or 1) enabled
772 specf:n (or 0) disabled 772 specf:n (or 0) disabled
773 specf:3 enabled except Memor 773 specf:3 enabled except Memory Write And Invalidate
774 ======= =========================== 774 ======= =================================================
775 775
776 The default driver setup is 'specf:3'. As a 776 The default driver setup is 'specf:3'. As a consequence, option 'specf:y'
777 must be specified in the boot setup command 777 must be specified in the boot setup command to enable Memory Write And
778 Invalidate. 778 Invalidate.
779 779
780 10.2.5 Ultra SCSI support 780 10.2.5 Ultra SCSI support
781 ^^^^^^^^^^^^^^^^^^^^^^^^^^ 781 ^^^^^^^^^^^^^^^^^^^^^^^^^^
782 782
783 Only apply to 860, 875, 895, 895a, 896, 101 783 Only apply to 860, 875, 895, 895a, 896, 1010 and 1010_66 controllers.
784 Have no effect with other ones. 784 Have no effect with other ones.
785 785
786 ======= ======================== 786 ======= ========================
787 ultra:n All ultra speeds enabled 787 ultra:n All ultra speeds enabled
788 ultra:2 Ultra2 enabled 788 ultra:2 Ultra2 enabled
789 ultra:1 Ultra enabled 789 ultra:1 Ultra enabled
790 ultra:0 Ultra speeds disabled 790 ultra:0 Ultra speeds disabled
791 ======= ======================== 791 ======= ========================
792 792
793 10.2.6 Default number of tagged commands 793 10.2.6 Default number of tagged commands
794 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 794 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
795 795
796 ======================= ============== 796 ======================= ===============================
797 tags:0 (or tags:1 ) tagged command 797 tags:0 (or tags:1 ) tagged command queuing disabled
798 tags:#tags (#tags > 1) tagged command 798 tags:#tags (#tags > 1) tagged command queuing enabled
799 ======================= ============== 799 ======================= ===============================
800 800
801 #tags will be truncated to the max queued co 801 #tags will be truncated to the max queued commands configuration parameter.
802 This option also allows to specify a command 802 This option also allows to specify a command queue depth for each device
803 that support tagged command queueing. 803 that support tagged command queueing.
804 804
805 Example:: 805 Example::
806 806
807 ncr53c8xx=tags:10/t2t3q16-t5q24/t1u2q32 807 ncr53c8xx=tags:10/t2t3q16-t5q24/t1u2q32
808 808
809 will set devices queue depth as follow: 809 will set devices queue depth as follow:
810 810
811 - controller #0 target #2 and target #3 811 - controller #0 target #2 and target #3 -> 16 commands,
812 - controller #0 target #5 812 - controller #0 target #5 -> 24 commands,
813 - controller #1 target #1 logical unit # 813 - controller #1 target #1 logical unit #2 -> 32 commands,
814 - all other logical units (all targets, 814 - all other logical units (all targets, all controllers) -> 10 commands.
815 815
816 10.2.7 Default synchronous period factor 816 10.2.7 Default synchronous period factor
817 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 817 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
818 818
819 ============ ================================= 819 ============ ========================================================
820 sync:255 disabled (asynchronous transfer m 820 sync:255 disabled (asynchronous transfer mode)
821 sync:#factor 821 sync:#factor
822 ============ ================ 822 ============ =======================================
823 #factor = 10 Ultra-2 SCSI 40 823 #factor = 10 Ultra-2 SCSI 40 Mega-transfers / second
824 #factor = 11 Ultra-2 SCSI 33 824 #factor = 11 Ultra-2 SCSI 33 Mega-transfers / second
825 #factor < 25 Ultra SCSI 20 825 #factor < 25 Ultra SCSI 20 Mega-transfers / second
826 #factor < 50 Fast SCSI-2 826 #factor < 50 Fast SCSI-2
827 ============ ================ 827 ============ =======================================
828 ============ ================================= 828 ============ ========================================================
829 829
830 In all cases, the driver will use the minimu 830 In all cases, the driver will use the minimum transfer period supported by
831 controllers according to NCR53C8XX chip type 831 controllers according to NCR53C8XX chip type.
832 832
833 10.2.8 Negotiate synchronous with all devices 833 10.2.8 Negotiate synchronous with all devices
834 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 834 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
835 (force sync nego) 835 (force sync nego)
836 836
837 ===== ========= 837 ===== =========
838 fsn:y enabled 838 fsn:y enabled
839 fsn:n disabled 839 fsn:n disabled
840 ===== ========= 840 ===== =========
841 841
842 10.2.9 Verbosity level 842 10.2.9 Verbosity level
843 ^^^^^^^^^^^^^^^^^^^^^^^ 843 ^^^^^^^^^^^^^^^^^^^^^^^
844 844
845 ====== ========= 845 ====== =========
846 verb:0 minimal 846 verb:0 minimal
847 verb:1 normal 847 verb:1 normal
848 verb:2 too much 848 verb:2 too much
849 ====== ========= 849 ====== =========
850 850
851 10.2.10 Debug mode 851 10.2.10 Debug mode
852 ^^^^^^^^^^^^^^^^^^ 852 ^^^^^^^^^^^^^^^^^^
853 853
854 ======== =================================== 854 ======== ==================================================================
855 debug:0 clear debug flags 855 debug:0 clear debug flags
856 debug:#x set debug flags 856 debug:#x set debug flags
857 857
858 #x is an integer value combining t 858 #x is an integer value combining the following power-of-2 values:
859 859
860 ============= ====== 860 ============= ======
861 DEBUG_ALLOC 0x1 861 DEBUG_ALLOC 0x1
862 DEBUG_PHASE 0x2 862 DEBUG_PHASE 0x2
863 DEBUG_POLL 0x4 863 DEBUG_POLL 0x4
864 DEBUG_QUEUE 0x8 864 DEBUG_QUEUE 0x8
865 DEBUG_RESULT 0x10 865 DEBUG_RESULT 0x10
866 DEBUG_SCATTER 0x20 866 DEBUG_SCATTER 0x20
867 DEBUG_SCRIPT 0x40 867 DEBUG_SCRIPT 0x40
868 DEBUG_TINY 0x80 868 DEBUG_TINY 0x80
869 DEBUG_TIMING 0x100 869 DEBUG_TIMING 0x100
870 DEBUG_NEGO 0x200 870 DEBUG_NEGO 0x200
871 DEBUG_TAGS 0x400 871 DEBUG_TAGS 0x400
872 DEBUG_FREEZE 0x800 872 DEBUG_FREEZE 0x800
873 DEBUG_RESTART 0x1000 873 DEBUG_RESTART 0x1000
874 ============= ====== 874 ============= ======
875 ======== =================================== 875 ======== ==================================================================
876 876
877 You can play safely with DEBUG_NEGO. However 877 You can play safely with DEBUG_NEGO. However, some of these flags may
878 generate bunches of syslog messages. 878 generate bunches of syslog messages.
879 879
880 10.2.11 Burst max 880 10.2.11 Burst max
881 ^^^^^^^^^^^^^^^^^ 881 ^^^^^^^^^^^^^^^^^
882 882
883 ========= =================================== 883 ========= ==================================================================
884 burst:0 burst disabled 884 burst:0 burst disabled
885 burst:255 get burst length from initial IO re 885 burst:255 get burst length from initial IO register settings.
886 burst:#x burst enabled (1<<#x burst transfer 886 burst:#x burst enabled (1<<#x burst transfers max)
887 887
888 #x is an integer value which is log 888 #x is an integer value which is log base 2 of the burst transfers
889 max. 889 max.
890 890
891 The NCR53C875 and NCR53C825A suppor 891 The NCR53C875 and NCR53C825A support up to 128 burst transfers
892 (#x = 7). 892 (#x = 7).
893 893
894 Other chips only support up to 16 ( 894 Other chips only support up to 16 (#x = 4).
895 895
896 This is a maximum value. The driver 896 This is a maximum value. The driver set the burst length according
897 to chip and revision ids. By defaul 897 to chip and revision ids. By default the driver uses the maximum
898 value supported by the chip. 898 value supported by the chip.
899 ========= =================================== 899 ========= ==================================================================
900 900
901 10.2.12 LED support 901 10.2.12 LED support
902 ^^^^^^^^^^^^^^^^^^^ 902 ^^^^^^^^^^^^^^^^^^^
903 903
904 ===== =================== 904 ===== ===================
905 led:1 enable LED support 905 led:1 enable LED support
906 led:0 disable LED support 906 led:0 disable LED support
907 ===== =================== 907 ===== ===================
908 908
909 Do not enable LED support if your scsi board 909 Do not enable LED support if your scsi board does not use SDMS BIOS.
910 (See 'Configuration parameters') 910 (See 'Configuration parameters')
911 911
912 10.2.13 Max wide 912 10.2.13 Max wide
913 ^^^^^^^^^^^^^^^^ 913 ^^^^^^^^^^^^^^^^
914 914
915 ====== =================== 915 ====== ===================
916 wide:1 wide scsi enabled 916 wide:1 wide scsi enabled
917 wide:0 wide scsi disabled 917 wide:0 wide scsi disabled
918 ====== =================== 918 ====== ===================
919 919
920 Some scsi boards use a 875 (ultra wide) and 920 Some scsi boards use a 875 (ultra wide) and only supply narrow connectors.
921 If you have connected a wide device with a 5 921 If you have connected a wide device with a 50 pins to 68 pins cable
922 converter, any accepted wide negotiation wil 922 converter, any accepted wide negotiation will break further data transfers.
923 In such a case, using "wide:0" in the bootup 923 In such a case, using "wide:0" in the bootup command will be helpful.
924 924
925 10.2.14 Differential mode 925 10.2.14 Differential mode
926 ^^^^^^^^^^^^^^^^^^^^^^^^^ 926 ^^^^^^^^^^^^^^^^^^^^^^^^^
927 927
928 ====== ============================== 928 ====== =================================
929 diff:0 never set up diff mode 929 diff:0 never set up diff mode
930 diff:1 set up diff mode if BIOS set i 930 diff:1 set up diff mode if BIOS set it
931 diff:2 always set up diff mode 931 diff:2 always set up diff mode
932 diff:3 set diff mode if GPIO3 is not 932 diff:3 set diff mode if GPIO3 is not set
933 ====== ============================== 933 ====== =================================
934 934
935 10.2.15 IRQ mode 935 10.2.15 IRQ mode
936 ^^^^^^^^^^^^^^^^ 936 ^^^^^^^^^^^^^^^^
937 937
938 ========= =========================== 938 ========= ========================================================
939 irqm:0 always open drain 939 irqm:0 always open drain
940 irqm:1 same as initial settings (a 940 irqm:1 same as initial settings (assumed BIOS settings)
941 irqm:2 always totem pole 941 irqm:2 always totem pole
942 irqm:0x10 driver will not use IRQF_SH 942 irqm:0x10 driver will not use IRQF_SHARED flag when requesting irq
943 ========= =========================== 943 ========= ========================================================
944 944
945 (Bits 0x10 and 0x20 can be combined with h 945 (Bits 0x10 and 0x20 can be combined with hardware irq mode option)
946 946
947 10.2.16 Reverse probe 947 10.2.16 Reverse probe
948 ^^^^^^^^^^^^^^^^^^^^^ 948 ^^^^^^^^^^^^^^^^^^^^^
949 949
950 ========= ========================== 950 ========= ========================================================
951 revprob:n probe chip ids from the PC 951 revprob:n probe chip ids from the PCI configuration in this order:
952 810, 815, 820, 860, 875, 8 952 810, 815, 820, 860, 875, 885, 895, 896
953 revprob:y probe chip ids in the reve 953 revprob:y probe chip ids in the reverse order.
954 ========= ========================== 954 ========= ========================================================
955 955
956 10.2.17 Fix up PCI configuration space 956 10.2.17 Fix up PCI configuration space
957 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 957 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
958 pcifix:<option bits> 958 pcifix:<option bits>
959 959
960 Available option bits: 960 Available option bits:
961 961
962 === =============================== 962 === ===============================================================
963 0x0 No attempt to fix PCI configura 963 0x0 No attempt to fix PCI configuration space registers values.
964 0x1 Set PCI cache-line size registe 964 0x1 Set PCI cache-line size register if not set.
965 0x2 Set write and invalidate bit in 965 0x2 Set write and invalidate bit in PCI command register.
966 0x4 Increase if necessary PCI laten 966 0x4 Increase if necessary PCI latency timer according to burst max.
967 === =============================== 967 === ===============================================================
968 968
969 Use 'pcifix:7' in order to allow the drive 969 Use 'pcifix:7' in order to allow the driver to fix up all PCI features.
