1 .. SPDX-License-Identifier: GPL-2.0 1 .. SPDX-License-Identifier: GPL-2.0
2 2
3 ============ 3 ============
4 SYM-2 driver 4 SYM-2 driver
5 ============ 5 ============
6 6
7 Written by Gerard Roudier <groudier@free.fr> 7 Written by Gerard Roudier <groudier@free.fr>
8 8
9 21 Rue Carnot 9 21 Rue Carnot
10 10
11 95170 DEUIL LA BARRE - FRANCE 11 95170 DEUIL LA BARRE - FRANCE
12 12
13 Updated by Matthew Wilcox <matthew@wil.cx> 13 Updated by Matthew Wilcox <matthew@wil.cx>
14 14
15 2004-10-09 15 2004-10-09
16 16
17 .. Contents 17 .. Contents
18 18
19 1. Introduction 19 1. Introduction
20 2. Supported chips and SCSI features 20 2. Supported chips and SCSI features
21 3. Advantages of this driver for newer chi 21 3. Advantages of this driver for newer chips.
22 3.1 Optimized SCSI SCRIPTS 22 3.1 Optimized SCSI SCRIPTS
23 3.2 New features appeared with the SY 23 3.2 New features appeared with the SYM53C896
24 4. Memory mapped I/O versus normal I/O 24 4. Memory mapped I/O versus normal I/O
25 5. Tagged command queueing 25 5. Tagged command queueing
26 6. Parity checking 26 6. Parity checking
27 7. Profiling information 27 7. Profiling information
28 8. Control commands 28 8. Control commands
29 8.1 Set minimum synchronous period 29 8.1 Set minimum synchronous period
30 8.2 Set wide size 30 8.2 Set wide size
31 8.3 Set maximum number of concurrent 31 8.3 Set maximum number of concurrent tagged commands
32 8.4 Set debug mode 32 8.4 Set debug mode
33 8.5 Set flag (no_disc) 33 8.5 Set flag (no_disc)
34 8.6 Set verbose level 34 8.6 Set verbose level
35 8.7 Reset all logical units of a tar 35 8.7 Reset all logical units of a target
36 8.8 Abort all tasks of all logical u 36 8.8 Abort all tasks of all logical units of a target
37 9. Configuration parameters 37 9. Configuration parameters
38 10. Boot setup commands 38 10. Boot setup commands
39 10.1 Syntax 39 10.1 Syntax
40 10.2 Available arguments 40 10.2 Available arguments
41 10.2.1 Default number of tagg 41 10.2.1 Default number of tagged commands
42 10.2.2 Burst max 42 10.2.2 Burst max
43 10.2.3 LED support 43 10.2.3 LED support
44 10.2.4 Differential mode 44 10.2.4 Differential mode
45 10.2.5 IRQ mode 45 10.2.5 IRQ mode
46 10.2.6 Check SCSI BUS 46 10.2.6 Check SCSI BUS
47 10.2.7 Suggest a default SCSI 47 10.2.7 Suggest a default SCSI id for hosts
48 10.2.8 Verbosity level 48 10.2.8 Verbosity level
49 10.2.9 Debug mode 49 10.2.9 Debug mode
50 10.2.10 Settle delay 50 10.2.10 Settle delay
51 10.2.11 Serial NVRAM 51 10.2.11 Serial NVRAM
52 10.2.12 Exclude a host from be 52 10.2.12 Exclude a host from being attached
53 10.3 Converting from old options 53 10.3 Converting from old options
54 10.4 SCSI BUS checking boot option 54 10.4 SCSI BUS checking boot option
55 11. SCSI problem troubleshooting 55 11. SCSI problem troubleshooting
56 15.1 Problem tracking 56 15.1 Problem tracking
57 15.2 Understanding hardware error rep 57 15.2 Understanding hardware error reports
58 12. Serial NVRAM support (by Richard Waltha 58 12. Serial NVRAM support (by Richard Waltham)
59 17.1 Features 59 17.1 Features
60 17.2 Symbios NVRAM layout 60 17.2 Symbios NVRAM layout
61 17.3 Tekram NVRAM layout 61 17.3 Tekram NVRAM layout
62 62
63 63
64 1. Introduction 64 1. Introduction
65 =============== 65 ===============
66 66
67 This driver supports the whole SYM53C8XX famil 67 This driver supports the whole SYM53C8XX family of PCI-SCSI controllers.
68 It also support the subset of LSI53C10XX PCI-S 68 It also support the subset of LSI53C10XX PCI-SCSI controllers that are based
69 on the SYM53C8XX SCRIPTS language. 69 on the SYM53C8XX SCRIPTS language.
70 70
71 It replaces the sym53c8xx+ncr53c8xx driver bun 71 It replaces the sym53c8xx+ncr53c8xx driver bundle and shares its core code
72 with the FreeBSD SYM-2 driver. The 'glue' that 72 with the FreeBSD SYM-2 driver. The 'glue' that allows this driver to work
73 under Linux is contained in 2 files named sym_ 73 under Linux is contained in 2 files named sym_glue.h and sym_glue.c.
74 Other drivers files are intended not to depend 74 Other drivers files are intended not to depend on the Operating System
75 on which the driver is used. 75 on which the driver is used.
76 76
77 The history of this driver can be summarized a 77 The history of this driver can be summarized as follows:
78 78
79 1993: ncr driver written for 386bsd and FreeBS 79 1993: ncr driver written for 386bsd and FreeBSD by:
80 80
81 - Wolfgang Stanglmeier <wolf@c 81 - Wolfgang Stanglmeier <wolf@cologne.de>
82 - Stefan Esser <se@mi. 82 - Stefan Esser <se@mi.Uni-Koeln.de>
83 83
84 1996: port of the ncr driver to Linux-1.2.13 a 84 1996: port of the ncr driver to Linux-1.2.13 and rename it ncr53c8xx.
85 85
86 - Gerard Roudier 86 - Gerard Roudier
87 87
88 1998: new sym53c8xx driver for Linux based on 88 1998: new sym53c8xx driver for Linux based on LOAD/STORE instruction and that
89 adds full support for the 896 but drops 89 adds full support for the 896 but drops support for early NCR devices.
90 90
91 - Gerard Roudier 91 - Gerard Roudier
92 92
93 1999: port of the sym53c8xx driver to FreeBSD 93 1999: port of the sym53c8xx driver to FreeBSD and support for the LSI53C1010
94 33 MHz and 66MHz Ultra-3 controllers. Th 94 33 MHz and 66MHz Ultra-3 controllers. The new driver is named 'sym'.
95 95
96 - Gerard Roudier 96 - Gerard Roudier
97 97
98 2000: Add support for early NCR devices to Fre 98 2000: Add support for early NCR devices to FreeBSD 'sym' driver.
99 Break the driver into several sources an 99 Break the driver into several sources and separate the OS glue
100 code from the core code that can be shar 100 code from the core code that can be shared among different O/Ses.
101 Write a glue code for Linux. 101 Write a glue code for Linux.
102 102
103 - Gerard Roudier 103 - Gerard Roudier
104 104
105 2004: Remove FreeBSD compatibility code. Remo 105 2004: Remove FreeBSD compatibility code. Remove support for versions of
106 Linux before 2.6. Start using Linux fac 106 Linux before 2.6. Start using Linux facilities.
107 107
108 This README file addresses the Linux version o 108 This README file addresses the Linux version of the driver. Under FreeBSD,
109 the driver documentation is the sym.8 man page 109 the driver documentation is the sym.8 man page.
110 110
111 Information about new chips is available at LS 111 Information about new chips is available at LSILOGIC web server:
112 112
113 http://www.lsilogic.com/ 113 http://www.lsilogic.com/
114 114
115 SCSI standard documentations are available at 115 SCSI standard documentations are available at T10 site:
116 116
117 http://www.t10.org/ 117 http://www.t10.org/
118 118
119 Useful SCSI tools written by Eric Youngdale ar 119 Useful SCSI tools written by Eric Youngdale are part of most Linux
120 distributions: 120 distributions:
121 121
122 ============ ========================== 122 ============ ==========================
123 scsiinfo command line tool 123 scsiinfo command line tool
124 scsi-config TCL/Tk tool using scsiinfo 124 scsi-config TCL/Tk tool using scsiinfo
125 ============ ========================== 125 ============ ==========================
126 126
127 2. Supported chips and SCSI features 127 2. Supported chips and SCSI features
128 ==================================== 128 ====================================
129 129
130 The following features are supported for all c 130 The following features are supported for all chips:
131 131
132 - Synchronous negotiation 132 - Synchronous negotiation
133 - Disconnection 133 - Disconnection
134 - Tagged command queuing 134 - Tagged command queuing
135 - SCSI parity checking 135 - SCSI parity checking
136 - PCI Master parity checking 136 - PCI Master parity checking
137 137
138 Other features depends on chip capabilities. 138 Other features depends on chip capabilities.
139 139
140 The driver notably uses optimized SCRIPTS for 140 The driver notably uses optimized SCRIPTS for devices that support
141 LOAD/STORE and handles PHASE MISMATCH from SCR 141 LOAD/STORE and handles PHASE MISMATCH from SCRIPTS for devices that
142 support the corresponding feature. 142 support the corresponding feature.
143 143
144 The following table shows some characteristics 144 The following table shows some characteristics of the chip family.
