1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2 /*
3 * sc7280 CRD 3+ board device tree source
4 *
5 * Copyright 2022 Google LLC.
6 */
7
8 /dts-v1/;
9
10 #include "sc7280-herobrine.dtsi"
11 #include "sc7280-herobrine-audio-wcd9385.dtsi"
12 #include "sc7280-herobrine-lte-sku.dtsi"
13
14 / {
15 model = "Qualcomm Technologies, Inc. s
16 compatible = "google,zoglin", "google,
17
18 /* FIXED REGULATORS */
19
20 /*
21 * On most herobrine boards PPVAR_SYS
22 * However, on CRD there's an extra re
23 * is expected to be uncommon, we'll l
24 * in the baseboard herobrine.dtsi poi
25 * make a "_crd" specific version here
26 */
27 vreg_edp_bl_crd: vreg-edp-bl-crd-regul
28 compatible = "regulator-fixed"
29 regulator-name = "vreg_edp_bl_
30
31 gpio = <&pm8350c_gpios 6 GPIO_
32 enable-active-high;
33 pinctrl-names = "default";
34 pinctrl-0 = <&edp_bl_reg_en>;
35
36 vin-supply = <&ppvar_sys>;
37 };
38 };
39
40 /* ADDITIONS TO NODES DEFINED IN PARENT DEVICE
41
42 &apps_rsc {
43 regulators-2 {
44 compatible = "qcom,pmg1110-rpm
45 qcom,pmic-id = "k";
46
47 vreg_s1k_1p0: smps1 {
48 regulator-min-microvol
49 regulator-max-microvol
50 };
51 };
52 };
53
54 ap_tp_i2c: &i2c0 {
55 status = "okay";
56 clock-frequency = <400000>;
57
58 trackpad: trackpad@15 {
59 compatible = "hid-over-i2c";
60 reg = <0x15>;
61 pinctrl-names = "default";
62 pinctrl-0 = <&tp_int_odl>;
63
64 interrupt-parent = <&tlmm>;
65 interrupts = <7 IRQ_TYPE_EDGE_
66
67 post-power-on-delay-ms = <20>;
68 hid-descr-addr = <0x0001>;
69 vdd-supply = <&pp3300_z1>;
70
71 wakeup-source;
72 };
73 };
74
75 &ap_sar_sensor_i2c {
76 status = "okay";
77 };
78
79 &ap_sar_sensor0 {
80 status = "okay";
81 };
82
83 &ap_sar_sensor1 {
84 status = "okay";
85 };
86
87 ap_ts_pen_1v8: &i2c13 {
88 status = "okay";
89 clock-frequency = <400000>;
90
91 ap_ts: touchscreen@5c {
92 compatible = "hid-over-i2c";
93 reg = <0x5c>;
94 pinctrl-names = "default";
95 pinctrl-0 = <&ts_int_conn>, <&
96
97 interrupt-parent = <&tlmm>;
98 interrupts = <55 IRQ_TYPE_LEVE
99
100 post-power-on-delay-ms = <500>
101 hid-descr-addr = <0x0000>;
102
103 vdd-supply = <&pp3300_left_in_
104 };
105 };
106
107 &mdss_edp {
108 status = "okay";
109 };
110
111 &mdss_edp_phy {
112 status = "okay";
113 };
114
115 /* For nvme */
116 &pcie1 {
117 status = "okay";
118 };
119
120 /* For nvme */
121 &pcie1_phy {
122 status = "okay";
123 };
124
125 &pm8350c_pwm_backlight {
126 power-supply = <&vreg_edp_bl_crd>;
127 };
128
129 /* For eMMC */
130 &sdhc_1 {
131 status = "okay";
132 };
133
134 /* For SD Card */
135 &sdhc_2 {
136 status = "okay";
137 };
138
139 /* PINCTRL - ADDITIONS TO NODES IN PARENT DEVI
140
141 /*
142 * This pin goes to the display panel but then
143 * on the panel itself (it doesn't connect to
144 * We'll set a pullup here just to park the li
145 */
146 &ts_rst_conn {
147 bias-pull-up;
148 };
149
150 /* PINCTRL - BOARD-SPECIFIC */
151
152 /*
153 * Methodology for gpio-line-names:
154 * - If a pin goes to CRD board and is named i
155 * - If a pin goes to CRD board and is not nam
156 * - If a pin is totally internal to Qcard the
157 * - If a pin is not hooked up on Qcard, it ge
158 */
159
160 &pm8350c_gpios {
161 gpio-line-names = "FLASH_STROBE_1",
162 "AP_SUSPEND",
163 "PM8008_1_RST_N",
164 "",
165 "",
166 "EDP_BL_REG_EN",