970 970
971 10.2.18 Serial NVRAM 971 10.2.18 Serial NVRAM
972 ^^^^^^^^^^^^^^^^^^^^ 972 ^^^^^^^^^^^^^^^^^^^^
973 973
974 ======= ========================== 974 ======= =========================================
975 nvram:n do not look for serial NVR 975 nvram:n do not look for serial NVRAM
976 nvram:y test controllers for onboa 976 nvram:y test controllers for onboard serial NVRAM
977 ======= ========================== 977 ======= =========================================
978 978
979 (alternate binary form) 979 (alternate binary form)
980 mvram=<bits options> 980 mvram=<bits options>
981 981
982 ==== =============================== 982 ==== =================================================================
983 0x01 look for NVRAM (equivalent to 983 0x01 look for NVRAM (equivalent to nvram=y)
984 0x02 ignore NVRAM "Synchronous negot 984 0x02 ignore NVRAM "Synchronous negotiation" parameters for all devices
985 0x04 ignore NVRAM "Wide negotiation" 985 0x04 ignore NVRAM "Wide negotiation" parameter for all devices
986 0x08 ignore NVRAM "Scan at boot time 986 0x08 ignore NVRAM "Scan at boot time" parameter for all devices
987 0x80 also attach controllers set to 987 0x80 also attach controllers set to OFF in the NVRAM (sym53c8xx only)
988 ==== =============================== 988 ==== =================================================================
989 989
990 10.2.19 Check SCSI BUS 990 10.2.19 Check SCSI BUS
991 ^^^^^^^^^^^^^^^^^^^^^^ 991 ^^^^^^^^^^^^^^^^^^^^^^
992 992
993 buschk:<option bits> 993 buschk:<option bits>
994 994
995 Available option bits: 995 Available option bits:
996 996
997 ==== =============================== 997 ==== ================================================
998 0x0: No check. 998 0x0: No check.
999 0x1: Check and do not attach the con 999 0x1: Check and do not attach the controller on error.
1000 0x2: Check and just warn on error. 1000 0x2: Check and just warn on error.
1001 0x4: Disable SCSI bus integrity che 1001 0x4: Disable SCSI bus integrity checking.
1002 ==== ============================== 1002 ==== ================================================
1003 1003
1004 10.2.20 Exclude a host from being attached 1004 10.2.20 Exclude a host from being attached
1005 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1005 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1006 1006
1007 excl=<io_address> 1007 excl=<io_address>
1008 1008
1009 Prevent host at a given io address from b 1009 Prevent host at a given io address from being attached.
1010 For example 'ncr53c8xx=excl:0xb400,excl:0 1010 For example 'ncr53c8xx=excl:0xb400,excl:0xc000' indicate to the
1011 ncr53c8xx driver not to attach hosts at a 1011 ncr53c8xx driver not to attach hosts at address 0xb400 and 0xc000.
1012 1012
1013 10.2.21 Suggest a default SCSI id for hosts 1013 10.2.21 Suggest a default SCSI id for hosts
1014 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1014 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1015 1015
1016 ========== ===================== 1016 ========== ==========================================
1017 hostid:255 no id suggested. 1017 hostid:255 no id suggested.
1018 hostid:#x (0 < x < 7) x suggest 1018 hostid:#x (0 < x < 7) x suggested for hosts SCSI id.
1019 ========== ===================== 1019 ========== ==========================================
1020 1020
1021 If a host SCSI id is available from the N 1021 If a host SCSI id is available from the NVRAM, the driver will ignore
1022 any value suggested as boot option. Other 1022 any value suggested as boot option. Otherwise, if a suggested value
1023 different from 255 has been supplied, it 1023 different from 255 has been supplied, it will use it. Otherwise, it will
1024 try to deduce the value previously set in 1024 try to deduce the value previously set in the hardware and use value
1025 7 if the hardware value is zero. 1025 7 if the hardware value is zero.
1026 1026
1027 10.2.22 Enable use of IMMEDIATE ARBITRATION 1027 10.2.22 Enable use of IMMEDIATE ARBITRATION
1028 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1028 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1029 1029
1030 (only supported by the sym53c8xx driv 1030 (only supported by the sym53c8xx driver. See 10.7 for more details)
1031 1031
1032 ======= =================================== 1032 ======= =================================================================
1033 iarb:0 do not use this feature. 1033 iarb:0 do not use this feature.
1034 iarb:#x use this feature according to bit f 1034 iarb:#x use this feature according to bit fields as follow:
1035 1035
1036 ========= ========================= 1036 ========= =======================================================
1037 bit 0 (1) enable IARB each time the 1037 bit 0 (1) enable IARB each time the initiator has been reselected
1038 when it arbitrated for th 1038 when it arbitrated for the SCSI BUS.
1039 (#x >> 4) maximum number of success 1039 (#x >> 4) maximum number of successive settings of IARB if the
1040 initiator win arbitration 1040 initiator win arbitration and it has other commands
1041 to send to a device. 1041 to send to a device.
1042 ========= ========================= 1042 ========= =======================================================
1043 ======= =================================== 1043 ======= =================================================================
1044 1044
1045 Boot fail safe 1045 Boot fail safe
1046 safe:y load the following assumed fa 1046 safe:y load the following assumed fail safe initial setup
1047 1047
1048 ======================== ============= 1048 ======================== ====================== ==========
1049 master parity disabled 1049 master parity disabled mpar:n
1050 scsi parity enabled 1050 scsi parity enabled spar:y
1051 disconnections not allowed 1051 disconnections not allowed disc:n
1052 special features disabled 1052 special features disabled specf:n
1053 ultra scsi disabled 1053 ultra scsi disabled ultra:n
1054 force sync negotiation disabled 1054 force sync negotiation disabled fsn:n
1055 reverse probe disabled 1055 reverse probe disabled revprob:n
1056 PCI fix up disabled 1056 PCI fix up disabled pcifix:0
1057 serial NVRAM enabled 1057 serial NVRAM enabled nvram:y
1058 verbosity level 2 1058 verbosity level 2 verb:2
1059 tagged command queuing disabled 1059 tagged command queuing disabled tags:0
1060 synchronous negotiation disabled 1060 synchronous negotiation disabled sync:255
1061 debug flags none 1061 debug flags none debug:0
1062 burst length from BIOS set 1062 burst length from BIOS settings burst:255
1063 LED support disabled 1063 LED support disabled led:0
1064 wide support disabled 1064 wide support disabled wide:0
1065 settle time 10 seconds 1065 settle time 10 seconds settle:10
1066 differential support from BIOS set 1066 differential support from BIOS settings diff:1
1067 irq mode from BIOS set 1067 irq mode from BIOS settings irqm:1
1068 SCSI BUS check do not attach 1068 SCSI BUS check do not attach on error buschk:1
1069 immediate arbitration disabled 1069 immediate arbitration disabled iarb:0
1070 ======================== ============= 1070 ======================== ====================== ==========
1071 1071
1072 10.3 Advised boot setup commands 1072 10.3 Advised boot setup commands
1073 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1073 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1074 1074
1075 If the driver has been configured with defaul 1075 If the driver has been configured with default options, the equivalent
1076 boot setup is:: 1076 boot setup is::
1077 1077
1078 ncr53c8xx=mpar:y,spar:y,disc:y,specf:3,fsn 1078 ncr53c8xx=mpar:y,spar:y,disc:y,specf:3,fsn:n,ultra:2,fsn:n,revprob:n,verb:1\
1079 tags:0,sync:50,debug:0,burst:7,l 1079 tags:0,sync:50,debug:0,burst:7,led:0,wide:1,settle:2,diff:0,irqm:0
1080 1080
1081 For an installation diskette or a safe but no 1081 For an installation diskette or a safe but not fast system,
1082 boot setup can be:: 1082 boot setup can be::
1083 1083
1084 ncr53c8xx=safe:y,mpar:y,disc:y 1084 ncr53c8xx=safe:y,mpar:y,disc:y
1085 ncr53c8xx=safe:y,disc:y 1085 ncr53c8xx=safe:y,disc:y
1086 ncr53c8xx=safe:y,mpar:y 1086 ncr53c8xx=safe:y,mpar:y
1087 ncr53c8xx=safe:y 1087 ncr53c8xx=safe:y
1088 1088
1089 My personal system works flawlessly with the 1089 My personal system works flawlessly with the following equivalent setup::
1090 1090
1091 ncr53c8xx=mpar:y,spar:y,disc:y,specf:1,fsn 1091 ncr53c8xx=mpar:y,spar:y,disc:y,specf:1,fsn:n,ultra:2,fsn:n,revprob:n,verb:1\
1092 tags:32,sync:12,debug:0,burst:7, 1092 tags:32,sync:12,debug:0,burst:7,led:1,wide:1,settle:2,diff:0,irqm:0
1093 1093
1094 The driver prints its actual setup when verbo 1094 The driver prints its actual setup when verbosity level is 2. You can try
1095 "ncr53c8xx=verb:2" to get the "static" setup 1095 "ncr53c8xx=verb:2" to get the "static" setup of the driver, or add "verb:2"
1096 to your boot setup command in order to check 1096 to your boot setup command in order to check the actual setup the driver is
1097 using. 1097 using.
1098 1098
1099 10.4 PCI configuration fix-up boot option 1099 10.4 PCI configuration fix-up boot option
1100 ----------------------------------------- 1100 -----------------------------------------
1101 1101
1102 pcifix:<option bits> 1102 pcifix:<option bits>
1103 1103
1104 Available option bits: 1104 Available option bits:
1105 1105
1106 === ================================ 1106 === =====================================================
1107 0x1 Set PCI cache-line size register 1107 0x1 Set PCI cache-line size register if not set.
1108 0x2 Set write and invalidate bit in 1108 0x2 Set write and invalidate bit in PCI command register.
1109 === ================================ 1109 === =====================================================
1110 1110
1111 Use 'pcifix:3' in order to allow the driver t 1111 Use 'pcifix:3' in order to allow the driver to fix both PCI features.
1112 1112
1113 These options only apply to new SYMBIOS chips 1113 These options only apply to new SYMBIOS chips 810A, 825A, 860, 875
1114 and 895 and are only supported for Pentium an 1114 and 895 and are only supported for Pentium and 486 class processors.
1115 Recent SYMBIOS 53C8XX scsi processors are abl 1115 Recent SYMBIOS 53C8XX scsi processors are able to use PCI read multiple
1116 and PCI write and invalidate commands. These 1116 and PCI write and invalidate commands. These features require the
1117 cache line size register to be properly set i 1117 cache line size register to be properly set in the PCI configuration
1118 space of the chips. On the other hand, chips 1118 space of the chips. On the other hand, chips will use PCI write and
1119 invalidate commands only if the corresponding 1119 invalidate commands only if the corresponding bit is set to 1 in the
1120 PCI command register. 1120 PCI command register.
1121 1121
1122 Not all PCI bioses set the PCI cache line reg 1122 Not all PCI bioses set the PCI cache line register and the PCI write and
1123 invalidate bit in the PCI configuration space 1123 invalidate bit in the PCI configuration space of 53C8XX chips.
1124 Optimized PCI accesses may be broken for some 1124 Optimized PCI accesses may be broken for some PCI/memory controllers or
1125 make problems with some PCI boards. 1125 make problems with some PCI boards.
1126 1126
1127 This fix-up worked flawlessly on my previous 1127 This fix-up worked flawlessly on my previous system.
1128 (MB Triton HX / 53C875 / 53C810A) 1128 (MB Triton HX / 53C875 / 53C810A)
1129 I use these options at my own risks as you wi 1129 I use these options at my own risks as you will do if you decide to
1130 use them too. 1130 use them too.
1131 1131
1132 1132
1133 10.5 Serial NVRAM support boot option 1133 10.5 Serial NVRAM support boot option
1134 ------------------------------------- 1134 -------------------------------------
1135 1135
1136 ======= ================================= 1136 ======= =========================================
1137 nvram:n do not look for serial NVRAM 1137 nvram:n do not look for serial NVRAM
1138 nvram:y test controllers for onboard seri 1138 nvram:y test controllers for onboard serial NVRAM
1139 ======= ================================= 1139 ======= =========================================
1140 1140
1141 This option can also been entered as an hexad 1141 This option can also been entered as an hexadecimal value that allows
1142 to control what information the driver will g 1142 to control what information the driver will get from the NVRAM and what
1143 information it will ignore. 1143 information it will ignore.
1144 For details see '17. Serial NVRAM support'. 1144 For details see '17. Serial NVRAM support'.
1145 1145
1146 When this option is enabled, the driver tries 1146 When this option is enabled, the driver tries to detect all boards using
1147 a Serial NVRAM. This memory is used to hold u 1147 a Serial NVRAM. This memory is used to hold user set up parameters.