145 145
146 +--------+-----------+-----+-----------+------ 146 +--------+-----------+-----+-----------+------------+------------+---------+
147 | | | | | 147 | | | | | |Load/store |Hardware |
148 | |On board | | | 148 | |On board | | | |scripts |phase |
149 |Chip |SDMS BIOS |Wide |SCSI std. | Max. 149 |Chip |SDMS BIOS |Wide |SCSI std. | Max. sync | |mismatch |
150 +--------+-----------+-----+-----------+------ 150 +--------+-----------+-----+-----------+------------+------------+---------+
151 |810 | N | N | FAST10 | 10 MB 151 |810 | N | N | FAST10 | 10 MB/s | N | N |
152 +--------+-----------+-----+-----------+------ 152 +--------+-----------+-----+-----------+------------+------------+---------+
153 |810A | N | N | FAST10 | 10 MB 153 |810A | N | N | FAST10 | 10 MB/s | Y | N |
154 +--------+-----------+-----+-----------+------ 154 +--------+-----------+-----+-----------+------------+------------+---------+
155 |815 | Y | N | FAST10 | 10 MB 155 |815 | Y | N | FAST10 | 10 MB/s | N | N |
156 +--------+-----------+-----+-----------+------ 156 +--------+-----------+-----+-----------+------------+------------+---------+
157 |825 | Y | Y | FAST10 | 20 MB 157 |825 | Y | Y | FAST10 | 20 MB/s | N | N |
158 +--------+-----------+-----+-----------+------ 158 +--------+-----------+-----+-----------+------------+------------+---------+
159 |825A | Y | Y | FAST10 | 20 MB 159 |825A | Y | Y | FAST10 | 20 MB/s | Y | N |
160 +--------+-----------+-----+-----------+------ 160 +--------+-----------+-----+-----------+------------+------------+---------+
161 |860 | N | N | FAST20 | 20 MB 161 |860 | N | N | FAST20 | 20 MB/s | Y | N |
162 +--------+-----------+-----+-----------+------ 162 +--------+-----------+-----+-----------+------------+------------+---------+
163 |875 | Y | Y | FAST20 | 40 MB 163 |875 | Y | Y | FAST20 | 40 MB/s | Y | N |
164 +--------+-----------+-----+-----------+------ 164 +--------+-----------+-----+-----------+------------+------------+---------+
165 |875A | Y | Y | FAST20 | 40 MB 165 |875A | Y | Y | FAST20 | 40 MB/s | Y | Y |
166 +--------+-----------+-----+-----------+------ 166 +--------+-----------+-----+-----------+------------+------------+---------+
167 |876 | Y | Y | FAST20 | 40 MB 167 |876 | Y | Y | FAST20 | 40 MB/s | Y | N |
168 +--------+-----------+-----+-----------+------ 168 +--------+-----------+-----+-----------+------------+------------+---------+
169 |895 | Y | Y | FAST40 | 80 MB 169 |895 | Y | Y | FAST40 | 80 MB/s | Y | N |
170 +--------+-----------+-----+-----------+------ 170 +--------+-----------+-----+-----------+------------+------------+---------+
171 |895A | Y | Y | FAST40 | 80 MB 171 |895A | Y | Y | FAST40 | 80 MB/s | Y | Y |
172 +--------+-----------+-----+-----------+------ 172 +--------+-----------+-----+-----------+------------+------------+---------+
173 |896 | Y | Y | FAST40 | 80 MB 173 |896 | Y | Y | FAST40 | 80 MB/s | Y | Y |
174 +--------+-----------+-----+-----------+------ 174 +--------+-----------+-----+-----------+------------+------------+---------+
175 |897 | Y | Y | FAST40 | 80 MB 175 |897 | Y | Y | FAST40 | 80 MB/s | Y | Y |
176 +--------+-----------+-----+-----------+------ 176 +--------+-----------+-----+-----------+------------+------------+---------+
177 |1510D | Y | Y | FAST40 | 80 MB 177 |1510D | Y | Y | FAST40 | 80 MB/s | Y | Y |
178 +--------+-----------+-----+-----------+------ 178 +--------+-----------+-----+-----------+------------+------------+---------+
179 |1010 | Y | Y | FAST80 |160 MB 179 |1010 | Y | Y | FAST80 |160 MB/s | Y | Y |
180 +--------+-----------+-----+-----------+------ 180 +--------+-----------+-----+-----------+------------+------------+---------+
181 |1010_66 | Y | Y | FAST80 |160 MB 181 |1010_66 | Y | Y | FAST80 |160 MB/s | Y | Y |
182 |[1]_ | | | | 182 |[1]_ | | | | | | |
183 +--------+-----------+-----+-----------+------ 183 +--------+-----------+-----+-----------+------------+------------+---------+
184 184
185 .. [1] Chip supports 33MHz and 66MHz PCI bus c 185 .. [1] Chip supports 33MHz and 66MHz PCI bus clock.
186 186
187 187
188 Summary of other supported features: 188 Summary of other supported features:
189 189
190 :Module: allow to load the driv 190 :Module: allow to load the driver
191 :Memory mapped I/O: increases performance 191 :Memory mapped I/O: increases performance
192 :Control commands: write operations to th 192 :Control commands: write operations to the proc SCSI file system
193 :Debugging information: written to syslog (exp 193 :Debugging information: written to syslog (expert only)
194 :Serial NVRAM: Symbios and Tekram for 194 :Serial NVRAM: Symbios and Tekram formats
195 195
196 - Scatter / gather 196 - Scatter / gather
197 - Shared interrupt 197 - Shared interrupt
198 - Boot setup commands 198 - Boot setup commands
199 199
200 200
201 3. Advantages of this driver for newer chips. 201 3. Advantages of this driver for newer chips.
202 ============================================= 202 =============================================
203 203
204 3.1 Optimized SCSI SCRIPTS 204 3.1 Optimized SCSI SCRIPTS
205 -------------------------- 205 --------------------------
206 206
207 All chips except the 810, 815 and 825, support 207 All chips except the 810, 815 and 825, support new SCSI SCRIPTS instructions
208 named LOAD and STORE that allow to move up to 208 named LOAD and STORE that allow to move up to 1 DWORD from/to an IO register
209 to/from memory much faster that the MOVE MEMOR 209 to/from memory much faster that the MOVE MEMORY instruction that is supported
210 by the 53c7xx and 53c8xx family. 210 by the 53c7xx and 53c8xx family.
211 211
212 The LOAD/STORE instructions support absolute a 212 The LOAD/STORE instructions support absolute and DSA relative addressing
213 modes. The SCSI SCRIPTS had been entirely rewr 213 modes. The SCSI SCRIPTS had been entirely rewritten using LOAD/STORE instead
214 of MOVE MEMORY instructions. 214 of MOVE MEMORY instructions.
215 215
216 Due to the lack of LOAD/STORE SCRIPTS instruct 216 Due to the lack of LOAD/STORE SCRIPTS instructions by earlier chips, this
217 driver also incorporates a different SCRIPTS s 217 driver also incorporates a different SCRIPTS set based on MEMORY MOVE, in
218 order to provide support for the entire SYM53C 218 order to provide support for the entire SYM53C8XX chips family.
219 219
220 3.2 New features appeared with the SYM53C896 220 3.2 New features appeared with the SYM53C896
221 -------------------------------------------- 221 --------------------------------------------
222 222
223 Newer chips (see above) allows handling of the 223 Newer chips (see above) allows handling of the phase mismatch context from
224 SCRIPTS (avoids the phase mismatch interrupt t 224 SCRIPTS (avoids the phase mismatch interrupt that stops the SCSI processor
225 until the C code has saved the context of the 225 until the C code has saved the context of the transfer).
226 226
227 The 896 and 1010 chips support 64 bit PCI tran 227 The 896 and 1010 chips support 64 bit PCI transactions and addressing,
228 while the 895A supports 32 bit PCI transaction 228 while the 895A supports 32 bit PCI transactions and 64 bit addressing.
229 The SCRIPTS processor of these chips is not tr 229 The SCRIPTS processor of these chips is not true 64 bit, but uses segment
230 registers for bit 32-63. Another interesting f 230 registers for bit 32-63. Another interesting feature is that LOAD/STORE
231 instructions that address the on-chip RAM (8k) 231 instructions that address the on-chip RAM (8k) remain internal to the chip.
232 232
233 4. Memory mapped I/O versus normal I/O 233 4. Memory mapped I/O versus normal I/O
234 ====================================== 234 ======================================
235 235
236 Memory mapped I/O has less latency than normal 236 Memory mapped I/O has less latency than normal I/O and is the recommended
237 way for doing IO with PCI devices. Memory mapp 237 way for doing IO with PCI devices. Memory mapped I/O seems to work fine on
238 most hardware configurations, but some poorly 238 most hardware configurations, but some poorly designed chipsets may break
239 this feature. A configuration option is provid 239 this feature. A configuration option is provided for normal I/O to be
240 used but the driver defaults to MMIO. 240 used but the driver defaults to MMIO.
241 241
242 5. Tagged command queueing 242 5. Tagged command queueing
243 ========================== 243 ==========================
244 244
245 Queuing more than 1 command at a time to a dev 245 Queuing more than 1 command at a time to a device allows it to perform
246 optimizations based on actual head positions a 246 optimizations based on actual head positions and its mechanical
247 characteristics. This feature may also reduce 247 characteristics. This feature may also reduce average command latency.
248 In order to really gain advantage of this feat 248 In order to really gain advantage of this feature, devices must have
249 a reasonable cache size (No miracle is to be e 249 a reasonable cache size (No miracle is to be expected for a low-end
250 hard disk with 128 KB or less). 250 hard disk with 128 KB or less).
251 251
252 Some known old SCSI devices do not properly su 252 Some known old SCSI devices do not properly support tagged command queuing.
253 Generally, firmware revisions that fix this ki 253 Generally, firmware revisions that fix this kind of problems are available
254 at respective vendor web/ftp sites. 254 at respective vendor web/ftp sites.
255 255
256 All I can say is that I never have had problem 256 All I can say is that I never have had problem with tagged queuing using
257 this driver and its predecessors. Hard disks t 257 this driver and its predecessors. Hard disks that behaved correctly for
258 me using tagged commands are the following: 258 me using tagged commands are the following:
259 259
260 - IBM S12 0662 260 - IBM S12 0662
261 - Conner 1080S 261 - Conner 1080S
262 - Quantum Atlas I 262 - Quantum Atlas I
263 - Quantum Atlas II 263 - Quantum Atlas II
264 - Seagate Cheetah I 264 - Seagate Cheetah I
265 - Quantum Viking II 265 - Quantum Viking II
266 - IBM DRVS 266 - IBM DRVS
267 - Quantum Atlas IV 267 - Quantum Atlas IV
268 - Seagate Cheetah II 268 - Seagate Cheetah II
269 269
270 If your controller has NVRAM, you can configur 270 If your controller has NVRAM, you can configure this feature per target
271 from the user setup tool. The Tekram Setup pro 271 from the user setup tool. The Tekram Setup program allows to tune the
272 maximum number of queued commands up to 32. Th 272 maximum number of queued commands up to 32. The Symbios Setup only allows
273 to enable or disable this feature. 273 to enable or disable this feature.
