1 # SPDX-License-Identifier: GPL-2.0-only !! 1 # SPDX-License-Identifier: GPL-2.0
2 config MICROBLAZE !! 2 config MIPS
3 def_bool y !! 3 bool
4 select ARCH_32BIT_OFF_T !! 4 default y
5 select ARCH_NO_SWAP !! 5 select ARCH_32BIT_OFF_T if !64BIT
6 select ARCH_HAS_DMA_PREP_COHERENT !! 6 select ARCH_BINFMT_ELF_STATE if MIPS_FP_SUPPORT
7 select ARCH_HAS_GCOV_PROFILE_ALL !! 7 select ARCH_HAS_FORTIFY_SOURCE
8 select ARCH_HAS_SYNC_DMA_FOR_CPU !! 8 select ARCH_HAS_KCOV
9 select ARCH_HAS_SYNC_DMA_FOR_DEVICE !! 9 select ARCH_HAS_PTE_SPECIAL if !(32BIT && CPU_HAS_RIXI)
10 select ARCH_MIGHT_HAVE_PC_PARPORT !! 10 select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
>> 11 select ARCH_HAS_UBSAN_SANITIZE_ALL
>> 12 select ARCH_SUPPORTS_UPROBES
>> 13 select ARCH_USE_BUILTIN_BSWAP
>> 14 select ARCH_USE_CMPXCHG_LOCKREF if 64BIT
>> 15 select ARCH_USE_QUEUED_RWLOCKS
>> 16 select ARCH_USE_QUEUED_SPINLOCKS
>> 17 select ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT if MMU
11 select ARCH_WANT_IPC_PARSE_VERSION 18 select ARCH_WANT_IPC_PARSE_VERSION
12 select BUILDTIME_TABLE_SORT 19 select BUILDTIME_TABLE_SORT
13 select TIMER_OF !! 20 select CLONE_BACKWARDS
14 select CLONE_BACKWARDS3 !! 21 select CPU_NO_EFFICIENT_FFS if (TARGET_ISA_REV < 1)
15 select COMMON_CLK !! 22 select CPU_PM if CPU_IDLE
16 select DMA_DIRECT_REMAP !! 23 select GENERIC_ATOMIC64 if !64BIT
17 select GENERIC_ATOMIC64 !! 24 select GENERIC_CLOCKEVENTS
18 select GENERIC_CPU_DEVICES !! 25 select GENERIC_CMOS_UPDATE
19 select GENERIC_IDLE_POLL_SETUP !! 26 select GENERIC_CPU_AUTOPROBE
>> 27 select GENERIC_GETTIMEOFDAY
>> 28 select GENERIC_IOMAP
20 select GENERIC_IRQ_PROBE 29 select GENERIC_IRQ_PROBE
21 select GENERIC_IRQ_SHOW 30 select GENERIC_IRQ_SHOW
22 select GENERIC_PCI_IOMAP !! 31 select GENERIC_ISA_DMA if EISA
23 select GENERIC_SCHED_CLOCK !! 32 select GENERIC_LIB_ASHLDI3
24 select HAS_IOPORT if PCI !! 33 select GENERIC_LIB_ASHRDI3
25 select HAVE_ARCH_HASH !! 34 select GENERIC_LIB_CMPDI2
>> 35 select GENERIC_LIB_LSHRDI3
>> 36 select GENERIC_LIB_UCMPDI2
>> 37 select GENERIC_SCHED_CLOCK if !CAVIUM_OCTEON_SOC
>> 38 select GENERIC_SMP_IDLE_THREAD
>> 39 select GENERIC_TIME_VSYSCALL
>> 40 select GUP_GET_PTE_LOW_HIGH if CPU_MIPS32 && PHYS_ADDR_T_64BIT
>> 41 select HANDLE_DOMAIN_IRQ
>> 42 select HAVE_ARCH_COMPILER_H
>> 43 select HAVE_ARCH_JUMP_LABEL
26 select HAVE_ARCH_KGDB 44 select HAVE_ARCH_KGDB
27 select HAVE_ARCH_SECCOMP !! 45 select HAVE_ARCH_MMAP_RND_BITS if MMU
>> 46 select HAVE_ARCH_MMAP_RND_COMPAT_BITS if MMU && COMPAT
>> 47 select HAVE_ARCH_SECCOMP_FILTER
>> 48 select HAVE_ARCH_TRACEHOOK
>> 49 select HAVE_ARCH_TRANSPARENT_HUGEPAGE if CPU_SUPPORTS_HUGEPAGES
>> 50 select HAVE_ASM_MODVERSIONS
>> 51 select HAVE_CBPF_JIT if !64BIT && !CPU_MICROMIPS
>> 52 select HAVE_CONTEXT_TRACKING
>> 53 select HAVE_TIF_NOHZ
>> 54 select HAVE_COPY_THREAD_TLS
>> 55 select HAVE_C_RECORDMCOUNT
28 select HAVE_DEBUG_KMEMLEAK 56 select HAVE_DEBUG_KMEMLEAK
>> 57 select HAVE_DEBUG_STACKOVERFLOW
29 select HAVE_DMA_CONTIGUOUS 58 select HAVE_DMA_CONTIGUOUS
30 select HAVE_DYNAMIC_FTRACE 59 select HAVE_DYNAMIC_FTRACE
>> 60 select HAVE_EBPF_JIT if 64BIT && !CPU_MICROMIPS && TARGET_ISA_REV >= 2
>> 61 select HAVE_EXIT_THREAD
>> 62 select HAVE_FAST_GUP
31 select HAVE_FTRACE_MCOUNT_RECORD 63 select HAVE_FTRACE_MCOUNT_RECORD
32 select HAVE_FUNCTION_GRAPH_TRACER 64 select HAVE_FUNCTION_GRAPH_TRACER
33 select HAVE_FUNCTION_TRACER 65 select HAVE_FUNCTION_TRACER
34 select HAVE_PAGE_SIZE_4KB !! 66 select HAVE_GCC_PLUGINS
>> 67 select HAVE_GENERIC_VDSO
>> 68 select HAVE_IDE
>> 69 select HAVE_IOREMAP_PROT
>> 70 select HAVE_IRQ_EXIT_ON_IRQ_STACK
>> 71 select HAVE_IRQ_TIME_ACCOUNTING
>> 72 select HAVE_KPROBES
>> 73 select HAVE_KRETPROBES
>> 74 select HAVE_LD_DEAD_CODE_DATA_ELIMINATION
>> 75 select HAVE_MEMBLOCK_NODE_MAP
>> 76 select HAVE_MOD_ARCH_SPECIFIC
>> 77 select HAVE_NMI
>> 78 select HAVE_OPROFILE
>> 79 select HAVE_PERF_EVENTS
>> 80 select HAVE_REGS_AND_STACK_ACCESS_API
>> 81 select HAVE_RSEQ
>> 82 select HAVE_SPARSE_SYSCALL_NR
>> 83 select HAVE_STACKPROTECTOR
>> 84 select HAVE_SYSCALL_TRACEPOINTS
>> 85 select HAVE_VIRT_CPU_ACCOUNTING_GEN if 64BIT || !SMP
>> 86 select IRQ_FORCED_THREADING
>> 87 select ISA if EISA
>> 88 select MODULES_USE_ELF_REL if MODULES
>> 89 select MODULES_USE_ELF_RELA if MODULES && 64BIT
>> 90 select PERF_USE_VMALLOC
>> 91 select RTC_LIB
>> 92 select SYSCTL_EXCEPTION_TRACE
>> 93 select VIRT_TO_BUS
>> 94
>> 95 menu "Machine selection"
>> 96
>> 97 choice
>> 98 prompt "System type"
>> 99 default MIPS_GENERIC
>> 100
>> 101 config MIPS_GENERIC
>> 102 bool "Generic board-agnostic MIPS kernel"
>> 103 select BOOT_RAW
>> 104 select BUILTIN_DTB
>> 105 select CEVT_R4K
>> 106 select CLKSRC_MIPS_GIC
>> 107 select COMMON_CLK
>> 108 select CPU_MIPSR2_IRQ_EI
>> 109 select CPU_MIPSR2_IRQ_VI
>> 110 select CSRC_R4K
>> 111 select DMA_PERDEV_COHERENT
35 select HAVE_PCI 112 select HAVE_PCI
>> 113 select IRQ_MIPS_CPU
>> 114 select MIPS_AUTO_PFN_OFFSET
>> 115 select MIPS_CPU_SCACHE
>> 116 select MIPS_GIC
>> 117 select MIPS_L1_CACHE_SHIFT_7
>> 118 select NO_EXCEPT_FILL
>> 119 select PCI_DRIVERS_GENERIC
>> 120 select SMP_UP if SMP
>> 121 select SWAP_IO_SPACE
>> 122 select SYS_HAS_CPU_MIPS32_R1
>> 123 select SYS_HAS_CPU_MIPS32_R2
>> 124 select SYS_HAS_CPU_MIPS32_R6
>> 125 select SYS_HAS_CPU_MIPS64_R1
>> 126 select SYS_HAS_CPU_MIPS64_R2
>> 127 select SYS_HAS_CPU_MIPS64_R6
>> 128 select SYS_SUPPORTS_32BIT_KERNEL
>> 129 select SYS_SUPPORTS_64BIT_KERNEL
>> 130 select SYS_SUPPORTS_BIG_ENDIAN
>> 131 select SYS_SUPPORTS_HIGHMEM
>> 132 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 133 select SYS_SUPPORTS_MICROMIPS
>> 134 select SYS_SUPPORTS_MIPS16
>> 135 select SYS_SUPPORTS_MIPS_CPS
>> 136 select SYS_SUPPORTS_MULTITHREADING
>> 137 select SYS_SUPPORTS_RELOCATABLE
>> 138 select SYS_SUPPORTS_SMARTMIPS
>> 139 select UHI_BOOT
>> 140 select USB_EHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
>> 141 select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
>> 142 select USB_OHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
>> 143 select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
>> 144 select USB_UHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
>> 145 select USB_UHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
>> 146 select USE_OF
>> 147 help
>> 148 Select this to build a kernel which aims to support multiple boards,
>> 149 generally using a flattened device tree passed from the bootloader
>> 150 using the boot protocol defined in the UHI (Unified Hosting
>> 151 Interface) specification.
>> 152
>> 153 config MIPS_ALCHEMY
>> 154 bool "Alchemy processor based machines"
>> 155 select PHYS_ADDR_T_64BIT
>> 156 select CEVT_R4K
>> 157 select CSRC_R4K
>> 158 select IRQ_MIPS_CPU
>> 159 select DMA_MAYBE_COHERENT # Au1000,1500,1100 aren't, rest is
>> 160 select SYS_HAS_CPU_MIPS32_R1
>> 161 select SYS_SUPPORTS_32BIT_KERNEL
>> 162 select SYS_SUPPORTS_APM_EMULATION
>> 163 select GPIOLIB
>> 164 select SYS_SUPPORTS_ZBOOT
>> 165 select COMMON_CLK
>> 166
>> 167 config AR7
>> 168 bool "Texas Instruments AR7"
>> 169 select BOOT_ELF32
>> 170 select DMA_NONCOHERENT
>> 171 select CEVT_R4K
>> 172 select CSRC_R4K
>> 173 select IRQ_MIPS_CPU
>> 174 select NO_EXCEPT_FILL
>> 175 select SWAP_IO_SPACE
>> 176 select SYS_HAS_CPU_MIPS32_R1
>> 177 select SYS_HAS_EARLY_PRINTK
>> 178 select SYS_SUPPORTS_32BIT_KERNEL
>> 179 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 180 select SYS_SUPPORTS_MIPS16
>> 181 select SYS_SUPPORTS_ZBOOT_UART16550
>> 182 select GPIOLIB
>> 183 select VLYNQ
>> 184 select HAVE_CLK
>> 185 help
>> 186 Support for the Texas Instruments AR7 System-on-a-Chip
>> 187 family: TNETD7100, 7200 and 7300.
>> 188
>> 189 config ATH25
>> 190 bool "Atheros AR231x/AR531x SoC support"
>> 191 select CEVT_R4K
>> 192 select CSRC_R4K
>> 193 select DMA_NONCOHERENT
>> 194 select IRQ_MIPS_CPU
36 select IRQ_DOMAIN 195 select IRQ_DOMAIN
37 select XILINX_INTC !! 196 select SYS_HAS_CPU_MIPS32_R1
38 select MODULES_USE_ELF_RELA !! 197 select SYS_SUPPORTS_BIG_ENDIAN
39 select OF !! 198 select SYS_SUPPORTS_32BIT_KERNEL
40 select OF_EARLY_FLATTREE !! 199 select SYS_HAS_EARLY_PRINTK
41 select PCI_DOMAINS_GENERIC if PCI !! 200 help
42 select PCI_SYSCALL if PCI !! 201 Support for Atheros AR231x and Atheros AR531x based boards
43 select CPU_NO_EFFICIENT_FFS !! 202
44 select MMU_GATHER_NO_RANGE !! 203 config ATH79
45 select SPARSE_IRQ !! 204 bool "Atheros AR71XX/AR724X/AR913X based boards"
46 select ZONE_DMA !! 205 select ARCH_HAS_RESET_CONTROLLER
47 select TRACE_IRQFLAGS_SUPPORT !! 206 select BOOT_RAW
48 select GENERIC_IRQ_MULTI_HANDLER !! 207 select CEVT_R4K
>> 208 select CSRC_R4K
>> 209 select DMA_NONCOHERENT
>> 210 select GPIOLIB
>> 211 select PINCTRL
>> 212 select HAVE_CLK
>> 213 select COMMON_CLK
>> 214 select CLKDEV_LOOKUP
>> 215 select IRQ_MIPS_CPU
>> 216 select SYS_HAS_CPU_MIPS32_R2
>> 217 select SYS_HAS_EARLY_PRINTK
>> 218 select SYS_SUPPORTS_32BIT_KERNEL
>> 219 select SYS_SUPPORTS_BIG_ENDIAN
>> 220 select SYS_SUPPORTS_MIPS16
>> 221 select SYS_SUPPORTS_ZBOOT_UART_PROM
>> 222 select USE_OF
>> 223 select USB_EHCI_ROOT_HUB_TT if USB_EHCI_HCD_PLATFORM
>> 224 help
>> 225 Support for the Atheros AR71XX/AR724X/AR913X SoCs.
>> 226
>> 227 config BMIPS_GENERIC
>> 228 bool "Broadcom Generic BMIPS kernel"
>> 229 select ARCH_HAS_SYNC_DMA_FOR_CPU_ALL
>> 230 select ARCH_HAS_PHYS_TO_DMA
>> 231 select BOOT_RAW
>> 232 select NO_EXCEPT_FILL
>> 233 select USE_OF
>> 234 select CEVT_R4K
>> 235 select CSRC_R4K
>> 236 select SYNC_R4K
>> 237 select COMMON_CLK
>> 238 select BCM6345_L1_IRQ
>> 239 select BCM7038_L1_IRQ
>> 240 select BCM7120_L2_IRQ
>> 241 select BRCMSTB_L2_IRQ
>> 242 select IRQ_MIPS_CPU
>> 243 select DMA_NONCOHERENT
>> 244 select SYS_SUPPORTS_32BIT_KERNEL
>> 245 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 246 select SYS_SUPPORTS_BIG_ENDIAN
>> 247 select SYS_SUPPORTS_HIGHMEM
>> 248 select SYS_HAS_CPU_BMIPS32_3300
>> 249 select SYS_HAS_CPU_BMIPS4350
>> 250 select SYS_HAS_CPU_BMIPS4380
>> 251 select SYS_HAS_CPU_BMIPS5000
>> 252 select SWAP_IO_SPACE
>> 253 select USB_EHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
>> 254 select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
>> 255 select USB_OHCI_BIG_ENDIAN_DESC if CPU_BIG_ENDIAN
>> 256 select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
>> 257 select HARDIRQS_SW_RESEND
>> 258 help
>> 259 Build a generic DT-based kernel image that boots on select
>> 260 BCM33xx cable modem chips, BCM63xx DSL chips, and BCM7xxx set-top
>> 261 box chips. Note that CONFIG_CPU_BIG_ENDIAN/CONFIG_CPU_LITTLE_ENDIAN
>> 262 must be set appropriately for your board.
>> 263
>> 264 config BCM47XX
>> 265 bool "Broadcom BCM47XX based boards"
>> 266 select BOOT_RAW
>> 267 select CEVT_R4K
>> 268 select CSRC_R4K
>> 269 select DMA_NONCOHERENT
>> 270 select HAVE_PCI
>> 271 select IRQ_MIPS_CPU
>> 272 select SYS_HAS_CPU_MIPS32_R1
>> 273 select NO_EXCEPT_FILL
>> 274 select SYS_SUPPORTS_32BIT_KERNEL
>> 275 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 276 select SYS_SUPPORTS_MIPS16
>> 277 select SYS_SUPPORTS_ZBOOT
>> 278 select SYS_HAS_EARLY_PRINTK
>> 279 select USE_GENERIC_EARLY_PRINTK_8250
>> 280 select GPIOLIB
>> 281 select LEDS_GPIO_REGISTER
>> 282 select BCM47XX_NVRAM
>> 283 select BCM47XX_SPROM
>> 284 select BCM47XX_SSB if !BCM47XX_BCMA
>> 285 help
>> 286 Support for BCM47XX based boards
>> 287
>> 288 config BCM63XX
>> 289 bool "Broadcom BCM63XX based boards"
>> 290 select BOOT_RAW
>> 291 select CEVT_R4K
>> 292 select CSRC_R4K
>> 293 select SYNC_R4K
>> 294 select DMA_NONCOHERENT
>> 295 select IRQ_MIPS_CPU
>> 296 select SYS_SUPPORTS_32BIT_KERNEL
>> 297 select SYS_SUPPORTS_BIG_ENDIAN
>> 298 select SYS_HAS_EARLY_PRINTK
>> 299 select SWAP_IO_SPACE
>> 300 select GPIOLIB
>> 301 select HAVE_CLK
>> 302 select MIPS_L1_CACHE_SHIFT_4
>> 303 select CLKDEV_LOOKUP
>> 304 help
>> 305 Support for BCM63XX based boards
>> 306
>> 307 config MIPS_COBALT
>> 308 bool "Cobalt Server"
>> 309 select CEVT_R4K
>> 310 select CSRC_R4K
>> 311 select CEVT_GT641XX
>> 312 select DMA_NONCOHERENT
>> 313 select FORCE_PCI
>> 314 select I8253
>> 315 select I8259
>> 316 select IRQ_MIPS_CPU
>> 317 select IRQ_GT641XX
>> 318 select PCI_GT64XXX_PCI0
>> 319 select SYS_HAS_CPU_NEVADA
>> 320 select SYS_HAS_EARLY_PRINTK
>> 321 select SYS_SUPPORTS_32BIT_KERNEL
>> 322 select SYS_SUPPORTS_64BIT_KERNEL
>> 323 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 324 select USE_GENERIC_EARLY_PRINTK_8250
>> 325
>> 326 config MACH_DECSTATION
>> 327 bool "DECstations"
>> 328 select BOOT_ELF32
>> 329 select CEVT_DS1287
>> 330 select CEVT_R4K if CPU_R4X00
>> 331 select CSRC_IOASIC
>> 332 select CSRC_R4K if CPU_R4X00
>> 333 select CPU_DADDI_WORKAROUNDS if 64BIT
>> 334 select CPU_R4000_WORKAROUNDS if 64BIT
>> 335 select CPU_R4400_WORKAROUNDS if 64BIT
>> 336 select DMA_NONCOHERENT
>> 337 select NO_IOPORT_MAP
>> 338 select IRQ_MIPS_CPU
>> 339 select SYS_HAS_CPU_R3000
>> 340 select SYS_HAS_CPU_R4X00
>> 341 select SYS_SUPPORTS_32BIT_KERNEL
>> 342 select SYS_SUPPORTS_64BIT_KERNEL
>> 343 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 344 select SYS_SUPPORTS_128HZ
>> 345 select SYS_SUPPORTS_256HZ
>> 346 select SYS_SUPPORTS_1024HZ
>> 347 select MIPS_L1_CACHE_SHIFT_4
>> 348 help
>> 349 This enables support for DEC's MIPS based workstations. For details
>> 350 see the Linux/MIPS FAQ on <http://www.linux-mips.org/> and the
>> 351 DECstation porting pages on <http://decstation.unix-ag.org/>.