1148 1148
1149 The parameters the driver is able to get from 1149 The parameters the driver is able to get from the NVRAM depend on the
1150 data format used, as follow: 1150 data format used, as follow:
1151 1151
1152 +-------------------------------+------------ 1152 +-------------------------------+------------------+--------------+
1153 | |Tekram forma 1153 | |Tekram format |Symbios format|
1154 +-------------------------------+------------ 1154 +-------------------------------+------------------+--------------+
1155 |General and host parameters | 1155 |General and host parameters | | |
1156 +-------------------------------+------------ 1156 +-------------------------------+------------------+--------------+
1157 | * Boot order | N 1157 | * Boot order | N | Y |
1158 +-------------------------------+------------ 1158 +-------------------------------+------------------+--------------+
1159 | * Host SCSI ID | Y 1159 | * Host SCSI ID | Y | Y |
1160 +-------------------------------+------------ 1160 +-------------------------------+------------------+--------------+
1161 | * SCSI parity checking | Y 1161 | * SCSI parity checking | Y | Y |
1162 +-------------------------------+------------ 1162 +-------------------------------+------------------+--------------+
1163 | * Verbose boot messages | N 1163 | * Verbose boot messages | N | Y |
1164 +-------------------------------+------------ 1164 +-------------------------------+------------------+--------------+
1165 |SCSI devices parameters 1165 |SCSI devices parameters |
1166 +-------------------------------+------------ 1166 +-------------------------------+------------------+--------------+
1167 | * Synchronous transfer speed | Y 1167 | * Synchronous transfer speed | Y | Y |
1168 +-------------------------------+------------ 1168 +-------------------------------+------------------+--------------+
1169 | * Wide 16 / Narrow | Y 1169 | * Wide 16 / Narrow | Y | Y |
1170 +-------------------------------+------------ 1170 +-------------------------------+------------------+--------------+
1171 | * Tagged Command Queuing | Y 1171 | * Tagged Command Queuing | Y | Y |
1172 | enabled | 1172 | enabled | | |
1173 +-------------------------------+------------ 1173 +-------------------------------+------------------+--------------+
1174 | * Disconnections enabled | Y 1174 | * Disconnections enabled | Y | Y |
1175 +-------------------------------+------------ 1175 +-------------------------------+------------------+--------------+
1176 | * Scan at boot time | N 1176 | * Scan at boot time | N | Y |
1177 +-------------------------------+------------ 1177 +-------------------------------+------------------+--------------+
1178 1178
1179 In order to speed up the system boot, for eac 1179 In order to speed up the system boot, for each device configured without
1180 the "scan at boot time" option, the driver fo 1180 the "scan at boot time" option, the driver forces an error on the
1181 first TEST UNIT READY command received for th 1181 first TEST UNIT READY command received for this device.
1182 1182
1183 Some SDMS BIOS revisions seem to be unable to 1183 Some SDMS BIOS revisions seem to be unable to boot cleanly with very fast
1184 hard disks. In such a situation you cannot co 1184 hard disks. In such a situation you cannot configure the NVRAM with
1185 optimized parameters value. 1185 optimized parameters value.
1186 1186
1187 The 'nvram' boot option can be entered in hex 1187 The 'nvram' boot option can be entered in hexadecimal form in order
1188 to ignore some options configured in the NVRA 1188 to ignore some options configured in the NVRAM, as follow:
1189 1189
1190 mvram=<bits options> 1190 mvram=<bits options>
1191 1191
1192 ==== ================================ 1192 ==== =================================================================
1193 0x01 look for NVRAM (equivalent to n 1193 0x01 look for NVRAM (equivalent to nvram=y)
1194 0x02 ignore NVRAM "Synchronous negoti 1194 0x02 ignore NVRAM "Synchronous negotiation" parameters for all devices
1195 0x04 ignore NVRAM "Wide negotiation" 1195 0x04 ignore NVRAM "Wide negotiation" parameter for all devices
1196 0x08 ignore NVRAM "Scan at boot time" 1196 0x08 ignore NVRAM "Scan at boot time" parameter for all devices
1197 0x80 also attach controllers set to O 1197 0x80 also attach controllers set to OFF in the NVRAM (sym53c8xx only)
1198 ==== ================================ 1198 ==== =================================================================
1199 1199
1200 Option 0x80 is only supported by the sym53c8x 1200 Option 0x80 is only supported by the sym53c8xx driver and is disabled by
1201 default. Result is that, by default (option n 1201 default. Result is that, by default (option not set), the sym53c8xx driver
1202 will not attach controllers set to OFF in the 1202 will not attach controllers set to OFF in the NVRAM.
1203 1203
1204 The ncr53c8xx always tries to attach all the 1204 The ncr53c8xx always tries to attach all the controllers. Option 0x80 has
1205 not been added to the ncr53c8xx driver, since 1205 not been added to the ncr53c8xx driver, since it has been reported to
1206 confuse users who use this driver since a lon 1206 confuse users who use this driver since a long time. If you desire a
1207 controller not to be attached by the ncr53c8x 1207 controller not to be attached by the ncr53c8xx driver at Linux boot, you
1208 must use the 'excl' driver boot option. 1208 must use the 'excl' driver boot option.
1209 1209
1210 10.6 SCSI BUS checking boot option. 1210 10.6 SCSI BUS checking boot option.
1211 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1211 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1212 1212
1213 When this option is set to a non-zero value, 1213 When this option is set to a non-zero value, the driver checks SCSI lines
1214 logic state, 100 micro-seconds after having a 1214 logic state, 100 micro-seconds after having asserted the SCSI RESET line.
1215 The driver just reads SCSI lines and checks a 1215 The driver just reads SCSI lines and checks all lines read FALSE except RESET.
1216 Since SCSI devices shall release the BUS at m 1216 Since SCSI devices shall release the BUS at most 800 nano-seconds after SCSI
1217 RESET has been asserted, any signal to TRUE m 1217 RESET has been asserted, any signal to TRUE may indicate a SCSI BUS problem.
1218 Unfortunately, the following common SCSI BUS 1218 Unfortunately, the following common SCSI BUS problems are not detected:
1219 1219
1220 - Only 1 terminator installed. 1220 - Only 1 terminator installed.
1221 - Misplaced terminators. 1221 - Misplaced terminators.
1222 - Bad quality terminators. 1222 - Bad quality terminators.
1223 1223
1224 On the other hand, either bad cabling, broken 1224 On the other hand, either bad cabling, broken devices, not conformant
1225 devices, ... may cause a SCSI signal to be wr 1225 devices, ... may cause a SCSI signal to be wrong when the driver reads it.
1226 1226
1227 10.7 IMMEDIATE ARBITRATION boot option 1227 10.7 IMMEDIATE ARBITRATION boot option
1228 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 1228 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
1229 1229
1230 This option is only supported by the SYM53C8X 1230 This option is only supported by the SYM53C8XX driver (not by the NCR53C8XX).
1231 1231
1232 SYMBIOS 53C8XX chips are able to arbitrate fo 1232 SYMBIOS 53C8XX chips are able to arbitrate for the SCSI BUS as soon as they
1233 have detected an expected disconnection (BUS 1233 have detected an expected disconnection (BUS FREE PHASE). For this process
1234 to be started, bit 1 of SCNTL1 IO register mu 1234 to be started, bit 1 of SCNTL1 IO register must be set when the chip is
1235 connected to the SCSI BUS. 1235 connected to the SCSI BUS.
1236 1236
1237 When this feature has been enabled for the cu 1237 When this feature has been enabled for the current connection, the chip has
1238 every chance to win arbitration if only devic 1238 every chance to win arbitration if only devices with lower priority are
1239 competing for the SCSI BUS. By the way, when 1239 competing for the SCSI BUS. By the way, when the chip is using SCSI id 7,
1240 then it will for sure win the next SCSI BUS a 1240 then it will for sure win the next SCSI BUS arbitration.
1241 1241
1242 Since, there is no way to know what devices a 1242 Since, there is no way to know what devices are trying to arbitrate for the
1243 BUS, using this feature can be extremely unfa 1243 BUS, using this feature can be extremely unfair. So, you are not advised
1244 to enable it, or at most enable this feature 1244 to enable it, or at most enable this feature for the case the chip lost
1245 the previous arbitration (boot option 'iarb:1 1245 the previous arbitration (boot option 'iarb:1').
1246 1246
1247 This feature has the following advantages: 1247 This feature has the following advantages:
1248 1248
1249 a) Allow the initiator with ID 7 to win arbit 1249 a) Allow the initiator with ID 7 to win arbitration when it wants so.
1250 b) Overlap at least 4 micro-seconds of arbitr 1250 b) Overlap at least 4 micro-seconds of arbitration time with the execution
1251 of SCRIPTS that deal with the end of the c 1251 of SCRIPTS that deal with the end of the current connection and that
1252 starts the next job. 1252 starts the next job.
1253 1253
1254 Hmmm... But (a) may just prevent other device 1254 Hmmm... But (a) may just prevent other devices from reselecting the initiator,
1255 and delay data transfers or status/completion 1255 and delay data transfers or status/completions, and (b) may just waste
1256 SCSI BUS bandwidth if the SCRIPTS execution l 1256 SCSI BUS bandwidth if the SCRIPTS execution lasts more than 4 micro-seconds.
1257 1257
1258 The use of IARB needs the SCSI_NCR_IARB_SUPPO 1258 The use of IARB needs the SCSI_NCR_IARB_SUPPORT option to have been defined
1259 at compile time and the 'iarb' boot option to 1259 at compile time and the 'iarb' boot option to have been set to a non zero
1260 value at boot time. It is not that useful for 1260 value at boot time. It is not that useful for real work, but can be used
1261 to stress SCSI devices or for some applicatio 1261 to stress SCSI devices or for some applications that can gain advantage of
1262 it. By the way, if you experience badnesses l 1262 it. By the way, if you experience badnesses like 'unexpected disconnections',
1263 'bad reselections', etc... when using IARB on 1263 'bad reselections', etc... when using IARB on heavy IO load, you should not
1264 be surprised, because force-feeding anything 1264 be surprised, because force-feeding anything and blocking its arse at the
1265 same time cannot work for a long time. :-)) 1265 same time cannot work for a long time. :-))
1266 1266
1267 1267
1268 11. Some constants and flags of the ncr53c8xx 1268 11. Some constants and flags of the ncr53c8xx.h header file
1269 ============================================= 1269 ===========================================================
1270 1270
1271 Some of these are defined from the configurat 1271 Some of these are defined from the configuration parameters. To
1272 change other "defines", you must edit the hea 1272 change other "defines", you must edit the header file. Do that only
1273 if you know what you are doing. 1273 if you know what you are doing.
1274 1274
1275 SCSI_NCR_SETUP_SPECIAL_FEATURES (default: def 1275 SCSI_NCR_SETUP_SPECIAL_FEATURES (default: defined)
1276 If defined, the driver will enable so 1276 If defined, the driver will enable some special features according
1277 to chip and revision id. 1277 to chip and revision id.
1278 1278
1279 For 810A, 860, 825A, 875 and 895 scsi 1279 For 810A, 860, 825A, 875 and 895 scsi chips, this option enables
1280 support of features that reduce load 1280 support of features that reduce load of PCI bus and memory accesses
1281 during scsi transfer processing: bur 1281 during scsi transfer processing: burst op-code fetch, read multiple,
1282 read line, prefetch, cache line, writ 1282 read line, prefetch, cache line, write and invalidate,
1283 burst 128 (875 only), large dma fifo 1283 burst 128 (875 only), large dma fifo (875 only), offset 16 (875 only).
1284 Can be changed by the following boot 1284 Can be changed by the following boot setup command::
1285 1285
1286 ncr53c8xx=specf:n 1286 ncr53c8xx=specf:n
1287 1287
1288 SCSI_NCR_IOMAPPED (default: not 1288 SCSI_NCR_IOMAPPED (default: not defined)
1289 If defined, normal I/O is forced. 1289 If defined, normal I/O is forced.
1290 1290
1291 SCSI_NCR_SHARE_IRQ (default: def 1291 SCSI_NCR_SHARE_IRQ (default: defined)
1292 If defined, request shared IRQ. 1292 If defined, request shared IRQ.
1293 1293
1294 SCSI_NCR_MAX_TAGS (default: 8) 1294 SCSI_NCR_MAX_TAGS (default: 8)
1295 Maximum number of simultaneous tagged 1295 Maximum number of simultaneous tagged commands to a device.
1296 1296
1297 Can be changed by "settags <target> < 1297 Can be changed by "settags <target> <maxtags>"
1298 1298
1299 SCSI_NCR_SETUP_DEFAULT_SYNC (default: 50) 1299 SCSI_NCR_SETUP_DEFAULT_SYNC (default: 50)
1300 Transfer period factor the driver wil 1300 Transfer period factor the driver will use at boot time for synchronous
1301 negotiation. 0 means asynchronous. 1301 negotiation. 0 means asynchronous.
1302 1302
1303 Can be changed by "setsync <target> < 1303 Can be changed by "setsync <target> <period factor>"
1304 1304
1305 SCSI_NCR_SETUP_DEFAULT_TAGS (default: 8) 1305 SCSI_NCR_SETUP_DEFAULT_TAGS (default: 8)
1306 Default number of simultaneous tagged 1306 Default number of simultaneous tagged commands to a device.
1307 1307
1308 < 1 means tagged command queuing disa 1308 < 1 means tagged command queuing disabled at start-up.