274 274
275 The maximum number of simultaneous tagged comm 275 The maximum number of simultaneous tagged commands queued to a device
276 is currently set to 16 by default. This value 276 is currently set to 16 by default. This value is suitable for most SCSI
277 disks. With large SCSI disks (>= 2GB, cache > 277 disks. With large SCSI disks (>= 2GB, cache >= 512KB, average seek time
278 <= 10 ms), using a larger value may give bette 278 <= 10 ms), using a larger value may give better performances.
279 279
280 This driver supports up to 255 commands per de 280 This driver supports up to 255 commands per device, and but using more than
281 64 is generally not worth-while, unless you ar 281 64 is generally not worth-while, unless you are using a very large disk or
282 disk arrays. It is noticeable that most of rec 282 disk arrays. It is noticeable that most of recent hard disks seem not to
283 accept more than 64 simultaneous commands. So, 283 accept more than 64 simultaneous commands. So, using more than 64 queued
284 commands is probably just resource wasting. 284 commands is probably just resource wasting.
285 285
286 If your controller does not have NVRAM or if i 286 If your controller does not have NVRAM or if it is managed by the SDMS
287 BIOS/SETUP, you can configure tagged queueing 287 BIOS/SETUP, you can configure tagged queueing feature and device queue
288 depths from the boot command-line. For example 288 depths from the boot command-line. For example::
289 289
290 sym53c8xx=tags:4/t2t3q15-t4q7/t1u0q32 290 sym53c8xx=tags:4/t2t3q15-t4q7/t1u0q32
291 291
292 will set tagged commands queue depths as follo 292 will set tagged commands queue depths as follow:
293 293
294 - target 2 all luns on controller 0 --> 15 294 - target 2 all luns on controller 0 --> 15
295 - target 3 all luns on controller 0 --> 15 295 - target 3 all luns on controller 0 --> 15
296 - target 4 all luns on controller 0 --> 7 296 - target 4 all luns on controller 0 --> 7
297 - target 1 lun 0 on controller 1 --> 32 297 - target 1 lun 0 on controller 1 --> 32
298 - all other target/lun --> 4 298 - all other target/lun --> 4
299 299
300 In some special conditions, some SCSI disk fir 300 In some special conditions, some SCSI disk firmwares may return a
301 QUEUE FULL status for a SCSI command. This beh 301 QUEUE FULL status for a SCSI command. This behaviour is managed by the
302 driver using the following heuristic: 302 driver using the following heuristic:
303 303
304 - Each time a QUEUE FULL status is returned, t 304 - Each time a QUEUE FULL status is returned, tagged queue depth is reduced
305 to the actual number of disconnected command 305 to the actual number of disconnected commands.
306 306
307 - Every 200 successfully completed SCSI comman 307 - Every 200 successfully completed SCSI commands, if allowed by the
308 current limit, the maximum number of queueab 308 current limit, the maximum number of queueable commands is incremented.
309 309
310 Since QUEUE FULL status reception and handling 310 Since QUEUE FULL status reception and handling is resource wasting, the
311 driver notifies by default this problem to use 311 driver notifies by default this problem to user by indicating the actual
312 number of commands used and their status, as w 312 number of commands used and their status, as well as its decision on the
313 device queue depth change. 313 device queue depth change.
314 The heuristic used by the driver in handling Q 314 The heuristic used by the driver in handling QUEUE FULL ensures that the
315 impact on performances is not too bad. You can 315 impact on performances is not too bad. You can get rid of the messages by
316 setting verbose level to zero, as follow: 316 setting verbose level to zero, as follow:
317 317
318 1st method: 318 1st method:
319 boot your system using 'sym53c8xx= 319 boot your system using 'sym53c8xx=verb:0' option.
320 2nd method: 320 2nd method:
321 apply "setverbose 0" control comma 321 apply "setverbose 0" control command to the proc fs entry
322 corresponding to your controller a 322 corresponding to your controller after boot-up.
323 323
324 6. Parity checking 324 6. Parity checking
325 ================== 325 ==================
326 326
327 The driver supports SCSI parity checking and P 327 The driver supports SCSI parity checking and PCI bus master parity
328 checking. These features must be enabled in o 328 checking. These features must be enabled in order to ensure safe
329 data transfers. Some flawed devices or mother 329 data transfers. Some flawed devices or mother boards may have problems
330 with parity. The options to defeat parity che 330 with parity. The options to defeat parity checking have been removed
331 from the driver. 331 from the driver.
332 332
333 7. Profiling information 333 7. Profiling information
334 ======================== 334 ========================
335 335
336 This driver does not provide profiling informa 336 This driver does not provide profiling information as did its predecessors.
337 This feature was not this useful and added com 337 This feature was not this useful and added complexity to the code.
338 As the driver code got more complex, I have de 338 As the driver code got more complex, I have decided to remove everything
339 that didn't seem actually useful. 339 that didn't seem actually useful.
340 340
341 8. Control commands 341 8. Control commands
342 =================== 342 ===================
343 343
344 Control commands can be sent to the driver wit 344 Control commands can be sent to the driver with write operations to
345 the proc SCSI file system. The generic command 345 the proc SCSI file system. The generic command syntax is the
346 following:: 346 following::
347 347
348 echo "<verb> <parameters>" >/proc/scsi/s 348 echo "<verb> <parameters>" >/proc/scsi/sym53c8xx/0
349 (assumes controller number is 0) 349 (assumes controller number is 0)
350 350
351 Using "all" for "<target>" parameter with the 351 Using "all" for "<target>" parameter with the commands below will
352 apply to all targets of the SCSI chain (except 352 apply to all targets of the SCSI chain (except the controller).
353 353
354 Available commands: 354 Available commands:
355 355
356 8.1 Set minimum synchronous period factor 356 8.1 Set minimum synchronous period factor
357 ----------------------------------------- 357 -----------------------------------------
358 358
359 setsync <target> <period factor> 359 setsync <target> <period factor>
360 360
361 :target: target number 361 :target: target number
362 :period: minimum synchronous period. 362 :period: minimum synchronous period.
363 Maximum speed = 1000/(4*period 363 Maximum speed = 1000/(4*period factor) except for special
364 cases below. 364 cases below.
365 365
366 Specify a period of 0, to force asynchrono 366 Specify a period of 0, to force asynchronous transfer mode.
367 367
368 - 9 means 12.5 nano-seconds synchronous 368 - 9 means 12.5 nano-seconds synchronous period
369 - 10 means 25 nano-seconds synchronous pe 369 - 10 means 25 nano-seconds synchronous period
370 - 11 means 30 nano-seconds synchronous pe 370 - 11 means 30 nano-seconds synchronous period
371 - 12 means 50 nano-seconds synchronous pe 371 - 12 means 50 nano-seconds synchronous period
372 372
373 8.2 Set wide size 373 8.2 Set wide size
374 ----------------- 374 -----------------
375 375
376 setwide <target> <size> 376 setwide <target> <size>
377 377
378 :target: target number 378 :target: target number
379 :size: 0=8 bits, 1=16bits 379 :size: 0=8 bits, 1=16bits
380 380
381 8.3 Set maximum number of concurrent tagged co 381 8.3 Set maximum number of concurrent tagged commands
382 ---------------------------------------------- 382 ----------------------------------------------------
383 383
384 settags <target> <tags> 384 settags <target> <tags>
385 385
386 :target: target number 386 :target: target number
387 :tags: number of concurrent tagged com 387 :tags: number of concurrent tagged commands
388 must not be greater than config 388 must not be greater than configured (default: 16)
389 389
390 8.4 Set debug mode 390 8.4 Set debug mode
391 ------------------ 391 ------------------
392 392
393 setdebug <list of debug flags> 393 setdebug <list of debug flags>
394 394
395 Available debug flags: 395 Available debug flags:
396 396
397 ======== ============================= 397 ======== ========================================================
398 alloc print info about memory alloc 398 alloc print info about memory allocations (ccb, lcb)
399 queue print info about insertions i 399 queue print info about insertions into the command start queue
400 result print sense data on CHECK CON 400 result print sense data on CHECK CONDITION status
401 scatter print info about the scatter 401 scatter print info about the scatter process
402 scripts print info about the script b 402 scripts print info about the script binding process
403 tiny print minimal debugging infor 403 tiny print minimal debugging information
404 timing print timing information of t 404 timing print timing information of the NCR chip
405 nego print information about SCSI 405 nego print information about SCSI negotiations
406 phase print information on script i 406 phase print information on script interruptions
407 ======== ============================= 407 ======== ========================================================
408 408
409 Use "setdebug" with no argument to reset d 409 Use "setdebug" with no argument to reset debug flags.
410 410
411 411
412 8.5 Set flag (no_disc) 412 8.5 Set flag (no_disc)
413 ---------------------- 413 ----------------------
414 414
415 setflag <target> <flag> 415 setflag <target> <flag>
416 416
417 :target: target number 417 :target: target number
418 418
419 For the moment, only one flag is available 419 For the moment, only one flag is available:
420 420
421 no_disc: not allow target to disconn 421 no_disc: not allow target to disconnect.
422 422
423 Do not specify any flag in order to reset 423 Do not specify any flag in order to reset the flag. For example:
424 424
425 setflag 4 425 setflag 4
426 will reset no_disc flag for target 4, so 426 will reset no_disc flag for target 4, so will allow it disconnections.
427 setflag all 427 setflag all
428 will allow disconnection for all devices 428 will allow disconnection for all devices on the SCSI bus.
429 429
430 430
431 8.6 Set verbose level 431 8.6 Set verbose level
432 --------------------- 432 ---------------------
433 433
434 setverbose #level 434 setverbose #level
435 435
436 The driver default verbose level is 1. Thi 436 The driver default verbose level is 1. This command allows to change
437 th driver verbose level after boot-up. 437 th driver verbose level after boot-up.
438 438
439 8.7 Reset all logical units of a target 439 8.7 Reset all logical units of a target
440 --------------------------------------- 440 ---------------------------------------
441 441
442 resetdev <target> 442 resetdev <target>
443 443
444 :target: target number 444 :target: target number
445 445
446 The driver will try to send a BUS DEVICE R 446 The driver will try to send a BUS DEVICE RESET message to the target.
447 447
448 8.8 Abort all tasks of all logical units of a 448 8.8 Abort all tasks of all logical units of a target
449 ---------------------------------------------- 449 ----------------------------------------------------
450 450
451 cleardev <target> 451 cleardev <target>
452 452
453 :target: target number 453 :target: target number
454 454
455 The driver will try to send a ABORT messag 455 The driver will try to send a ABORT message to all the logical units
456 of the target. 456 of the target.