>> 352
>> 353 If you have one of the following DECstation Models you definitely
>> 354 want to choose R4xx0 for the CPU Type:
>> 355
>> 356 DECstation 5000/50
>> 357 DECstation 5000/150
>> 358 DECstation 5000/260
>> 359 DECsystem 5900/260
>> 360
>> 361 otherwise choose R3000.
>> 362
>> 363 config MACH_JAZZ
>> 364 bool "Jazz family of machines"
>> 365 select ARC_MEMORY
>> 366 select ARC_PROMLIB
>> 367 select ARCH_MIGHT_HAVE_PC_PARPORT
>> 368 select ARCH_MIGHT_HAVE_PC_SERIO
>> 369 select FW_ARC
>> 370 select FW_ARC32
>> 371 select ARCH_MAY_HAVE_PC_FDC
>> 372 select CEVT_R4K
>> 373 select CSRC_R4K
>> 374 select DEFAULT_SGI_PARTITION if CPU_BIG_ENDIAN
>> 375 select GENERIC_ISA_DMA
>> 376 select HAVE_PCSPKR_PLATFORM
>> 377 select IRQ_MIPS_CPU
>> 378 select I8253
>> 379 select I8259
>> 380 select ISA
>> 381 select SYS_HAS_CPU_R4X00
>> 382 select SYS_SUPPORTS_32BIT_KERNEL
>> 383 select SYS_SUPPORTS_64BIT_KERNEL
>> 384 select SYS_SUPPORTS_100HZ
>> 385 help
>> 386 This a family of machines based on the MIPS R4030 chipset which was
>> 387 used by several vendors to build RISC/os and Windows NT workstations.
>> 388 Members include the Acer PICA, MIPS Magnum 4000, MIPS Millennium and
>> 389 Olivetti M700-10 workstations.
>> 390
>> 391 config MACH_INGENIC
>> 392 bool "Ingenic SoC based machines"
>> 393 select SYS_SUPPORTS_32BIT_KERNEL
>> 394 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 395 select SYS_SUPPORTS_ZBOOT_UART16550
>> 396 select CPU_SUPPORTS_HUGEPAGES
>> 397 select DMA_NONCOHERENT
>> 398 select IRQ_MIPS_CPU
>> 399 select PINCTRL
>> 400 select GPIOLIB
>> 401 select COMMON_CLK
>> 402 select GENERIC_IRQ_CHIP
>> 403 select BUILTIN_DTB if MIPS_NO_APPENDED_DTB
>> 404 select USE_OF
>> 405
>> 406 config LANTIQ
>> 407 bool "Lantiq based platforms"
>> 408 select DMA_NONCOHERENT
>> 409 select IRQ_MIPS_CPU
>> 410 select CEVT_R4K
>> 411 select CSRC_R4K
>> 412 select SYS_HAS_CPU_MIPS32_R1
>> 413 select SYS_HAS_CPU_MIPS32_R2
>> 414 select SYS_SUPPORTS_BIG_ENDIAN
>> 415 select SYS_SUPPORTS_32BIT_KERNEL
>> 416 select SYS_SUPPORTS_MIPS16
>> 417 select SYS_SUPPORTS_MULTITHREADING
>> 418 select SYS_SUPPORTS_VPE_LOADER
>> 419 select SYS_HAS_EARLY_PRINTK
>> 420 select GPIOLIB
>> 421 select SWAP_IO_SPACE
>> 422 select BOOT_RAW
>> 423 select CLKDEV_LOOKUP
>> 424 select USE_OF
>> 425 select PINCTRL
>> 426 select PINCTRL_LANTIQ
>> 427 select ARCH_HAS_RESET_CONTROLLER
>> 428 select RESET_CONTROLLER
>> 429
>> 430 config LASAT
>> 431 bool "LASAT Networks platforms"
>> 432 select CEVT_R4K
>> 433 select CRC32
>> 434 select CSRC_R4K
>> 435 select DMA_NONCOHERENT
>> 436 select SYS_HAS_EARLY_PRINTK
>> 437 select HAVE_PCI
>> 438 select IRQ_MIPS_CPU
>> 439 select PCI_GT64XXX_PCI0
>> 440 select MIPS_NILE4
>> 441 select R5000_CPU_SCACHE
>> 442 select SYS_HAS_CPU_R5000
>> 443 select SYS_SUPPORTS_32BIT_KERNEL
>> 444 select SYS_SUPPORTS_64BIT_KERNEL if BROKEN
>> 445 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 446
>> 447 config MACH_LOONGSON32
>> 448 bool "Loongson 32-bit family of machines"
>> 449 select SYS_SUPPORTS_ZBOOT
>> 450 help
>> 451 This enables support for the Loongson-1 family of machines.
>> 452
>> 453 Loongson-1 is a family of 32-bit MIPS-compatible SoCs developed by
>> 454 the Institute of Computing Technology (ICT), Chinese Academy of
>> 455 Sciences (CAS).
>> 456
>> 457 config MACH_LOONGSON2EF
>> 458 bool "Loongson-2E/F family of machines"
>> 459 select SYS_SUPPORTS_ZBOOT
>> 460 help
>> 461 This enables the support of early Loongson-2E/F family of machines.
>> 462
>> 463 config MACH_LOONGSON64
>> 464 bool "Loongson 64-bit family of machines"
>> 465 select ARCH_SPARSEMEM_ENABLE
>> 466 select ARCH_MIGHT_HAVE_PC_PARPORT
>> 467 select ARCH_MIGHT_HAVE_PC_SERIO
>> 468 select GENERIC_ISA_DMA_SUPPORT_BROKEN
>> 469 select BOOT_ELF32
>> 470 select BOARD_SCACHE
>> 471 select CSRC_R4K
>> 472 select CEVT_R4K
>> 473 select CPU_HAS_WB
>> 474 select FORCE_PCI
>> 475 select ISA
>> 476 select I8259
>> 477 select IRQ_MIPS_CPU
>> 478 select NR_CPUS_DEFAULT_4
>> 479 select USE_GENERIC_EARLY_PRINTK_8250
>> 480 select SYS_HAS_CPU_LOONGSON64
>> 481 select SYS_HAS_EARLY_PRINTK
>> 482 select SYS_SUPPORTS_SMP
>> 483 select SYS_SUPPORTS_HOTPLUG_CPU
>> 484 select SYS_SUPPORTS_NUMA
>> 485 select SYS_SUPPORTS_64BIT_KERNEL
>> 486 select SYS_SUPPORTS_HIGHMEM
>> 487 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 488 select SYS_SUPPORTS_ZBOOT
>> 489 select ZONE_DMA32
>> 490 select NUMA
>> 491 select COMMON_CLK
>> 492 select USE_OF
>> 493 select BUILTIN_DTB
>> 494 help
>> 495 This enables the support of Loongson-2/3 family of machines.
>> 496
>> 497 Loongson-2 and Loongson-3 are 64-bit general-purpose processors with
>> 498 GS264/GS464/GS464E/GS464V microarchitecture (except old Loongson-2E
>> 499 and Loongson-2F which will be removed), developed by the Institute
>> 500 of Computing Technology (ICT), Chinese Academy of Sciences (CAS).
>> 501
>> 502 config MACH_PISTACHIO
>> 503 bool "IMG Pistachio SoC based boards"
>> 504 select BOOT_ELF32
>> 505 select BOOT_RAW
>> 506 select CEVT_R4K
>> 507 select CLKSRC_MIPS_GIC
>> 508 select COMMON_CLK
>> 509 select CSRC_R4K
>> 510 select DMA_NONCOHERENT
>> 511 select GPIOLIB
>> 512 select IRQ_MIPS_CPU
>> 513 select MFD_SYSCON
>> 514 select MIPS_CPU_SCACHE
>> 515 select MIPS_GIC
>> 516 select PINCTRL
>> 517 select REGULATOR
>> 518 select SYS_HAS_CPU_MIPS32_R2
>> 519 select SYS_SUPPORTS_32BIT_KERNEL
>> 520 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 521 select SYS_SUPPORTS_MIPS_CPS
>> 522 select SYS_SUPPORTS_MULTITHREADING
>> 523 select SYS_SUPPORTS_RELOCATABLE
>> 524 select SYS_SUPPORTS_ZBOOT
>> 525 select SYS_HAS_EARLY_PRINTK
>> 526 select USE_GENERIC_EARLY_PRINTK_8250
>> 527 select USE_OF
>> 528 help
>> 529 This enables support for the IMG Pistachio SoC platform.
>> 530
>> 531 config MIPS_MALTA
>> 532 bool "MIPS Malta board"
>> 533 select ARCH_MAY_HAVE_PC_FDC
>> 534 select ARCH_MIGHT_HAVE_PC_PARPORT
>> 535 select ARCH_MIGHT_HAVE_PC_SERIO
>> 536 select BOOT_ELF32
>> 537 select BOOT_RAW
>> 538 select BUILTIN_DTB
>> 539 select CEVT_R4K
>> 540 select CLKSRC_MIPS_GIC
>> 541 select COMMON_CLK
>> 542 select CSRC_R4K
>> 543 select DMA_MAYBE_COHERENT
>> 544 select GENERIC_ISA_DMA
>> 545 select HAVE_PCSPKR_PLATFORM
>> 546 select HAVE_PCI
>> 547 select I8253
>> 548 select I8259
>> 549 select IRQ_MIPS_CPU
>> 550 select MIPS_BONITO64
>> 551 select MIPS_CPU_SCACHE
>> 552 select MIPS_GIC
>> 553 select MIPS_L1_CACHE_SHIFT_6
>> 554 select MIPS_MSC
>> 555 select PCI_GT64XXX_PCI0
>> 556 select SMP_UP if SMP
>> 557 select SWAP_IO_SPACE
>> 558 select SYS_HAS_CPU_MIPS32_R1
>> 559 select SYS_HAS_CPU_MIPS32_R2
>> 560 select SYS_HAS_CPU_MIPS32_R3_5
>> 561 select SYS_HAS_CPU_MIPS32_R5
>> 562 select SYS_HAS_CPU_MIPS32_R6
>> 563 select SYS_HAS_CPU_MIPS64_R1
>> 564 select SYS_HAS_CPU_MIPS64_R2
>> 565 select SYS_HAS_CPU_MIPS64_R6
>> 566 select SYS_HAS_CPU_NEVADA
>> 567 select SYS_HAS_CPU_RM7000
>> 568 select SYS_SUPPORTS_32BIT_KERNEL
>> 569 select SYS_SUPPORTS_64BIT_KERNEL
>> 570 select SYS_SUPPORTS_BIG_ENDIAN
>> 571 select SYS_SUPPORTS_HIGHMEM
>> 572 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 573 select SYS_SUPPORTS_MICROMIPS
>> 574 select SYS_SUPPORTS_MIPS16
>> 575 select SYS_SUPPORTS_MIPS_CMP
>> 576 select SYS_SUPPORTS_MIPS_CPS
>> 577 select SYS_SUPPORTS_MULTITHREADING
>> 578 select SYS_SUPPORTS_RELOCATABLE
>> 579 select SYS_SUPPORTS_SMARTMIPS
>> 580 select SYS_SUPPORTS_VPE_LOADER
>> 581 select SYS_SUPPORTS_ZBOOT
>> 582 select USE_OF
>> 583 select ZONE_DMA32 if 64BIT
>> 584 help
>> 585 This enables support for the MIPS Technologies Malta evaluation
>> 586 board.
>> 587
>> 588 config MACH_PIC32
>> 589 bool "Microchip PIC32 Family"
>> 590 help
>> 591 This enables support for the Microchip PIC32 family of platforms.
>> 592
>> 593 Microchip PIC32 is a family of general-purpose 32 bit MIPS core
>> 594 microcontrollers.
>> 595
>> 596 config NEC_MARKEINS
>> 597 bool "NEC EMMA2RH Mark-eins board"
>> 598 select SOC_EMMA2RH
>> 599 select HAVE_PCI
>> 600 help
>> 601 This enables support for the NEC Electronics Mark-eins boards.
>> 602
>> 603 config MACH_VR41XX
>> 604 bool "NEC VR4100 series based machines"
>> 605 select CEVT_R4K
>> 606 select CSRC_R4K
>> 607 select SYS_HAS_CPU_VR41XX
>> 608 select SYS_SUPPORTS_MIPS16
>> 609 select GPIOLIB
>> 610
>> 611 config NXP_STB220
>> 612 bool "NXP STB220 board"
>> 613 select SOC_PNX833X
>> 614 help
>> 615 Support for NXP Semiconductors STB220 Development Board.
>> 616
>> 617 config NXP_STB225
>> 618 bool "NXP 225 board"
>> 619 select SOC_PNX833X
>> 620 select SOC_PNX8335
>> 621 help
>> 622 Support for NXP Semiconductors STB225 Development Board.
>> 623
>> 624 config PMC_MSP
>> 625 bool "PMC-Sierra MSP chipsets"
>> 626 select CEVT_R4K
>> 627 select CSRC_R4K
>> 628 select DMA_NONCOHERENT
>> 629 select SWAP_IO_SPACE
>> 630 select NO_EXCEPT_FILL
>> 631 select BOOT_RAW
>> 632 select SYS_HAS_CPU_MIPS32_R1
>> 633 select SYS_HAS_CPU_MIPS32_R2
>> 634 select SYS_SUPPORTS_32BIT_KERNEL
>> 635 select SYS_SUPPORTS_BIG_ENDIAN
>> 636 select SYS_SUPPORTS_MIPS16
>> 637 select IRQ_MIPS_CPU
>> 638 select SERIAL_8250
>> 639 select SERIAL_8250_CONSOLE
>> 640 select USB_EHCI_BIG_ENDIAN_MMIO
>> 641 select USB_EHCI_BIG_ENDIAN_DESC
>> 642 help
>> 643 This adds support for the PMC-Sierra family of Multi-Service
>> 644 Processor System-On-A-Chips. These parts include a number
>> 645 of integrated peripherals, interfaces and DSPs in addition to
>> 646 a variety of MIPS cores.
>> 647
>> 648 config RALINK
>> 649 bool "Ralink based machines"
>> 650 select CEVT_R4K
>> 651 select CSRC_R4K
>> 652 select BOOT_RAW
>> 653 select DMA_NONCOHERENT
>> 654 select IRQ_MIPS_CPU
>> 655 select USE_OF
>> 656 select SYS_HAS_CPU_MIPS32_R1
>> 657 select SYS_HAS_CPU_MIPS32_R2
>> 658 select SYS_SUPPORTS_32BIT_KERNEL
>> 659 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 660 select SYS_SUPPORTS_MIPS16
>> 661 select SYS_HAS_EARLY_PRINTK
>> 662 select CLKDEV_LOOKUP
>> 663 select ARCH_HAS_RESET_CONTROLLER
>> 664 select RESET_CONTROLLER
>> 665
>> 666 config SGI_IP22
>> 667 bool "SGI IP22 (Indy/Indigo2)"
>> 668 select ARC_MEMORY
>> 669 select ARC_PROMLIB
>> 670 select FW_ARC
>> 671 select FW_ARC32
>> 672 select ARCH_MIGHT_HAVE_PC_SERIO
>> 673 select BOOT_ELF32
>> 674 select CEVT_R4K
>> 675 select CSRC_R4K
>> 676 select DEFAULT_SGI_PARTITION
>> 677 select DMA_NONCOHERENT
>> 678 select HAVE_EISA
>> 679 select I8253
>> 680 select I8259
>> 681 select IP22_CPU_SCACHE
>> 682 select IRQ_MIPS_CPU
>> 683 select GENERIC_ISA_DMA_SUPPORT_BROKEN
>> 684 select SGI_HAS_I8042
>> 685 select SGI_HAS_INDYDOG
>> 686 select SGI_HAS_HAL2
>> 687 select SGI_HAS_SEEQ
>> 688 select SGI_HAS_WD93
>> 689 select SGI_HAS_ZILOG
>> 690 select SWAP_IO_SPACE
>> 691 select SYS_HAS_CPU_R4X00
>> 692 select SYS_HAS_CPU_R5000
>> 693 select SYS_HAS_EARLY_PRINTK
>> 694 select SYS_SUPPORTS_32BIT_KERNEL
>> 695 select SYS_SUPPORTS_64BIT_KERNEL
>> 696 select SYS_SUPPORTS_BIG_ENDIAN
>> 697 select MIPS_L1_CACHE_SHIFT_7
>> 698 help
>> 699 This are the SGI Indy, Challenge S and Indigo2, as well as certain
>> 700 OEM variants like the Tandem CMN B006S. To compile a Linux kernel
>> 701 that runs on these, say Y here.
>> 702
>> 703 config SGI_IP27
>> 704 bool "SGI IP27 (Origin200/2000)"
>> 705 select ARCH_HAS_PHYS_TO_DMA
>> 706 select ARCH_SPARSEMEM_ENABLE
>> 707 select FW_ARC
>> 708 select FW_ARC64
>> 709 select ARC_CMDLINE_ONLY
>> 710 select BOOT_ELF64
>> 711 select DEFAULT_SGI_PARTITION
>> 712 select SYS_HAS_EARLY_PRINTK
>> 713 select HAVE_PCI
>> 714 select IRQ_MIPS_CPU
>> 715 select IRQ_DOMAIN_HIERARCHY
>> 716 select NR_CPUS_DEFAULT_64
>> 717 select PCI_DRIVERS_GENERIC
>> 718 select PCI_XTALK_BRIDGE
>> 719 select SYS_HAS_CPU_R10000
>> 720 select SYS_SUPPORTS_64BIT_KERNEL
>> 721 select SYS_SUPPORTS_BIG_ENDIAN
>> 722 select SYS_SUPPORTS_NUMA
>> 723 select SYS_SUPPORTS_SMP
>> 724 select MIPS_L1_CACHE_SHIFT_7
>> 725 select NUMA
>> 726 help
>> 727 This are the SGI Origin 200, Origin 2000 and Onyx 2 Graphics
>> 728 workstations. To compile a Linux kernel that runs on these, say Y
>> 729 here.
>> 730
>> 731 config SGI_IP28
>> 732 bool "SGI IP28 (Indigo2 R10k)"
>> 733 select ARC_MEMORY
>> 734 select ARC_PROMLIB
>> 735 select FW_ARC
>> 736 select FW_ARC64
>> 737 select ARCH_MIGHT_HAVE_PC_SERIO
>> 738 select BOOT_ELF64
>> 739 select CEVT_R4K
>> 740 select CSRC_R4K
>> 741 select DEFAULT_SGI_PARTITION
>> 742 select DMA_NONCOHERENT
>> 743 select GENERIC_ISA_DMA_SUPPORT_BROKEN
>> 744 select IRQ_MIPS_CPU
>> 745 select HAVE_EISA
>> 746 select I8253
>> 747 select I8259
>> 748 select SGI_HAS_I8042
>> 749 select SGI_HAS_INDYDOG
>> 750 select SGI_HAS_HAL2
>> 751 select SGI_HAS_SEEQ
>> 752 select SGI_HAS_WD93
>> 753 select SGI_HAS_ZILOG
>> 754 select SWAP_IO_SPACE
>> 755 select SYS_HAS_CPU_R10000
>> 756 select SYS_HAS_EARLY_PRINTK
>> 757 select SYS_SUPPORTS_64BIT_KERNEL
>> 758 select SYS_SUPPORTS_BIG_ENDIAN
>> 759 select MIPS_L1_CACHE_SHIFT_7
>> 760 help
>> 761 This is the SGI Indigo2 with R10000 processor. To compile a Linux
>> 762 kernel that runs on these, say Y here.