1309 1309
1310 SCSI_NCR_ALWAYS_SIMPLE_TAG (default: def 1310 SCSI_NCR_ALWAYS_SIMPLE_TAG (default: defined)
1311 Use SIMPLE TAG for read and write com 1311 Use SIMPLE TAG for read and write commands.
1312 1312
1313 Can be changed by "setorder <ordered| 1313 Can be changed by "setorder <ordered|simple|default>"
1314 1314
1315 SCSI_NCR_SETUP_DISCONNECTION (default: def 1315 SCSI_NCR_SETUP_DISCONNECTION (default: defined)
1316 If defined, targets are allowed to di 1316 If defined, targets are allowed to disconnect.
1317 1317
1318 SCSI_NCR_SETUP_FORCE_SYNC_NEGO (default: not 1318 SCSI_NCR_SETUP_FORCE_SYNC_NEGO (default: not defined)
1319 If defined, synchronous negotiation i 1319 If defined, synchronous negotiation is tried for all SCSI-2 devices.
1320 1320
1321 Can be changed by "setsync <target> < 1321 Can be changed by "setsync <target> <period>"
1322 1322
1323 SCSI_NCR_SETUP_MASTER_PARITY (default: def 1323 SCSI_NCR_SETUP_MASTER_PARITY (default: defined)
1324 If defined, master parity checking is 1324 If defined, master parity checking is enabled.
1325 1325
1326 SCSI_NCR_SETUP_SCSI_PARITY (default: def 1326 SCSI_NCR_SETUP_SCSI_PARITY (default: defined)
1327 If defined, SCSI parity checking is e 1327 If defined, SCSI parity checking is enabled.
1328 1328
1329 SCSI_NCR_PROFILE_SUPPORT (default: not 1329 SCSI_NCR_PROFILE_SUPPORT (default: not defined)
1330 If defined, profiling information is 1330 If defined, profiling information is gathered.
1331 1331
1332 SCSI_NCR_MAX_SCATTER (default: 128 1332 SCSI_NCR_MAX_SCATTER (default: 128)
1333 Scatter list size of the driver ccb. 1333 Scatter list size of the driver ccb.
1334 1334
1335 SCSI_NCR_MAX_TARGET (default: 16) 1335 SCSI_NCR_MAX_TARGET (default: 16)
1336 Max number of targets per host. 1336 Max number of targets per host.
1337 1337
1338 SCSI_NCR_MAX_HOST (default: 2) 1338 SCSI_NCR_MAX_HOST (default: 2)
1339 Max number of host controllers. 1339 Max number of host controllers.
1340 1340
1341 SCSI_NCR_SETTLE_TIME (default: 2) 1341 SCSI_NCR_SETTLE_TIME (default: 2)
1342 Number of seconds the driver will wai 1342 Number of seconds the driver will wait after reset.
1343 1343
1344 SCSI_NCR_TIMEOUT_ALERT (default: 3) 1344 SCSI_NCR_TIMEOUT_ALERT (default: 3)
1345 If a pending command will time out af 1345 If a pending command will time out after this amount of seconds,
1346 an ordered tag is used for the next c 1346 an ordered tag is used for the next command.
1347 1347
1348 Avoids timeouts for unordered tagged 1348 Avoids timeouts for unordered tagged commands.
1349 1349
1350 SCSI_NCR_CAN_QUEUE (default: 7*S 1350 SCSI_NCR_CAN_QUEUE (default: 7*SCSI_NCR_MAX_TAGS)
1351 Max number of commands that can be qu 1351 Max number of commands that can be queued to a host.
1352 1352
1353 SCSI_NCR_CMD_PER_LUN (default: SCS 1353 SCSI_NCR_CMD_PER_LUN (default: SCSI_NCR_MAX_TAGS)
1354 Max number of commands queued to a ho 1354 Max number of commands queued to a host for a device.
1355 1355
1356 SCSI_NCR_SG_TABLESIZE (default: SCS 1356 SCSI_NCR_SG_TABLESIZE (default: SCSI_NCR_MAX_SCATTER-1)
1357 Max size of the Linux scatter/gather 1357 Max size of the Linux scatter/gather list.
1358 1358
1359 SCSI_NCR_MAX_LUN (default: 8) 1359 SCSI_NCR_MAX_LUN (default: 8)
1360 Max number of LUNs per target. 1360 Max number of LUNs per target.
1361 1361
1362 1362
1363 12. Installation 1363 12. Installation
1364 ================ 1364 ================
1365 1365
1366 This driver is part of the linux kernel distr 1366 This driver is part of the linux kernel distribution.
1367 Driver files are located in the sub-directory 1367 Driver files are located in the sub-directory "drivers/scsi" of the
1368 kernel source tree. 1368 kernel source tree.
1369 1369
1370 Driver files:: 1370 Driver files::
1371 1371
1372 README.ncr53c8xx : this file 1372 README.ncr53c8xx : this file
1373 ChangeLog.ncr53c8xx : change log 1373 ChangeLog.ncr53c8xx : change log
1374 ncr53c8xx.h : definitions 1374 ncr53c8xx.h : definitions
1375 ncr53c8xx.c : the driver 1375 ncr53c8xx.c : the driver code
1376 1376
1377 New driver versions are made available separa 1377 New driver versions are made available separately in order to allow testing
1378 changes and new features prior to including t 1378 changes and new features prior to including them into the linux kernel
1379 distribution. The following URL provides info 1379 distribution. The following URL provides information on latest available
1380 patches: 1380 patches:
1381 1381
1382 ftp://ftp.tux.org/pub/people/gerard-rou 1382 ftp://ftp.tux.org/pub/people/gerard-roudier/README
1383 1383
1384 1384
1385 13. Architecture dependent features 1385 13. Architecture dependent features
1386 =================================== 1386 ===================================
1387 1387
1388 <Not yet written> 1388 <Not yet written>
1389 1389
1390 1390
1391 14. Known problems 1391 14. Known problems
1392 ================== 1392 ==================
1393 1393
1394 14.1 Tagged commands with Iomega Jaz device 1394 14.1 Tagged commands with Iomega Jaz device
1395 ------------------------------------------- 1395 -------------------------------------------
1396 1396
1397 I have not tried this device, however it has 1397 I have not tried this device, however it has been reported to me the
1398 following: This device is capable of Tagged c 1398 following: This device is capable of Tagged command queuing. However
1399 while spinning up, it rejects Tagged commands 1399 while spinning up, it rejects Tagged commands. This behaviour is
1400 conforms to 6.8.2 of SCSI-2 specifications. T 1400 conforms to 6.8.2 of SCSI-2 specifications. The current behaviour of
1401 the driver in that situation is not satisfyin 1401 the driver in that situation is not satisfying. So do not enable
1402 Tagged command queuing for devices that are a 1402 Tagged command queuing for devices that are able to spin down. The
1403 other problem that may appear is timeouts. Th 1403 other problem that may appear is timeouts. The only way to avoid
1404 timeouts seems to edit linux/drivers/scsi/sd. 1404 timeouts seems to edit linux/drivers/scsi/sd.c and to increase the
1405 current timeout values. 1405 current timeout values.
1406 1406
1407 14.2 Device names change when another control 1407 14.2 Device names change when another controller is added
1408 --------------------------------------------- 1408 ---------------------------------------------------------
1409 1409
1410 When you add a new NCR53C8XX chip based contr 1410 When you add a new NCR53C8XX chip based controller to a system that already
1411 has one or more controllers of this family, i 1411 has one or more controllers of this family, it may happen that the order
1412 the driver registers them to the kernel cause 1412 the driver registers them to the kernel causes problems due to device
1413 name changes. 1413 name changes.
1414 When at least one controller uses NvRAM, SDMS 1414 When at least one controller uses NvRAM, SDMS BIOS version 4 allows you to
1415 define the order the BIOS will scan the scsi 1415 define the order the BIOS will scan the scsi boards. The driver attaches
1416 controllers according to BIOS information if 1416 controllers according to BIOS information if NvRAM detect option is set.
1417 1417
1418 If your controllers do not have NvRAM, you ca 1418 If your controllers do not have NvRAM, you can:
1419 1419
1420 - Ask the driver to probe chip ids in reverse 1420 - Ask the driver to probe chip ids in reverse order from the boot command
1421 line: ncr53c8xx=revprob:y 1421 line: ncr53c8xx=revprob:y
1422 - Make appropriate changes in the fstab. 1422 - Make appropriate changes in the fstab.
1423 - Use the 'scsidev' tool from Eric Youngdale. 1423 - Use the 'scsidev' tool from Eric Youngdale.
1424 1424
1425 14.3 Using only 8 bit devices with a WIDE SCS 1425 14.3 Using only 8 bit devices with a WIDE SCSI controller
1426 --------------------------------------------- 1426 ---------------------------------------------------------
1427 1427
1428 When only 8 bit NARROW devices are connected 1428 When only 8 bit NARROW devices are connected to a 16 bit WIDE SCSI controller,
1429 you must ensure that lines of the wide part o 1429 you must ensure that lines of the wide part of the SCSI BUS are pulled-up.
1430 This can be achieved by ENABLING the WIDE TER 1430 This can be achieved by ENABLING the WIDE TERMINATOR portion of the SCSI
1431 controller card. 1431 controller card.
1432 1432
1433 The TYAN 1365 documentation revision 1.2 is n 1433 The TYAN 1365 documentation revision 1.2 is not correct about such settings.
1434 (page 10, figure 3.3). 1434 (page 10, figure 3.3).
1435 1435
1436 14.4 Possible data corruption during a Memory 1436 14.4 Possible data corruption during a Memory Write and Invalidate
1437 --------------------------------------------- 1437 ------------------------------------------------------------------
1438 1438
1439 This problem is described in SYMBIOS DEL 397, 1439 This problem is described in SYMBIOS DEL 397, Part Number 69-039241, ITEM 4.
1440 1440
1441 In some complex situations, 53C875 chips revi 1441 In some complex situations, 53C875 chips revision <= 3 may start a PCI
1442 Write and Invalidate Command at a not cache-l 1442 Write and Invalidate Command at a not cache-line-aligned 4 DWORDS boundary.
1443 This is only possible when Cache Line Size is 1443 This is only possible when Cache Line Size is 8 DWORDS or greater.
1444 Pentium systems use a 8 DWORDS cache line siz 1444 Pentium systems use a 8 DWORDS cache line size and so are concerned by
1445 this chip bug, unlike i486 systems that use a 1445 this chip bug, unlike i486 systems that use a 4 DWORDS cache line size.
1446 1446
1447 When this situation occurs, the chip may comp 1447 When this situation occurs, the chip may complete the Write and Invalidate
1448 command after having only filled part of the 1448 command after having only filled part of the last cache line involved in
1449 the transfer, leaving to data corruption the 1449 the transfer, leaving to data corruption the remainder of this cache line.
1450 1450
1451 Not using Write And Invalidate obviously gets 1451 Not using Write And Invalidate obviously gets rid of this chip bug, and so
1452 it is now the default setting of the driver. 1452 it is now the default setting of the driver.
1453 However, for people like me who want to enabl 1453 However, for people like me who want to enable this feature, I have added
1454 part of a work-around suggested by SYMBIOS. T 1454 part of a work-around suggested by SYMBIOS. This work-around resets the
1455 addressing logic when the DATA IN phase is en 1455 addressing logic when the DATA IN phase is entered and so prevents the bug
1456 from being triggered for the first SCSI MOVE 1456 from being triggered for the first SCSI MOVE of the phase. This work-around
1457 should be enough according to the following: 1457 should be enough according to the following:
1458 1458
1459 The only driver internal data structure that 1459 The only driver internal data structure that is greater than 8 DWORDS and
1460 that is moved by the SCRIPTS processor is the 1460 that is moved by the SCRIPTS processor is the 'CCB header' that contains
1461 the context of the SCSI transfer. This data s 1461 the context of the SCSI transfer. This data structure is aligned on 8 DWORDS
1462 boundary (Pentium Cache Line Size), and so is 1462 boundary (Pentium Cache Line Size), and so is immune to this chip bug, at
1463 least on Pentium systems. 1463 least on Pentium systems.
1464 1464
1465 But the conditions of this bug can be met whe 1465 But the conditions of this bug can be met when a SCSI read command is
1466 performed using a buffer that is 4 DWORDS but 1466 performed using a buffer that is 4 DWORDS but not cache-line aligned.
1467 This cannot happen under Linux when scatter/g 1467 This cannot happen under Linux when scatter/gather lists are used since
1468 they only refer to system buffers that are we 1468 they only refer to system buffers that are well aligned. So, a work around
1469 may only be needed under Linux when a scatter 1469 may only be needed under Linux when a scatter/gather list is not used and
1470 when the SCSI DATA IN phase is reentered afte 1470 when the SCSI DATA IN phase is reentered after a phase mismatch.
1471 1471
1472 15. SCSI problem troubleshooting 1472 15. SCSI problem troubleshooting
1473 ================================ 1473 ================================
1474 1474
1475 15.1 Problem tracking 1475 15.1 Problem tracking
1476 --------------------- 1476 ---------------------
1477 1477
1478 Most SCSI problems are due to a non conforman 1478 Most SCSI problems are due to a non conformant SCSI bus or to buggy
1479 devices. If unfortunately you have SCSI prob 1479 devices. If unfortunately you have SCSI problems, you can check the
1480 following things: 1480 following things:
1481 1481
1482 - SCSI bus cables 1482 - SCSI bus cables
1483 - terminations at both end of the SCSI chain 1483 - terminations at both end of the SCSI chain
1484 - linux syslog messages (some of them may hel 1484 - linux syslog messages (some of them may help you)
1485 1485
1486 If you do not find the source of problems, yo 1486 If you do not find the source of problems, you can configure the
1487 driver with no features enabled. 1487 driver with no features enabled.
1488 1488
1489 - only asynchronous data transfers 1489 - only asynchronous data transfers
1490 - tagged commands disabled 1490 - tagged commands disabled
1491 - disconnections not allowed 1491 - disconnections not allowed
1492 1492
1493 Now, if your SCSI bus is ok, your system have 1493 Now, if your SCSI bus is ok, your system have every chance to work
1494 with this safe configuration but performances 1494 with this safe configuration but performances will not be optimal.