167 "PMIC_EDP_BL_EN",
168 "PMIC_EDP_BL_PWM",
169 "";
170
171 edp_bl_reg_en: edp-bl-reg-en-state {
172 pins = "gpio6";
173 function = "normal";
174 bias-disable;
175 qcom,drive-strength = <PMIC_GP
176 };
177 };
178
179 &tlmm {
180 gpio-line-names = "AP_TP_I2C_SDA",
181 "AP_TP_I2C_SCL",
182 "PCIE1_RESET_N",
183 "PCIE1_WAKE_N",
184 "APPS_I2C_SDA",
185 "APPS_I2C_SCL",
186 "",
187 "TPAD_INT_N",
188 "",
189 "",
190
191 "GNSS_L1_EN",
192 "GNSS_L5_EN",
193 "QSPI_DATA_0",
194 "QSPI_DATA_1",
195 "QSPI_CLK",
196 "QSPI_CS_N_1",
197 /*
198 * AP_FLASH_WP is cr
199 * BIOS_FLASH_WP_L (
200 * signal is active
201 */
202 "AP_FLASH_WP",
203 "",
204 "AP_EC_INT_N",
205 "",
206
207 "CAM0_RST_N",
208 "CAM1_RST_N",
209 "SM_DBG_UART_TX",
210 "SM_DBG_UART_RX",
211 "",
212 "PM8008_IRQ_1",
213 "HOST2WLAN_SOL",
214 "WLAN2HOST_SOL",
215 "MOS_BT_UART_CTS",
216 "MOS_BT_UART_RFR",
217
218 "MOS_BT_UART_TX",
219 "MOS_BT_UART_RX",
220 "",
221 "HUB_RST",
222 "",
223 "",
224 "",
225 "",
226 "",
227 "",
228
229 "EC_SPI_MISO_GPIO40"
230 "EC_SPI_MOSI_GPIO41"
231 "EC_SPI_CLK_GPIO42",
232 "EC_SPI_CS_GPIO43",
233 "",
234 "EARLY_EUD_EN",
235 "",
236 "DP_HOT_PLUG_DETECT"
237 "AP_BRD_ID_0",
238 "AP_BRD_ID_1",
239
240 "AP_BRD_ID_2",
241 "NVME_PWR_REG_EN",
242 "TS_I2C_SDA_CONN",
243 "TS_I2C_CLK_CONN",
244 "TS_RST_CONN",
245 "TS_INT_CONN",
246 "AP_I2C_TPM_SDA",
247 "AP_I2C_TPM_SCL",
248 "",
249 "",
250
251 "EDP_HOT_PLUG_DET_N"
252 "",
253 "",
254 "AMP_EN",
255 "CAM0_MCLK_GPIO_64",
256 "CAM1_MCLK_GPIO_65",
257 "",
258 "",
259 "",
260 "CCI_I2C_SDA0",
261
262 "CCI_I2C_SCL0",
263 "",
264 "",
265 "",
266 "",
267 "",
268 "",
269 "",
270 "",
271 "PCIE1_CLK_REQ_N",
272
273 "EN_PP3300_DX_EDP",
274 "US_EURO_HS_SEL",
275 "FORCED_USB_BOOT",
276 "WCD_RESET_N",
277 "MOS_WLAN_EN",
278 "MOS_BT_EN",
279 "MOS_SW_CTRL",
280 "MOS_PCIE0_RST",
281 "MOS_PCIE0_CLKREQ_N"
282 "MOS_PCIE0_WAKE_N",
283
284 "MOS_LAA_AS_EN",
285 "SD_CARD_DET_CONN",
286 "",
287 "",
288 "MOS_BT_WLAN_SLIMBUS
289 "MOS_BT_WLAN_SLIMBUS
290 "",
291 "",
292 "",
293 "",
294
295 "",
296 "",
297 "",
298 "",
299 "H1_AP_INT_N",
300 "",
301 "AMP_BCLK",
302 "AMP_DIN",
303 "AMP_LRCLK",
304 "UIM1_DATA_GPIO_109"
305
306 "UIM1_CLK_GPIO_110",
307 "UIM1_RESET_GPIO_111
308 "",
309 "UIM1_DATA",
310 "UIM1_CLK",
311 "UIM1_RESET",
312 "UIM1_PRESENT",
313 "SDM_RFFE0_CLK",
314 "SDM_RFFE0_DATA",
315 "",
316
317 "SDM_RFFE1_DATA",
318 "SC_GPIO_121",
319 "FASTBOOT_SEL_1",
320 "SC_GPIO_123",
321 "FASTBOOT_SEL_2",
322 "SM_RFFE4_CLK_GRFC_8
323 "SM_RFFE4_DATA_GRFC_
324 "WLAN_COEX_UART1_RX"
325 "WLAN_COEX_UART1_TX"
326 "",
327
328 "",
329 "",
330 "",
331 "SDR_QLINK_REQ",
332 "SDR_QLINK_EN",
333 "QLINK0_WMSS_RESET_N
334 "SMR526_QLINK1_REQ",
335 "SMR526_QLINK1_EN",
336 "SMR526_QLINK1_WMSS_
337 "",
338
339 "SAR1_INT_N",
340 "SAR0_INT_N",
341 "",
342 "",
343 "WCD_SWR_TX_CLK",
344 "WCD_SWR_TX_DATA0",
345 "WCD_SWR_TX_DATA1",
346 "WCD_SWR_RX_CLK",
347 "WCD_SWR_RX_DATA0",
348 "WCD_SWR_RX_DATA1",
349
350 "DMIC01_CLK",
351 "DMIC01_DATA",
352 "DMIC23_CLK",
353 "DMIC23_DATA",
354 "",
355 "",
356 "EC_IN_RW_N",
357 "EN_PP3300_HUB",
358 "WCD_SWR_TX_DATA2",
359 "",
360
361 "",
362 "",
363 "",
364 "",
365 "",
366 "",
367 "",
368 "",
369 "",
370 "",
371
372 "",
373 "MOS_BLE_UART_TX",
374 "MOS_BLE_UART_RX",
375 "",
376 "";
377 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.