>> 763
>> 764 config SGI_IP30
>> 765 bool "SGI IP30 (Octane/Octane2)"
>> 766 select ARCH_HAS_PHYS_TO_DMA
>> 767 select FW_ARC
>> 768 select FW_ARC64
>> 769 select BOOT_ELF64
>> 770 select CEVT_R4K
>> 771 select CSRC_R4K
>> 772 select SYNC_R4K if SMP
>> 773 select ZONE_DMA32
>> 774 select HAVE_PCI
>> 775 select IRQ_MIPS_CPU
>> 776 select IRQ_DOMAIN_HIERARCHY
>> 777 select NR_CPUS_DEFAULT_2
>> 778 select PCI_DRIVERS_GENERIC
>> 779 select PCI_XTALK_BRIDGE
>> 780 select SYS_HAS_EARLY_PRINTK
>> 781 select SYS_HAS_CPU_R10000
>> 782 select SYS_SUPPORTS_64BIT_KERNEL
>> 783 select SYS_SUPPORTS_BIG_ENDIAN
>> 784 select SYS_SUPPORTS_SMP
>> 785 select MIPS_L1_CACHE_SHIFT_7
>> 786 select ARC_MEMORY
>> 787 help
>> 788 These are the SGI Octane and Octane2 graphics workstations. To
>> 789 compile a Linux kernel that runs on these, say Y here.
>> 790
>> 791 config SGI_IP32
>> 792 bool "SGI IP32 (O2)"
>> 793 select ARC_MEMORY
>> 794 select ARC_PROMLIB
>> 795 select ARCH_HAS_PHYS_TO_DMA
>> 796 select FW_ARC
>> 797 select FW_ARC32
>> 798 select BOOT_ELF32
>> 799 select CEVT_R4K
>> 800 select CSRC_R4K
>> 801 select DMA_NONCOHERENT
>> 802 select HAVE_PCI
>> 803 select IRQ_MIPS_CPU
>> 804 select R5000_CPU_SCACHE
>> 805 select RM7000_CPU_SCACHE
>> 806 select SYS_HAS_CPU_R5000
>> 807 select SYS_HAS_CPU_R10000 if BROKEN
>> 808 select SYS_HAS_CPU_RM7000
>> 809 select SYS_HAS_CPU_NEVADA
>> 810 select SYS_SUPPORTS_64BIT_KERNEL
>> 811 select SYS_SUPPORTS_BIG_ENDIAN
>> 812 help
>> 813 If you want this kernel to run on SGI O2 workstation, say Y here.
>> 814
>> 815 config SIBYTE_CRHINE
>> 816 bool "Sibyte BCM91120C-CRhine"
>> 817 select BOOT_ELF32
>> 818 select SIBYTE_BCM1120
>> 819 select SWAP_IO_SPACE
>> 820 select SYS_HAS_CPU_SB1
>> 821 select SYS_SUPPORTS_BIG_ENDIAN
>> 822 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 823
>> 824 config SIBYTE_CARMEL
>> 825 bool "Sibyte BCM91120x-Carmel"
>> 826 select BOOT_ELF32
>> 827 select SIBYTE_BCM1120
>> 828 select SWAP_IO_SPACE
>> 829 select SYS_HAS_CPU_SB1
>> 830 select SYS_SUPPORTS_BIG_ENDIAN
>> 831 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 832
>> 833 config SIBYTE_CRHONE
>> 834 bool "Sibyte BCM91125C-CRhone"
>> 835 select BOOT_ELF32
>> 836 select SIBYTE_BCM1125
>> 837 select SWAP_IO_SPACE
>> 838 select SYS_HAS_CPU_SB1
>> 839 select SYS_SUPPORTS_BIG_ENDIAN
>> 840 select SYS_SUPPORTS_HIGHMEM
>> 841 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 842
>> 843 config SIBYTE_RHONE
>> 844 bool "Sibyte BCM91125E-Rhone"
>> 845 select BOOT_ELF32
>> 846 select SIBYTE_BCM1125H
>> 847 select SWAP_IO_SPACE
>> 848 select SYS_HAS_CPU_SB1
>> 849 select SYS_SUPPORTS_BIG_ENDIAN
>> 850 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 851
>> 852 config SIBYTE_SWARM
>> 853 bool "Sibyte BCM91250A-SWARM"
>> 854 select BOOT_ELF32
>> 855 select HAVE_PATA_PLATFORM
>> 856 select SIBYTE_SB1250
>> 857 select SWAP_IO_SPACE
>> 858 select SYS_HAS_CPU_SB1
>> 859 select SYS_SUPPORTS_BIG_ENDIAN
>> 860 select SYS_SUPPORTS_HIGHMEM
>> 861 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 862 select ZONE_DMA32 if 64BIT
>> 863 select SWIOTLB if ARCH_DMA_ADDR_T_64BIT && PCI
>> 864
>> 865 config SIBYTE_LITTLESUR
>> 866 bool "Sibyte BCM91250C2-LittleSur"
>> 867 select BOOT_ELF32
>> 868 select HAVE_PATA_PLATFORM
>> 869 select SIBYTE_SB1250
>> 870 select SWAP_IO_SPACE
>> 871 select SYS_HAS_CPU_SB1
>> 872 select SYS_SUPPORTS_BIG_ENDIAN
>> 873 select SYS_SUPPORTS_HIGHMEM
>> 874 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 875 select ZONE_DMA32 if 64BIT
>> 876
>> 877 config SIBYTE_SENTOSA
>> 878 bool "Sibyte BCM91250E-Sentosa"
>> 879 select BOOT_ELF32
>> 880 select SIBYTE_SB1250
>> 881 select SWAP_IO_SPACE
>> 882 select SYS_HAS_CPU_SB1
>> 883 select SYS_SUPPORTS_BIG_ENDIAN
>> 884 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 885 select SWIOTLB if ARCH_DMA_ADDR_T_64BIT && PCI
>> 886
>> 887 config SIBYTE_BIGSUR
>> 888 bool "Sibyte BCM91480B-BigSur"
>> 889 select BOOT_ELF32
>> 890 select NR_CPUS_DEFAULT_4
>> 891 select SIBYTE_BCM1x80
>> 892 select SWAP_IO_SPACE
>> 893 select SYS_HAS_CPU_SB1
>> 894 select SYS_SUPPORTS_BIG_ENDIAN
>> 895 select SYS_SUPPORTS_HIGHMEM
>> 896 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 897 select ZONE_DMA32 if 64BIT
>> 898 select SWIOTLB if ARCH_DMA_ADDR_T_64BIT && PCI
>> 899
>> 900 config SNI_RM
>> 901 bool "SNI RM200/300/400"
>> 902 select ARC_MEMORY
>> 903 select ARC_PROMLIB
>> 904 select FW_ARC if CPU_LITTLE_ENDIAN
>> 905 select FW_ARC32 if CPU_LITTLE_ENDIAN
>> 906 select FW_SNIPROM if CPU_BIG_ENDIAN
>> 907 select ARCH_MAY_HAVE_PC_FDC
>> 908 select ARCH_MIGHT_HAVE_PC_PARPORT
>> 909 select ARCH_MIGHT_HAVE_PC_SERIO
>> 910 select BOOT_ELF32
>> 911 select CEVT_R4K
>> 912 select CSRC_R4K
>> 913 select DEFAULT_SGI_PARTITION if CPU_BIG_ENDIAN
>> 914 select DMA_NONCOHERENT
>> 915 select GENERIC_ISA_DMA
>> 916 select HAVE_EISA
>> 917 select HAVE_PCSPKR_PLATFORM
>> 918 select HAVE_PCI
>> 919 select IRQ_MIPS_CPU
>> 920 select I8253
>> 921 select I8259
>> 922 select ISA
>> 923 select SWAP_IO_SPACE if CPU_BIG_ENDIAN
>> 924 select SYS_HAS_CPU_R4X00
>> 925 select SYS_HAS_CPU_R5000
>> 926 select SYS_HAS_CPU_R10000
>> 927 select R5000_CPU_SCACHE
>> 928 select SYS_HAS_EARLY_PRINTK
>> 929 select SYS_SUPPORTS_32BIT_KERNEL
>> 930 select SYS_SUPPORTS_64BIT_KERNEL
>> 931 select SYS_SUPPORTS_BIG_ENDIAN
>> 932 select SYS_SUPPORTS_HIGHMEM
>> 933 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 934 help
>> 935 The SNI RM200/300/400 are MIPS-based machines manufactured by
>> 936 Siemens Nixdorf Informationssysteme (SNI), parent company of Pyramid
>> 937 Technology and now in turn merged with Fujitsu. Say Y here to
>> 938 support this machine type.
>> 939
>> 940 config MACH_TX39XX
>> 941 bool "Toshiba TX39 series based machines"
>> 942
>> 943 config MACH_TX49XX
>> 944 bool "Toshiba TX49 series based machines"
>> 945
>> 946 config MIKROTIK_RB532
>> 947 bool "Mikrotik RB532 boards"
>> 948 select CEVT_R4K
>> 949 select CSRC_R4K
>> 950 select DMA_NONCOHERENT
>> 951 select HAVE_PCI
>> 952 select IRQ_MIPS_CPU
>> 953 select SYS_HAS_CPU_MIPS32_R1
>> 954 select SYS_SUPPORTS_32BIT_KERNEL
>> 955 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 956 select SWAP_IO_SPACE
>> 957 select BOOT_RAW
>> 958 select GPIOLIB
>> 959 select MIPS_L1_CACHE_SHIFT_4
>> 960 help
>> 961 Support the Mikrotik(tm) RouterBoard 532 series,
>> 962 based on the IDT RC32434 SoC.
>> 963
>> 964 config CAVIUM_OCTEON_SOC
>> 965 bool "Cavium Networks Octeon SoC based boards"
>> 966 select CEVT_R4K
>> 967 select ARCH_HAS_PHYS_TO_DMA
>> 968 select HAVE_RAPIDIO
>> 969 select PHYS_ADDR_T_64BIT
>> 970 select SYS_SUPPORTS_64BIT_KERNEL
>> 971 select SYS_SUPPORTS_BIG_ENDIAN
>> 972 select EDAC_SUPPORT
>> 973 select EDAC_ATOMIC_SCRUB
>> 974 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 975 select SYS_SUPPORTS_HOTPLUG_CPU if CPU_BIG_ENDIAN
>> 976 select SYS_HAS_EARLY_PRINTK
>> 977 select SYS_HAS_CPU_CAVIUM_OCTEON
>> 978 select HAVE_PCI
>> 979 select HAVE_PLAT_DELAY
>> 980 select HAVE_PLAT_FW_INIT_CMDLINE
>> 981 select HAVE_PLAT_MEMCPY
>> 982 select ZONE_DMA32
>> 983 select HOLES_IN_ZONE
>> 984 select GPIOLIB
>> 985 select USE_OF
>> 986 select ARCH_SPARSEMEM_ENABLE
>> 987 select SYS_SUPPORTS_SMP
>> 988 select NR_CPUS_DEFAULT_64
>> 989 select MIPS_NR_CPU_NR_MAP_1024
>> 990 select BUILTIN_DTB
>> 991 select MTD_COMPLEX_MAPPINGS
>> 992 select SWIOTLB
>> 993 select SYS_SUPPORTS_RELOCATABLE
>> 994 help
>> 995 This option supports all of the Octeon reference boards from Cavium
>> 996 Networks. It builds a kernel that dynamically determines the Octeon
>> 997 CPU type and supports all known board reference implementations.
>> 998 Some of the supported boards are:
>> 999 EBT3000
>> 1000 EBH3000
>> 1001 EBH3100
>> 1002 Thunder
>> 1003 Kodama
>> 1004 Hikari
>> 1005 Say Y here for most Octeon reference boards.
>> 1006
>> 1007 config NLM_XLR_BOARD
>> 1008 bool "Netlogic XLR/XLS based systems"
>> 1009 select BOOT_ELF32
>> 1010 select NLM_COMMON
>> 1011 select SYS_HAS_CPU_XLR
>> 1012 select SYS_SUPPORTS_SMP
>> 1013 select HAVE_PCI
>> 1014 select SWAP_IO_SPACE
>> 1015 select SYS_SUPPORTS_32BIT_KERNEL
>> 1016 select SYS_SUPPORTS_64BIT_KERNEL
>> 1017 select PHYS_ADDR_T_64BIT
>> 1018 select SYS_SUPPORTS_BIG_ENDIAN
>> 1019 select SYS_SUPPORTS_HIGHMEM
>> 1020 select NR_CPUS_DEFAULT_32
>> 1021 select CEVT_R4K
>> 1022 select CSRC_R4K
>> 1023 select IRQ_MIPS_CPU
>> 1024 select ZONE_DMA32 if 64BIT
>> 1025 select SYNC_R4K
>> 1026 select SYS_HAS_EARLY_PRINTK
>> 1027 select SYS_SUPPORTS_ZBOOT
>> 1028 select SYS_SUPPORTS_ZBOOT_UART16550
>> 1029 help
>> 1030 Support for systems based on Netlogic XLR and XLS processors.
>> 1031 Say Y here if you have a XLR or XLS based board.
>> 1032
>> 1033 config NLM_XLP_BOARD
>> 1034 bool "Netlogic XLP based systems"
>> 1035 select BOOT_ELF32
>> 1036 select NLM_COMMON
>> 1037 select SYS_HAS_CPU_XLP
>> 1038 select SYS_SUPPORTS_SMP
>> 1039 select HAVE_PCI
>> 1040 select SYS_SUPPORTS_32BIT_KERNEL
>> 1041 select SYS_SUPPORTS_64BIT_KERNEL
>> 1042 select PHYS_ADDR_T_64BIT
>> 1043 select GPIOLIB
>> 1044 select SYS_SUPPORTS_BIG_ENDIAN
>> 1045 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 1046 select SYS_SUPPORTS_HIGHMEM
>> 1047 select NR_CPUS_DEFAULT_32
>> 1048 select CEVT_R4K
>> 1049 select CSRC_R4K
>> 1050 select IRQ_MIPS_CPU
>> 1051 select ZONE_DMA32 if 64BIT
>> 1052 select SYNC_R4K
>> 1053 select SYS_HAS_EARLY_PRINTK
>> 1054 select USE_OF
>> 1055 select SYS_SUPPORTS_ZBOOT
>> 1056 select SYS_SUPPORTS_ZBOOT_UART16550
>> 1057 help
>> 1058 This board is based on Netlogic XLP Processor.
>> 1059 Say Y here if you have a XLP based board.
>> 1060
>> 1061 config MIPS_PARAVIRT
>> 1062 bool "Para-Virtualized guest system"
>> 1063 select CEVT_R4K
>> 1064 select CSRC_R4K
>> 1065 select SYS_SUPPORTS_64BIT_KERNEL
>> 1066 select SYS_SUPPORTS_32BIT_KERNEL
>> 1067 select SYS_SUPPORTS_BIG_ENDIAN
>> 1068 select SYS_SUPPORTS_SMP
>> 1069 select NR_CPUS_DEFAULT_4
>> 1070 select SYS_HAS_EARLY_PRINTK
>> 1071 select SYS_HAS_CPU_MIPS32_R2
>> 1072 select SYS_HAS_CPU_MIPS64_R2
>> 1073 select SYS_HAS_CPU_CAVIUM_OCTEON
>> 1074 select HAVE_PCI
>> 1075 select SWAP_IO_SPACE
>> 1076 help
>> 1077 This option supports guest running under ????
>> 1078
>> 1079 endchoice
>> 1080
>> 1081 source "arch/mips/alchemy/Kconfig"
>> 1082 source "arch/mips/ath25/Kconfig"
>> 1083 source "arch/mips/ath79/Kconfig"
>> 1084 source "arch/mips/bcm47xx/Kconfig"
>> 1085 source "arch/mips/bcm63xx/Kconfig"
>> 1086 source "arch/mips/bmips/Kconfig"
>> 1087 source "arch/mips/generic/Kconfig"
>> 1088 source "arch/mips/jazz/Kconfig"
>> 1089 source "arch/mips/jz4740/Kconfig"
>> 1090 source "arch/mips/lantiq/Kconfig"
>> 1091 source "arch/mips/lasat/Kconfig"
>> 1092 source "arch/mips/pic32/Kconfig"
>> 1093 source "arch/mips/pistachio/Kconfig"
>> 1094 source "arch/mips/pmcs-msp71xx/Kconfig"
>> 1095 source "arch/mips/ralink/Kconfig"
>> 1096 source "arch/mips/sgi-ip27/Kconfig"
>> 1097 source "arch/mips/sibyte/Kconfig"
>> 1098 source "arch/mips/txx9/Kconfig"
>> 1099 source "arch/mips/vr41xx/Kconfig"
>> 1100 source "arch/mips/cavium-octeon/Kconfig"
>> 1101 source "arch/mips/loongson2ef/Kconfig"
>> 1102 source "arch/mips/loongson32/Kconfig"
>> 1103 source "arch/mips/loongson64/Kconfig"
>> 1104 source "arch/mips/netlogic/Kconfig"
>> 1105 source "arch/mips/paravirt/Kconfig"
>> 1106
>> 1107 endmenu
>> 1108
>> 1109 config GENERIC_HWEIGHT
>> 1110 bool
>> 1111 default y
>> 1112
>> 1113 config GENERIC_CALIBRATE_DELAY
>> 1114 bool
>> 1115 default y
>> 1116
>> 1117 config SCHED_OMIT_FRAME_POINTER
>> 1118 bool
>> 1119 default y
>> 1120
>> 1121 #
>> 1122 # Select some configuration options automatically based on user selections.
>> 1123 #
>> 1124 config FW_ARC
>> 1125 bool
>> 1126
>> 1127 config ARCH_MAY_HAVE_PC_FDC
>> 1128 bool
>> 1129
>> 1130 config BOOT_RAW
>> 1131 bool
>> 1132
>> 1133 config CEVT_BCM1480
>> 1134 bool
>> 1135
>> 1136 config CEVT_DS1287
>> 1137 bool
49 1138
50 # Endianness selection !! 1139 config CEVT_GT641XX
>> 1140 bool
>> 1141
>> 1142 config CEVT_R4K
>> 1143 bool
>> 1144
>> 1145 config CEVT_SB1250
>> 1146 bool
>> 1147
>> 1148 config CEVT_TXX9
>> 1149 bool
>> 1150
>> 1151 config CSRC_BCM1480
>> 1152 bool
>> 1153
>> 1154 config CSRC_IOASIC
>> 1155 bool
>> 1156
>> 1157 config CSRC_R4K
>> 1158 bool
>> 1159
>> 1160 config CSRC_SB1250
>> 1161 bool
>> 1162
>> 1163 config MIPS_CLOCK_VSYSCALL
>> 1164 def_bool CSRC_R4K || CLKSRC_MIPS_GIC
>> 1165
>> 1166 config GPIO_TXX9
>> 1167 select GPIOLIB
>> 1168 bool
>> 1169
>> 1170 config FW_CFE
>> 1171 bool
>> 1172
>> 1173 config ARCH_SUPPORTS_UPROBES
>> 1174 bool
>> 1175
>> 1176 config DMA_MAYBE_COHERENT
>> 1177 select ARCH_HAS_DMA_COHERENCE_H
>> 1178 select DMA_NONCOHERENT
>> 1179 bool
>> 1180
>> 1181 config DMA_PERDEV_COHERENT
>> 1182 bool
>> 1183 select ARCH_HAS_SETUP_DMA_OPS
>> 1184 select DMA_NONCOHERENT
>> 1185
>> 1186 config DMA_NONCOHERENT
>> 1187 bool
>> 1188 #
>> 1189 # MIPS allows mixing "slightly different" Cacheability and Coherency
>> 1190 # Attribute bits. It is believed that the uncached access through
>> 1191 # KSEG1 and the implementation specific "uncached accelerated" used
>> 1192 # by pgprot_writcombine can be mixed, and the latter sometimes provides
>> 1193 # significant advantages.