1495 1495
1496 If it still fails, then you can send your pro 1496 If it still fails, then you can send your problem description to
1497 appropriate mailing lists or news-groups. Se 1497 appropriate mailing lists or news-groups. Send me a copy in order to
1498 be sure I will receive it. Obviously, a bug 1498 be sure I will receive it. Obviously, a bug in the driver code is
1499 possible. 1499 possible.
1500 1500
1501 My email address: Gerard Roudier <groudie 1501 My email address: Gerard Roudier <groudier@free.fr>
1502 1502
1503 Allowing disconnections is important if you u 1503 Allowing disconnections is important if you use several devices on
1504 your SCSI bus but often causes problems with 1504 your SCSI bus but often causes problems with buggy devices.
1505 Synchronous data transfers increases throughp 1505 Synchronous data transfers increases throughput of fast devices like
1506 hard disks. Good SCSI hard disks with a larg 1506 hard disks. Good SCSI hard disks with a large cache gain advantage of
1507 tagged commands queuing. 1507 tagged commands queuing.
1508 1508
1509 Try to enable one feature at a time with cont 1509 Try to enable one feature at a time with control commands. For example:
1510 1510
1511 :: 1511 ::
1512 1512
1513 echo "setsync all 25" >/proc/scsi/ncr53c8 1513 echo "setsync all 25" >/proc/scsi/ncr53c8xx/0
1514 1514
1515 Will enable fast synchronous data transfer ne 1515 Will enable fast synchronous data transfer negotiation for all targets.
1516 1516
1517 :: 1517 ::
1518 1518
1519 echo "setflag 3" >/proc/scsi/ncr53c8xx/0 1519 echo "setflag 3" >/proc/scsi/ncr53c8xx/0
1520 1520
1521 Will reset flags (no_disc) for target 3, and 1521 Will reset flags (no_disc) for target 3, and so will allow it to disconnect
1522 the SCSI Bus. 1522 the SCSI Bus.
1523 1523
1524 :: 1524 ::
1525 1525
1526 echo "settags 3 8" >/proc/scsi/ncr53c8xx/ 1526 echo "settags 3 8" >/proc/scsi/ncr53c8xx/0
1527 1527
1528 Will enable tagged command queuing for target 1528 Will enable tagged command queuing for target 3 if that device supports it.
1529 1529
1530 Once you have found the device and the featur 1530 Once you have found the device and the feature that cause problems, just
1531 disable that feature for that device. 1531 disable that feature for that device.
1532 1532
1533 15.2 Understanding hardware error reports 1533 15.2 Understanding hardware error reports
1534 ----------------------------------------- 1534 -----------------------------------------
1535 1535
1536 When the driver detects an unexpected error c 1536 When the driver detects an unexpected error condition, it may display a
1537 message of the following pattern:: 1537 message of the following pattern::
1538 1538
1539 sym53c876-0:1: ERROR (0:48) (1-21-65) (f/ 1539 sym53c876-0:1: ERROR (0:48) (1-21-65) (f/95) @ (script 7c0:19000000).
1540 sym53c876-0: script cmd = 19000000 1540 sym53c876-0: script cmd = 19000000
1541 sym53c876-0: regdump: da 10 80 95 47 0f 0 1541 sym53c876-0: regdump: da 10 80 95 47 0f 01 07 75 01 81 21 80 01 09 00.
1542 1542
1543 Some fields in such a message may help you un 1543 Some fields in such a message may help you understand the cause of the
1544 problem, as follows:: 1544 problem, as follows::
1545 1545
1546 sym53c876-0:1: ERROR (0:48) (1-21-65) (f/ 1546 sym53c876-0:1: ERROR (0:48) (1-21-65) (f/95) @ (script 7c0:19000000).
1547 ............A.........B.C....D.E..F....G. 1547 ............A.........B.C....D.E..F....G.H.......I.....J...K.......
1548 1548
1549 Field A : target number. 1549 Field A : target number.
1550 SCSI ID of the device the controller was ta 1550 SCSI ID of the device the controller was talking with at the moment the
1551 error occurs. 1551 error occurs.
1552 1552
1553 Field B : DSTAT io register (DMA STATUS) 1553 Field B : DSTAT io register (DMA STATUS)
1554 ======== ================================ 1554 ======== =============================================================
1555 Bit 0x40 MDPE Master Data Parity Error 1555 Bit 0x40 MDPE Master Data Parity Error
1556 Data parity error detected on th 1556 Data parity error detected on the PCI BUS.
1557 Bit 0x20 BF Bus Fault 1557 Bit 0x20 BF Bus Fault
1558 PCI bus fault condition detected 1558 PCI bus fault condition detected
1559 Bit 0x01 IID Illegal Instruction Detecte 1559 Bit 0x01 IID Illegal Instruction Detected
1560 Set by the chip when it detects 1560 Set by the chip when it detects an Illegal Instruction format
1561 on some condition that makes an 1561 on some condition that makes an instruction illegal.
1562 Bit 0x80 DFE Dma Fifo Empty 1562 Bit 0x80 DFE Dma Fifo Empty
1563 Pure status bit that does not in 1563 Pure status bit that does not indicate an error.
1564 ======== ================================ 1564 ======== =============================================================
1565 1565
1566 If the reported DSTAT value contains a comb 1566 If the reported DSTAT value contains a combination of MDPE (0x40),
1567 BF (0x20), then the cause may be likely due 1567 BF (0x20), then the cause may be likely due to a PCI BUS problem.
1568 1568
1569 Field C : SIST io register (SCSI Interrupt St 1569 Field C : SIST io register (SCSI Interrupt Status)
1570 ======== ================================ 1570 ======== ==================================================================
1571 Bit 0x08 SGE SCSI GROSS ERROR 1571 Bit 0x08 SGE SCSI GROSS ERROR
1572 Indicates that the chip detected 1572 Indicates that the chip detected a severe error condition
1573 on the SCSI BUS that prevents th 1573 on the SCSI BUS that prevents the SCSI protocol from functioning
1574 properly. 1574 properly.
1575 Bit 0x04 UDC Unexpected Disconnection 1575 Bit 0x04 UDC Unexpected Disconnection
1576 Indicates that the device releas 1576 Indicates that the device released the SCSI BUS when the chip
1577 was not expecting this to happen 1577 was not expecting this to happen. A device may behave so to
1578 indicate the SCSI initiator that 1578 indicate the SCSI initiator that an error condition not reportable
1579 using the SCSI protocol has occu 1579 using the SCSI protocol has occurred.
1580 Bit 0x02 RST SCSI BUS Reset 1580 Bit 0x02 RST SCSI BUS Reset
1581 Generally SCSI targets do not re 1581 Generally SCSI targets do not reset the SCSI BUS, although any
1582 device on the BUS can reset it a 1582 device on the BUS can reset it at any time.
1583 Bit 0x01 PAR Parity 1583 Bit 0x01 PAR Parity
1584 SCSI parity error detected. 1584 SCSI parity error detected.
1585 ======== ================================ 1585 ======== ==================================================================
1586 1586
1587 On a faulty SCSI BUS, any error condition a 1587 On a faulty SCSI BUS, any error condition among SGE (0x08), UDC (0x04) and
1588 PAR (0x01) may be detected by the chip. If 1588 PAR (0x01) may be detected by the chip. If your SCSI system sometimes
1589 encounters such error conditions, especiall 1589 encounters such error conditions, especially SCSI GROSS ERROR, then a SCSI
1590 BUS problem is likely the cause of these er 1590 BUS problem is likely the cause of these errors.
1591 1591
1592 For fields D,E,F,G and H, you may look into t 1592 For fields D,E,F,G and H, you may look into the sym53c8xx_defs.h file
1593 that contains some minimal comments on IO reg 1593 that contains some minimal comments on IO register bits.
1594 1594
1595 Field D : SOCL Scsi Output Control Latch 1595 Field D : SOCL Scsi Output Control Latch
1596 This register reflects the state of 1596 This register reflects the state of the SCSI control lines the
1597 chip want to drive or compare again 1597 chip want to drive or compare against.
1598 1598
1599 Field E : SBCL Scsi Bus Control Lines 1599 Field E : SBCL Scsi Bus Control Lines
1600 Actual value of control lines on th 1600 Actual value of control lines on the SCSI BUS.
1601 1601
1602 Field F : SBDL Scsi Bus Data Lines 1602 Field F : SBDL Scsi Bus Data Lines
1603 Actual value of data lines on the S 1603 Actual value of data lines on the SCSI BUS.
1604 1604
1605 Field G : SXFER SCSI Transfer 1605 Field G : SXFER SCSI Transfer
1606 Contains the setting of the Synchro 1606 Contains the setting of the Synchronous Period for output and
1607 the current Synchronous offset (off 1607 the current Synchronous offset (offset 0 means asynchronous).
1608 1608
1609 Field H : SCNTL3 Scsi Control Register 3 1609 Field H : SCNTL3 Scsi Control Register 3
1610 Contains the setting of timing valu 1610 Contains the setting of timing values for both asynchronous and
1611 synchronous data transfers. 1611 synchronous data transfers.
1612 1612
1613 Understanding Fields I, J, K and dumps requir 1613 Understanding Fields I, J, K and dumps requires to have good knowledge of
1614 SCSI standards, chip cores functionnals and i 1614 SCSI standards, chip cores functionnals and internal driver data structures.
1615 You are not required to decode and understand 1615 You are not required to decode and understand them, unless you want to help
1616 maintain the driver code. 1616 maintain the driver code.
1617 1617
1618 16. Synchronous transfer negotiation tables 1618 16. Synchronous transfer negotiation tables
1619 =========================================== 1619 ===========================================
1620 1620
1621 Tables below have been created by calling the 1621 Tables below have been created by calling the routine the driver uses
1622 for synchronisation negotiation timing calcul 1622 for synchronisation negotiation timing calculation and chip setting.
1623 The first table corresponds to Ultra chips 53 1623 The first table corresponds to Ultra chips 53875 and 53C860 with 80 MHz
1624 clock and 5 clock divisors. 1624 clock and 5 clock divisors.
1625 The second one has been calculated by setting 1625 The second one has been calculated by setting the scsi clock to 40 Mhz
1626 and using 4 clock divisors and so applies to 1626 and using 4 clock divisors and so applies to all NCR53C8XX chips in fast
1627 SCSI-2 mode. 1627 SCSI-2 mode.
1628 1628
1629 Periods are in nano-seconds and speeds are in 1629 Periods are in nano-seconds and speeds are in Mega-transfers per second.
1630 1 Mega-transfers/second means 1 MB/s with 8 b 1630 1 Mega-transfers/second means 1 MB/s with 8 bits SCSI and 2 MB/s with
