1 ============================================== 1 ================================================
2 Imagination Technologies SPDIF Input Controlle 2 Imagination Technologies SPDIF Input Controllers
3 ============================================== 3 ================================================
4 4
5 The Imagination Technologies SPDIF Input contr 5 The Imagination Technologies SPDIF Input controller contains the following
6 controls: 6 controls:
7 7
8 * name='IEC958 Capture Mask',index=0 8 * name='IEC958 Capture Mask',index=0
9 9
10 This control returns a mask that shows which o 10 This control returns a mask that shows which of the IEC958 status bits
11 can be read using the 'IEC958 Capture Default' 11 can be read using the 'IEC958 Capture Default' control.
12 12
13 * name='IEC958 Capture Default',index=0 13 * name='IEC958 Capture Default',index=0
14 14
15 This control returns the status bits contained 15 This control returns the status bits contained within the SPDIF stream that
16 is being received. The 'IEC958 Capture Mask' s 16 is being received. The 'IEC958 Capture Mask' shows which bits can be read
17 from this control. 17 from this control.
18 18
19 * name='SPDIF In Multi Frequency Acquire',inde 19 * name='SPDIF In Multi Frequency Acquire',index=0
20 * name='SPDIF In Multi Frequency Acquire',inde 20 * name='SPDIF In Multi Frequency Acquire',index=1
21 * name='SPDIF In Multi Frequency Acquire',inde 21 * name='SPDIF In Multi Frequency Acquire',index=2
22 * name='SPDIF In Multi Frequency Acquire',inde 22 * name='SPDIF In Multi Frequency Acquire',index=3
23 23
24 This control is used to attempt acquisition of 24 This control is used to attempt acquisition of up to four different sample
25 rates. The active rate can be obtained by read 25 rates. The active rate can be obtained by reading the 'SPDIF In Lock Frequency'
26 control. 26 control.
27 27
28 When the value of this control is set to {0,0, 28 When the value of this control is set to {0,0,0,0}, the rate given to hw_params
29 will determine the single rate the block will 29 will determine the single rate the block will capture. Else, the rate given to
30 hw_params will be ignored, and the block will 30 hw_params will be ignored, and the block will attempt capture for each of the
31 four sample rates set here. 31 four sample rates set here.
32 32
33 If less than four rates are required, the same 33 If less than four rates are required, the same rate can be specified more than
34 once 34 once
35 35
36 * name='SPDIF In Lock Frequency',index=0 36 * name='SPDIF In Lock Frequency',index=0
37 37
38 This control returns the active capture rate, 38 This control returns the active capture rate, or 0 if a lock has not been
39 acquired 39 acquired
40 40
41 * name='SPDIF In Lock TRK',index=0 41 * name='SPDIF In Lock TRK',index=0
42 42
43 This control is used to modify the locking/jit 43 This control is used to modify the locking/jitter rejection characteristics
44 of the block. Larger values increase the locki 44 of the block. Larger values increase the locking range, but reduce jitter
45 rejection. 45 rejection.
46 46
47 * name='SPDIF In Lock Acquire Threshold',index 47 * name='SPDIF In Lock Acquire Threshold',index=0
48 48
49 This control is used to change the threshold a 49 This control is used to change the threshold at which a lock is acquired.
50 50
51 * name='SPDIF In Lock Release Threshold',index 51 * name='SPDIF In Lock Release Threshold',index=0
52 52
53 This control is used to change the threshold a 53 This control is used to change the threshold at which a lock is released.
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.