1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2 /*
3 * Device Tree file for Synology DS414
4 *
5 * Copyright (C) 2014, Arnaud EBALARD <arno@nat
6 *
7 * Note: this Device Tree assumes that the boo
8 * internal registers to 0xf1000000 (instead o
9 * The 0xf1000000 is the default used by the r
10 * bootloaders provided by Marvell. It is used
11 * DSM software provided by Synology. Nonethel
12 * were delivered with an older version of u-b
13 * registers mapped at 0xd0000000. If you have
14 * not be able to directly boot a kernel based
15 * that case, the preferred solution is to upd
16 * by upgrading to latest version of DSM, or b
17 * installing it from u-boot prompt) or adjust
18 * (s/0xf1000000/0xd0000000/ in 'ranges' below
19 */
20
21 /dts-v1/;
22
23 #include <dt-bindings/input/input.h>
24 #include <dt-bindings/gpio/gpio.h>
25 #include "armada-xp-mv78230.dtsi"
26
27 / {
28 model = "Synology DS414";
29 compatible = "synology,ds414", "marvel
30 "marvell,armadaxp", "marv
31
32 chosen {
33 stdout-path = "serial0:115200n
34 };
35
36 memory@0 {
37 device_type = "memory";
38 reg = <0 0x00000000 0 0x400000
39 };
40
41 soc {
42 ranges = <MBUS_ID(0xf0, 0x01)
43 MBUS_ID(0x01, 0x1d)
44 MBUS_ID(0x09, 0x09)
45 MBUS_ID(0x09, 0x05)
46
47 internal-regs {
48
49 /* RTC is provided by
50 rtc@10300 {
51 status = "disa
52 };
53
54 i2c@11000 {
55 clock-frequenc
56 status = "okay
57
58 s35390a: s3539
59 compa
60 reg =
61 };
62 };
63
64 /* Connected to a head
65 * provides the main c
66 *
67 * Warning: the device
68 * USB-serial converte
69 * button is pressed.
70 * connected a few sec
71 * power button. This
72 * pin being sampled a
73 */
74 serial@12000 {
75 status = "okay
76 };
77
78 /* Connected to a Micr
79 serial@12100 {
80 status = "okay
81 };
82
83 poweroff@12100 {
84 compatible = "
85 reg = <0x12100
86 clocks = <&cor
87 };
88
89 /* Front USB 2.0 port
90 usb@50000 {
91 status = "okay
92 };
93
94 ethernet@70000 {
95 status = "okay
96 pinctrl-0 = <&
97 pinctrl-names
98 phy = <&phy1>;
99 phy-mode = "rg
100 };
101
102 ethernet@74000 {
103 pinctrl-0 = <&
104 pinctrl-names
105 status = "okay
106 phy = <&phy0>;
107 phy-mode = "rg
108 };
109 };
110 };
111
112 sata1_regulator: sata1-regulator-1 {
113 compatible = "regulator-fixed"
114 regulator-name = "SATA1 Power"
115 regulator-min-microvolt = <500
116 regulator-max-microvolt = <500
117 startup-delay-us = <2000000>;
118 enable-active-high;
119 regulator-always-on;
120 regulator-boot-on;
121 gpio = <&gpio1 10 GPIO_ACTIVE_
122 pinctrl-0 = <&sata1_pwr_pin>;
123 pinctrl-names = "default";
124 };
125
126 sata2_regulator: sata2-regulator-2 {
127 compatible = "regulator-fixed"
128 regulator-name = "SATA2 Power"
129 regulator-min-microvolt = <500
130 regulator-max-microvolt = <500
131 startup-delay-us = <4000000>;
132 enable-active-high;
133 regulator-always-on;
134 regulator-boot-on;
135 gpio = <&gpio1 12 GPIO_ACTIVE_
136 pinctrl-0 = <&sata2_pwr_pin>;
137 pinctrl-names = "default";
138 };
139
140 sata3_regulator: sata3-regulator-3 {
141 compatible = "regulator-fixed"
142 regulator-name = "SATA3 Power"
143 regulator-min-microvolt = <500
144 regulator-max-microvolt = <500
145 startup-delay-us = <6000000>;
146 enable-active-high;
147 regulator-always-on;
148 regulator-boot-on;
149 gpio = <&gpio1 13 GPIO_ACTIVE_
150 pinctrl-0 = <&sata3_pwr_pin>;
151 pinctrl-names = "default";
152 };
153
154 sata4_regulator: sata4-regulator-4 {
155 compatible = "regulator-fixed"
156 regulator-name = "SATA4 Power"
157 regulator-min-microvolt = <500
158 regulator-max-microvolt = <500
159 startup-delay-us = <8000000>;
160 enable-active-high;
161 regulator-always-on;
162 regulator-boot-on;
163 gpio = <&gpio1 14 GPIO_ACTIVE_
164 pinctrl-0 = <&sata4_pwr_pin>;
165 pinctrl-names = "default";
166 };
167 };
168
169 &pciec {
170 status = "okay";
171
172 /*
173 * Connected to Marvell 88SX7042 SATA-
174 * handling the four disks.