1631 Wide16 SCSI. 1631 Wide16 SCSI.
1632 1632
1633 16.1 Synchronous timings for 53C895, 53C875 a 1633 16.1 Synchronous timings for 53C895, 53C875 and 53C860 SCSI controllers
1634 1634
1635 +-----------------------------+--------+----- 1635 +-----------------------------+--------+-------+--------------+
1636 |Negotiated |NCR settings 1636 |Negotiated |NCR settings | |
1637 +-------+--------+------------+--------+----- 1637 +-------+--------+------------+--------+-------+ |
1638 |Factor |Period |Speed |Period |Speed 1638 |Factor |Period |Speed |Period |Speed | |
1639 +-------+--------+------------+--------+----- 1639 +-------+--------+------------+--------+-------+--------------+
1640 |10 | 25 |40.000 | 25 |40.00 1640 |10 | 25 |40.000 | 25 |40.000 | (53C895 only)|
1641 +-------+--------+------------+--------+----- 1641 +-------+--------+------------+--------+-------+--------------+
1642 |11 | 30.2 |33.112 | 31.25 |32.00 1642 |11 | 30.2 |33.112 | 31.25 |32.000 | (53C895 only)|
1643 +-------+--------+------------+--------+----- 1643 +-------+--------+------------+--------+-------+--------------+
1644 |12 | 50 |20.000 | 50 |20.00 1644 |12 | 50 |20.000 | 50 |20.000 | |
1645 +-------+--------+------------+--------+----- 1645 +-------+--------+------------+--------+-------+--------------+
1646 |13 | 52 |19.230 | 62 |16.00 1646 |13 | 52 |19.230 | 62 |16.000 | |
1647 +-------+--------+------------+--------+----- 1647 +-------+--------+------------+--------+-------+--------------+
1648 |14 | 56 |17.857 | 62 |16.00 1648 |14 | 56 |17.857 | 62 |16.000 | |
1649 +-------+--------+------------+--------+----- 1649 +-------+--------+------------+--------+-------+--------------+
1650 |15 | 60 |16.666 | 62 |16.00 1650 |15 | 60 |16.666 | 62 |16.000 | |
1651 +-------+--------+------------+--------+----- 1651 +-------+--------+------------+--------+-------+--------------+
1652 |16 | 64 |15.625 | 75 |13.33 1652 |16 | 64 |15.625 | 75 |13.333 | |
1653 +-------+--------+------------+--------+----- 1653 +-------+--------+------------+--------+-------+--------------+
1654 |17 | 68 |14.705 | 75 |13.33 1654 |17 | 68 |14.705 | 75 |13.333 | |
1655 +-------+--------+------------+--------+----- 1655 +-------+--------+------------+--------+-------+--------------+
1656 |18 | 72 |13.888 | 75 |13.33 1656 |18 | 72 |13.888 | 75 |13.333 | |
1657 +-------+--------+------------+--------+----- 1657 +-------+--------+------------+--------+-------+--------------+
1658 |19 | 76 |13.157 | 87 |11.42 1658 |19 | 76 |13.157 | 87 |11.428 | |
1659 +-------+--------+------------+--------+----- 1659 +-------+--------+------------+--------+-------+--------------+
1660 |20 | 80 |12.500 | 87 |11.42 1660 |20 | 80 |12.500 | 87 |11.428 | |
1661 +-------+--------+------------+--------+----- 1661 +-------+--------+------------+--------+-------+--------------+
1662 |21 | 84 |11.904 | 87 |11.42 1662 |21 | 84 |11.904 | 87 |11.428 | |
1663 +-------+--------+------------+--------+----- 1663 +-------+--------+------------+--------+-------+--------------+
1664 |22 | 88 |11.363 | 93 |10.66 1664 |22 | 88 |11.363 | 93 |10.666 | |
1665 +-------+--------+------------+--------+----- 1665 +-------+--------+------------+--------+-------+--------------+
1666 |23 | 92 |10.869 | 93 |10.66 1666 |23 | 92 |10.869 | 93 |10.666 | |
1667 +-------+--------+------------+--------+----- 1667 +-------+--------+------------+--------+-------+--------------+
1668 |24 | 96 |10.416 |100 |10.00 1668 |24 | 96 |10.416 |100 |10.000 | |
1669 +-------+--------+------------+--------+----- 1669 +-------+--------+------------+--------+-------+--------------+
1670 |25 |100 |10.000 |100 |10.00 1670 |25 |100 |10.000 |100 |10.000 | |
1671 +-------+--------+------------+--------+----- 1671 +-------+--------+------------+--------+-------+--------------+
1672 |26 |104 | 9.615 |112 | 8.88 1672 |26 |104 | 9.615 |112 | 8.888 | |
1673 +-------+--------+------------+--------+----- 1673 +-------+--------+------------+--------+-------+--------------+
1674 |27 |108 | 9.259 |112 | 8.88 1674 |27 |108 | 9.259 |112 | 8.888 | |
1675 +-------+--------+------------+--------+----- 1675 +-------+--------+------------+--------+-------+--------------+
1676 |28 |112 | 8.928 |112 | 8.88 1676 |28 |112 | 8.928 |112 | 8.888 | |
1677 +-------+--------+------------+--------+----- 1677 +-------+--------+------------+--------+-------+--------------+
1678 |29 |116 | 8.620 |125 | 8.00 1678 |29 |116 | 8.620 |125 | 8.000 | |
1679 +-------+--------+------------+--------+----- 1679 +-------+--------+------------+--------+-------+--------------+
1680 |30 |120 | 8.333 |125 | 8.00 1680 |30 |120 | 8.333 |125 | 8.000 | |
1681 +-------+--------+------------+--------+----- 1681 +-------+--------+------------+--------+-------+--------------+
1682 |31 |124 | 8.064 |125 | 8.00 1682 |31 |124 | 8.064 |125 | 8.000 | |
1683 +-------+--------+------------+--------+----- 1683 +-------+--------+------------+--------+-------+--------------+
1684 |32 |128 | 7.812 |131 | 7.61 1684 |32 |128 | 7.812 |131 | 7.619 | |
1685 +-------+--------+------------+--------+----- 1685 +-------+--------+------------+--------+-------+--------------+
1686 |33 |132 | 7.575 |150 | 6.66 1686 |33 |132 | 7.575 |150 | 6.666 | |
1687 +-------+--------+------------+--------+----- 1687 +-------+--------+------------+--------+-------+--------------+
1688 |34 |136 | 7.352 |150 | 6.66 1688 |34 |136 | 7.352 |150 | 6.666 | |
1689 +-------+--------+------------+--------+----- 1689 +-------+--------+------------+--------+-------+--------------+
1690 |35 |140 | 7.142 |150 | 6.66 1690 |35 |140 | 7.142 |150 | 6.666 | |
1691 +-------+--------+------------+--------+----- 1691 +-------+--------+------------+--------+-------+--------------+
1692 |36 |144 | 6.944 |150 | 6.66 1692 |36 |144 | 6.944 |150 | 6.666 | |
1693 +-------+--------+------------+--------+----- 1693 +-------+--------+------------+--------+-------+--------------+
1694 |37 |148 | 6.756 |150 | 6.66 1694 |37 |148 | 6.756 |150 | 6.666 | |
1695 +-------+--------+------------+--------+----- 1695 +-------+--------+------------+--------+-------+--------------+
1696 |38 |152 | 6.578 |175 | 5.71 1696 |38 |152 | 6.578 |175 | 5.714 | |
1697 +-------+--------+------------+--------+----- 1697 +-------+--------+------------+--------+-------+--------------+
1698 |39 |156 | 6.410 |175 | 5.71 1698 |39 |156 | 6.410 |175 | 5.714 | |
1699 +-------+--------+------------+--------+----- 1699 +-------+--------+------------+--------+-------+--------------+
1700 |40 |160 | 6.250 |175 | 5.71 1700 |40 |160 | 6.250 |175 | 5.714 | |
1701 +-------+--------+------------+--------+----- 1701 +-------+--------+------------+--------+-------+--------------+
1702 |41 |164 | 6.097 |175 | 5.71 1702 |41 |164 | 6.097 |175 | 5.714 | |
1703 +-------+--------+------------+--------+----- 1703 +-------+--------+------------+--------+-------+--------------+
1704 |42 |168 | 5.952 |175 | 5.71 1704 |42 |168 | 5.952 |175 | 5.714 | |
1705 +-------+--------+------------+--------+----- 1705 +-------+--------+------------+--------+-------+--------------+
1706 |43 |172 | 5.813 |175 | 5.71 1706 |43 |172 | 5.813 |175 | 5.714 | |
1707 +-------+--------+------------+--------+----- 1707 +-------+--------+------------+--------+-------+--------------+
1708 |44 |176 | 5.681 |187 | 5.33 1708 |44 |176 | 5.681 |187 | 5.333 | |
1709 +-------+--------+------------+--------+----- 1709 +-------+--------+------------+--------+-------+--------------+
1710 |45 |180 | 5.555 |187 | 5.33 1710 |45 |180 | 5.555 |187 | 5.333 | |
1711 +-------+--------+------------+--------+----- 1711 +-------+--------+------------+--------+-------+--------------+
1712 |46 |184 | 5.434 |187 | 5.33 1712 |46 |184 | 5.434 |187 | 5.333 | |
1713 +-------+--------+------------+--------+----- 1713 +-------+--------+------------+--------+-------+--------------+
1714 |47 |188 | 5.319 |200 | 5.00 1714 |47 |188 | 5.319 |200 | 5.000 | |
1715 +-------+--------+------------+--------+----- 1715 +-------+--------+------------+--------+-------+--------------+
1716 |48 |192 | 5.208 |200 | 5.00 1716 |48 |192 | 5.208 |200 | 5.000 | |
1717 +-------+--------+------------+--------+----- 1717 +-------+--------+------------+--------+-------+--------------+
1718 |49 |196 | 5.102 |200 | 5.00 1718 |49 |196 | 5.102 |200 | 5.000 | |
1719 +-------+--------+------------+--------+----- 1719 +-------+--------+------------+--------+-------+--------------+
1720 1720
1721 16.2 Synchronous timings for fast SCSI-2 53C8 1721 16.2 Synchronous timings for fast SCSI-2 53C8XX controllers
1722 1722
1723 +-----------------------------+-------------- 1723 +-----------------------------+----------------+
1724 |Negotiated |NCR settings 1724 |Negotiated |NCR settings |
1725 +-------+--------+------------+--------+----- 1725 +-------+--------+------------+--------+-------+
1726 |Factor |Period |Speed |Period |Speed 1726 |Factor |Period |Speed |Period |Speed |
1727 +-------+--------+------------+--------+----- 1727 +-------+--------+------------+--------+-------+
1728 |25 |100 |10.000 |100 |10.00 1728 |25 |100 |10.000 |100 |10.000 |
1729 +-------+--------+------------+--------+----- 1729 +-------+--------+------------+--------+-------+
1730 |26 |104 |9.615 |125 | 8.00 1730 |26 |104 |9.615 |125 | 8.000 |
1731 +-------+--------+------------+--------+----- 1731 +-------+--------+------------+--------+-------+
1732 |27 |108 |9.259 |125 | 8.00 1732 |27 |108 |9.259 |125 | 8.000 |
1733 +-------+--------+------------+--------+----- 1733 +-------+--------+------------+--------+-------+
1734 |28 |112 |8.928 |125 | 8.00 1734 |28 |112 |8.928 |125 | 8.000 |
1735 +-------+--------+------------+--------+----- 1735 +-------+--------+------------+--------+-------+
1736 |29 |116 |8.620 |125 | 8.00 1736 |29 |116 |8.620 |125 | 8.000 |
1737 +-------+--------+------------+--------+----- 1737 +-------+--------+------------+--------+-------+
1738 |30 |120 |8.333 |125 | 8.00 1738 |30 |120 |8.333 |125 | 8.000 |
1739 +-------+--------+------------+--------+----- 1739 +-------+--------+------------+--------+-------+
1740 |31 |124 |8.064 |125 | 8.00 1740 |31 |124 |8.064 |125 | 8.000 |
1741 +-------+--------+------------+--------+----- 1741 +-------+--------+------------+--------+-------+
1742 |32 |128 |7.812 |131 | 7.61 1742 |32 |128 |7.812 |131 | 7.619 |
1743 +-------+--------+------------+--------+----- 1743 +-------+--------+------------+--------+-------+
1744 |33 |132 |7.575 |150 | 6.66 1744 |33 |132 |7.575 |150 | 6.666 |
1745 +-------+--------+------------+--------+----- 1745 +-------+--------+------------+--------+-------+
1746 |34 |136 |7.352 |150 | 6.66 1746 |34 |136 |7.352 |150 | 6.666 |
1747 +-------+--------+------------+--------+----- 1747 +-------+--------+------------+--------+-------+
1748 |35 |140 |7.142 |150 | 6.66 1748 |35 |140 |7.142 |150 | 6.666 |
1749 +-------+--------+------------+--------+----- 1749 +-------+--------+------------+--------+-------+
1750 |36 |144 |6.944 |150 | 6.66 1750 |36 |144 |6.944 |150 | 6.666 |
1751 +-------+--------+------------+--------+----- 1751 +-------+--------+------------+--------+-------+
1752 |37 |148 |6.756 |150 | 6.66 1752 |37 |148 |6.756 |150 | 6.666 |
1753 +-------+--------+------------+--------+----- 1753 +-------+--------+------------+--------+-------+
1754 |38 |152 |6.578 |175 | 5.71 1754 |38 |152 |6.578 |175 | 5.714 |
1755 +-------+--------+------------+--------+----- 1755 +-------+--------+------------+--------+-------+
1756 |39 |156 |6.410 |175 | 5.71 1756 |39 |156 |6.410 |175 | 5.714 |
1757 +-------+--------+------------+--------+----- 1757 +-------+--------+------------+--------+-------+
1758 |40 |160 |6.250 |175 | 5.71 1758 |40 |160 |6.250 |175 | 5.714 |
1759 +-------+--------+------------+--------+----- 1759 +-------+--------+------------+--------+-------+
1760 |41 |164 |6.097 |175 | 5.71 1760 |41 |164 |6.097 |175 | 5.714 |
1761 +-------+--------+------------+--------+----- 1761 +-------+--------+------------+--------+-------+
1762 |42 |168 |5.952 |175 | 5.71 1762 |42 |168 |5.952 |175 | 5.714 |
1763 +-------+--------+------------+--------+----- 1763 +-------+--------+------------+--------+-------+
1764 |43 |172 |5.813 |175 | 5.71 1764 |43 |172 |5.813 |175 | 5.714 |
1765 +-------+--------+------------+--------+----- 1765 +-------+--------+------------+--------+-------+
1766 |44 |176 |5.681 |187 | 5.33 1766 |44 |176 |5.681 |187 | 5.333 |
1767 +-------+--------+------------+--------+----- 1767 +-------+--------+------------+--------+-------+
1768 |45 |180 |5.555 |187 | 5.33 1768 |45 |180 |5.555 |187 | 5.333 |
1769 +-------+--------+------------+--------+----- 1769 +-------+--------+------------+--------+-------+
1770 |46 |184 |5.434 |187 | 5.33 1770 |46 |184 |5.434 |187 | 5.333 |
1771 +-------+--------+------------+--------+----- 1771 +-------+--------+------------+--------+-------+
1772 |47 |188 |5.319 |200 | 5.00 1772 |47 |188 |5.319 |200 | 5.000 |
1773 +-------+--------+------------+--------+----- 1773 +-------+--------+------------+--------+-------+
1774 |48 |192 |5.208 |200 | 5.00 1774 |48 |192 |5.208 |200 | 5.000 |
1775 +-------+--------+------------+--------+----- 1775 +-------+--------+------------+--------+-------+
1776 |49 |196 |5.102 |200 | 5.00 1776 |49 |196 |5.102 |200 | 5.000 |
1777 +-------+--------+------------+--------+----- 1777 +-------+--------+------------+--------+-------+
1778 1778
1779 1779
1780 17. Serial NVRAM 1780 17. Serial NVRAM
1781 ================ 1781 ================
1782 1782
1783 (added by Richard Waltham: dormouse@farsrobt. 1783 (added by Richard Waltham: dormouse@farsrobt.demon.co.uk)
1784 1784
1785 17.1 Features 1785 17.1 Features
1786 ------------- 1786 -------------
1787 1787
1788 Enabling serial NVRAM support enables detecti 1788 Enabling serial NVRAM support enables detection of the serial NVRAM included
1789 on Symbios and some Symbios compatible host a 1789 on Symbios and some Symbios compatible host adaptors, and Tekram boards. The
1790 serial NVRAM is used by Symbios and Tekram to 1790 serial NVRAM is used by Symbios and Tekram to hold set up parameters for the
1791 host adaptor and its attached drives. 1791 host adaptor and its attached drives.