>> 1194 #
>> 1195 select ARCH_HAS_DMA_WRITE_COMBINE
>> 1196 select ARCH_HAS_DMA_PREP_COHERENT
>> 1197 select ARCH_HAS_SYNC_DMA_FOR_DEVICE
>> 1198 select ARCH_HAS_DMA_SET_UNCACHED
>> 1199 select DMA_NONCOHERENT_MMAP
>> 1200 select DMA_NONCOHERENT_CACHE_SYNC
>> 1201 select NEED_DMA_MAP_STATE
>> 1202
>> 1203 config SYS_HAS_EARLY_PRINTK
>> 1204 bool
>> 1205
>> 1206 config SYS_SUPPORTS_HOTPLUG_CPU
>> 1207 bool
>> 1208
>> 1209 config MIPS_BONITO64
>> 1210 bool
>> 1211
>> 1212 config MIPS_MSC
>> 1213 bool
>> 1214
>> 1215 config MIPS_NILE4
>> 1216 bool
>> 1217
>> 1218 config SYNC_R4K
>> 1219 bool
>> 1220
>> 1221 config MIPS_MACHINE
>> 1222 def_bool n
>> 1223
>> 1224 config NO_IOPORT_MAP
>> 1225 def_bool n
>> 1226
>> 1227 config GENERIC_CSUM
>> 1228 def_bool CPU_NO_LOAD_STORE_LR
>> 1229
>> 1230 config GENERIC_ISA_DMA
>> 1231 bool
>> 1232 select ZONE_DMA if GENERIC_ISA_DMA_SUPPORT_BROKEN=n
>> 1233 select ISA_DMA_API
>> 1234
>> 1235 config GENERIC_ISA_DMA_SUPPORT_BROKEN
>> 1236 bool
>> 1237 select GENERIC_ISA_DMA
>> 1238
>> 1239 config HAVE_PLAT_DELAY
>> 1240 bool
>> 1241
>> 1242 config HAVE_PLAT_FW_INIT_CMDLINE
>> 1243 bool
>> 1244
>> 1245 config HAVE_PLAT_MEMCPY
>> 1246 bool
>> 1247
>> 1248 config ISA_DMA_API
>> 1249 bool
>> 1250
>> 1251 config HOLES_IN_ZONE
>> 1252 bool
>> 1253
>> 1254 config SYS_SUPPORTS_RELOCATABLE
>> 1255 bool
>> 1256 help
>> 1257 Selected if the platform supports relocating the kernel.
>> 1258 The platform must provide plat_get_fdt() if it selects CONFIG_USE_OF
>> 1259 to allow access to command line and entropy sources.
>> 1260
>> 1261 config MIPS_CBPF_JIT
>> 1262 def_bool y
>> 1263 depends on BPF_JIT && HAVE_CBPF_JIT
>> 1264
>> 1265 config MIPS_EBPF_JIT
>> 1266 def_bool y
>> 1267 depends on BPF_JIT && HAVE_EBPF_JIT
>> 1268
>> 1269
>> 1270 #
>> 1271 # Endianness selection. Sufficiently obscure so many users don't know what to
>> 1272 # answer,so we try hard to limit the available choices. Also the use of a
>> 1273 # choice statement should be more obvious to the user.
>> 1274 #
51 choice 1275 choice
52 prompt "Endianness selection" 1276 prompt "Endianness selection"
53 default CPU_LITTLE_ENDIAN <<
54 help 1277 help
55 microblaze architectures can be conf !! 1278 Some MIPS machines can be configured for either little or big endian
56 big endian formats. Be sure to selec !! 1279 byte order. These modes require different kernels and a different
>> 1280 Linux distribution. In general there is one preferred byteorder for a
>> 1281 particular system but some systems are just as commonly used in the
>> 1282 one or the other endianness.
57 1283
58 config CPU_BIG_ENDIAN 1284 config CPU_BIG_ENDIAN
59 bool "Big endian" 1285 bool "Big endian"
>> 1286 depends on SYS_SUPPORTS_BIG_ENDIAN
60 1287
61 config CPU_LITTLE_ENDIAN 1288 config CPU_LITTLE_ENDIAN
62 bool "Little endian" 1289 bool "Little endian"
>> 1290 depends on SYS_SUPPORTS_LITTLE_ENDIAN
63 1291
64 endchoice 1292 endchoice
65 1293
66 config ARCH_HAS_ILOG2_U32 !! 1294 config EXPORT_UASM
67 def_bool n !! 1295 bool
68 1296
69 config ARCH_HAS_ILOG2_U64 !! 1297 config SYS_SUPPORTS_APM_EMULATION
70 def_bool n !! 1298 bool
71 1299
72 config GENERIC_HWEIGHT !! 1300 config SYS_SUPPORTS_BIG_ENDIAN
73 def_bool y !! 1301 bool
74 1302
75 config GENERIC_CALIBRATE_DELAY !! 1303 config SYS_SUPPORTS_LITTLE_ENDIAN
76 def_bool y !! 1304 bool
77 1305
78 config GENERIC_CSUM !! 1306 config SYS_SUPPORTS_HUGETLBFS
>> 1307 bool
>> 1308 depends on CPU_SUPPORTS_HUGEPAGES
>> 1309 default y
>> 1310
>> 1311 config MIPS_HUGE_TLB_SUPPORT
>> 1312 def_bool HUGETLB_PAGE || TRANSPARENT_HUGEPAGE
>> 1313
>> 1314 config IRQ_CPU_RM7K
>> 1315 bool
>> 1316
>> 1317 config IRQ_MSP_SLP
>> 1318 bool
>> 1319
>> 1320 config IRQ_MSP_CIC
>> 1321 bool
>> 1322
>> 1323 config IRQ_TXX9
>> 1324 bool
>> 1325
>> 1326 config IRQ_GT641XX
>> 1327 bool
>> 1328
>> 1329 config PCI_GT64XXX_PCI0
>> 1330 bool
>> 1331
>> 1332 config PCI_XTALK_BRIDGE
>> 1333 bool
>> 1334
>> 1335 config NO_EXCEPT_FILL
>> 1336 bool
>> 1337
>> 1338 config SOC_EMMA2RH
>> 1339 bool
>> 1340 select CEVT_R4K
>> 1341 select CSRC_R4K
>> 1342 select DMA_NONCOHERENT
>> 1343 select IRQ_MIPS_CPU
>> 1344 select SWAP_IO_SPACE
>> 1345 select SYS_HAS_CPU_R5500
>> 1346 select SYS_SUPPORTS_32BIT_KERNEL
>> 1347 select SYS_SUPPORTS_64BIT_KERNEL
>> 1348 select SYS_SUPPORTS_BIG_ENDIAN
>> 1349
>> 1350 config SOC_PNX833X
>> 1351 bool
>> 1352 select CEVT_R4K
>> 1353 select CSRC_R4K
>> 1354 select IRQ_MIPS_CPU
>> 1355 select DMA_NONCOHERENT
>> 1356 select SYS_HAS_CPU_MIPS32_R2
>> 1357 select SYS_SUPPORTS_32BIT_KERNEL
>> 1358 select SYS_SUPPORTS_LITTLE_ENDIAN
>> 1359 select SYS_SUPPORTS_BIG_ENDIAN
>> 1360 select SYS_SUPPORTS_MIPS16
>> 1361 select CPU_MIPSR2_IRQ_VI
>> 1362
>> 1363 config SOC_PNX8335
>> 1364 bool
>> 1365 select SOC_PNX833X
>> 1366
>> 1367 config MIPS_SPRAM
>> 1368 bool
>> 1369
>> 1370 config SWAP_IO_SPACE
>> 1371 bool
>> 1372
>> 1373 config SGI_HAS_INDYDOG
>> 1374 bool
>> 1375
>> 1376 config SGI_HAS_HAL2
>> 1377 bool
>> 1378
>> 1379 config SGI_HAS_SEEQ
>> 1380 bool
>> 1381
>> 1382 config SGI_HAS_WD93
>> 1383 bool
>> 1384
>> 1385 config SGI_HAS_ZILOG
>> 1386 bool
>> 1387
>> 1388 config SGI_HAS_I8042
>> 1389 bool
>> 1390
>> 1391 config DEFAULT_SGI_PARTITION
>> 1392 bool
>> 1393
>> 1394 config FW_ARC32
>> 1395 bool
>> 1396
>> 1397 config FW_SNIPROM
>> 1398 bool
>> 1399
>> 1400 config BOOT_ELF32
>> 1401 bool
>> 1402
>> 1403 config MIPS_L1_CACHE_SHIFT_4
>> 1404 bool
>> 1405
>> 1406 config MIPS_L1_CACHE_SHIFT_5
>> 1407 bool
>> 1408
>> 1409 config MIPS_L1_CACHE_SHIFT_6
>> 1410 bool
>> 1411
>> 1412 config MIPS_L1_CACHE_SHIFT_7
>> 1413 bool
>> 1414
>> 1415 config MIPS_L1_CACHE_SHIFT
>> 1416 int
>> 1417 default "7" if MIPS_L1_CACHE_SHIFT_7
>> 1418 default "6" if MIPS_L1_CACHE_SHIFT_6
>> 1419 default "5" if MIPS_L1_CACHE_SHIFT_5
>> 1420 default "4" if MIPS_L1_CACHE_SHIFT_4
>> 1421 default "5"
>> 1422
>> 1423 config HAVE_STD_PC_SERIAL_PORT
>> 1424 bool
>> 1425
>> 1426 config ARC_CMDLINE_ONLY
>> 1427 bool
>> 1428
>> 1429 config ARC_CONSOLE
>> 1430 bool "ARC console support"
>> 1431 depends on SGI_IP22 || SGI_IP28 || (SNI_RM && CPU_LITTLE_ENDIAN)
>> 1432
>> 1433 config ARC_MEMORY
>> 1434 bool
>> 1435
>> 1436 config ARC_PROMLIB
>> 1437 bool
>> 1438
>> 1439 config FW_ARC64
>> 1440 bool
>> 1441
>> 1442 config BOOT_ELF64
>> 1443 bool
>> 1444
>> 1445 menu "CPU selection"
>> 1446
>> 1447 choice
>> 1448 prompt "CPU type"
>> 1449 default CPU_R4X00
>> 1450
>> 1451 config CPU_LOONGSON64
>> 1452 bool "Loongson 64-bit CPU"
>> 1453 depends on SYS_HAS_CPU_LOONGSON64
>> 1454 select ARCH_HAS_PHYS_TO_DMA
>> 1455 select CPU_MIPSR2
>> 1456 select CPU_HAS_PREFETCH
>> 1457 select CPU_SUPPORTS_64BIT_KERNEL
>> 1458 select CPU_SUPPORTS_HIGHMEM
>> 1459 select CPU_SUPPORTS_HUGEPAGES
>> 1460 select CPU_SUPPORTS_MSA
>> 1461 select CPU_DIEI_BROKEN if !LOONGSON3_ENHANCEMENT
>> 1462 select CPU_MIPSR2_IRQ_VI
>> 1463 select WEAK_ORDERING
>> 1464 select WEAK_REORDERING_BEYOND_LLSC
>> 1465 select MIPS_ASID_BITS_VARIABLE
>> 1466 select MIPS_PGD_C0_CONTEXT
>> 1467 select MIPS_L1_CACHE_SHIFT_6
>> 1468 select GPIOLIB
>> 1469 select SWIOTLB
>> 1470 help
>> 1471 The Loongson GSx64(GS264/GS464/GS464E/GS464V) series of processor
>> 1472 cores implements the MIPS64R2 instruction set with many extensions,
>> 1473 including most 64-bit Loongson-2 (2H, 2K) and Loongson-3 (3A1000,
>> 1474 3B1000, 3B1500, 3A2000, 3A3000 and 3A4000) processors. However, old
>> 1475 Loongson-2E/2F is not covered here and will be removed in future.
>> 1476
>> 1477 config LOONGSON3_ENHANCEMENT
>> 1478 bool "New Loongson-3 CPU Enhancements"
>> 1479 default n
>> 1480 depends on CPU_LOONGSON64
>> 1481 help
>> 1482 New Loongson-3 cores (since Loongson-3A R2, as opposed to Loongson-3A
>> 1483 R1, Loongson-3B R1 and Loongson-3B R2) has many enhancements, such as
>> 1484 FTLB, L1-VCache, EI/DI/Wait/Prefetch instruction, DSP/DSPr2 ASE, User
>> 1485 Local register, Read-Inhibit/Execute-Inhibit, SFB (Store Fill Buffer),
>> 1486 Fast TLB refill support, etc.
>> 1487
>> 1488 This option enable those enhancements which are not probed at run
>> 1489 time. If you want a generic kernel to run on all Loongson 3 machines,
>> 1490 please say 'N' here. If you want a high-performance kernel to run on
>> 1491 new Loongson-3 machines only, please say 'Y' here.
>> 1492
>> 1493 config CPU_LOONGSON3_WORKAROUNDS
>> 1494 bool "Old Loongson-3 LLSC Workarounds"
>> 1495 default y if SMP
>> 1496 depends on CPU_LOONGSON64
>> 1497 help
>> 1498 Loongson-3 processors have the llsc issues which require workarounds.
>> 1499 Without workarounds the system may hang unexpectedly.
>> 1500
>> 1501 Newer Loongson-3 will fix these issues and no workarounds are needed.
>> 1502 The workarounds have no significant side effect on them but may
>> 1503 decrease the performance of the system so this option should be
>> 1504 disabled unless the kernel is intended to be run on old systems.
>> 1505
>> 1506 If unsure, please say Y.
>> 1507
>> 1508 config CPU_LOONGSON2E
>> 1509 bool "Loongson 2E"
>> 1510 depends on SYS_HAS_CPU_LOONGSON2E
>> 1511 select CPU_LOONGSON2EF
>> 1512 help
>> 1513 The Loongson 2E processor implements the MIPS III instruction set
>> 1514 with many extensions.
>> 1515
>> 1516 It has an internal FPGA northbridge, which is compatible to
>> 1517 bonito64.
>> 1518
>> 1519 config CPU_LOONGSON2F
>> 1520 bool "Loongson 2F"
>> 1521 depends on SYS_HAS_CPU_LOONGSON2F
>> 1522 select CPU_LOONGSON2EF
>> 1523 select GPIOLIB
>> 1524 help
>> 1525 The Loongson 2F processor implements the MIPS III instruction set
>> 1526 with many extensions.
>> 1527
>> 1528 Loongson2F have built-in DDR2 and PCIX controller. The PCIX controller
>> 1529 have a similar programming interface with FPGA northbridge used in
>> 1530 Loongson2E.
>> 1531
>> 1532 config CPU_LOONGSON1B
>> 1533 bool "Loongson 1B"
>> 1534 depends on SYS_HAS_CPU_LOONGSON1B
>> 1535 select CPU_LOONGSON32
>> 1536 select LEDS_GPIO_REGISTER
>> 1537 help
>> 1538 The Loongson 1B is a 32-bit SoC, which implements the MIPS32
>> 1539 Release 1 instruction set and part of the MIPS32 Release 2
>> 1540 instruction set.
>> 1541
>> 1542 config CPU_LOONGSON1C
>> 1543 bool "Loongson 1C"
>> 1544 depends on SYS_HAS_CPU_LOONGSON1C
>> 1545 select CPU_LOONGSON32
>> 1546 select LEDS_GPIO_REGISTER
>> 1547 help
>> 1548 The Loongson 1C is a 32-bit SoC, which implements the MIPS32
>> 1549 Release 1 instruction set and part of the MIPS32 Release 2
>> 1550 instruction set.
>> 1551
>> 1552 config CPU_MIPS32_R1
>> 1553 bool "MIPS32 Release 1"
>> 1554 depends on SYS_HAS_CPU_MIPS32_R1
>> 1555 select CPU_HAS_PREFETCH
>> 1556 select CPU_SUPPORTS_32BIT_KERNEL
>> 1557 select CPU_SUPPORTS_HIGHMEM
>> 1558 help
>> 1559 Choose this option to build a kernel for release 1 or later of the
>> 1560 MIPS32 architecture. Most modern embedded systems with a 32-bit
>> 1561 MIPS processor are based on a MIPS32 processor. If you know the
>> 1562 specific type of processor in your system, choose those that one
>> 1563 otherwise CPU_MIPS32_R1 is a safe bet for any MIPS32 system.
>> 1564 Release 2 of the MIPS32 architecture is available since several
>> 1565 years so chances are you even have a MIPS32 Release 2 processor
>> 1566 in which case you should choose CPU_MIPS32_R2 instead for better
>> 1567 performance.
>> 1568
>> 1569 config CPU_MIPS32_R2
>> 1570 bool "MIPS32 Release 2"
>> 1571 depends on SYS_HAS_CPU_MIPS32_R2
>> 1572 select CPU_HAS_PREFETCH
>> 1573 select CPU_SUPPORTS_32BIT_KERNEL
>> 1574 select CPU_SUPPORTS_HIGHMEM
>> 1575 select CPU_SUPPORTS_MSA
>> 1576 select HAVE_KVM
>> 1577 help
>> 1578 Choose this option to build a kernel for release 2 or later of the
>> 1579 MIPS32 architecture. Most modern embedded systems with a 32-bit
>> 1580 MIPS processor are based on a MIPS32 processor. If you know the
>> 1581 specific type of processor in your system, choose those that one
>> 1582 otherwise CPU_MIPS32_R1 is a safe bet for any MIPS32 system.
>> 1583
>> 1584 config CPU_MIPS32_R6
>> 1585 bool "MIPS32 Release 6"
>> 1586 depends on SYS_HAS_CPU_MIPS32_R6
>> 1587 select CPU_HAS_PREFETCH
>> 1588 select CPU_NO_LOAD_STORE_LR
>> 1589 select CPU_SUPPORTS_32BIT_KERNEL
>> 1590 select CPU_SUPPORTS_HIGHMEM
>> 1591 select CPU_SUPPORTS_MSA
>> 1592 select HAVE_KVM
>> 1593 select MIPS_O32_FP64_SUPPORT
>> 1594 help
>> 1595 Choose this option to build a kernel for release 6 or later of the
>> 1596 MIPS32 architecture. New MIPS processors, starting with the Warrior
>> 1597 family, are based on a MIPS32r6 processor. If you own an older
>> 1598 processor, you probably need to select MIPS32r1 or MIPS32r2 instead.
>> 1599
>> 1600 config CPU_MIPS64_R1
>> 1601 bool "MIPS64 Release 1"
>> 1602 depends on SYS_HAS_CPU_MIPS64_R1
>> 1603 select CPU_HAS_PREFETCH
>> 1604 select CPU_SUPPORTS_32BIT_KERNEL
>> 1605 select CPU_SUPPORTS_64BIT_KERNEL
>> 1606 select CPU_SUPPORTS_HIGHMEM
>> 1607 select CPU_SUPPORTS_HUGEPAGES
>> 1608 help
>> 1609 Choose this option to build a kernel for release 1 or later of the
>> 1610 MIPS64 architecture. Many modern embedded systems with a 64-bit
>> 1611 MIPS processor are based on a MIPS64 processor. If you know the
>> 1612 specific type of processor in your system, choose those that one
>> 1613 otherwise CPU_MIPS64_R1 is a safe bet for any MIPS64 system.