457 457
458 458
459 9. Configuration parameters 459 9. Configuration parameters
460 =========================== 460 ===========================
461 461
462 Under kernel configuration tools (make menucon 462 Under kernel configuration tools (make menuconfig, for example), it is
463 possible to change some default driver configu 463 possible to change some default driver configuration parameters.
464 If the firmware of all your devices is perfect 464 If the firmware of all your devices is perfect enough, all the
465 features supported by the driver can be enable 465 features supported by the driver can be enabled at start-up. However,
466 if only one has a flaw for some SCSI feature, 466 if only one has a flaw for some SCSI feature, you can disable the
467 support by the driver of this feature at linux 467 support by the driver of this feature at linux start-up and enable
468 this feature after boot-up only for devices th 468 this feature after boot-up only for devices that support it safely.
469 469
470 Configuration parameters: 470 Configuration parameters:
471 471
472 Use normal IO (default 472 Use normal IO (default answer: n)
473 Answer "y" if you suspect your mother boar 473 Answer "y" if you suspect your mother board to not allow memory mapped I/O.
474 May slow down performance a little. 474 May slow down performance a little.
475 475
476 Default tagged command queue depth (default 476 Default tagged command queue depth (default answer: 16)
477 Entering 0 defaults to tagged commands not 477 Entering 0 defaults to tagged commands not being used.
478 This parameter can be specified from the b 478 This parameter can be specified from the boot command line.
479 479
480 Maximum number of queued commands (default 480 Maximum number of queued commands (default answer: 32)
481 This option allows you to specify the maxi 481 This option allows you to specify the maximum number of tagged commands
482 that can be queued to a device. The maximu 482 that can be queued to a device. The maximum supported value is 255.
483 483
484 Synchronous transfers frequency (default 484 Synchronous transfers frequency (default answer: 80)
485 This option allows you to specify the freq 485 This option allows you to specify the frequency in MHz the driver
486 will use at boot time for synchronous data 486 will use at boot time for synchronous data transfer negotiations.
487 0 means "asynchronous data transfers". 487 0 means "asynchronous data transfers".
488 488
489 10. Boot setup commands 489 10. Boot setup commands
490 ======================= 490 =======================
491 491
492 10.1 Syntax 492 10.1 Syntax
493 ----------- 493 -----------
494 494
495 Setup commands can be passed to the driver eit 495 Setup commands can be passed to the driver either at boot time or as
496 parameters to modprobe, as described in Docume 496 parameters to modprobe, as described in Documentation/admin-guide/kernel-parameters.rst
497 497
498 Example of boot setup command under lilo promp 498 Example of boot setup command under lilo prompt::
499 499
500 lilo: linux root=/dev/sda2 sym53c8xx.cmd_p 500 lilo: linux root=/dev/sda2 sym53c8xx.cmd_per_lun=4 sym53c8xx.sync=10 sym53c8xx.debug=0x200
501 501
502 - enable tagged commands, up to 4 tagged comma 502 - enable tagged commands, up to 4 tagged commands queued.
503 - set synchronous negotiation speed to 10 Mega 503 - set synchronous negotiation speed to 10 Mega-transfers / second.
504 - set DEBUG_NEGO flag. 504 - set DEBUG_NEGO flag.
505 505
506 The following command will install the driver 506 The following command will install the driver module with the same
507 options as above:: 507 options as above::
508 508
509 modprobe sym53c8xx cmd_per_lun=4 sync=10 d 509 modprobe sym53c8xx cmd_per_lun=4 sync=10 debug=0x200
510 510
511 10.2 Available arguments 511 10.2 Available arguments
512 ------------------------ 512 ------------------------
513 513
514 10.2.1 Default number of tagged commands 514 10.2.1 Default number of tagged commands
515 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 515 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
516 - cmd_per_lun=0 (or cmd_per_lun=1) tag 516 - cmd_per_lun=0 (or cmd_per_lun=1) tagged command queuing disabled
517 - cmd_per_lun=#tags (#tags > 1) tagged 517 - cmd_per_lun=#tags (#tags > 1) tagged command queuing enabled
518 518
519 #tags will be truncated to the max queued co 519 #tags will be truncated to the max queued commands configuration parameter.
520 520
521 10.2.2 Burst max 521 10.2.2 Burst max
522 ^^^^^^^^^^^^^^^^ 522 ^^^^^^^^^^^^^^^^
523 523
524 ========== =========================== 524 ========== ======================================================
525 burst=0 burst disabled 525 burst=0 burst disabled
526 burst=255 get burst length from initi 526 burst=255 get burst length from initial IO register settings.
527 burst=#x burst enabled (1<<#x burst 527 burst=#x burst enabled (1<<#x burst transfers max)
528 528
529 #x is an integer value whic 529 #x is an integer value which is log base 2 of the burst
530 transfers max. 530 transfers max.
531 ========== =========================== 531 ========== ======================================================
532 532
533 By default the driver uses the maximum value 533 By default the driver uses the maximum value supported by the chip.
534 534
535 10.2.3 LED support 535 10.2.3 LED support
536 ^^^^^^^^^^^^^^^^^^ 536 ^^^^^^^^^^^^^^^^^^
537 537
538 ===== =================== 538 ===== ===================
539 led=1 enable LED support 539 led=1 enable LED support
540 led=0 disable LED support 540 led=0 disable LED support
541 ===== =================== 541 ===== ===================
542 542
543 Do not enable LED support if your scsi board 543 Do not enable LED support if your scsi board does not use SDMS BIOS.
544 (See 'Configuration parameters') 544 (See 'Configuration parameters')
545 545
546 10.2.4 Differential mode 546 10.2.4 Differential mode
547 ^^^^^^^^^^^^^^^^^^^^^^^^ 547 ^^^^^^^^^^^^^^^^^^^^^^^^
548 548
549 ====== ============================== 549 ====== =================================
550 diff=0 never set up diff mode 550 diff=0 never set up diff mode
551 diff=1 set up diff mode if BIOS set i 551 diff=1 set up diff mode if BIOS set it
552 diff=2 always set up diff mode 552 diff=2 always set up diff mode
553 diff=3 set diff mode if GPIO3 is not 553 diff=3 set diff mode if GPIO3 is not set
554 ====== ============================== 554 ====== =================================
555 555
556 10.2.5 IRQ mode 556 10.2.5 IRQ mode
557 ^^^^^^^^^^^^^^^ 557 ^^^^^^^^^^^^^^^
558 558
559 ====== =========================== 559 ====== ================================================
560 irqm=0 always open drain 560 irqm=0 always open drain
561 irqm=1 same as initial settings (a 561 irqm=1 same as initial settings (assumed BIOS settings)
562 irqm=2 always totem pole 562 irqm=2 always totem pole
563 ====== =========================== 563 ====== ================================================
564 564
565 10.2.6 Check SCSI BUS 565 10.2.6 Check SCSI BUS
566 ^^^^^^^^^^^^^^^^^^^^^ 566 ^^^^^^^^^^^^^^^^^^^^^
567 567
568 buschk=<option bits> 568 buschk=<option bits>
569 569
570 Available option bits: 570 Available option bits:
571 571
572 === =============================== 572 === ================================================
573 0x0 No check. 573 0x0 No check.
574 0x1 Check and do not attach the con 574 0x1 Check and do not attach the controller on error.
575 0x2 Check and just warn on error. 575 0x2 Check and just warn on error.
576 === =============================== 576 === ================================================
577 577
578 10.2.7 Suggest a default SCSI id for hosts 578 10.2.7 Suggest a default SCSI id for hosts
579 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 579 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
580 580
581 ========== ====================== 581 ========== ==========================================
582 hostid=255 no id suggested. 582 hostid=255 no id suggested.
583 hostid=#x (0 < x < 7) x suggeste 583 hostid=#x (0 < x < 7) x suggested for hosts SCSI id.
584 ========== ====================== 584 ========== ==========================================
585 585
586 If a host SCSI id is available from the NV 586 If a host SCSI id is available from the NVRAM, the driver will ignore
587 any value suggested as boot option. Otherw 587 any value suggested as boot option. Otherwise, if a suggested value
588 different from 255 has been supplied, it w 588 different from 255 has been supplied, it will use it. Otherwise, it will
589 try to deduce the value previously set in 589 try to deduce the value previously set in the hardware and use value
590 7 if the hardware value is zero. 590 7 if the hardware value is zero.
591 591
592 10.2.8 Verbosity level 592 10.2.8 Verbosity level
593 ^^^^^^^^^^^^^^^^^^^^^^^ 593 ^^^^^^^^^^^^^^^^^^^^^^^
594 594
595 ====== ======== 595 ====== ========
596 verb=0 minimal 596 verb=0 minimal
597 verb=1 normal 597 verb=1 normal
598 verb=2 too much 598 verb=2 too much
599 ====== ======== 599 ====== ========
600 600
601 10.2.9 Debug mode 601 10.2.9 Debug mode
602 ^^^^^^^^^^^^^^^^^ 602 ^^^^^^^^^^^^^^^^^
603 603
604 ========= ========================== 604 ========= ====================================
605 debug=0 clear debug flags 605 debug=0 clear debug flags
606 debug=#x set debug flags 606 debug=#x set debug flags
607 607
608 #x is an integer value com 608 #x is an integer value combining the
609 following power-of-2 value 609 following power-of-2 values:
610 610
611 ============= ====== 611 ============= ======
612 DEBUG_ALLOC 0x1 612 DEBUG_ALLOC 0x1
613 DEBUG_PHASE 0x2 613 DEBUG_PHASE 0x2
614 DEBUG_POLL 0x4 614 DEBUG_POLL 0x4
615 DEBUG_QUEUE 0x8 615 DEBUG_QUEUE 0x8
616 DEBUG_RESULT 0x10 616 DEBUG_RESULT 0x10
617 DEBUG_SCATTER 0x20 617 DEBUG_SCATTER 0x20
618 DEBUG_SCRIPT 0x40 618 DEBUG_SCRIPT 0x40
619 DEBUG_TINY 0x80 619 DEBUG_TINY 0x80
620 DEBUG_TIMING 0x100 620 DEBUG_TIMING 0x100
621 DEBUG_NEGO 0x200 621 DEBUG_NEGO 0x200
622 DEBUG_TAGS 0x400 622 DEBUG_TAGS 0x400
623 DEBUG_FREEZE 0x800 623 DEBUG_FREEZE 0x800
624 DEBUG_RESTART 0x1000 624 DEBUG_RESTART 0x1000
625 ============= ====== 625 ============= ======
626 ========= ========================== 626 ========= ====================================
627 627
628 You can play safely with DEBUG_NEGO. However 628 You can play safely with DEBUG_NEGO. However, some of these flags may
629 generate bunches of syslog messages. 629 generate bunches of syslog messages.