1792 1792
1793 The Symbios NVRAM also holds data on the boot 1793 The Symbios NVRAM also holds data on the boot order of host adaptors in a
1794 system with more than one host adaptor. This 1794 system with more than one host adaptor. This enables the order of scanning
1795 the cards for drives to be changed from the d 1795 the cards for drives to be changed from the default used during host adaptor
1796 detection. 1796 detection.
1797 1797
1798 This can be done to a limited extent at the m 1798 This can be done to a limited extent at the moment using "reverse probe" but
1799 this only changes the order of detection of d 1799 this only changes the order of detection of different types of cards. The
1800 NVRAM boot order settings can do this as well 1800 NVRAM boot order settings can do this as well as change the order the same
1801 types of cards are scanned in, something "rev 1801 types of cards are scanned in, something "reverse probe" cannot do.
1802 1802
1803 Tekram boards using Symbios chips, DC390W/F/U 1803 Tekram boards using Symbios chips, DC390W/F/U, which have NVRAM are detected
1804 and this is used to distinguish between Symbi 1804 and this is used to distinguish between Symbios compatible and Tekram host
1805 adaptors. This is used to disable the Symbios 1805 adaptors. This is used to disable the Symbios compatible "diff" setting
1806 incorrectly set on Tekram boards if the CONFI 1806 incorrectly set on Tekram boards if the CONFIG_SCSI_53C8XX_SYMBIOS_COMPAT
1807 configuration parameter is set enabling both 1807 configuration parameter is set enabling both Symbios and Tekram boards to be
1808 used together with the Symbios cards using al 1808 used together with the Symbios cards using all their features, including
1809 "diff" support. ("led pin" support for Symbio 1809 "diff" support. ("led pin" support for Symbios compatible cards can remain
1810 enabled when using Tekram cards. It does noth 1810 enabled when using Tekram cards. It does nothing useful for Tekram host
1811 adaptors but does not cause problems either.) 1811 adaptors but does not cause problems either.)
1812 1812
1813 1813
1814 17.2 Symbios NVRAM layout 1814 17.2 Symbios NVRAM layout
1815 ------------------------- 1815 -------------------------
1816 1816
1817 typical data at NVRAM address 0x100 (53c810a 1817 typical data at NVRAM address 0x100 (53c810a NVRAM)::
1818 1818
1819 00 00 1819 00 00
1820 64 01 1820 64 01
1821 8e 0b 1821 8e 0b
1822 1822
1823 00 30 00 00 00 00 07 00 00 00 00 00 00 00 1823 00 30 00 00 00 00 07 00 00 00 00 00 00 00 07 04 10 04 00 00
1824 1824
1825 04 00 0f 00 00 10 00 50 00 00 01 00 00 62 1825 04 00 0f 00 00 10 00 50 00 00 01 00 00 62
1826 04 00 03 00 00 10 00 58 00 00 01 00 00 63 1826 04 00 03 00 00 10 00 58 00 00 01 00 00 63
1827 04 00 01 00 00 10 00 48 00 00 01 00 00 61 1827 04 00 01 00 00 10 00 48 00 00 01 00 00 61
1828 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1828 00 00 00 00 00 00 00 00 00 00 00 00 00 00
1829 1829
1830 0f 00 08 08 64 00 0a 00 1830 0f 00 08 08 64 00 0a 00
1831 0f 00 08 08 64 00 0a 00 1831 0f 00 08 08 64 00 0a 00
1832 0f 00 08 08 64 00 0a 00 1832 0f 00 08 08 64 00 0a 00
1833 0f 00 08 08 64 00 0a 00 1833 0f 00 08 08 64 00 0a 00
1834 0f 00 08 08 64 00 0a 00 1834 0f 00 08 08 64 00 0a 00
1835 0f 00 08 08 64 00 0a 00 1835 0f 00 08 08 64 00 0a 00
1836 0f 00 08 08 64 00 0a 00 1836 0f 00 08 08 64 00 0a 00
1837 0f 00 08 08 64 00 0a 00 1837 0f 00 08 08 64 00 0a 00
1838 1838
1839 0f 00 08 08 64 00 0a 00 1839 0f 00 08 08 64 00 0a 00
1840 0f 00 08 08 64 00 0a 00 1840 0f 00 08 08 64 00 0a 00
1841 0f 00 08 08 64 00 0a 00 1841 0f 00 08 08 64 00 0a 00
1842 0f 00 08 08 64 00 0a 00 1842 0f 00 08 08 64 00 0a 00
1843 0f 00 08 08 64 00 0a 00 1843 0f 00 08 08 64 00 0a 00
1844 0f 00 08 08 64 00 0a 00 1844 0f 00 08 08 64 00 0a 00
1845 0f 00 08 08 64 00 0a 00 1845 0f 00 08 08 64 00 0a 00
1846 0f 00 08 08 64 00 0a 00 1846 0f 00 08 08 64 00 0a 00
1847 1847
1848 00 00 00 00 00 00 00 00 1848 00 00 00 00 00 00 00 00
1849 00 00 00 00 00 00 00 00 1849 00 00 00 00 00 00 00 00
1850 00 00 00 00 00 00 00 00 1850 00 00 00 00 00 00 00 00
1851 00 00 00 00 00 00 00 00 1851 00 00 00 00 00 00 00 00
1852 00 00 00 00 00 00 00 00 1852 00 00 00 00 00 00 00 00
1853 00 00 00 00 00 00 00 00 1853 00 00 00 00 00 00 00 00
1854 00 00 00 00 00 00 00 00 1854 00 00 00 00 00 00 00 00
1855 00 00 00 00 00 00 00 00 1855 00 00 00 00 00 00 00 00
1856 1856
1857 00 00 00 00 00 00 00 00 1857 00 00 00 00 00 00 00 00
1858 00 00 00 00 00 00 00 00 1858 00 00 00 00 00 00 00 00
1859 00 00 00 00 00 00 00 00 1859 00 00 00 00 00 00 00 00
1860 00 00 00 00 00 00 00 00 1860 00 00 00 00 00 00 00 00
1861 00 00 00 00 00 00 00 00 1861 00 00 00 00 00 00 00 00
1862 00 00 00 00 00 00 00 00 1862 00 00 00 00 00 00 00 00
1863 00 00 00 00 00 00 00 00 1863 00 00 00 00 00 00 00 00
1864 00 00 00 00 00 00 00 00 1864 00 00 00 00 00 00 00 00
1865 1865
1866 00 00 00 00 00 00 00 00 1866 00 00 00 00 00 00 00 00
1867 00 00 00 00 00 00 00 00 1867 00 00 00 00 00 00 00 00
1868 00 00 00 00 00 00 00 00 1868 00 00 00 00 00 00 00 00
1869 1869
1870 fe fe 1870 fe fe
1871 00 00 1871 00 00
1872 00 00 1872 00 00
1873 1873
1874 NVRAM layout details 1874 NVRAM layout details
1875 1875
1876 ============= ================ 1876 ============= ================
1877 NVRAM Address 1877 NVRAM Address
1878 ============= ================ 1878 ============= ================
1879 0x000-0x0ff not used 1879 0x000-0x0ff not used
1880 0x100-0x26f initialised data 1880 0x100-0x26f initialised data
1881 0x270-0x7ff not used 1881 0x270-0x7ff not used
1882 ============= ================ 1882 ============= ================
1883 1883
1884 general layout:: 1884 general layout::
1885 1885
1886 header - 6 bytes, 1886 header - 6 bytes,
1887 data - 356 bytes (checksum is byte 1887 data - 356 bytes (checksum is byte sum of this data)
1888 trailer - 6 bytes 1888 trailer - 6 bytes
1889 --- 1889 ---
1890 total 368 bytes 1890 total 368 bytes
1891 1891
1892 data area layout:: 1892 data area layout::
1893 1893
1894 controller set up - 20 bytes 1894 controller set up - 20 bytes
1895 boot configuration - 56 bytes (4x14 1895 boot configuration - 56 bytes (4x14 bytes)
1896 device set up - 128 bytes (16x8 1896 device set up - 128 bytes (16x8 bytes)
1897 unused (spare?) - 152 bytes (19x8 1897 unused (spare?) - 152 bytes (19x8 bytes)
1898 --- 1898 ---
1899 total 356 bytes 1899 total 356 bytes
1900 1900
1901 header:: 1901 header::
1902 1902
1903 00 00 - ?? start marker 1903 00 00 - ?? start marker
1904 64 01 - byte count (lsb/msb excludes he 1904 64 01 - byte count (lsb/msb excludes header/trailer)
1905 8e 0b - checksum (lsb/msb excludes head 1905 8e 0b - checksum (lsb/msb excludes header/trailer)
1906 1906
1907 controller set up:: 1907 controller set up::
1908 1908
1909 00 30 00 00 00 00 07 00 00 00 00 00 00 00 1909 00 30 00 00 00 00 07 00 00 00 00 00 00 00 07 04 10 04 00 00
1910 | | | | 1910 | | | |
1911 | | | 1911 | | | -- host ID
1912 | | | 1912 | | |
1913 | | --Remo 1913 | | --Removable Media Support
1914 | | 0x0 1914 | | 0x00 = none
1915 | | 0x0 1915 | | 0x01 = Bootable Device
1916 | | 0x0 1916 | | 0x02 = All with Media
1917 | | 1917 | |
1918 | --flag bits 2 1918 | --flag bits 2
1919 | 0x00000001= scan 1919 | 0x00000001= scan order hi->low
1920 | (default 0x0 1920 | (default 0x00 - scan low->hi)
1921 --flag bits 1 1921 --flag bits 1
1922 0x00000001 scam enabl 1922 0x00000001 scam enable
1923 0x00000010 parity ena 1923 0x00000010 parity enable
1924 0x00000100 verbose bo 1924 0x00000100 verbose boot msgs
1925 1925
1926 remaining bytes unknown - they do not appear 1926 remaining bytes unknown - they do not appear to change in my
1927 current set up for any of the controllers. 1927 current set up for any of the controllers.