>> 1614 Release 2 of the MIPS64 architecture is available since several
>> 1615 years so chances are you even have a MIPS64 Release 2 processor
>> 1616 in which case you should choose CPU_MIPS64_R2 instead for better
>> 1617 performance.
>> 1618
>> 1619 config CPU_MIPS64_R2
>> 1620 bool "MIPS64 Release 2"
>> 1621 depends on SYS_HAS_CPU_MIPS64_R2
>> 1622 select CPU_HAS_PREFETCH
>> 1623 select CPU_SUPPORTS_32BIT_KERNEL
>> 1624 select CPU_SUPPORTS_64BIT_KERNEL
>> 1625 select CPU_SUPPORTS_HIGHMEM
>> 1626 select CPU_SUPPORTS_HUGEPAGES
>> 1627 select CPU_SUPPORTS_MSA
>> 1628 select HAVE_KVM
>> 1629 help
>> 1630 Choose this option to build a kernel for release 2 or later of the
>> 1631 MIPS64 architecture. Many modern embedded systems with a 64-bit
>> 1632 MIPS processor are based on a MIPS64 processor. If you know the
>> 1633 specific type of processor in your system, choose those that one
>> 1634 otherwise CPU_MIPS64_R1 is a safe bet for any MIPS64 system.
>> 1635
>> 1636 config CPU_MIPS64_R6
>> 1637 bool "MIPS64 Release 6"
>> 1638 depends on SYS_HAS_CPU_MIPS64_R6
>> 1639 select CPU_HAS_PREFETCH
>> 1640 select CPU_NO_LOAD_STORE_LR
>> 1641 select CPU_SUPPORTS_32BIT_KERNEL
>> 1642 select CPU_SUPPORTS_64BIT_KERNEL
>> 1643 select CPU_SUPPORTS_HIGHMEM
>> 1644 select CPU_SUPPORTS_HUGEPAGES
>> 1645 select CPU_SUPPORTS_MSA
>> 1646 select MIPS_O32_FP64_SUPPORT if 32BIT || MIPS32_O32
>> 1647 select HAVE_KVM
>> 1648 help
>> 1649 Choose this option to build a kernel for release 6 or later of the
>> 1650 MIPS64 architecture. New MIPS processors, starting with the Warrior
>> 1651 family, are based on a MIPS64r6 processor. If you own an older
>> 1652 processor, you probably need to select MIPS64r1 or MIPS64r2 instead.
>> 1653
>> 1654 config CPU_R3000
>> 1655 bool "R3000"
>> 1656 depends on SYS_HAS_CPU_R3000
>> 1657 select CPU_HAS_WB
>> 1658 select CPU_R3K_TLB
>> 1659 select CPU_SUPPORTS_32BIT_KERNEL
>> 1660 select CPU_SUPPORTS_HIGHMEM
>> 1661 help
>> 1662 Please make sure to pick the right CPU type. Linux/MIPS is not
>> 1663 designed to be generic, i.e. Kernels compiled for R3000 CPUs will
>> 1664 *not* work on R4000 machines and vice versa. However, since most
>> 1665 of the supported machines have an R4000 (or similar) CPU, R4x00
>> 1666 might be a safe bet. If the resulting kernel does not work,
>> 1667 try to recompile with R3000.
>> 1668
>> 1669 config CPU_TX39XX
>> 1670 bool "R39XX"
>> 1671 depends on SYS_HAS_CPU_TX39XX
>> 1672 select CPU_SUPPORTS_32BIT_KERNEL
>> 1673 select CPU_R3K_TLB
>> 1674
>> 1675 config CPU_VR41XX
>> 1676 bool "R41xx"
>> 1677 depends on SYS_HAS_CPU_VR41XX
>> 1678 select CPU_SUPPORTS_32BIT_KERNEL
>> 1679 select CPU_SUPPORTS_64BIT_KERNEL
>> 1680 help
>> 1681 The options selects support for the NEC VR4100 series of processors.
>> 1682 Only choose this option if you have one of these processors as a
>> 1683 kernel built with this option will not run on any other type of
>> 1684 processor or vice versa.
>> 1685
>> 1686 config CPU_R4X00
>> 1687 bool "R4x00"
>> 1688 depends on SYS_HAS_CPU_R4X00
>> 1689 select CPU_SUPPORTS_32BIT_KERNEL
>> 1690 select CPU_SUPPORTS_64BIT_KERNEL
>> 1691 select CPU_SUPPORTS_HUGEPAGES
>> 1692 help
>> 1693 MIPS Technologies R4000-series processors other than 4300, including
>> 1694 the R4000, R4400, R4600, and 4700.
>> 1695
>> 1696 config CPU_TX49XX
>> 1697 bool "R49XX"
>> 1698 depends on SYS_HAS_CPU_TX49XX
>> 1699 select CPU_HAS_PREFETCH
>> 1700 select CPU_SUPPORTS_32BIT_KERNEL
>> 1701 select CPU_SUPPORTS_64BIT_KERNEL
>> 1702 select CPU_SUPPORTS_HUGEPAGES
>> 1703
>> 1704 config CPU_R5000
>> 1705 bool "R5000"
>> 1706 depends on SYS_HAS_CPU_R5000
>> 1707 select CPU_SUPPORTS_32BIT_KERNEL
>> 1708 select CPU_SUPPORTS_64BIT_KERNEL
>> 1709 select CPU_SUPPORTS_HUGEPAGES
>> 1710 help
>> 1711 MIPS Technologies R5000-series processors other than the Nevada.
>> 1712
>> 1713 config CPU_R5500
>> 1714 bool "R5500"
>> 1715 depends on SYS_HAS_CPU_R5500
>> 1716 select CPU_SUPPORTS_32BIT_KERNEL
>> 1717 select CPU_SUPPORTS_64BIT_KERNEL
>> 1718 select CPU_SUPPORTS_HUGEPAGES
>> 1719 help
>> 1720 NEC VR5500 and VR5500A series processors implement 64-bit MIPS IV
>> 1721 instruction set.
>> 1722
>> 1723 config CPU_NEVADA
>> 1724 bool "RM52xx"
>> 1725 depends on SYS_HAS_CPU_NEVADA
>> 1726 select CPU_SUPPORTS_32BIT_KERNEL
>> 1727 select CPU_SUPPORTS_64BIT_KERNEL
>> 1728 select CPU_SUPPORTS_HUGEPAGES
>> 1729 help
>> 1730 QED / PMC-Sierra RM52xx-series ("Nevada") processors.
>> 1731
>> 1732 config CPU_R10000
>> 1733 bool "R10000"
>> 1734 depends on SYS_HAS_CPU_R10000
>> 1735 select CPU_HAS_PREFETCH
>> 1736 select CPU_SUPPORTS_32BIT_KERNEL
>> 1737 select CPU_SUPPORTS_64BIT_KERNEL
>> 1738 select CPU_SUPPORTS_HIGHMEM
>> 1739 select CPU_SUPPORTS_HUGEPAGES
>> 1740 help
>> 1741 MIPS Technologies R10000-series processors.
>> 1742
>> 1743 config CPU_RM7000
>> 1744 bool "RM7000"
>> 1745 depends on SYS_HAS_CPU_RM7000
>> 1746 select CPU_HAS_PREFETCH
>> 1747 select CPU_SUPPORTS_32BIT_KERNEL
>> 1748 select CPU_SUPPORTS_64BIT_KERNEL
>> 1749 select CPU_SUPPORTS_HIGHMEM
>> 1750 select CPU_SUPPORTS_HUGEPAGES
>> 1751
>> 1752 config CPU_SB1
>> 1753 bool "SB1"
>> 1754 depends on SYS_HAS_CPU_SB1
>> 1755 select CPU_SUPPORTS_32BIT_KERNEL
>> 1756 select CPU_SUPPORTS_64BIT_KERNEL
>> 1757 select CPU_SUPPORTS_HIGHMEM
>> 1758 select CPU_SUPPORTS_HUGEPAGES
>> 1759 select WEAK_ORDERING
>> 1760
>> 1761 config CPU_CAVIUM_OCTEON
>> 1762 bool "Cavium Octeon processor"
>> 1763 depends on SYS_HAS_CPU_CAVIUM_OCTEON
>> 1764 select CPU_HAS_PREFETCH
>> 1765 select CPU_SUPPORTS_64BIT_KERNEL
>> 1766 select WEAK_ORDERING
>> 1767 select CPU_SUPPORTS_HIGHMEM
>> 1768 select CPU_SUPPORTS_HUGEPAGES
>> 1769 select USB_EHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
>> 1770 select USB_OHCI_BIG_ENDIAN_MMIO if CPU_BIG_ENDIAN
>> 1771 select MIPS_L1_CACHE_SHIFT_7
>> 1772 select HAVE_KVM
>> 1773 help
>> 1774 The Cavium Octeon processor is a highly integrated chip containing
>> 1775 many ethernet hardware widgets for networking tasks. The processor
>> 1776 can have up to 16 Mips64v2 cores and 8 integrated gigabit ethernets.
>> 1777 Full details can be found at http://www.caviumnetworks.com.
>> 1778
>> 1779 config CPU_BMIPS
>> 1780 bool "Broadcom BMIPS"
>> 1781 depends on SYS_HAS_CPU_BMIPS
>> 1782 select CPU_MIPS32
>> 1783 select CPU_BMIPS32_3300 if SYS_HAS_CPU_BMIPS32_3300
>> 1784 select CPU_BMIPS4350 if SYS_HAS_CPU_BMIPS4350
>> 1785 select CPU_BMIPS4380 if SYS_HAS_CPU_BMIPS4380
>> 1786 select CPU_BMIPS5000 if SYS_HAS_CPU_BMIPS5000
>> 1787 select CPU_SUPPORTS_32BIT_KERNEL
>> 1788 select DMA_NONCOHERENT
>> 1789 select IRQ_MIPS_CPU
>> 1790 select SWAP_IO_SPACE
>> 1791 select WEAK_ORDERING
>> 1792 select CPU_SUPPORTS_HIGHMEM
>> 1793 select CPU_HAS_PREFETCH
>> 1794 select CPU_SUPPORTS_CPUFREQ
>> 1795 select MIPS_EXTERNAL_TIMER
>> 1796 help
>> 1797 Support for BMIPS32/3300/4350/4380 and BMIPS5000 processors.
>> 1798
>> 1799 config CPU_XLR
>> 1800 bool "Netlogic XLR SoC"
>> 1801 depends on SYS_HAS_CPU_XLR
>> 1802 select CPU_SUPPORTS_32BIT_KERNEL
>> 1803 select CPU_SUPPORTS_64BIT_KERNEL
>> 1804 select CPU_SUPPORTS_HIGHMEM
>> 1805 select CPU_SUPPORTS_HUGEPAGES
>> 1806 select WEAK_ORDERING
>> 1807 select WEAK_REORDERING_BEYOND_LLSC
>> 1808 help
>> 1809 Netlogic Microsystems XLR/XLS processors.
>> 1810
>> 1811 config CPU_XLP
>> 1812 bool "Netlogic XLP SoC"
>> 1813 depends on SYS_HAS_CPU_XLP
>> 1814 select CPU_SUPPORTS_32BIT_KERNEL
>> 1815 select CPU_SUPPORTS_64BIT_KERNEL
>> 1816 select CPU_SUPPORTS_HIGHMEM
>> 1817 select WEAK_ORDERING
>> 1818 select WEAK_REORDERING_BEYOND_LLSC
>> 1819 select CPU_HAS_PREFETCH
>> 1820 select CPU_MIPSR2
>> 1821 select CPU_SUPPORTS_HUGEPAGES
>> 1822 select MIPS_ASID_BITS_VARIABLE
>> 1823 help
>> 1824 Netlogic Microsystems XLP processors.
>> 1825 endchoice
>> 1826
>> 1827 config CPU_MIPS32_3_5_FEATURES
>> 1828 bool "MIPS32 Release 3.5 Features"
>> 1829 depends on SYS_HAS_CPU_MIPS32_R3_5
>> 1830 depends on CPU_MIPS32_R2 || CPU_MIPS32_R6
>> 1831 help
>> 1832 Choose this option to build a kernel for release 2 or later of the
>> 1833 MIPS32 architecture including features from the 3.5 release such as
>> 1834 support for Enhanced Virtual Addressing (EVA).
>> 1835
>> 1836 config CPU_MIPS32_3_5_EVA
>> 1837 bool "Enhanced Virtual Addressing (EVA)"
>> 1838 depends on CPU_MIPS32_3_5_FEATURES
>> 1839 select EVA
>> 1840 default y
>> 1841 help
>> 1842 Choose this option if you want to enable the Enhanced Virtual
>> 1843 Addressing (EVA) on your MIPS32 core (such as proAptiv).
>> 1844 One of its primary benefits is an increase in the maximum size
>> 1845 of lowmem (up to 3GB). If unsure, say 'N' here.
>> 1846
>> 1847 config CPU_MIPS32_R5_FEATURES
>> 1848 bool "MIPS32 Release 5 Features"
>> 1849 depends on SYS_HAS_CPU_MIPS32_R5
>> 1850 depends on CPU_MIPS32_R2
>> 1851 help
>> 1852 Choose this option to build a kernel for release 2 or later of the
>> 1853 MIPS32 architecture including features from release 5 such as
>> 1854 support for Extended Physical Addressing (XPA).
>> 1855
>> 1856 config CPU_MIPS32_R5_XPA
>> 1857 bool "Extended Physical Addressing (XPA)"
>> 1858 depends on CPU_MIPS32_R5_FEATURES
>> 1859 depends on !EVA
>> 1860 depends on !PAGE_SIZE_4KB
>> 1861 depends on SYS_SUPPORTS_HIGHMEM
>> 1862 select XPA
>> 1863 select HIGHMEM
>> 1864 select PHYS_ADDR_T_64BIT
>> 1865 default n
>> 1866 help
>> 1867 Choose this option if you want to enable the Extended Physical
>> 1868 Addressing (XPA) on your MIPS32 core (such as P5600 series). The
>> 1869 benefit is to increase physical addressing equal to or greater
>> 1870 than 40 bits. Note that this has the side effect of turning on
>> 1871 64-bit addressing which in turn makes the PTEs 64-bit in size.
>> 1872 If unsure, say 'N' here.
>> 1873
>> 1874 if CPU_LOONGSON2F
>> 1875 config CPU_NOP_WORKAROUNDS
>> 1876 bool
>> 1877
>> 1878 config CPU_JUMP_WORKAROUNDS
>> 1879 bool
>> 1880
>> 1881 config CPU_LOONGSON2F_WORKAROUNDS
>> 1882 bool "Loongson 2F Workarounds"
>> 1883 default y
>> 1884 select CPU_NOP_WORKAROUNDS
>> 1885 select CPU_JUMP_WORKAROUNDS
>> 1886 help
>> 1887 Loongson 2F01 / 2F02 processors have the NOP & JUMP issues which
>> 1888 require workarounds. Without workarounds the system may hang
>> 1889 unexpectedly. For more information please refer to the gas
>> 1890 -mfix-loongson2f-nop and -mfix-loongson2f-jump options.
>> 1891
>> 1892 Loongson 2F03 and later have fixed these issues and no workarounds
>> 1893 are needed. The workarounds have no significant side effect on them
>> 1894 but may decrease the performance of the system so this option should
>> 1895 be disabled unless the kernel is intended to be run on 2F01 or 2F02
>> 1896 systems.
>> 1897
>> 1898 If unsure, please say Y.