630 630
631 10.2.10 Settle delay 631 10.2.10 Settle delay
632 ^^^^^^^^^^^^^^^^^^^^ 632 ^^^^^^^^^^^^^^^^^^^^
633 633
634 ======== =================== 634 ======== ===================
635 settle=n delay for n seconds 635 settle=n delay for n seconds
636 ======== =================== 636 ======== ===================
637 637
638 After a bus reset, the driver will delay for 638 After a bus reset, the driver will delay for n seconds before talking
639 to any device on the bus. The default is 3 639 to any device on the bus. The default is 3 seconds and safe mode will
640 default it to 10. 640 default it to 10.
641 641
642 10.2.11 Serial NVRAM 642 10.2.11 Serial NVRAM
643 ^^^^^^^^^^^^^^^^^^^^ 643 ^^^^^^^^^^^^^^^^^^^^
644 644
645 .. Note:: option not currently impleme 645 .. Note:: option not currently implemented.
646 646
647 ======= ========================== 647 ======= =========================================
648 nvram=n do not look for serial NVR 648 nvram=n do not look for serial NVRAM
649 nvram=y test controllers for onboa 649 nvram=y test controllers for onboard serial NVRAM
650 ======= ========================== 650 ======= =========================================
651 651
652 (alternate binary form) 652 (alternate binary form)
653 653
654 nvram=<bits options> 654 nvram=<bits options>
655 655
656 ==== =============================== 656 ==== =================================================================
657 0x01 look for NVRAM (equivalent to 657 0x01 look for NVRAM (equivalent to nvram=y)
658 0x02 ignore NVRAM "Synchronous negot 658 0x02 ignore NVRAM "Synchronous negotiation" parameters for all devices
659 0x04 ignore NVRAM "Wide negotiation" 659 0x04 ignore NVRAM "Wide negotiation" parameter for all devices
660 0x08 ignore NVRAM "Scan at boot time 660 0x08 ignore NVRAM "Scan at boot time" parameter for all devices
661 0x80 also attach controllers set to 661 0x80 also attach controllers set to OFF in the NVRAM (sym53c8xx only)
662 ==== =============================== 662 ==== =================================================================
663 663
664 10.2.12 Exclude a host from being attached 664 10.2.12 Exclude a host from being attached
665 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ 665 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
666 666
667 excl=<io_address>,... 667 excl=<io_address>,...
668 668
669 Prevent host at a given io address from be 669 Prevent host at a given io address from being attached.
670 For example 'excl=0xb400,0xc000' indicate 670 For example 'excl=0xb400,0xc000' indicate to the
671 driver not to attach hosts at address 0xb4 671 driver not to attach hosts at address 0xb400 and 0xc000.
672 672
673 10.3 Converting from old style options 673 10.3 Converting from old style options
674 -------------------------------------- 674 --------------------------------------
675 675
676 Previously, the sym2 driver accepted arguments 676 Previously, the sym2 driver accepted arguments of the form::
677 677
678 sym53c8xx=tags:4,sync:10,debug:0x200 678 sym53c8xx=tags:4,sync:10,debug:0x200
679 679
680 As a result of the new module parameters, this 680 As a result of the new module parameters, this is no longer available.
681 Most of the options have remained the same, bu 681 Most of the options have remained the same, but tags has become
682 cmd_per_lun to reflect its different purposes. 682 cmd_per_lun to reflect its different purposes. The sample above would
683 be specified as:: 683 be specified as::
684 684
685 modprobe sym53c8xx cmd_per_lun=4 sync= 685 modprobe sym53c8xx cmd_per_lun=4 sync=10 debug=0x200
686 686
687 or on the kernel boot line as:: 687 or on the kernel boot line as::
688 688
689 sym53c8xx.cmd_per_lun=4 sym53c8xx.sync 689 sym53c8xx.cmd_per_lun=4 sym53c8xx.sync=10 sym53c8xx.debug=0x200
690 690
691 10.4 SCSI BUS checking boot option 691 10.4 SCSI BUS checking boot option
692 ---------------------------------- 692 ----------------------------------
693 693
694 When this option is set to a non-zero value, t 694 When this option is set to a non-zero value, the driver checks SCSI lines
695 logic state, 100 micro-seconds after having as 695 logic state, 100 micro-seconds after having asserted the SCSI RESET line.
696 The driver just reads SCSI lines and checks al 696 The driver just reads SCSI lines and checks all lines read FALSE except RESET.
697 Since SCSI devices shall release the BUS at mo 697 Since SCSI devices shall release the BUS at most 800 nano-seconds after SCSI
698 RESET has been asserted, any signal to TRUE ma 698 RESET has been asserted, any signal to TRUE may indicate a SCSI BUS problem.
699 Unfortunately, the following common SCSI BUS p 699 Unfortunately, the following common SCSI BUS problems are not detected:
700 700
701 - Only 1 terminator installed. 701 - Only 1 terminator installed.
702 - Misplaced terminators. 702 - Misplaced terminators.
703 - Bad quality terminators. 703 - Bad quality terminators.
704 704
705 On the other hand, either bad cabling, broken 705 On the other hand, either bad cabling, broken devices, not conformant
706 devices, ... may cause a SCSI signal to be wro 706 devices, ... may cause a SCSI signal to be wrong when the driver reads it.
707 707
708 15. SCSI problem troubleshooting 708 15. SCSI problem troubleshooting
709 ================================ 709 ================================
710 710
711 15.1 Problem tracking 711 15.1 Problem tracking
712 --------------------- 712 ---------------------
713 713
714 Most SCSI problems are due to a non conformant 714 Most SCSI problems are due to a non conformant SCSI bus or too buggy
715 devices. If unfortunately you have SCSI probl 715 devices. If unfortunately you have SCSI problems, you can check the
716 following things: 716 following things:
717 717
718 - SCSI bus cables 718 - SCSI bus cables
719 - terminations at both end of the SCSI chain 719 - terminations at both end of the SCSI chain
720 - linux syslog messages (some of them may help 720 - linux syslog messages (some of them may help you)
721 721
722 If you do not find the source of problems, you 722 If you do not find the source of problems, you can configure the
723 driver or devices in the NVRAM with minimal fe 723 driver or devices in the NVRAM with minimal features.
724 724
725 - only asynchronous data transfers 725 - only asynchronous data transfers
726 - tagged commands disabled 726 - tagged commands disabled
727 - disconnections not allowed 727 - disconnections not allowed
728 728
729 Now, if your SCSI bus is ok, your system has e 729 Now, if your SCSI bus is ok, your system has every chance to work
730 with this safe configuration but performances 730 with this safe configuration but performances will not be optimal.
731 731
732 If it still fails, then you can send your prob 732 If it still fails, then you can send your problem description to
733 appropriate mailing lists or news-groups. Sen 733 appropriate mailing lists or news-groups. Send me a copy in order to
734 be sure I will receive it. Obviously, a bug i 734 be sure I will receive it. Obviously, a bug in the driver code is
735 possible. 735 possible.
736 736
737 My current email address: Gerard Roudier <gro 737 My current email address: Gerard Roudier <groudier@free.fr>
738 738
739 Allowing disconnections is important if you us 739 Allowing disconnections is important if you use several devices on
740 your SCSI bus but often causes problems with b 740 your SCSI bus but often causes problems with buggy devices.
741 Synchronous data transfers increases throughpu 741 Synchronous data transfers increases throughput of fast devices like
742 hard disks. Good SCSI hard disks with a large 742 hard disks. Good SCSI hard disks with a large cache gain advantage of
743 tagged commands queuing. 743 tagged commands queuing.
744 744
745 15.2 Understanding hardware error reports 745 15.2 Understanding hardware error reports
746 ----------------------------------------- 746 -----------------------------------------
747 747
748 When the driver detects an unexpected error co 748 When the driver detects an unexpected error condition, it may display a
749 message of the following pattern:: 749 message of the following pattern::
750 750
751 sym0:1: ERROR (0:48) (1-21-65) (f/95/0) @ 751 sym0:1: ERROR (0:48) (1-21-65) (f/95/0) @ (script 7c0:19000000).
752 sym0: script cmd = 19000000 752 sym0: script cmd = 19000000
753 sym0: regdump: da 10 80 95 47 0f 01 07 75 753 sym0: regdump: da 10 80 95 47 0f 01 07 75 01 81 21 80 01 09 00.
754 754
755 Some fields in such a message may help you und 755 Some fields in such a message may help you understand the cause of the
756 problem, as follows:: 756 problem, as follows::
757 757
758 sym0:1: ERROR (0:48) (1-21-65) (f/95/0) @ 758 sym0:1: ERROR (0:48) (1-21-65) (f/95/0) @ (script 7c0:19000000).
759 .....A.........B.C....D.E..F....G.H..I.... 759 .....A.........B.C....D.E..F....G.H..I.......J.....K...L.......
760 760
761 Field A : target number. 761 Field A : target number.
762 SCSI ID of the device the controller was tal 762 SCSI ID of the device the controller was talking with at the moment the
763 error occurs. 763 error occurs.
764 764
765 Field B : DSTAT io register (DMA STATUS) 765 Field B : DSTAT io register (DMA STATUS)
766 ======== ================================= 766 ======== =============================================================
767 Bit 0x40 MDPE Master Data Parity Error 767 Bit 0x40 MDPE Master Data Parity Error
768 Data parity error detected on the 768 Data parity error detected on the PCI BUS.
769 Bit 0x20 BF Bus Fault 769 Bit 0x20 BF Bus Fault
770 PCI bus fault condition detected 770 PCI bus fault condition detected
771 Bit 0x01 IID Illegal Instruction Detected 771 Bit 0x01 IID Illegal Instruction Detected
772 Set by the chip when it detects a 772 Set by the chip when it detects an Illegal Instruction format
773 on some condition that makes an i 773 on some condition that makes an instruction illegal.