1928 1928
1929 default set up is identical for 53c810a and 5 1929 default set up is identical for 53c810a and 53c875 NVRAM
1930 (Removable Media added Symbios BIOS version 4 1930 (Removable Media added Symbios BIOS version 4.09)
1931 1931
1932 boot configuration 1932 boot configuration
1933 1933
1934 boot order set by order of the devices in thi 1934 boot order set by order of the devices in this table::
1935 1935
1936 04 00 0f 00 00 10 00 50 00 00 01 00 00 62 1936 04 00 0f 00 00 10 00 50 00 00 01 00 00 62 -- 1st controller
1937 04 00 03 00 00 10 00 58 00 00 01 00 00 63 1937 04 00 03 00 00 10 00 58 00 00 01 00 00 63 2nd controller
1938 04 00 01 00 00 10 00 48 00 00 01 00 00 61 1938 04 00 01 00 00 10 00 48 00 00 01 00 00 61 3rd controller
1939 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1939 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4th controller
1940 | | | | | | | | 1940 | | | | | | | |
1941 | | | | | | ---- P 1941 | | | | | | ---- PCI io port adr
1942 | | | | | --0x01 init/ 1942 | | | | | --0x01 init/scan at boot time
1943 | | | | --PCI device/function 1943 | | | | --PCI device/function number (0xdddddfff)
1944 | | ----- ?? PCI vendor ID (lsb/ms 1944 | | ----- ?? PCI vendor ID (lsb/msb)
1945 ----PCI device ID (lsb/msb) 1945 ----PCI device ID (lsb/msb)
1946 1946
1947 ?? use of this data is a guess but seems 1947 ?? use of this data is a guess but seems reasonable
1948 1948
1949 remaining bytes unknown - they do not appear 1949 remaining bytes unknown - they do not appear to change in my
1950 current set up 1950 current set up
1951 1951
1952 default set up is identical for 53c810a and 5 1952 default set up is identical for 53c810a and 53c875 NVRAM
1953 --------------------------------------------- 1953 --------------------------------------------------------
1954 1954
1955 device set up (up to 16 devices - includes co 1955 device set up (up to 16 devices - includes controller)::
1956 1956
1957 0f 00 08 08 64 00 0a 00 - id 0 1957 0f 00 08 08 64 00 0a 00 - id 0
1958 0f 00 08 08 64 00 0a 00 1958 0f 00 08 08 64 00 0a 00
1959 0f 00 08 08 64 00 0a 00 1959 0f 00 08 08 64 00 0a 00
1960 0f 00 08 08 64 00 0a 00 1960 0f 00 08 08 64 00 0a 00
1961 0f 00 08 08 64 00 0a 00 1961 0f 00 08 08 64 00 0a 00
1962 0f 00 08 08 64 00 0a 00 1962 0f 00 08 08 64 00 0a 00
1963 0f 00 08 08 64 00 0a 00 1963 0f 00 08 08 64 00 0a 00
1964 0f 00 08 08 64 00 0a 00 1964 0f 00 08 08 64 00 0a 00
1965 1965
1966 0f 00 08 08 64 00 0a 00 1966 0f 00 08 08 64 00 0a 00
1967 0f 00 08 08 64 00 0a 00 1967 0f 00 08 08 64 00 0a 00
1968 0f 00 08 08 64 00 0a 00 1968 0f 00 08 08 64 00 0a 00
1969 0f 00 08 08 64 00 0a 00 1969 0f 00 08 08 64 00 0a 00
1970 0f 00 08 08 64 00 0a 00 1970 0f 00 08 08 64 00 0a 00
1971 0f 00 08 08 64 00 0a 00 1971 0f 00 08 08 64 00 0a 00
1972 0f 00 08 08 64 00 0a 00 1972 0f 00 08 08 64 00 0a 00
1973 0f 00 08 08 64 00 0a 00 - id 15 1973 0f 00 08 08 64 00 0a 00 - id 15
1974 | | | | | | 1974 | | | | | |
1975 | | | | ----timeout (lsb/msb) 1975 | | | | ----timeout (lsb/msb)
1976 | | | --synch period (0x?? 40 Mtra 1976 | | | --synch period (0x?? 40 Mtrans/sec- fast 40) (probably 0x28)
1977 | | | (0x30 20 Mtra 1977 | | | (0x30 20 Mtrans/sec- fast 20)
1978 | | | (0x64 10 Mtra 1978 | | | (0x64 10 Mtrans/sec- fast )
1979 | | | (0xc8 5 Mtra 1979 | | | (0xc8 5 Mtrans/sec)
1980 | | | (0x00 asynch 1980 | | | (0x00 asynchronous)
1981 | | -- ?? max sync offset (0x08 in 1981 | | -- ?? max sync offset (0x08 in NVRAM on 53c810a)
1982 | | (0x10 in 1982 | | (0x10 in NVRAM on 53c875)
1983 | --device bus width (0x08 narrow) 1983 | --device bus width (0x08 narrow)
1984 | (0x10 16 bit wi 1984 | (0x10 16 bit wide)
1985 --flag bits 1985 --flag bits
1986 0x00000001 - disconnect enabled 1986 0x00000001 - disconnect enabled
1987 0x00000010 - scan at boot time 1987 0x00000010 - scan at boot time
1988 0x00000100 - scan luns 1988 0x00000100 - scan luns
1989 0x00001000 - queue tags enabled 1989 0x00001000 - queue tags enabled
1990 1990
1991 remaining bytes unknown - they do not appear 1991 remaining bytes unknown - they do not appear to change in my
1992 current set up 1992 current set up
1993 1993
1994 ?? use of this data is a guess but seems reas 1994 ?? use of this data is a guess but seems reasonable
1995 (but it could be max bus width) 1995 (but it could be max bus width)
1996 1996
1997 default set up for 53c810a NVRAM 1997 default set up for 53c810a NVRAM
1998 default set up for 53c875 NVRAM 1998 default set up for 53c875 NVRAM
1999 1999
2000 - bus width 2000 - bus width - 0x10
2001 - sync offset 2001 - sync offset ? - 0x10
2002 - sync period 2002 - sync period - 0x30
2003 2003
2004 ?? spare device space (32 bit bus ??) 2004 ?? spare device space (32 bit bus ??)
2005 2005
2006 :: 2006 ::
2007 2007
2008 00 00 00 00 00 00 00 00 (19x8bytes) 2008 00 00 00 00 00 00 00 00 (19x8bytes)
2009 . 2009 .
2010 . 2010 .
2011 00 00 00 00 00 00 00 00 2011 00 00 00 00 00 00 00 00
2012 2012
2013 default set up is identical for 53c810a and 5 2013 default set up is identical for 53c810a and 53c875 NVRAM
2014 --------------------------------------------- 2014 --------------------------------------------------------
2015 2015
2016 trailer:: 2016 trailer::
2017 2017
2018 fe fe - ? end marker ? 2018 fe fe - ? end marker ?
2019 00 00 2019 00 00
2020 00 00 2020 00 00
2021 2021
2022 default set up is identical for 53c810a and 5 2022 default set up is identical for 53c810a and 53c875 NVRAM
2023 --------------------------------------------- 2023 -----------------------------------------------------------
2024 2024
2025 2025
2026 2026
2027 17.3 Tekram NVRAM layout 2027 17.3 Tekram NVRAM layout
2028 ------------------------ 2028 ------------------------
2029 2029
2030 nvram 64x16 (1024 bit) 2030 nvram 64x16 (1024 bit)
2031 2031
2032 Drive settings:: 2032 Drive settings::
2033 2033
2034 Drive ID 0-15 (addr 0x0yyyy0 = device set 2034 Drive ID 0-15 (addr 0x0yyyy0 = device setup, yyyy = ID)
2035 (addr 0x0yyyy1 = 0x0000) 2035 (addr 0x0yyyy1 = 0x0000)
2036 2036
2037 x x x x x x x x x x x x x x x x 2037 x x x x x x x x x x x x x x x x
2038 | | | | | | | | | 2038 | | | | | | | | |
2039 | | | | | | | | ----- 2039 | | | | | | | | ----- parity check 0 - off
2040 | | | | | | | | 2040 | | | | | | | | 1 - on
2041 | | | | | | | | 2041 | | | | | | | |
2042 | | | | | | | ------- 2042 | | | | | | | ------- sync neg 0 - off
2043 | | | | | | | 2043 | | | | | | | 1 - on
2044 | | | | | | | 2044 | | | | | | |
2045 | | | | | | --------- 2045 | | | | | | --------- disconnect 0 - off
2046 | | | | | | 2046 | | | | | | 1 - on
2047 | | | | | | 2047 | | | | | |
2048 | | | | | ----------- 2048 | | | | | ----------- start cmd 0 - off
2049 | | | | | 2049 | | | | | 1 - on
2050 | | | | | 2050 | | | | |
2051 | | | | -------------- 2051 | | | | -------------- tagged cmds 0 - off
2052 | | | | 2052 | | | | 1 - on
2053 | | | | 2053 | | | |
2054 | | | ---------------- 2054 | | | ---------------- wide neg 0 - off
2055 | | | 2055 | | | 1 - on
2056 | | | 2056 | | |
2057 ------------------------- 2057 --------------------------- sync rate 0 - 10.0 Mtrans/sec
2058 2058 1 - 8.0
2059 2059 2 - 6.6
2060 2060 3 - 5.7
2061 2061 4 - 5.0
2062 2062 5 - 4.0
2063 2063 6 - 3.0
2064 2064 7 - 2.0
2065 2065 7 - 2.0
2066 2066 8 - 20.0
2067 2067 9 - 16.7
2068 2068 a - 13.9
2069 2069 b - 11.9
2070 2070
2071 Global settings 2071 Global settings
2072 2072
2073 Host flags 0 (addr 0x100000, 32):: 2073 Host flags 0 (addr 0x100000, 32)::
2074 2074
2075 x x x x x x x x x x x x x x x x 2075 x x x x x x x x x x x x x x x x
2076 | | | | | | | | | | | | 2076 | | | | | | | | | | | |
2077 | | | | | | | | ----------- h 2077 | | | | | | | | ----------- host ID 0x00 - 0x0f
2078 | | | | | | | | 2078 | | | | | | | |
2079 | | | | | | | ----------------------- s 2079 | | | | | | | ----------------------- support for 0 - off
2080 | | | | | | | > 2080 | | | | | | | > 2 drives 1 - on
2081 | | | | | | | 2081 | | | | | | |
2082 | | | | | | ------------------------- s 2082 | | | | | | ------------------------- support drives 0 - off
2083 | | | | | | > 2083 | | | | | | > 1Gbytes 1 - on
2084 | | | | | | 2084 | | | | | |
2085 | | | | | --------------------------- b 2085 | | | | | --------------------------- bus reset on 0 - off
2086 | | | | | 2086 | | | | | power on 1 - on
2087 | | | | | 2087 | | | | |
2088 | | | | ----------------------------- a 2088 | | | | ----------------------------- active neg 0 - off
2089 | | | | 2089 | | | | 1 - on
2090 | | | | 2090 | | | |
2091 | | | -------------------------------- i 2091 | | | -------------------------------- imm seek 0 - off
2092 | | | 2092 | | | 1 - on
2093 | | | 2093 | | |
2094 | | ---------------------------------- s 2094 | | ---------------------------------- scan luns 0 - off
2095 | | 2095 | | 1 - on
2096 | | 2096 | |
2097 -------------------------------------- r 2097 -------------------------------------- removable 0 - disable
2098 a 2098 as BIOS dev 1 - boot device
2099 2099 2 - all
2100 2100
2101 Host flags 1 (addr 0x100001, 33):: 2101 Host flags 1 (addr 0x100001, 33)::
2102 2102
2103 x x x x x x x x x x x x x x x x 2103 x x x x x x x x x x x x x x x x
2104 | | | | | | 2104 | | | | | |
2105 | | | --------- b 2105 | | | --------- boot delay 0 - 3 sec
2106 | | | 2106 | | | 1 - 5
2107 | | | 2107 | | | 2 - 10
2108 | | | 2108 | | | 3 - 20
2109 | | | 2109 | | | 4 - 30
2110 | | | 2110 | | | 5 - 60
2111 | | | 2111 | | | 6 - 120
2112 | | | 2112 | | |
2113 --------------------------- m 2113 --------------------------- max tag cmds 0 - 2
2114 2114 1 - 4
2115 2115 2 - 8
2116 2116 3 - 16
2117 2117 4 - 32
2118 2118
2119 Host flags 2 (addr 0x100010, 34):: 2119 Host flags 2 (addr 0x100010, 34)::
2120 2120
2121 x x x x x x x x x x x x x x x x 2121 x x x x x x x x x x x x x x x x
2122 | 2122 |
2123 ----- F 2123 ----- F2/F6 enable 0 - off ???
2124 2124 1 - on ???
2125 2125
2126 checksum (addr 0x111111) 2126 checksum (addr 0x111111)
2127 2127
2128 checksum = 0x1234 - (sum addr 0-63) 2128 checksum = 0x1234 - (sum addr 0-63)
2129 2129
2130 --------------------------------------------- 2130 ----------------------------------------------------------------------------
2131 2131
2132 default nvram data:: 2132 default nvram data::
2133 2133
2134 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 2134 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
2135 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 2135 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
2136 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 2136 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
2137 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 2137 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
2138 2138
2139 0x0f07 0x0400 0x0001 0x0000 0x0000 0x0000 2139 0x0f07 0x0400 0x0001 0x0000 0x0000 0x0000 0x0000 0x0000
2140 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 2140 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
2141 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 2141 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
2142 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 2142 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0xfbbc
2143 2143
2144 2144
2145 18. Support for Big Endian 2145 18. Support for Big Endian
2146 ========================== 2146 ==========================
2147 2147
2148 The PCI local bus has been primarily designed 2148 The PCI local bus has been primarily designed for x86 architecture.
2149 As a consequence, PCI devices generally expec 2149 As a consequence, PCI devices generally expect DWORDS using little endian
2150 byte ordering. 2150 byte ordering.
2151 2151
2152 18.1 Big Endian CPU 2152 18.1 Big Endian CPU
2153 ------------------- 2153 -------------------
2154 2154
2155 In order to support NCR chips on a Big Endian 2155 In order to support NCR chips on a Big Endian architecture the driver has to
2156 perform byte reordering each time it is neede 2156 perform byte reordering each time it is needed. This feature has been
2157 added to the driver by Cort <cort@cs.nmt.edu> 2157 added to the driver by Cort <cort@cs.nmt.edu> and is available in driver
2158 version 2.5 and later ones. For the moment Bi 2158 version 2.5 and later ones. For the moment Big Endian support has only
2159 been tested on Linux/PPC (PowerPC). 2159 been tested on Linux/PPC (PowerPC).
2160 2160
2161 18.2 NCR chip in Big Endian mode of operation 2161 18.2 NCR chip in Big Endian mode of operations
2162 --------------------------------------------- 2162 ----------------------------------------------
2163 2163
2164 It can be read in SYMBIOS documentation that 2164 It can be read in SYMBIOS documentation that some chips support a special
2165 Big Endian mode, on paper: 53C815, 53C825A, 5 2165 Big Endian mode, on paper: 53C815, 53C825A, 53C875, 53C875N, 53C895.
2166 This mode of operations is not software-selec 2166 This mode of operations is not software-selectable, but needs pin named
2167 BigLit to be pulled-up. Using this mode, most 2167 BigLit to be pulled-up. Using this mode, most of byte reorderings should
2168 be avoided when the driver is running on a Bi 2168 be avoided when the driver is running on a Big Endian CPU.
2169 Driver version 2.5 is also, in theory, ready 2169 Driver version 2.5 is also, in theory, ready for this feature.
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.