>> 1899 endif # CPU_LOONGSON2F
>> 1900
>> 1901 config SYS_SUPPORTS_ZBOOT
>> 1902 bool
>> 1903 select HAVE_KERNEL_GZIP
>> 1904 select HAVE_KERNEL_BZIP2
>> 1905 select HAVE_KERNEL_LZ4
>> 1906 select HAVE_KERNEL_LZMA
>> 1907 select HAVE_KERNEL_LZO
>> 1908 select HAVE_KERNEL_XZ
>> 1909
>> 1910 config SYS_SUPPORTS_ZBOOT_UART16550
>> 1911 bool
>> 1912 select SYS_SUPPORTS_ZBOOT
>> 1913
>> 1914 config SYS_SUPPORTS_ZBOOT_UART_PROM
>> 1915 bool
>> 1916 select SYS_SUPPORTS_ZBOOT
>> 1917
>> 1918 config CPU_LOONGSON2EF
>> 1919 bool
>> 1920 select CPU_SUPPORTS_32BIT_KERNEL
>> 1921 select CPU_SUPPORTS_64BIT_KERNEL
>> 1922 select CPU_SUPPORTS_HIGHMEM
>> 1923 select CPU_SUPPORTS_HUGEPAGES
>> 1924 select ARCH_HAS_PHYS_TO_DMA
>> 1925
>> 1926 config CPU_LOONGSON32
>> 1927 bool
>> 1928 select CPU_MIPS32
>> 1929 select CPU_MIPSR2
>> 1930 select CPU_HAS_PREFETCH
>> 1931 select CPU_SUPPORTS_32BIT_KERNEL
>> 1932 select CPU_SUPPORTS_HIGHMEM
>> 1933 select CPU_SUPPORTS_CPUFREQ
>> 1934
>> 1935 config CPU_BMIPS32_3300
>> 1936 select SMP_UP if SMP
>> 1937 bool
>> 1938
>> 1939 config CPU_BMIPS4350
>> 1940 bool
>> 1941 select SYS_SUPPORTS_SMP
>> 1942 select SYS_SUPPORTS_HOTPLUG_CPU
>> 1943
>> 1944 config CPU_BMIPS4380
>> 1945 bool
>> 1946 select MIPS_L1_CACHE_SHIFT_6
>> 1947 select SYS_SUPPORTS_SMP
>> 1948 select SYS_SUPPORTS_HOTPLUG_CPU
>> 1949 select CPU_HAS_RIXI
>> 1950
>> 1951 config CPU_BMIPS5000
>> 1952 bool
>> 1953 select MIPS_CPU_SCACHE
>> 1954 select MIPS_L1_CACHE_SHIFT_7
>> 1955 select SYS_SUPPORTS_SMP
>> 1956 select SYS_SUPPORTS_HOTPLUG_CPU
>> 1957 select CPU_HAS_RIXI
>> 1958
>> 1959 config SYS_HAS_CPU_LOONGSON64
>> 1960 bool
>> 1961 select CPU_SUPPORTS_CPUFREQ
>> 1962 select CPU_HAS_RIXI
>> 1963
>> 1964 config SYS_HAS_CPU_LOONGSON2E
>> 1965 bool
>> 1966
>> 1967 config SYS_HAS_CPU_LOONGSON2F
>> 1968 bool
>> 1969 select CPU_SUPPORTS_CPUFREQ
>> 1970 select CPU_SUPPORTS_ADDRWINCFG if 64BIT
>> 1971
>> 1972 config SYS_HAS_CPU_LOONGSON1B
>> 1973 bool
>> 1974
>> 1975 config SYS_HAS_CPU_LOONGSON1C
>> 1976 bool
>> 1977
>> 1978 config SYS_HAS_CPU_MIPS32_R1
>> 1979 bool
>> 1980
>> 1981 config SYS_HAS_CPU_MIPS32_R2
>> 1982 bool
>> 1983
>> 1984 config SYS_HAS_CPU_MIPS32_R3_5
>> 1985 bool
>> 1986
>> 1987 config SYS_HAS_CPU_MIPS32_R5
>> 1988 bool
>> 1989 select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
>> 1990
>> 1991 config SYS_HAS_CPU_MIPS32_R6
>> 1992 bool
>> 1993 select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
>> 1994
>> 1995 config SYS_HAS_CPU_MIPS64_R1
>> 1996 bool
>> 1997
>> 1998 config SYS_HAS_CPU_MIPS64_R2
>> 1999 bool
>> 2000
>> 2001 config SYS_HAS_CPU_MIPS64_R6
>> 2002 bool
>> 2003 select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
>> 2004
>> 2005 config SYS_HAS_CPU_R3000
>> 2006 bool
>> 2007
>> 2008 config SYS_HAS_CPU_TX39XX
>> 2009 bool
>> 2010
>> 2011 config SYS_HAS_CPU_VR41XX
>> 2012 bool
>> 2013
>> 2014 config SYS_HAS_CPU_R4X00
>> 2015 bool
>> 2016
>> 2017 config SYS_HAS_CPU_TX49XX
>> 2018 bool
>> 2019
>> 2020 config SYS_HAS_CPU_R5000
>> 2021 bool
>> 2022
>> 2023 config SYS_HAS_CPU_R5500
>> 2024 bool
>> 2025
>> 2026 config SYS_HAS_CPU_NEVADA
>> 2027 bool
>> 2028
>> 2029 config SYS_HAS_CPU_R10000
>> 2030 bool
>> 2031 select ARCH_HAS_SYNC_DMA_FOR_CPU if DMA_NONCOHERENT
>> 2032
>> 2033 config SYS_HAS_CPU_RM7000
>> 2034 bool
>> 2035
>> 2036 config SYS_HAS_CPU_SB1
>> 2037 bool
>> 2038
>> 2039 config SYS_HAS_CPU_CAVIUM_OCTEON
>> 2040 bool
>> 2041
>> 2042 config SYS_HAS_CPU_BMIPS
>> 2043 bool
>> 2044
>> 2045 config SYS_HAS_CPU_BMIPS32_3300
>> 2046 bool
>> 2047 select SYS_HAS_CPU_BMIPS
>> 2048
>> 2049 config SYS_HAS_CPU_BMIPS4350
>> 2050 bool
>> 2051 select SYS_HAS_CPU_BMIPS
>> 2052
>> 2053 config SYS_HAS_CPU_BMIPS4380
>> 2054 bool
>> 2055 select SYS_HAS_CPU_BMIPS
>> 2056
>> 2057 config SYS_HAS_CPU_BMIPS5000
>> 2058 bool
>> 2059 select SYS_HAS_CPU_BMIPS
>> 2060 select ARCH_HAS_SYNC_DMA_FOR_CPU
>> 2061
>> 2062 config SYS_HAS_CPU_XLR
>> 2063 bool
>> 2064
>> 2065 config SYS_HAS_CPU_XLP
>> 2066 bool
>> 2067
>> 2068 #
>> 2069 # CPU may reorder R->R, R->W, W->R, W->W
>> 2070 # Reordering beyond LL and SC is handled in WEAK_REORDERING_BEYOND_LLSC
>> 2071 #
>> 2072 config WEAK_ORDERING
>> 2073 bool
>> 2074
>> 2075 #
>> 2076 # CPU may reorder reads and writes beyond LL/SC
>> 2077 # CPU may reorder R->LL, R->LL, W->LL, W->LL, R->SC, R->SC, W->SC, W->SC
>> 2078 #
>> 2079 config WEAK_REORDERING_BEYOND_LLSC
>> 2080 bool
>> 2081 endmenu
>> 2082
>> 2083 #
>> 2084 # These two indicate any level of the MIPS32 and MIPS64 architecture
>> 2085 #
>> 2086 config CPU_MIPS32
>> 2087 bool
>> 2088 default y if CPU_MIPS32_R1 || CPU_MIPS32_R2 || CPU_MIPS32_R6
>> 2089
>> 2090 config CPU_MIPS64
>> 2091 bool
>> 2092 default y if CPU_MIPS64_R1 || CPU_MIPS64_R2 || CPU_MIPS64_R6
>> 2093
>> 2094 #
>> 2095 # These indicate the revision of the architecture
>> 2096 #
>> 2097 config CPU_MIPSR1
>> 2098 bool
>> 2099 default y if CPU_MIPS32_R1 || CPU_MIPS64_R1
>> 2100
>> 2101 config CPU_MIPSR2
>> 2102 bool
>> 2103 default y if CPU_MIPS32_R2 || CPU_MIPS64_R2 || CPU_CAVIUM_OCTEON
>> 2104 select CPU_HAS_RIXI
>> 2105 select CPU_HAS_DIEI if !CPU_DIEI_BROKEN
>> 2106 select MIPS_SPRAM
>> 2107
>> 2108 config CPU_MIPSR6
>> 2109 bool
>> 2110 default y if CPU_MIPS32_R6 || CPU_MIPS64_R6
>> 2111 select CPU_HAS_RIXI
>> 2112 select CPU_HAS_DIEI if !CPU_DIEI_BROKEN
>> 2113 select HAVE_ARCH_BITREVERSE
>> 2114 select MIPS_ASID_BITS_VARIABLE
>> 2115 select MIPS_CRC_SUPPORT
>> 2116 select MIPS_SPRAM
>> 2117
>> 2118 config TARGET_ISA_REV
>> 2119 int
>> 2120 default 1 if CPU_MIPSR1
>> 2121 default 2 if CPU_MIPSR2
>> 2122 default 6 if CPU_MIPSR6
>> 2123 default 0
>> 2124 help
>> 2125 Reflects the ISA revision being targeted by the kernel build. This
>> 2126 is effectively the Kconfig equivalent of MIPS_ISA_REV.
>> 2127
>> 2128 config EVA
>> 2129 bool
>> 2130
>> 2131 config XPA
>> 2132 bool
>> 2133
>> 2134 config SYS_SUPPORTS_32BIT_KERNEL
>> 2135 bool
>> 2136 config SYS_SUPPORTS_64BIT_KERNEL
>> 2137 bool
>> 2138 config CPU_SUPPORTS_32BIT_KERNEL
>> 2139 bool
>> 2140 config CPU_SUPPORTS_64BIT_KERNEL
>> 2141 bool
>> 2142 config CPU_SUPPORTS_CPUFREQ
>> 2143 bool
>> 2144 config CPU_SUPPORTS_ADDRWINCFG
>> 2145 bool
>> 2146 config CPU_SUPPORTS_HUGEPAGES
>> 2147 bool
>> 2148 depends on !(32BIT && (ARCH_PHYS_ADDR_T_64BIT || EVA))
>> 2149 config MIPS_PGD_C0_CONTEXT
>> 2150 bool
>> 2151 default y if 64BIT && (CPU_MIPSR2 || CPU_MIPSR6) && !CPU_XLP
>> 2152
>> 2153 #
>> 2154 # Set to y for ptrace access to watch registers.
>> 2155 #
>> 2156 config HARDWARE_WATCHPOINTS
>> 2157 bool
>> 2158 default y if CPU_MIPSR1 || CPU_MIPSR2 || CPU_MIPSR6
>> 2159
>> 2160 menu "Kernel type"
>> 2161
>> 2162 choice
>> 2163 prompt "Kernel code model"
>> 2164 help
>> 2165 You should only select this option if you have a workload that
>> 2166 actually benefits from 64-bit processing or if your machine has
>> 2167 large memory. You will only be presented a single option in this
>> 2168 menu if your system does not support both 32-bit and 64-bit kernels.
>> 2169
>> 2170 config 32BIT
>> 2171 bool "32-bit kernel"
>> 2172 depends on CPU_SUPPORTS_32BIT_KERNEL && SYS_SUPPORTS_32BIT_KERNEL
>> 2173 select TRAD_SIGNALS
>> 2174 help
>> 2175 Select this option if you want to build a 32-bit kernel.
>> 2176
>> 2177 config 64BIT
>> 2178 bool "64-bit kernel"
>> 2179 depends on CPU_SUPPORTS_64BIT_KERNEL && SYS_SUPPORTS_64BIT_KERNEL
>> 2180 help
>> 2181 Select this option if you want to build a 64-bit kernel.
>> 2182
>> 2183 endchoice
>> 2184
>> 2185 config KVM_GUEST
>> 2186 bool "KVM Guest Kernel"
>> 2187 depends on BROKEN_ON_SMP
>> 2188 help
>> 2189 Select this option if building a guest kernel for KVM (Trap & Emulate)
>> 2190 mode.
>> 2191
>> 2192 config KVM_GUEST_TIMER_FREQ
>> 2193 int "Count/Compare Timer Frequency (MHz)"
>> 2194 depends on KVM_GUEST
>> 2195 default 100
>> 2196 help
>> 2197 Set this to non-zero if building a guest kernel for KVM to skip RTC
>> 2198 emulation when determining guest CPU Frequency. Instead, the guest's
>> 2199 timer frequency is specified directly.
>> 2200
>> 2201 config MIPS_VA_BITS_48
>> 2202 bool "48 bits virtual memory"
>> 2203 depends on 64BIT
>> 2204 help
>> 2205 Support a maximum at least 48 bits of application virtual
>> 2206 memory. Default is 40 bits or less, depending on the CPU.
>> 2207 For page sizes 16k and above, this option results in a small
>> 2208 memory overhead for page tables. For 4k page size, a fourth
>> 2209 level of page tables is added which imposes both a memory
>> 2210 overhead as well as slower TLB fault handling.
>> 2211
>> 2212 If unsure, say N.
>> 2213
>> 2214 choice
>> 2215 prompt "Kernel page size"
>> 2216 default PAGE_SIZE_4KB
>> 2217
>> 2218 config PAGE_SIZE_4KB
>> 2219 bool "4kB"
>> 2220 depends on !CPU_LOONGSON2EF && !CPU_LOONGSON64
>> 2221 help
>> 2222 This option select the standard 4kB Linux page size. On some
>> 2223 R3000-family processors this is the only available page size. Using
>> 2224 4kB page size will minimize memory consumption and is therefore
>> 2225 recommended for low memory systems.
>> 2226
>> 2227 config PAGE_SIZE_8KB
>> 2228 bool "8kB"
>> 2229 depends on CPU_CAVIUM_OCTEON
>> 2230 depends on !MIPS_VA_BITS_48
>> 2231 help
>> 2232 Using 8kB page size will result in higher performance kernel at
>> 2233 the price of higher memory consumption. This option is available
>> 2234 only on cnMIPS processors. Note that you will need a suitable Linux
>> 2235 distribution to support this.
>> 2236
>> 2237 config PAGE_SIZE_16KB
>> 2238 bool "16kB"
>> 2239 depends on !CPU_R3000 && !CPU_TX39XX
>> 2240 help
>> 2241 Using 16kB page size will result in higher performance kernel at
>> 2242 the price of higher memory consumption. This option is available on
>> 2243 all non-R3000 family processors. Note that you will need a suitable
>> 2244 Linux distribution to support this.
>> 2245
>> 2246 config PAGE_SIZE_32KB
>> 2247 bool "32kB"
>> 2248 depends on CPU_CAVIUM_OCTEON
>> 2249 depends on !MIPS_VA_BITS_48
>> 2250 help
>> 2251 Using 32kB page size will result in higher performance kernel at
>> 2252 the price of higher memory consumption. This option is available
>> 2253 only on cnMIPS cores. Note that you will need a suitable Linux
>> 2254 distribution to support this.
>> 2255
>> 2256 config PAGE_SIZE_64KB
>> 2257 bool "64kB"
>> 2258 depends on !CPU_R3000 && !CPU_TX39XX
>> 2259 help
>> 2260 Using 64kB page size will result in higher performance kernel at
>> 2261 the price of higher memory consumption. This option is available on
>> 2262 all non-R3000 family processor. Not that at the time of this
>> 2263 writing this option is still high experimental.
>> 2264
>> 2265 endchoice
>> 2266
>> 2267 config FORCE_MAX_ZONEORDER
>> 2268 int "Maximum zone order"
>> 2269 range 14 64 if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_64KB
>> 2270 default "14" if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_64KB
>> 2271 range 13 64 if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_32KB
>> 2272 default "13" if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_32KB
>> 2273 range 12 64 if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_16KB
>> 2274 default "12" if MIPS_HUGE_TLB_SUPPORT && PAGE_SIZE_16KB
>> 2275 range 11 64
>> 2276 default "11"
>> 2277 help
>> 2278 The kernel memory allocator divides physically contiguous memory
>> 2279 blocks into "zones", where each zone is a power of two number of
>> 2280 pages. This option selects the largest power of two that the kernel
>> 2281 keeps in the memory allocator. If you need to allocate very large
>> 2282 blocks of physically contiguous memory, then you may need to
>> 2283 increase this value.
>> 2284
>> 2285 This config option is actually maximum order plus one. For example,
>> 2286 a value of 11 means that the largest free memory block is 2^10 pages.
>> 2287
>> 2288 The page size is not necessarily 4KB. Keep this in mind
>> 2289 when choosing a value for this option.
>> 2290
>> 2291 config BOARD_SCACHE
>> 2292 bool
>> 2293
>> 2294 config IP22_CPU_SCACHE
>> 2295 bool
>> 2296 select BOARD_SCACHE
>> 2297
>> 2298 #
>> 2299 # Support for a MIPS32 / MIPS64 style S-caches
>> 2300 #
>> 2301 config MIPS_CPU_SCACHE
>> 2302 bool
>> 2303 select BOARD_SCACHE
>> 2304
>> 2305 config R5000_CPU_SCACHE
>> 2306 bool
>> 2307 select BOARD_SCACHE
>> 2308
>> 2309 config RM7000_CPU_SCACHE
>> 2310 bool
>> 2311 select BOARD_SCACHE
>> 2312
>> 2313 config SIBYTE_DMA_PAGEOPS
>> 2314 bool "Use DMA to clear/copy pages"
>> 2315 depends on CPU_SB1
>> 2316 help
>> 2317 Instead of using the CPU to zero and copy pages, use a Data Mover
>> 2318 channel. These DMA channels are otherwise unused by the standard
>> 2319 SiByte Linux port. Seems to give a small performance benefit.
>> 2320
>> 2321 config CPU_HAS_PREFETCH
>> 2322 bool
>> 2323
>> 2324 config CPU_GENERIC_DUMP_TLB
>> 2325 bool
>> 2326 default y if !(CPU_R3000 || CPU_TX39XX)
>> 2327
>> 2328 config MIPS_FP_SUPPORT
>> 2329 bool "Floating Point support" if EXPERT
>> 2330 default y
>> 2331 help
>> 2332 Select y to include support for floating point in the kernel
>> 2333 including initialization of FPU hardware, FP context save & restore
>> 2334 and emulation of an FPU where necessary. Without this support any
>> 2335 userland program attempting to use floating point instructions will
>> 2336 receive a SIGILL.
>> 2337
>> 2338 If you know that your userland will not attempt to use floating point
>> 2339 instructions then you can say n here to shrink the kernel a little.
>> 2340
>> 2341 If unsure, say y.
>> 2342
>> 2343 config CPU_R2300_FPU
>> 2344 bool
>> 2345 depends on MIPS_FP_SUPPORT
>> 2346 default y if CPU_R3000 || CPU_TX39XX
>> 2347
>> 2348 config CPU_R3K_TLB
>> 2349 bool
>> 2350
>> 2351 config CPU_R4K_FPU
>> 2352 bool
>> 2353 depends on MIPS_FP_SUPPORT
>> 2354 default y if !CPU_R2300_FPU
>> 2355
>> 2356 config CPU_R4K_CACHE_TLB
>> 2357 bool
>> 2358 default y if !(CPU_R3K_TLB || CPU_SB1 || CPU_CAVIUM_OCTEON)
>> 2359
>> 2360 config MIPS_MT_SMP
>> 2361 bool "MIPS MT SMP support (1 TC on each available VPE)"
>> 2362 default y
>> 2363 depends on SYS_SUPPORTS_MULTITHREADING && !CPU_MIPSR6 && !CPU_MICROMIPS
>> 2364 select CPU_MIPSR2_IRQ_VI
>> 2365 select CPU_MIPSR2_IRQ_EI
>> 2366 select SYNC_R4K
>> 2367 select MIPS_MT
>> 2368 select SMP
>> 2369 select SMP_UP
>> 2370 select SYS_SUPPORTS_SMP
>> 2371 select SYS_SUPPORTS_SCHED_SMT
>> 2372 select MIPS_PERF_SHARED_TC_COUNTERS
>> 2373 help
>> 2374 This is a kernel model which is known as SMVP. This is supported
>> 2375 on cores with the MT ASE and uses the available VPEs to implement
>> 2376 virtual processors which supports SMP. This is equivalent to the
>> 2377 Intel Hyperthreading feature. For further information go to
>> 2378 <http://www.imgtec.com/mips/mips-multithreading.asp>.
>> 2379
>> 2380 config MIPS_MT
>> 2381 bool
>> 2382
>> 2383 config SCHED_SMT
>> 2384 bool "SMT (multithreading) scheduler support"
>> 2385 depends on SYS_SUPPORTS_SCHED_SMT
>> 2386 default n
>> 2387 help
>> 2388 SMT scheduler support improves the CPU scheduler's decision making
>> 2389 when dealing with MIPS MT enabled cores at a cost of slightly
>> 2390 increased overhead in some places. If unsure say N here.
>> 2391
>> 2392 config SYS_SUPPORTS_SCHED_SMT
>> 2393 bool
>> 2394
>> 2395 config SYS_SUPPORTS_MULTITHREADING
>> 2396 bool
>> 2397
>> 2398 config MIPS_MT_FPAFF
>> 2399 bool "Dynamic FPU affinity for FP-intensive threads"
>> 2400 default y
>> 2401 depends on MIPS_MT_SMP
>> 2402
>> 2403 config MIPSR2_TO_R6_EMULATOR
>> 2404 bool "MIPS R2-to-R6 emulator"
>> 2405 depends on CPU_MIPSR6
>> 2406 depends on MIPS_FP_SUPPORT
>> 2407 default y
>> 2408 help
>> 2409 Choose this option if you want to run non-R6 MIPS userland code.
>> 2410 Even if you say 'Y' here, the emulator will still be disabled by
>> 2411 default. You can enable it using the 'mipsr2emu' kernel option.
>> 2412 The only reason this is a build-time option is to save ~14K from the
>> 2413 final kernel image.
>> 2414
>> 2415 config SYS_SUPPORTS_VPE_LOADER
>> 2416 bool
>> 2417 depends on SYS_SUPPORTS_MULTITHREADING
>> 2418 help
>> 2419 Indicates that the platform supports the VPE loader, and provides
>> 2420 physical_memsize.
>> 2421
>> 2422 config MIPS_VPE_LOADER
>> 2423 bool "VPE loader support."
>> 2424 depends on SYS_SUPPORTS_VPE_LOADER && MODULES
>> 2425 select CPU_MIPSR2_IRQ_VI
>> 2426 select CPU_MIPSR2_IRQ_EI
>> 2427 select MIPS_MT
>> 2428 help
>> 2429 Includes a loader for loading an elf relocatable object
>> 2430 onto another VPE and running it.
>> 2431
>> 2432 config MIPS_VPE_LOADER_CMP
>> 2433 bool
>> 2434 default "y"
>> 2435 depends on MIPS_VPE_LOADER && MIPS_CMP
>> 2436
>> 2437 config MIPS_VPE_LOADER_MT
>> 2438 bool
>> 2439 default "y"
>> 2440 depends on MIPS_VPE_LOADER && !MIPS_CMP
>> 2441
>> 2442 config MIPS_VPE_LOADER_TOM
>> 2443 bool "Load VPE program into memory hidden from linux"
>> 2444 depends on MIPS_VPE_LOADER
>> 2445 default y
>> 2446 help
>> 2447 The loader can use memory that is present but has been hidden from
>> 2448 Linux using the kernel command line option "mem=xxMB". It's up to
>> 2449 you to ensure the amount you put in the option and the space your
>> 2450 program requires is less or equal to the amount physically present.