774 Bit 0x80 DFE Dma Fifo Empty 774 Bit 0x80 DFE Dma Fifo Empty
775 Pure status bit that does not ind 775 Pure status bit that does not indicate an error.
776 ======== ================================= 776 ======== =============================================================
777 777
778 If the reported DSTAT value contains a combi 778 If the reported DSTAT value contains a combination of MDPE (0x40),
779 BF (0x20), then the cause may be likely due 779 BF (0x20), then the cause may be likely due to a PCI BUS problem.
780 780
781 Field C : SIST io register (SCSI Interrupt Sta 781 Field C : SIST io register (SCSI Interrupt Status)
782 ======== ================================= 782 ======== ==================================================================
783 Bit 0x08 SGE SCSI GROSS ERROR 783 Bit 0x08 SGE SCSI GROSS ERROR
784 Indicates that the chip detected 784 Indicates that the chip detected a severe error condition
785 on the SCSI BUS that prevents the 785 on the SCSI BUS that prevents the SCSI protocol from functioning
786 properly. 786 properly.
787 Bit 0x04 UDC Unexpected Disconnection 787 Bit 0x04 UDC Unexpected Disconnection
788 Indicates that the device release 788 Indicates that the device released the SCSI BUS when the chip
789 was not expecting this to happen. 789 was not expecting this to happen. A device may behave so to
790 indicate the SCSI initiator that 790 indicate the SCSI initiator that an error condition not reportable using the SCSI protocol has occurred.
791 Bit 0x02 RST SCSI BUS Reset 791 Bit 0x02 RST SCSI BUS Reset
792 Generally SCSI targets do not res 792 Generally SCSI targets do not reset the SCSI BUS, although any
793 device on the BUS can reset it at 793 device on the BUS can reset it at any time.
794 Bit 0x01 PAR Parity 794 Bit 0x01 PAR Parity
795 SCSI parity error detected. 795 SCSI parity error detected.
796 ======== ================================= 796 ======== ==================================================================
797 797
798 On a faulty SCSI BUS, any error condition am 798 On a faulty SCSI BUS, any error condition among SGE (0x08), UDC (0x04) and
799 PAR (0x01) may be detected by the chip. If y 799 PAR (0x01) may be detected by the chip. If your SCSI system sometimes
800 encounters such error conditions, especially 800 encounters such error conditions, especially SCSI GROSS ERROR, then a SCSI
801 BUS problem is likely the cause of these err 801 BUS problem is likely the cause of these errors.
802 802
803 For fields D,E,F,G and H, you may look into th 803 For fields D,E,F,G and H, you may look into the sym53c8xx_defs.h file
804 that contains some minimal comments on IO regi 804 that contains some minimal comments on IO register bits.
805 805
806 Field D : SOCL Scsi Output Control Latch 806 Field D : SOCL Scsi Output Control Latch
807 This register reflects the state of 807 This register reflects the state of the SCSI control lines the
808 chip want to drive or compare agains 808 chip want to drive or compare against.
809 Field E : SBCL Scsi Bus Control Lines 809 Field E : SBCL Scsi Bus Control Lines
810 Actual value of control lines on the 810 Actual value of control lines on the SCSI BUS.
811 Field F : SBDL Scsi Bus Data Lines 811 Field F : SBDL Scsi Bus Data Lines
812 Actual value of data lines on the SC 812 Actual value of data lines on the SCSI BUS.
813 Field G : SXFER SCSI Transfer 813 Field G : SXFER SCSI Transfer
814 Contains the setting of the Synchron 814 Contains the setting of the Synchronous Period for output and
815 the current Synchronous offset (offs 815 the current Synchronous offset (offset 0 means asynchronous).
816 Field H : SCNTL3 Scsi Control Register 3 816 Field H : SCNTL3 Scsi Control Register 3
817 Contains the setting of timing value 817 Contains the setting of timing values for both asynchronous and
818 synchronous data transfers. 818 synchronous data transfers.
819 Field I : SCNTL4 Scsi Control Register 4 819 Field I : SCNTL4 Scsi Control Register 4
820 Only meaningful for 53C1010 Ultra3 c 820 Only meaningful for 53C1010 Ultra3 controllers.
821 821
822 Understanding Fields J, K, L and dumps require 822 Understanding Fields J, K, L and dumps requires to have good knowledge of
823 SCSI standards, chip cores functionnals and in 823 SCSI standards, chip cores functionnals and internal driver data structures.
824 You are not required to decode and understand 824 You are not required to decode and understand them, unless you want to help
825 maintain the driver code. 825 maintain the driver code.
826 826
827 17. Serial NVRAM (added by Richard Waltham: do 827 17. Serial NVRAM (added by Richard Waltham: dormouse@farsrobt.demon.co.uk)
828 ============================================== 828 ==========================================================================
829 829
830 17.1 Features 830 17.1 Features
831 ------------- 831 -------------
832 832
833 Enabling serial NVRAM support enables detectio 833 Enabling serial NVRAM support enables detection of the serial NVRAM included
834 on Symbios and some Symbios compatible host ad 834 on Symbios and some Symbios compatible host adaptors, and Tekram boards. The
835 serial NVRAM is used by Symbios and Tekram to 835 serial NVRAM is used by Symbios and Tekram to hold set up parameters for the
836 host adaptor and its attached drives. 836 host adaptor and its attached drives.
837 837
838 The Symbios NVRAM also holds data on the boot 838 The Symbios NVRAM also holds data on the boot order of host adaptors in a
839 system with more than one host adaptor. This 839 system with more than one host adaptor. This information is no longer used
840 as it's fundamentally incompatible with the ho 840 as it's fundamentally incompatible with the hotplug PCI model.
841 841
842 Tekram boards using Symbios chips, DC390W/F/U, 842 Tekram boards using Symbios chips, DC390W/F/U, which have NVRAM are detected
843 and this is used to distinguish between Symbio 843 and this is used to distinguish between Symbios compatible and Tekram host
844 adaptors. This is used to disable the Symbios 844 adaptors. This is used to disable the Symbios compatible "diff" setting
845 incorrectly set on Tekram boards if the CONFIG 845 incorrectly set on Tekram boards if the CONFIG_SCSI_53C8XX_SYMBIOS_COMPAT
846 configuration parameter is set enabling both S 846 configuration parameter is set enabling both Symbios and Tekram boards to be
847 used together with the Symbios cards using all 847 used together with the Symbios cards using all their features, including
848 "diff" support. ("led pin" support for Symbios 848 "diff" support. ("led pin" support for Symbios compatible cards can remain
849 enabled when using Tekram cards. It does nothi 849 enabled when using Tekram cards. It does nothing useful for Tekram host
850 adaptors but does not cause problems either.) 850 adaptors but does not cause problems either.)
851 851
852 The parameters the driver is able to get from 852 The parameters the driver is able to get from the NVRAM depend on the
853 data format used, as follow: 853 data format used, as follow:
854 854
855 +-------------------------------+------------- 855 +-------------------------------+------------------+--------------+
856 | |Tekram format 856 | |Tekram format |Symbios format|
857 +-------------------------------+------------- 857 +-------------------------------+------------------+--------------+
858 |General and host parameters | 858 |General and host parameters | | |
859 +-------------------------------+------------- 859 +-------------------------------+------------------+--------------+
860 | * Boot order | N 860 | * Boot order | N | Y |
861 +-------------------------------+------------- 861 +-------------------------------+------------------+--------------+
862 | * Host SCSI ID | Y 862 | * Host SCSI ID | Y | Y |
863 +-------------------------------+------------- 863 +-------------------------------+------------------+--------------+
864 | * SCSI parity checking | Y 864 | * SCSI parity checking | Y | Y |
865 +-------------------------------+------------- 865 +-------------------------------+------------------+--------------+
866 | * Verbose boot messages | N 866 | * Verbose boot messages | N | Y |
867 +-------------------------------+------------- 867 +-------------------------------+------------------+--------------+
868 |SCSI devices parameters 868 |SCSI devices parameters |
869 +-------------------------------+------------- 869 +-------------------------------+------------------+--------------+
870 | * Synchronous transfer speed | Y 870 | * Synchronous transfer speed | Y | Y |
871 +-------------------------------+------------- 871 +-------------------------------+------------------+--------------+
872 | * Wide 16 / Narrow | Y 872 | * Wide 16 / Narrow | Y | Y |
873 +-------------------------------+------------- 873 +-------------------------------+------------------+--------------+
874 | * Tagged Command Queuing | Y 874 | * Tagged Command Queuing | Y | Y |
875 | enabled | 875 | enabled | | |
876 +-------------------------------+------------- 876 +-------------------------------+------------------+--------------+
877 | * Disconnections enabled | Y 877 | * Disconnections enabled | Y | Y |
878 +-------------------------------+------------- 878 +-------------------------------+------------------+--------------+
879 | * Scan at boot time | N 879 | * Scan at boot time | N | Y |
880 +-------------------------------+------------- 880 +-------------------------------+------------------+--------------+
881 881
882 882
883 In order to speed up the system boot, for each 883 In order to speed up the system boot, for each device configured without
884 the "scan at boot time" option, the driver for 884 the "scan at boot time" option, the driver forces an error on the
885 first TEST UNIT READY command received for thi 885 first TEST UNIT READY command received for this device.