>> 2451
>> 2452 config MIPS_VPE_APSP_API
>> 2453 bool "Enable support for AP/SP API (RTLX)"
>> 2454 depends on MIPS_VPE_LOADER
>> 2455
>> 2456 config MIPS_VPE_APSP_API_CMP
>> 2457 bool
>> 2458 default "y"
>> 2459 depends on MIPS_VPE_APSP_API && MIPS_CMP
>> 2460
>> 2461 config MIPS_VPE_APSP_API_MT
>> 2462 bool
>> 2463 default "y"
>> 2464 depends on MIPS_VPE_APSP_API && !MIPS_CMP
>> 2465
>> 2466 config MIPS_CMP
>> 2467 bool "MIPS CMP framework support (DEPRECATED)"
>> 2468 depends on SYS_SUPPORTS_MIPS_CMP && !CPU_MIPSR6
>> 2469 select SMP
>> 2470 select SYNC_R4K
>> 2471 select SYS_SUPPORTS_SMP
>> 2472 select WEAK_ORDERING
>> 2473 default n
>> 2474 help
>> 2475 Select this if you are using a bootloader which implements the "CMP
>> 2476 framework" protocol (ie. YAMON) and want your kernel to make use of
>> 2477 its ability to start secondary CPUs.
>> 2478
>> 2479 Unless you have a specific need, you should use CONFIG_MIPS_CPS
>> 2480 instead of this.
>> 2481
>> 2482 config MIPS_CPS
>> 2483 bool "MIPS Coherent Processing System support"
>> 2484 depends on SYS_SUPPORTS_MIPS_CPS
>> 2485 select MIPS_CM
>> 2486 select MIPS_CPS_PM if HOTPLUG_CPU
>> 2487 select SMP
>> 2488 select SYNC_R4K if (CEVT_R4K || CSRC_R4K)
>> 2489 select SYS_SUPPORTS_HOTPLUG_CPU
>> 2490 select SYS_SUPPORTS_SCHED_SMT if CPU_MIPSR6
>> 2491 select SYS_SUPPORTS_SMP
>> 2492 select WEAK_ORDERING
>> 2493 help
>> 2494 Select this if you wish to run an SMP kernel across multiple cores
>> 2495 within a MIPS Coherent Processing System. When this option is
>> 2496 enabled the kernel will probe for other cores and boot them with
>> 2497 no external assistance. It is safe to enable this when hardware
>> 2498 support is unavailable.
>> 2499
>> 2500 config MIPS_CPS_PM
>> 2501 depends on MIPS_CPS
>> 2502 bool
>> 2503
>> 2504 config MIPS_CM
>> 2505 bool
>> 2506 select MIPS_CPC
>> 2507
>> 2508 config MIPS_CPC
>> 2509 bool
>> 2510
>> 2511 config SB1_PASS_2_WORKAROUNDS
>> 2512 bool
>> 2513 depends on CPU_SB1 && (CPU_SB1_PASS_2_2 || CPU_SB1_PASS_2)
>> 2514 default y
>> 2515
>> 2516 config SB1_PASS_2_1_WORKAROUNDS
>> 2517 bool
>> 2518 depends on CPU_SB1 && CPU_SB1_PASS_2
>> 2519 default y
>> 2520
>> 2521 choice
>> 2522 prompt "SmartMIPS or microMIPS ASE support"
>> 2523
>> 2524 config CPU_NEEDS_NO_SMARTMIPS_OR_MICROMIPS
>> 2525 bool "None"
>> 2526 help
>> 2527 Select this if you want neither microMIPS nor SmartMIPS support
>> 2528
>> 2529 config CPU_HAS_SMARTMIPS
>> 2530 depends on SYS_SUPPORTS_SMARTMIPS
>> 2531 bool "SmartMIPS"
>> 2532 help
>> 2533 SmartMIPS is a extension of the MIPS32 architecture aimed at
>> 2534 increased security at both hardware and software level for
>> 2535 smartcards. Enabling this option will allow proper use of the
>> 2536 SmartMIPS instructions by Linux applications. However a kernel with
>> 2537 this option will not work on a MIPS core without SmartMIPS core. If
>> 2538 you don't know you probably don't have SmartMIPS and should say N
>> 2539 here.
>> 2540
>> 2541 config CPU_MICROMIPS
>> 2542 depends on 32BIT && SYS_SUPPORTS_MICROMIPS && !CPU_MIPSR6
>> 2543 bool "microMIPS"
>> 2544 help
>> 2545 When this option is enabled the kernel will be built using the
>> 2546 microMIPS ISA
>> 2547
>> 2548 endchoice
>> 2549
>> 2550 config CPU_HAS_MSA
>> 2551 bool "Support for the MIPS SIMD Architecture"
>> 2552 depends on CPU_SUPPORTS_MSA
>> 2553 depends on MIPS_FP_SUPPORT
>> 2554 depends on 64BIT || MIPS_O32_FP64_SUPPORT
>> 2555 help
>> 2556 MIPS SIMD Architecture (MSA) introduces 128 bit wide vector registers
>> 2557 and a set of SIMD instructions to operate on them. When this option
>> 2558 is enabled the kernel will support allocating & switching MSA
>> 2559 vector register contexts. If you know that your kernel will only be
>> 2560 running on CPUs which do not support MSA or that your userland will
>> 2561 not be making use of it then you may wish to say N here to reduce
>> 2562 the size & complexity of your kernel.
>> 2563
>> 2564 If unsure, say Y.
>> 2565
>> 2566 config CPU_HAS_WB
>> 2567 bool
>> 2568
>> 2569 config XKS01
>> 2570 bool
>> 2571
>> 2572 config CPU_HAS_DIEI
>> 2573 depends on !CPU_DIEI_BROKEN
>> 2574 bool
>> 2575
>> 2576 config CPU_DIEI_BROKEN
>> 2577 bool
>> 2578
>> 2579 config CPU_HAS_RIXI
>> 2580 bool
>> 2581
>> 2582 config CPU_NO_LOAD_STORE_LR
>> 2583 bool
>> 2584 help
>> 2585 CPU lacks support for unaligned load and store instructions:
>> 2586 LWL, LWR, SWL, SWR (Load/store word left/right).
>> 2587 LDL, LDR, SDL, SDR (Load/store doubleword left/right, for 64bit
>> 2588 systems).
>> 2589
>> 2590 #
>> 2591 # Vectored interrupt mode is an R2 feature
>> 2592 #
>> 2593 config CPU_MIPSR2_IRQ_VI
>> 2594 bool
>> 2595
>> 2596 #
>> 2597 # Extended interrupt mode is an R2 feature
>> 2598 #
>> 2599 config CPU_MIPSR2_IRQ_EI
>> 2600 bool
>> 2601
>> 2602 config CPU_HAS_SYNC
>> 2603 bool
>> 2604 depends on !CPU_R3000
>> 2605 default y
>> 2606
>> 2607 #
>> 2608 # CPU non-features
>> 2609 #
>> 2610 config CPU_DADDI_WORKAROUNDS
>> 2611 bool
>> 2612
>> 2613 config CPU_R4000_WORKAROUNDS
>> 2614 bool
>> 2615 select CPU_R4400_WORKAROUNDS
>> 2616
>> 2617 config CPU_R4400_WORKAROUNDS
>> 2618 bool
>> 2619
>> 2620 config CPU_R4X00_BUGS64
>> 2621 bool
>> 2622 default y if SYS_HAS_CPU_R4X00 && 64BIT && (TARGET_ISA_REV < 1)
>> 2623
>> 2624 config MIPS_ASID_SHIFT
>> 2625 int
>> 2626 default 6 if CPU_R3000 || CPU_TX39XX
>> 2627 default 0
>> 2628
>> 2629 config MIPS_ASID_BITS
>> 2630 int
>> 2631 default 0 if MIPS_ASID_BITS_VARIABLE
>> 2632 default 6 if CPU_R3000 || CPU_TX39XX
>> 2633 default 8
>> 2634
>> 2635 config MIPS_ASID_BITS_VARIABLE
>> 2636 bool
>> 2637
>> 2638 config MIPS_CRC_SUPPORT
>> 2639 bool
>> 2640
>> 2641 #
>> 2642 # - Highmem only makes sense for the 32-bit kernel.
>> 2643 # - The current highmem code will only work properly on physically indexed
>> 2644 # caches such as R3000, SB1, R7000 or those that look like they're virtually
>> 2645 # indexed such as R4000/R4400 SC and MC versions or R10000. So for the
>> 2646 # moment we protect the user and offer the highmem option only on machines
>> 2647 # where it's known to be safe. This will not offer highmem on a few systems
>> 2648 # such as MIPS32 and MIPS64 CPUs which may have virtual and physically
>> 2649 # indexed CPUs but we're playing safe.
>> 2650 # - We use SYS_SUPPORTS_HIGHMEM to offer highmem only for systems where we
>> 2651 # know they might have memory configurations that could make use of highmem
>> 2652 # support.
>> 2653 #
>> 2654 config HIGHMEM
>> 2655 bool "High Memory Support"
>> 2656 depends on 32BIT && CPU_SUPPORTS_HIGHMEM && SYS_SUPPORTS_HIGHMEM && !CPU_MIPS32_3_5_EVA
>> 2657
>> 2658 config CPU_SUPPORTS_HIGHMEM
>> 2659 bool
>> 2660
>> 2661 config SYS_SUPPORTS_HIGHMEM
>> 2662 bool
>> 2663
>> 2664 config SYS_SUPPORTS_SMARTMIPS
>> 2665 bool
>> 2666
>> 2667 config SYS_SUPPORTS_MICROMIPS
>> 2668 bool
>> 2669
>> 2670 config SYS_SUPPORTS_MIPS16
>> 2671 bool
>> 2672 help
>> 2673 This option must be set if a kernel might be executed on a MIPS16-
>> 2674 enabled CPU even if MIPS16 is not actually being used. In other
>> 2675 words, it makes the kernel MIPS16-tolerant.
>> 2676
>> 2677 config CPU_SUPPORTS_MSA
>> 2678 bool
>> 2679
>> 2680 config ARCH_FLATMEM_ENABLE
79 def_bool y 2681 def_bool y
>> 2682 depends on !NUMA && !CPU_LOONGSON2EF
80 2683
81 config STACKTRACE_SUPPORT !! 2684 config ARCH_SPARSEMEM_ENABLE
>> 2685 bool
>> 2686 select SPARSEMEM_STATIC if !SGI_IP27
>> 2687
>> 2688 config NUMA
>> 2689 bool "NUMA Support"
>> 2690 depends on SYS_SUPPORTS_NUMA
>> 2691 help
>> 2692 Say Y to compile the kernel to support NUMA (Non-Uniform Memory
>> 2693 Access). This option improves performance on systems with more
>> 2694 than two nodes; on two node systems it is generally better to
>> 2695 leave it disabled; on single node systems leave this option
>> 2696 disabled.
>> 2697
>> 2698 config SYS_SUPPORTS_NUMA
>> 2699 bool
>> 2700
>> 2701 config HAVE_SETUP_PER_CPU_AREA
82 def_bool y 2702 def_bool y
>> 2703 depends on NUMA
83 2704
84 config LOCKDEP_SUPPORT !! 2705 config NEED_PER_CPU_EMBED_FIRST_CHUNK
85 def_bool y 2706 def_bool y
>> 2707 depends on NUMA
86 2708
87 source "arch/microblaze/Kconfig.platform" !! 2709 config RELOCATABLE
>> 2710 bool "Relocatable kernel"
>> 2711 depends on SYS_SUPPORTS_RELOCATABLE && (CPU_MIPS32_R2 || CPU_MIPS64_R2 || CPU_MIPS32_R6 || CPU_MIPS64_R6 || CAVIUM_OCTEON_SOC)
>> 2712 help
>> 2713 This builds a kernel image that retains relocation information
>> 2714 so it can be loaded someplace besides the default 1MB.
>> 2715 The relocations make the kernel binary about 15% larger,
>> 2716 but are discarded at runtime
>> 2717
>> 2718 config RELOCATION_TABLE_SIZE
>> 2719 hex "Relocation table size"
>> 2720 depends on RELOCATABLE
>> 2721 range 0x0 0x01000000
>> 2722 default "0x00100000"
>> 2723 ---help---
>> 2724 A table of relocation data will be appended to the kernel binary
>> 2725 and parsed at boot to fix up the relocated kernel.
>> 2726
>> 2727 This option allows the amount of space reserved for the table to be
>> 2728 adjusted, although the default of 1Mb should be ok in most cases.
>> 2729
>> 2730 The build will fail and a valid size suggested if this is too small.
>> 2731
>> 2732 If unsure, leave at the default value.
>> 2733
>> 2734 config RANDOMIZE_BASE
>> 2735 bool "Randomize the address of the kernel image"
>> 2736 depends on RELOCATABLE
>> 2737 ---help---
>> 2738 Randomizes the physical and virtual address at which the
>> 2739 kernel image is loaded, as a security feature that
>> 2740 deters exploit attempts relying on knowledge of the location
>> 2741 of kernel internals.
>> 2742
>> 2743 Entropy is generated using any coprocessor 0 registers available.
>> 2744
>> 2745 The kernel will be offset by up to RANDOMIZE_BASE_MAX_OFFSET.
>> 2746
>> 2747 If unsure, say N.
>> 2748
>> 2749 config RANDOMIZE_BASE_MAX_OFFSET
>> 2750 hex "Maximum kASLR offset" if EXPERT
>> 2751 depends on RANDOMIZE_BASE
>> 2752 range 0x0 0x40000000 if EVA || 64BIT
>> 2753 range 0x0 0x08000000
>> 2754 default "0x01000000"
>> 2755 ---help---
>> 2756 When kASLR is active, this provides the maximum offset that will
>> 2757 be applied to the kernel image. It should be set according to the
>> 2758 amount of physical RAM available in the target system minus
>> 2759 PHYSICAL_START and must be a power of 2.
88 2760
89 menu "Processor type and features" !! 2761 This is limited by the size of KSEG0, 256Mb on 32-bit or 1Gb with
>> 2762 EVA or 64-bit. The default is 16Mb.
90 2763
91 source "kernel/Kconfig.hz" !! 2764 config NODES_SHIFT
>> 2765 int
>> 2766 default "6"
>> 2767 depends on NEED_MULTIPLE_NODES
92 2768
93 config MMU !! 2769 config HW_PERF_EVENTS
94 def_bool y !! 2770 bool "Enable hardware performance counter support for perf events"
>> 2771 depends on PERF_EVENTS && !OPROFILE && (CPU_MIPS32 || CPU_MIPS64 || CPU_R10000 || CPU_SB1 || CPU_CAVIUM_OCTEON || CPU_XLP || CPU_LOONGSON64)
>> 2772 default y
>> 2773 help
>> 2774 Enable hardware performance counter support for perf events. If
>> 2775 disabled, perf events will use software events only.
95 2776
96 comment "Boot options" !! 2777 config DMI
>> 2778 bool "Enable DMI scanning"
>> 2779 depends on MACH_LOONGSON64
>> 2780 select DMI_SCAN_MACHINE_NON_EFI_FALLBACK
>> 2781 default y
>> 2782 help
>> 2783 Enabled scanning of DMI to identify machine quirks. Say Y
>> 2784 here unless you have verified that your setup is not
>> 2785 affected by entries in the DMI blacklist. Required by PNP
>> 2786 BIOS code.
>> 2787
>> 2788 config SMP
>> 2789 bool "Multi-Processing support"
>> 2790 depends on SYS_SUPPORTS_SMP
>> 2791 help
>> 2792 This enables support for systems with more than one CPU. If you have
>> 2793 a system with only one CPU, say N. If you have a system with more
>> 2794 than one CPU, say Y.
>> 2795
>> 2796 If you say N here, the kernel will run on uni- and multiprocessor
>> 2797 machines, but will use only one CPU of a multiprocessor machine. If
>> 2798 you say Y here, the kernel will run on many, but not all,
>> 2799 uniprocessor machines. On a uniprocessor machine, the kernel
>> 2800 will run faster if you say N here.
>> 2801
>> 2802 People using multiprocessor machines who say Y here should also say
>> 2803 Y to "Enhanced Real Time Clock Support", below.
>> 2804
>> 2805 See also the SMP-HOWTO available at
>> 2806 <http://www.tldp.org/docs.html#howto>.
>> 2807
>> 2808 If you don't know what to do here, say N.
>> 2809
>> 2810 config HOTPLUG_CPU
>> 2811 bool "Support for hot-pluggable CPUs"
>> 2812 depends on SMP && SYS_SUPPORTS_HOTPLUG_CPU
>> 2813 help
>> 2814 Say Y here to allow turning CPUs off and on. CPUs can be
>> 2815 controlled through /sys/devices/system/cpu.
>> 2816 (Note: power management support will enable this option
>> 2817 automatically on SMP systems. )
>> 2818 Say N if you want to disable CPU hotplug.
97 2819
98 config CMDLINE_BOOL !! 2820 config SMP_UP
99 bool "Default bootloader kernel argume !! 2821 bool
100 2822
101 config CMDLINE !! 2823 config SYS_SUPPORTS_MIPS_CMP
102 string "Default kernel command string" !! 2824 bool
103 depends on CMDLINE_BOOL <<
104 default "console=ttyUL0,115200" <<
105 help <<
106 On some architectures there is curre <<
107 to pass arguments to the kernel. For <<
108 supply some command-line options at <<
109 here. <<
110 2825
111 config CMDLINE_FORCE !! 2826 config SYS_SUPPORTS_MIPS_CPS
112 bool "Force default kernel command str !! 2827 bool
113 depends on CMDLINE_BOOL !! 2828
114 default n !! 2829 config SYS_SUPPORTS_SMP
>> 2830 bool
>> 2831
>> 2832 config NR_CPUS_DEFAULT_4
>> 2833 bool
>> 2834
>> 2835 config NR_CPUS_DEFAULT_8
>> 2836 bool
>> 2837
>> 2838 config NR_CPUS_DEFAULT_16
>> 2839 bool
>> 2840
>> 2841 config NR_CPUS_DEFAULT_32
>> 2842 bool
>> 2843
>> 2844 config NR_CPUS_DEFAULT_64
>> 2845 bool
>> 2846
>> 2847 config NR_CPUS
>> 2848 int "Maximum number of CPUs (2-256)"
>> 2849 range 2 256
>> 2850 depends on SMP
>> 2851 default "4" if NR_CPUS_DEFAULT_4
>> 2852 default "8" if NR_CPUS_DEFAULT_8
>> 2853 default "16" if NR_CPUS_DEFAULT_16
>> 2854 default "32" if NR_CPUS_DEFAULT_32
>> 2855 default "64" if NR_CPUS_DEFAULT_64
>> 2856 help
>> 2857 This allows you to specify the maximum number of CPUs which this
>> 2858 kernel will support. The maximum supported value is 32 for 32-bit
>> 2859 kernel and 64 for 64-bit kernels; the minimum value which makes
>> 2860 sense is 1 for Qemu (useful only for kernel debugging purposes)
>> 2861 and 2 for all others.
>> 2862
>> 2863 This is purely to save memory - each supported CPU adds
>> 2864 approximately eight kilobytes to the kernel image. For best
>> 2865 performance should round up your number of processors to the next
>> 2866 power of two.
>> 2867
>> 2868 config MIPS_PERF_SHARED_TC_COUNTERS
>> 2869 bool
>> 2870
>> 2871 config MIPS_NR_CPU_NR_MAP_1024
>> 2872 bool
>> 2873
>> 2874 config MIPS_NR_CPU_NR_MAP
>> 2875 int
>> 2876 depends on SMP
>> 2877 default 1024 if MIPS_NR_CPU_NR_MAP_1024
>> 2878 default NR_CPUS if !MIPS_NR_CPU_NR_MAP_1024
>> 2879
>> 2880 #
>> 2881 # Timer Interrupt Frequency Configuration
>> 2882 #
>> 2883
>> 2884 choice
>> 2885 prompt "Timer frequency"
>> 2886 default HZ_250
>> 2887 help
>> 2888 Allows the configuration of the timer frequency.
>> 2889
>> 2890 config HZ_24
>> 2891 bool "24 HZ" if SYS_SUPPORTS_24HZ || SYS_SUPPORTS_ARBIT_HZ
>> 2892
>> 2893 config HZ_48
>> 2894 bool "48 HZ" if SYS_SUPPORTS_48HZ || SYS_SUPPORTS_ARBIT_HZ
>> 2895
>> 2896 config HZ_100
>> 2897 bool "100 HZ" if SYS_SUPPORTS_100HZ || SYS_SUPPORTS_ARBIT_HZ
>> 2898
>> 2899 config HZ_128
>> 2900 bool "128 HZ" if SYS_SUPPORTS_128HZ || SYS_SUPPORTS_ARBIT_HZ
>> 2901
>> 2902 config HZ_250
>> 2903 bool "250 HZ" if SYS_SUPPORTS_250HZ || SYS_SUPPORTS_ARBIT_HZ
>> 2904
>> 2905 config HZ_256
>> 2906 bool "256 HZ" if SYS_SUPPORTS_256HZ || SYS_SUPPORTS_ARBIT_HZ
>> 2907
>> 2908 config HZ_1000
>> 2909 bool "1000 HZ" if SYS_SUPPORTS_1000HZ || SYS_SUPPORTS_ARBIT_HZ
>> 2910
>> 2911 config HZ_1024
>> 2912 bool "1024 HZ" if SYS_SUPPORTS_1024HZ || SYS_SUPPORTS_ARBIT_HZ
>> 2913
>> 2914 endchoice
>> 2915
>> 2916 config SYS_SUPPORTS_24HZ
>> 2917 bool
>> 2918
>> 2919 config SYS_SUPPORTS_48HZ
>> 2920 bool
>> 2921
>> 2922 config SYS_SUPPORTS_100HZ
>> 2923 bool
>> 2924
>> 2925 config SYS_SUPPORTS_128HZ
>> 2926 bool
>> 2927
>> 2928 config SYS_SUPPORTS_250HZ
>> 2929 bool
>> 2930
>> 2931 config SYS_SUPPORTS_256HZ
>> 2932 bool
>> 2933
>> 2934 config SYS_SUPPORTS_1000HZ
>> 2935 bool
>> 2936
>> 2937 config SYS_SUPPORTS_1024HZ
>> 2938 bool
>> 2939
>> 2940 config SYS_SUPPORTS_ARBIT_HZ
>> 2941 bool
>> 2942 default y if !SYS_SUPPORTS_24HZ && \
>> 2943 !SYS_SUPPORTS_48HZ && \
>> 2944 !SYS_SUPPORTS_100HZ && \
>> 2945 !SYS_SUPPORTS_128HZ && \
>> 2946 !SYS_SUPPORTS_250HZ && \
>> 2947 !SYS_SUPPORTS_256HZ && \
>> 2948 !SYS_SUPPORTS_1000HZ && \
>> 2949 !SYS_SUPPORTS_1024HZ
>> 2950
>> 2951 config HZ
>> 2952 int
>> 2953 default 24 if HZ_24
>> 2954 default 48 if HZ_48
>> 2955 default 100 if HZ_100
>> 2956 default 128 if HZ_128
>> 2957 default 250 if HZ_250
>> 2958 default 256 if HZ_256
>> 2959 default 1000 if HZ_1000
>> 2960 default 1024 if HZ_1024
>> 2961
>> 2962 config SCHED_HRTICK
>> 2963 def_bool HIGH_RES_TIMERS
>> 2964
>> 2965 config KEXEC
>> 2966 bool "Kexec system call"
>> 2967 select KEXEC_CORE
>> 2968 help
>> 2969 kexec is a system call that implements the ability to shutdown your
>> 2970 current kernel, and to start another kernel. It is like a reboot
>> 2971 but it is independent of the system firmware. And like a reboot
>> 2972 you can start any kernel with it, not just Linux.
>> 2973
>> 2974 The name comes from the similarity to the exec system call.
>> 2975
>> 2976 It is an ongoing process to be certain the hardware in a machine
>> 2977 is properly shutdown, so do not be surprised if this code does not
>> 2978 initially work for you. As of this writing the exact hardware
>> 2979 interface is strongly in flux, so no good recommendation can be
>> 2980 made.
>> 2981
>> 2982 config CRASH_DUMP
>> 2983 bool "Kernel crash dumps"
>> 2984 help
>> 2985 Generate crash dump after being started by kexec.
>> 2986 This should be normally only set in special crash dump kernels
>> 2987 which are loaded in the main kernel with kexec-tools into
>> 2988 a specially reserved region and then later executed after
>> 2989 a crash by kdump/kexec. The crash dump kernel must be compiled
>> 2990 to a memory address not used by the main kernel or firmware using
>> 2991 PHYSICAL_START.
>> 2992
>> 2993 config PHYSICAL_START
>> 2994 hex "Physical address where the kernel is loaded"
>> 2995 default "0xffffffff84000000"
>> 2996 depends on CRASH_DUMP
115 help 2997 help
116 Set this to have arguments from the !! 2998 This gives the CKSEG0 or KSEG0 address where the kernel is loaded.
117 override those passed by the boot lo !! 2999 If you plan to use kernel for capturing the crash dump change
>> 3000 this value to start of the reserved region (the "X" value as
>> 3001 specified in the "crashkernel=YM@XM" command line boot parameter
>> 3002 passed to the panic-ed kernel).
>> 3003
>> 3004 config SECCOMP
>> 3005 bool "Enable seccomp to safely compute untrusted bytecode"
>> 3006 depends on PROC_FS
>> 3007 default y
>> 3008 help
>> 3009 This kernel feature is useful for number crunching applications
>> 3010 that may need to compute untrusted bytecode during their
>> 3011 execution. By using pipes or other transports made available to
>> 3012 the process as file descriptors supporting the read/write
>> 3013 syscalls, it's possible to isolate those applications in
>> 3014 their own address space using seccomp. Once seccomp is
>> 3015 enabled via /proc/<pid>/seccomp, it cannot be disabled
>> 3016 and the task is only allowed to execute a few safe syscalls
>> 3017 defined by each seccomp mode.
>> 3018
>> 3019 If unsure, say Y. Only embedded should say N here.
>> 3020
>> 3021 config MIPS_O32_FP64_SUPPORT
>> 3022 bool "Support for O32 binaries using 64-bit FP" if !CPU_MIPSR6
>> 3023 depends on 32BIT || MIPS32_O32
>> 3024 help
>> 3025 When this is enabled, the kernel will support use of 64-bit floating
>> 3026 point registers with binaries using the O32 ABI along with the
>> 3027 EF_MIPS_FP64 ELF header flag (typically built with -mfp64). On
>> 3028 32-bit MIPS systems this support is at the cost of increasing the
>> 3029 size and complexity of the compiled FPU emulator. Thus if you are
>> 3030 running a MIPS32 system and know that none of your userland binaries
>> 3031 will require 64-bit floating point, you may wish to reduce the size
>> 3032 of your kernel & potentially improve FP emulation performance by
>> 3033 saying N here.
>> 3034
>> 3035 Although binutils currently supports use of this flag the details
>> 3036 concerning its effect upon the O32 ABI in userland are still being
>> 3037 worked on. In order to avoid userland becoming dependant upon current
>> 3038 behaviour before the details have been finalised, this option should
>> 3039 be considered experimental and only enabled by those working upon
>> 3040 said details.
>> 3041
>> 3042 If unsure, say N.
>> 3043
>> 3044 config USE_OF
>> 3045 bool
>> 3046 select OF
>> 3047 select OF_EARLY_FLATTREE
>> 3048 select IRQ_DOMAIN
>> 3049
>> 3050 config UHI_BOOT
>> 3051 bool
>> 3052
>> 3053 config BUILTIN_DTB
>> 3054 bool
>> 3055
>> 3056 choice
>> 3057 prompt "Kernel appended dtb support" if USE_OF
>> 3058 default MIPS_NO_APPENDED_DTB
>> 3059
>> 3060 config MIPS_NO_APPENDED_DTB
>> 3061 bool "None"
>> 3062 help
>> 3063 Do not enable appended dtb support.
>> 3064
>> 3065 config MIPS_ELF_APPENDED_DTB
>> 3066 bool "vmlinux"
>> 3067 help
>> 3068 With this option, the boot code will look for a device tree binary
>> 3069 DTB) included in the vmlinux ELF section .appended_dtb. By default
>> 3070 it is empty and the DTB can be appended using binutils command
>> 3071 objcopy:
>> 3072
>> 3073 objcopy --update-section .appended_dtb=<filename>.dtb vmlinux
>> 3074
>> 3075 This is meant as a backward compatiblity convenience for those
>> 3076 systems with a bootloader that can't be upgraded to accommodate
>> 3077 the documented boot protocol using a device tree.
>> 3078
>> 3079 config MIPS_RAW_APPENDED_DTB
>> 3080 bool "vmlinux.bin or vmlinuz.bin"
>> 3081 help
>> 3082 With this option, the boot code will look for a device tree binary
>> 3083 DTB) appended to raw vmlinux.bin or vmlinuz.bin.
>> 3084 (e.g. cat vmlinux.bin <filename>.dtb > vmlinux_w_dtb).
>> 3085
>> 3086 This is meant as a backward compatibility convenience for those
>> 3087 systems with a bootloader that can't be upgraded to accommodate
>> 3088 the documented boot protocol using a device tree.
>> 3089
>> 3090 Beware that there is very little in terms of protection against
>> 3091 this option being confused by leftover garbage in memory that might
>> 3092 look like a DTB header after a reboot if no actual DTB is appended
>> 3093 to vmlinux.bin. Do not leave this option active in a production kernel
>> 3094 if you don't intend to always append a DTB.
>> 3095 endchoice
>> 3096
>> 3097 choice
>> 3098 prompt "Kernel command line type" if !CMDLINE_OVERRIDE
>> 3099 default MIPS_CMDLINE_FROM_DTB if USE_OF && !ATH79 && !MACH_INGENIC && \
>> 3100 !MACH_LOONGSON64 && !MIPS_MALTA && \
>> 3101 !CAVIUM_OCTEON_SOC
>> 3102 default MIPS_CMDLINE_FROM_BOOTLOADER
>> 3103
>> 3104 config MIPS_CMDLINE_FROM_DTB
>> 3105 depends on USE_OF
>> 3106 bool "Dtb kernel arguments if available"
>> 3107
>> 3108 config MIPS_CMDLINE_DTB_EXTEND
>> 3109 depends on USE_OF
>> 3110 bool "Extend dtb kernel arguments with bootloader arguments"
>> 3111
>> 3112 config MIPS_CMDLINE_FROM_BOOTLOADER
>> 3113 bool "Bootloader kernel arguments if available"
>> 3114
>> 3115 config MIPS_CMDLINE_BUILTIN_EXTEND
>> 3116 depends on CMDLINE_BOOL
>> 3117 bool "Extend builtin kernel arguments with bootloader arguments"
>> 3118 endchoice
118 3119
119 endmenu 3120 endmenu
120 3121
121 menu "Kernel features" !! 3122 config LOCKDEP_SUPPORT
>> 3123 bool
>> 3124 default y
122 3125
123 config NR_CPUS !! 3126 config STACKTRACE_SUPPORT
>> 3127 bool
>> 3128 default y
>> 3129
>> 3130 config PGTABLE_LEVELS
124 int 3131 int
125 default "1" !! 3132 default 4 if PAGE_SIZE_4KB && MIPS_VA_BITS_48
>> 3133 default 3 if 64BIT && !PAGE_SIZE_64KB
>> 3134 default 2
126 3135
127 config ADVANCED_OPTIONS !! 3136 config MIPS_AUTO_PFN_OFFSET
128 bool "Prompt for advanced kernel confi !! 3137 bool
>> 3138
>> 3139 menu "Bus options (PCI, PCMCIA, EISA, ISA, TC)"
>> 3140
>> 3141 config PCI_DRIVERS_GENERIC
>> 3142 select PCI_DOMAINS_GENERIC if PCI
>> 3143 bool
>> 3144
>> 3145 config PCI_DRIVERS_LEGACY
>> 3146 def_bool !PCI_DRIVERS_GENERIC
>> 3147 select NO_GENERIC_PCI_IOPORT_MAP
>> 3148 select PCI_DOMAINS if PCI
>> 3149
>> 3150 #
>> 3151 # ISA support is now enabled via select. Too many systems still have the one
>> 3152 # or other ISA chip on the board that users don't know about so don't expect
>> 3153 # users to choose the right thing ...
>> 3154 #
>> 3155 config ISA
>> 3156 bool
>> 3157
>> 3158 config TC
>> 3159 bool "TURBOchannel support"
>> 3160 depends on MACH_DECSTATION
129 help 3161 help
130 This option will enable prompting fo !! 3162 TURBOchannel is a DEC (now Compaq (now HP)) bus for Alpha and MIPS
131 configuration options. These option !! 3163 processors. TURBOchannel programming specifications are available
132 work if they are set incorrectly, bu !! 3164 at:
133 aspects of kernel memory management. !! 3165 <ftp://ftp.hp.com/pub/alphaserver/archive/triadd/>
>> 3166 and:
>> 3167 <http://www.computer-refuge.org/classiccmp/ftp.digital.com/pub/DEC/TriAdd/>
>> 3168 Linux driver support status is documented at:
>> 3169 <http://www.linux-mips.org/wiki/DECstation>
>> 3170
>> 3171 config MMU
>> 3172 bool
>> 3173 default y
134 3174
135 Unless you know what you are doing, !! 3175 config ARCH_MMAP_RND_BITS_MIN
>> 3176 default 12 if 64BIT
>> 3177 default 8
>> 3178
>> 3179 config ARCH_MMAP_RND_BITS_MAX
>> 3180 default 18 if 64BIT
>> 3181 default 15
>> 3182
>> 3183 config ARCH_MMAP_RND_COMPAT_BITS_MIN
>> 3184 default 8
>> 3185
>> 3186 config ARCH_MMAP_RND_COMPAT_BITS_MAX
>> 3187 default 15
>> 3188
>> 3189 config I8253
>> 3190 bool
>> 3191 select CLKSRC_I8253
>> 3192 select CLKEVT_I8253
>> 3193 select MIPS_EXTERNAL_TIMER
136 3194
137 comment "Default settings for advanced configu !! 3195 config ZONE_DMA
138 depends on !ADVANCED_OPTIONS !! 3196 bool
139 3197
140 config HIGHMEM !! 3198 config ZONE_DMA32
141 bool "High memory support" !! 3199 bool
142 select KMAP_LOCAL !! 3200
>> 3201 endmenu
>> 3202
>> 3203 config TRAD_SIGNALS
>> 3204 bool
>> 3205
>> 3206 config MIPS32_COMPAT
>> 3207 bool
>> 3208
>> 3209 config COMPAT
>> 3210 bool
>> 3211
>> 3212 config SYSVIPC_COMPAT
>> 3213 bool
>> 3214
>> 3215 config MIPS32_O32
>> 3216 bool "Kernel support for o32 binaries"
>> 3217 depends on 64BIT
>> 3218 select ARCH_WANT_OLD_COMPAT_IPC
>> 3219 select COMPAT
>> 3220 select MIPS32_COMPAT
>> 3221 select SYSVIPC_COMPAT if SYSVIPC
143 help 3222 help
144 The address space of Microblaze proc !! 3223 Select this option if you want to run o32 binaries. These are pure
145 and it has to accommodate user addre !! 3224 32-bit binaries as used by the 32-bit Linux/MIPS port. Most of
146 space as well as some memory mapped !! 3225 existing binaries are in this format.
147 have a large amount of physical memo !! 3226
148 memory can be "permanently mapped" b !! 3227 If unsure, say Y.
149 memory that is not permanently mappe !! 3228
150 !! 3229 config MIPS32_N32
151 If unsure, say n. !! 3230 bool "Kernel support for n32 binaries"
152 !! 3231 depends on 64BIT
153 config LOWMEM_SIZE_BOOL !! 3232 select ARCH_WANT_COMPAT_IPC_PARSE_VERSION
154 bool "Set maximum low memory" !! 3233 select COMPAT
155 depends on ADVANCED_OPTIONS !! 3234 select MIPS32_COMPAT
156 help !! 3235 select SYSVIPC_COMPAT if SYSVIPC
157 This option allows you to set the ma !! 3236 help
158 will be used as "low memory", that i !! 3237 Select this option if you want to run n32 binaries. These are
159 access directly, without having to s !! 3238 64-bit binaries using 32-bit quantities for addressing and certain
160 This can be useful in optimizing the !! 3239 data that would normally be 64-bit. They are used in special
161 memory. !! 3240 cases.
162 !! 3241
163 Say N here unless you know what you !! 3242 If unsure, say N.
164 !! 3243
165 config LOWMEM_SIZE !! 3244 config BINFMT_ELF32
166 hex "Maximum low memory size (in bytes !! 3245 bool
167 default "0x30000000" !! 3246 default y if MIPS32_O32 || MIPS32_N32
168 !! 3247 select ELFCORE
169 config MANUAL_RESET_VECTOR <<
170 hex "Microblaze reset vector address s <<
171 default "0x0" <<
172 help <<
173 Set this option to have the kernel o <<
174 If zero, no change will be made to t <<
175 address 0x0. <<
176 If non-zero, a jump instruction to t <<
177 to the reset vector at address 0x0. <<
178 If you are unsure, set it to default <<
179 <<
180 config KERNEL_START_BOOL <<
181 bool "Set custom kernel base address" <<
182 depends on ADVANCED_OPTIONS <<
183 help <<
184 This option allows you to set the ke <<
185 the kernel will map low memory (the <<
186 this address). This can be useful i <<
187 layout of the system. <<
188 <<
189 Say N here unless you know what you <<
190 <<
191 config KERNEL_START <<
192 hex "Virtual address of kernel base" i <<
193 default "0xc0000000" <<
194 <<
195 config TASK_SIZE_BOOL <<
196 bool "Set custom user task size" <<
197 depends on ADVANCED_OPTIONS <<
198 help <<
199 This option allows you to set the am <<
200 allocated to user tasks. This can b <<
201 virtual memory layout of the system. <<
202 <<
203 Say N here unless you know what you <<
204 <<
205 config TASK_SIZE <<
206 hex "Size of user task space" if TASK_ <<
207 default "0x80000000" <<
208 <<
209 config MB_MANAGER <<
210 bool "Support for Microblaze Manager" <<
211 depends on ADVANCED_OPTIONS <<
212 help <<
213 This option enables API for configur <<
214 control register, which is consumed <<
215 block the break. <<
216 3248
217 Say N here unless you know what you !! 3249 menu "Power management options"
>> 3250
>> 3251 config ARCH_HIBERNATION_POSSIBLE
>> 3252 def_bool y
>> 3253 depends on SYS_SUPPORTS_HOTPLUG_CPU || !SMP
>> 3254
>> 3255 config ARCH_SUSPEND_POSSIBLE
>> 3256 def_bool y
>> 3257 depends on SYS_SUPPORTS_HOTPLUG_CPU || !SMP
>> 3258
>> 3259 source "kernel/power/Kconfig"
218 3260
219 endmenu 3261 endmenu
>> 3262
>> 3263 config MIPS_EXTERNAL_TIMER
>> 3264 bool
>> 3265
>> 3266 menu "CPU Power Management"
>> 3267
>> 3268 if CPU_SUPPORTS_CPUFREQ && MIPS_EXTERNAL_TIMER
>> 3269 source "drivers/cpufreq/Kconfig"
>> 3270 endif
>> 3271
>> 3272 source "drivers/cpuidle/Kconfig"
>> 3273
>> 3274 endmenu
>> 3275
>> 3276 source "drivers/firmware/Kconfig"
>> 3277
>> 3278 source "arch/mips/kvm/Kconfig"
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.