886 886
887 887
888 17.2 Symbios NVRAM layout 888 17.2 Symbios NVRAM layout
889 ------------------------- 889 -------------------------
890 890
891 typical data at NVRAM address 0x100 (53c810a N 891 typical data at NVRAM address 0x100 (53c810a NVRAM)::
892 892
893 00 00 893 00 00
894 64 01 894 64 01
895 8e 0b 895 8e 0b
896 896
897 00 30 00 00 00 00 07 00 00 00 00 00 00 00 897 00 30 00 00 00 00 07 00 00 00 00 00 00 00 07 04 10 04 00 00
898 898
899 04 00 0f 00 00 10 00 50 00 00 01 00 00 62 899 04 00 0f 00 00 10 00 50 00 00 01 00 00 62
900 04 00 03 00 00 10 00 58 00 00 01 00 00 63 900 04 00 03 00 00 10 00 58 00 00 01 00 00 63
901 04 00 01 00 00 10 00 48 00 00 01 00 00 61 901 04 00 01 00 00 10 00 48 00 00 01 00 00 61
902 00 00 00 00 00 00 00 00 00 00 00 00 00 00 902 00 00 00 00 00 00 00 00 00 00 00 00 00 00
903 903
904 0f 00 08 08 64 00 0a 00 904 0f 00 08 08 64 00 0a 00
905 0f 00 08 08 64 00 0a 00 905 0f 00 08 08 64 00 0a 00
906 0f 00 08 08 64 00 0a 00 906 0f 00 08 08 64 00 0a 00
907 0f 00 08 08 64 00 0a 00 907 0f 00 08 08 64 00 0a 00
908 0f 00 08 08 64 00 0a 00 908 0f 00 08 08 64 00 0a 00
909 0f 00 08 08 64 00 0a 00 909 0f 00 08 08 64 00 0a 00
910 0f 00 08 08 64 00 0a 00 910 0f 00 08 08 64 00 0a 00
911 0f 00 08 08 64 00 0a 00 911 0f 00 08 08 64 00 0a 00
912 912
913 0f 00 08 08 64 00 0a 00 913 0f 00 08 08 64 00 0a 00
914 0f 00 08 08 64 00 0a 00 914 0f 00 08 08 64 00 0a 00
915 0f 00 08 08 64 00 0a 00 915 0f 00 08 08 64 00 0a 00
916 0f 00 08 08 64 00 0a 00 916 0f 00 08 08 64 00 0a 00
917 0f 00 08 08 64 00 0a 00 917 0f 00 08 08 64 00 0a 00
918 0f 00 08 08 64 00 0a 00 918 0f 00 08 08 64 00 0a 00
919 0f 00 08 08 64 00 0a 00 919 0f 00 08 08 64 00 0a 00
920 0f 00 08 08 64 00 0a 00 920 0f 00 08 08 64 00 0a 00
921 921
922 00 00 00 00 00 00 00 00 922 00 00 00 00 00 00 00 00
923 00 00 00 00 00 00 00 00 923 00 00 00 00 00 00 00 00
924 00 00 00 00 00 00 00 00 924 00 00 00 00 00 00 00 00
925 00 00 00 00 00 00 00 00 925 00 00 00 00 00 00 00 00
926 00 00 00 00 00 00 00 00 926 00 00 00 00 00 00 00 00
927 00 00 00 00 00 00 00 00 927 00 00 00 00 00 00 00 00
928 00 00 00 00 00 00 00 00 928 00 00 00 00 00 00 00 00
929 00 00 00 00 00 00 00 00 929 00 00 00 00 00 00 00 00
930 930
931 00 00 00 00 00 00 00 00 931 00 00 00 00 00 00 00 00
932 00 00 00 00 00 00 00 00 932 00 00 00 00 00 00 00 00
933 00 00 00 00 00 00 00 00 933 00 00 00 00 00 00 00 00
934 00 00 00 00 00 00 00 00 934 00 00 00 00 00 00 00 00
935 00 00 00 00 00 00 00 00 935 00 00 00 00 00 00 00 00
936 00 00 00 00 00 00 00 00 936 00 00 00 00 00 00 00 00
937 00 00 00 00 00 00 00 00 937 00 00 00 00 00 00 00 00
938 00 00 00 00 00 00 00 00 938 00 00 00 00 00 00 00 00
939 939
940 00 00 00 00 00 00 00 00 940 00 00 00 00 00 00 00 00
941 00 00 00 00 00 00 00 00 941 00 00 00 00 00 00 00 00
942 00 00 00 00 00 00 00 00 942 00 00 00 00 00 00 00 00
943 943
944 fe fe 944 fe fe
945 00 00 945 00 00
946 00 00 946 00 00
947 947
948 NVRAM layout details 948 NVRAM layout details
949 949
950 ============= ================= 950 ============= =================
951 NVRAM Address 951 NVRAM Address
952 ============= ================= 952 ============= =================
953 0x000-0x0ff not used 953 0x000-0x0ff not used
954 0x100-0x26f initialised data 954 0x100-0x26f initialised data
955 0x270-0x7ff not used 955 0x270-0x7ff not used
956 ============= ================= 956 ============= =================
957 957
958 general layout:: 958 general layout::
959 959
960 header - 6 bytes, 960 header - 6 bytes,
961 data - 356 bytes (checksum is byte 961 data - 356 bytes (checksum is byte sum of this data)
962 trailer - 6 bytes 962 trailer - 6 bytes
963 --- 963 ---
964 total 368 bytes 964 total 368 bytes
965 965
966 data area layout:: 966 data area layout::
967 967
968 controller set up - 20 bytes 968 controller set up - 20 bytes
969 boot configuration - 56 bytes (4x14 b 969 boot configuration - 56 bytes (4x14 bytes)
970 device set up - 128 bytes (16x8 b 970 device set up - 128 bytes (16x8 bytes)
971 unused (spare?) - 152 bytes (19x8 b 971 unused (spare?) - 152 bytes (19x8 bytes)
972 --- 972 ---
973 total 356 bytes 973 total 356 bytes
974 974
975 header:: 975 header::
976 976
977 00 00 - ?? start marker 977 00 00 - ?? start marker
978 64 01 - byte count (lsb/msb excludes hea 978 64 01 - byte count (lsb/msb excludes header/trailer)
979 8e 0b - checksum (lsb/msb excludes heade 979 8e 0b - checksum (lsb/msb excludes header/trailer)
980 980
981 controller set up:: 981 controller set up::
982 982
983 00 30 00 00 00 00 07 00 00 00 00 00 00 00 983 00 30 00 00 00 00 07 00 00 00 00 00 00 00 07 04 10 04 00 00
984 | | | | 984 | | | |
985 | | | - 985 | | | -- host ID
986 | | | 986 | | |
987 | | --Remov 987 | | --Removable Media Support
988 | | 0x00 988 | | 0x00 = none
989 | | 0x01 989 | | 0x01 = Bootable Device
990 | | 0x02 990 | | 0x02 = All with Media
991 | | 991 | |
992 | --flag bits 2 992 | --flag bits 2
993 | 0x00000001= scan 993 | 0x00000001= scan order hi->low
994 | (default 0x00 994 | (default 0x00 - scan low->hi)
995 --flag bits 1 995 --flag bits 1
996 0x00000001 scam enable 996 0x00000001 scam enable
997 0x00000010 parity enab 997 0x00000010 parity enable
998 0x00000100 verbose boo 998 0x00000100 verbose boot msgs
999 999
1000 remaining bytes unknown - they do not appear 1000 remaining bytes unknown - they do not appear to change in my
1001 current set up for any of the controllers. 1001 current set up for any of the controllers.
1002 1002
1003 default set up is identical for 53c810a and 5 1003 default set up is identical for 53c810a and 53c875 NVRAM
1004 (Removable Media added Symbios BIOS version 4 1004 (Removable Media added Symbios BIOS version 4.09)
1005 1005
1006 boot configuration 1006 boot configuration
1007 1007
1008 boot order set by order of the devices in thi 1008 boot order set by order of the devices in this table::
1009 1009
1010 04 00 0f 00 00 10 00 50 00 00 01 00 00 62 1010 04 00 0f 00 00 10 00 50 00 00 01 00 00 62 -- 1st controller
1011 04 00 03 00 00 10 00 58 00 00 01 00 00 63 1011 04 00 03 00 00 10 00 58 00 00 01 00 00 63 2nd controller
1012 04 00 01 00 00 10 00 48 00 00 01 00 00 61 1012 04 00 01 00 00 10 00 48 00 00 01 00 00 61 3rd controller
1013 00 00 00 00 00 00 00 00 00 00 00 00 00 00 1013 00 00 00 00 00 00 00 00 00 00 00 00 00 00 4th controller
1014 | | | | | | | | 1014 | | | | | | | |
1015 | | | | | | ---- P 1015 | | | | | | ---- PCI io port adr
1016 | | | | | --0x01 init/ 1016 | | | | | --0x01 init/scan at boot time
1017 | | | | --PCI device/function 1017 | | | | --PCI device/function number (0xdddddfff)
1018 | | ----- ?? PCI vendor ID (lsb/ms 1018 | | ----- ?? PCI vendor ID (lsb/msb)
1019 ----PCI device ID (lsb/msb) 1019 ----PCI device ID (lsb/msb)
1020 1020
1021 ?? use of this data is a guess but seems reas 1021 ?? use of this data is a guess but seems reasonable
1022 1022
1023 remaining bytes unknown - they do not appear 1023 remaining bytes unknown - they do not appear to change in my
1024 current set up 1024 current set up
1025 1025
1026 default set up is identical for 53c810a and 5 1026 default set up is identical for 53c810a and 53c875 NVRAM
1027 1027
1028 device set up (up to 16 devices - includes co 1028 device set up (up to 16 devices - includes controller)::
1029 1029
1030 0f 00 08 08 64 00 0a 00 - id 0 1030 0f 00 08 08 64 00 0a 00 - id 0
1031 0f 00 08 08 64 00 0a 00 1031 0f 00 08 08 64 00 0a 00
1032 0f 00 08 08 64 00 0a 00 1032 0f 00 08 08 64 00 0a 00
1033 0f 00 08 08 64 00 0a 00 1033 0f 00 08 08 64 00 0a 00
1034 0f 00 08 08 64 00 0a 00 1034 0f 00 08 08 64 00 0a 00
1035 0f 00 08 08 64 00 0a 00 1035 0f 00 08 08 64 00 0a 00
1036 0f 00 08 08 64 00 0a 00 1036 0f 00 08 08 64 00 0a 00
1037 0f 00 08 08 64 00 0a 00 1037 0f 00 08 08 64 00 0a 00
1038 1038
1039 0f 00 08 08 64 00 0a 00 1039 0f 00 08 08 64 00 0a 00
1040 0f 00 08 08 64 00 0a 00 1040 0f 00 08 08 64 00 0a 00
1041 0f 00 08 08 64 00 0a 00 1041 0f 00 08 08 64 00 0a 00
1042 0f 00 08 08 64 00 0a 00 1042 0f 00 08 08 64 00 0a 00
1043 0f 00 08 08 64 00 0a 00 1043 0f 00 08 08 64 00 0a 00
1044 0f 00 08 08 64 00 0a 00 1044 0f 00 08 08 64 00 0a 00
1045 0f 00 08 08 64 00 0a 00 1045 0f 00 08 08 64 00 0a 00
1046 0f 00 08 08 64 00 0a 00 - id 15 1046 0f 00 08 08 64 00 0a 00 - id 15
1047 | | | | | | 1047 | | | | | |
1048 | | | | ----timeout (lsb/msb) 1048 | | | | ----timeout (lsb/msb)
1049 | | | --synch period (0x?? 40 Mtra 1049 | | | --synch period (0x?? 40 Mtrans/sec- fast 40) (probably 0x28)
1050 | | | (0x30 20 Mtra 1050 | | | (0x30 20 Mtrans/sec- fast 20)
1051 | | | (0x64 10 Mtra 1051 | | | (0x64 10 Mtrans/sec- fast )
1052 | | | (0xc8 5 Mtra 1052 | | | (0xc8 5 Mtrans/sec)
1053 | | | (0x00 asynch 1053 | | | (0x00 asynchronous)
1054 | | -- ?? max sync offset (0x08 in 1054 | | -- ?? max sync offset (0x08 in NVRAM on 53c810a)
1055 | | (0x10 in 1055 | | (0x10 in NVRAM on 53c875)
1056 | --device bus width (0x08 narrow) 1056 | --device bus width (0x08 narrow)
1057 | (0x10 16 bit wi 1057 | (0x10 16 bit wide)
1058 --flag bits 1058 --flag bits
1059 0x00000001 - disconnect enabled 1059 0x00000001 - disconnect enabled
1060 0x00000010 - scan at boot time 1060 0x00000010 - scan at boot time
1061 0x00000100 - scan luns 1061 0x00000100 - scan luns
1062 0x00001000 - queue tags enabled 1062 0x00001000 - queue tags enabled
1063 1063
1064 remaining bytes unknown - they do not appear 1064 remaining bytes unknown - they do not appear to change in my
1065 current set up 1065 current set up
1066 1066
1067 ?? use of this data is a guess but seems reas 1067 ?? use of this data is a guess but seems reasonable
1068 (but it could be max bus width) 1068 (but it could be max bus width)
1069 1069
1070 default set up for 53c810a NVRAM 1070 default set up for 53c810a NVRAM
1071 default set up for 53c875 NVRAM 1071 default set up for 53c875 NVRAM
1072 1072
1073 - bus width 1073 - bus width - 0x10
1074 - sync offset 1074 - sync offset ? - 0x10
1075 - sync period 1075 - sync period - 0x30
1076 1076
1077 ?? spare device space (32 bit bus ??):: 1077 ?? spare device space (32 bit bus ??)::
1078 1078
1079 00 00 00 00 00 00 00 00 (19x8bytes) 1079 00 00 00 00 00 00 00 00 (19x8bytes)
1080 . 1080 .
1081 . 1081 .
1082 00 00 00 00 00 00 00 00 1082 00 00 00 00 00 00 00 00
1083 1083
1084 default set up is identical for 53c810a and 5 1084 default set up is identical for 53c810a and 53c875 NVRAM
1085 1085
1086 trailer:: 1086 trailer::
1087 1087
1088 fe fe - ? end marker ? 1088 fe fe - ? end marker ?
1089 00 00 1089 00 00
1090 00 00 1090 00 00
1091 1091
1092 default set up is identical for 53c810a and 5 1092 default set up is identical for 53c810a and 53c875 NVRAM
1093 1093
1094 17.3 Tekram NVRAM layout 1094 17.3 Tekram NVRAM layout
1095 ------------------------ 1095 ------------------------
1096 1096
1097 nvram 64x16 (1024 bit) 1097 nvram 64x16 (1024 bit)
1098 1098
1099 Drive settings:: 1099 Drive settings::
1100 1100
1101 Drive ID 0-15 (addr 0x0yyyy0 = device set 1101 Drive ID 0-15 (addr 0x0yyyy0 = device setup, yyyy = ID)
1102 (addr 0x0yyyy1 = 0x0000) 1102 (addr 0x0yyyy1 = 0x0000)
1103 1103
1104 x x x x x x x x x x x x x x x x 1104 x x x x x x x x x x x x x x x x
1105 | | | | | | | | | 1105 | | | | | | | | |
1106 | | | | | | | | ----- 1106 | | | | | | | | ----- parity check 0 - off
1107 | | | | | | | | 1107 | | | | | | | | 1 - on
1108 | | | | | | | | 1108 | | | | | | | |
1109 | | | | | | | ------- 1109 | | | | | | | ------- sync neg 0 - off
1110 | | | | | | | 1110 | | | | | | | 1 - on
1111 | | | | | | | 1111 | | | | | | |
1112 | | | | | | --------- 1112 | | | | | | --------- disconnect 0 - off
1113 | | | | | | 1113 | | | | | | 1 - on
1114 | | | | | | 1114 | | | | | |
1115 | | | | | ----------- 1115 | | | | | ----------- start cmd 0 - off
1116 | | | | | 1116 | | | | | 1 - on
1117 | | | | | 1117 | | | | |
1118 | | | | -------------- 1118 | | | | -------------- tagged cmds 0 - off
1119 | | | | 1119 | | | | 1 - on
1120 | | | | 1120 | | | |
1121 | | | ---------------- 1121 | | | ---------------- wide neg 0 - off
1122 | | | 1122 | | | 1 - on
1123 | | | 1123 | | |
1124 ------------------------- 1124 --------------------------- sync rate 0 - 10.0 Mtrans/sec
1125 1125 1 - 8.0
1126 1126 2 - 6.6
1127 1127 3 - 5.7
1128 1128 4 - 5.0
1129 1129 5 - 4.0
1130 1130 6 - 3.0
1131 1131 7 - 2.0
1132 1132 7 - 2.0
1133 1133 8 - 20.0
1134 1134 9 - 16.7
1135 1135 a - 13.9
1136 1136 b - 11.9
1137 1137
1138 Global settings 1138 Global settings
1139 1139
1140 Host flags 0 (addr 0x100000, 32):: 1140 Host flags 0 (addr 0x100000, 32)::
1141 1141
1142 x x x x x x x x x x x x x x x x 1142 x x x x x x x x x x x x x x x x
1143 | | | | | | | | | | | | 1143 | | | | | | | | | | | |
1144 | | | | | | | | ----------- h 1144 | | | | | | | | ----------- host ID 0x00 - 0x0f
1145 | | | | | | | | 1145 | | | | | | | |
1146 | | | | | | | ----------------------- s 1146 | | | | | | | ----------------------- support for 0 - off
1147 | | | | | | | > 1147 | | | | | | | > 2 drives 1 - on
1148 | | | | | | | 1148 | | | | | | |
1149 | | | | | | ------------------------- s 1149 | | | | | | ------------------------- support drives 0 - off
1150 | | | | | | > 1150 | | | | | | > 1Gbytes 1 - on
1151 | | | | | | 1151 | | | | | |
1152 | | | | | --------------------------- b 1152 | | | | | --------------------------- bus reset on 0 - off
1153 | | | | | 1153 | | | | | power on 1 - on
1154 | | | | | 1154 | | | | |
1155 | | | | ----------------------------- a 1155 | | | | ----------------------------- active neg 0 - off
1156 | | | | 1156 | | | | 1 - on
1157 | | | | 1157 | | | |
1158 | | | -------------------------------- i 1158 | | | -------------------------------- imm seek 0 - off
1159 | | | 1159 | | | 1 - on
1160 | | | 1160 | | |
1161 | | ---------------------------------- s 1161 | | ---------------------------------- scan luns 0 - off
1162 | | 1162 | | 1 - on
1163 | | 1163 | |
1164 -------------------------------------- r 1164 -------------------------------------- removable 0 - disable
1165 a 1165 as BIOS dev 1 - boot device
1166 1166 2 - all
1167 1167
1168 Host flags 1 (addr 0x100001, 33):: 1168 Host flags 1 (addr 0x100001, 33)::
1169 1169
1170 x x x x x x x x x x x x x x x x 1170 x x x x x x x x x x x x x x x x
1171 | | | | | | 1171 | | | | | |
1172 | | | --------- b 1172 | | | --------- boot delay 0 - 3 sec
1173 | | | 1173 | | | 1 - 5
1174 | | | 1174 | | | 2 - 10
1175 | | | 1175 | | | 3 - 20
1176 | | | 1176 | | | 4 - 30
1177 | | | 1177 | | | 5 - 60
1178 | | | 1178 | | | 6 - 120
1179 | | | 1179 | | |
1180 --------------------------- m 1180 --------------------------- max tag cmds 0 - 2
1181 1181 1 - 4
1182 1182 2 - 8
1183 1183 3 - 16
1184 1184 4 - 32
1185 1185
1186 Host flags 2 (addr 0x100010, 34):: 1186 Host flags 2 (addr 0x100010, 34)::
1187 1187
1188 x x x x x x x x x x x x x x x x 1188 x x x x x x x x x x x x x x x x
1189 | 1189 |
1190 ----- F 1190 ----- F2/F6 enable 0 - off ???
1191 1191 1 - on ???
1192 1192
1193 checksum (addr 0x111111) 1193 checksum (addr 0x111111)
1194 1194
1195 checksum = 0x1234 - (sum addr 0-63) 1195 checksum = 0x1234 - (sum addr 0-63)
1196 1196
1197 --------------------------------------------- 1197 ----------------------------------------------------------------------------
1198 1198
1199 default nvram data:: 1199 default nvram data::
1200 1200
1201 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 1201 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
1202 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 1202 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
1203 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 1203 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
1204 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 1204 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000 0x0037 0x0000
1205 1205
1206 0x0f07 0x0400 0x0001 0x0000 0x0000 0x0000 1206 0x0f07 0x0400 0x0001 0x0000 0x0000 0x0000 0x0000 0x0000
1207 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 1207 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
1208 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 1208 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000
1209 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 1209 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0x0000 0xfbbc
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.