175 */
176 pcie@1,0 {
177 /* Port 0, Lane 0 */
178 status = "okay";
179 };
180
181 /*
182 * Connected to EtronTech EJ168A XHCI
183 * providing the two rear USB 3.0 port
184 */
185 pcie@5,0 {
186 /* Port 1, Lane 0 */
187 status = "okay";
188 };
189 };
190
191
192 &mdio {
193 phy0: ethernet-phy@0 { /* Marvell 88E1
194 reg = <0>;
195 };
196
197 phy1: ethernet-phy@1 { /* Marvell 88E1
198 reg = <1>;
199 };
200 };
201
202 &pinctrl {
203 sata1_pwr_pin: sata1-pwr-pin {
204 marvell,pins = "mpp42";
205 marvell,function = "gpio";
206 };
207
208 sata2_pwr_pin: sata2-pwr-pin {
209 marvell,pins = "mpp44";
210 marvell,function = "gpio";
211 };
212
213 sata3_pwr_pin: sata3-pwr-pin {
214 marvell,pins = "mpp45";
215 marvell,function = "gpio";
216 };
217
218 sata4_pwr_pin: sata4-pwr-pin {
219 marvell,pins = "mpp46";
220 marvell,function = "gpio";
221 };
222
223 sata1_pres_pin: sata1-pres-pin {
224 marvell,pins = "mpp34";
225 marvell,function = "gpio";
226 };
227
228 sata2_pres_pin: sata2-pres-pin {
229 marvell,pins = "mpp35";
230 marvell,function = "gpio";
231 };
232
233 sata3_pres_pin: sata3-pres-pin {
234 marvell,pins = "mpp40";
235 marvell,function = "gpio";
236 };
237
238 sata4_pres_pin: sata4-pres-pin {
239 marvell,pins = "mpp41";
240 marvell,function = "gpio";
241 };
242
243 syno_id_bit0_pin: syno-id-bit0-pin {
244 marvell,pins = "mpp26";
245 marvell,function = "gpio";
246 };
247
248 syno_id_bit1_pin: syno-id-bit1-pin {
249 marvell,pins = "mpp28";
250 marvell,function = "gpio";
251 };
252
253 syno_id_bit2_pin: syno-id-bit2-pin {
254 marvell,pins = "mpp29";
255 marvell,function = "gpio";
256 };
257
258 fan1_alarm_pin: fan1-alarm-pin {
259 marvell,pins = "mpp33";
260 marvell,function = "gpio";
261 };
262
263 fan2_alarm_pin: fan2-alarm-pin {
264 marvell,pins = "mpp32";
265 marvell,function = "gpio";
266 };
267 };
268
269 &spi0 {
270 status = "okay";
271
272 flash@0 {
273 #address-cells = <1>;
274 #size-cells = <1>;
275 compatible = "micron,n25q064",
276 reg = <0>; /* Chip select 0 */
277 spi-max-frequency = <20000000>
278
279 /*
280 * Warning!
281 *
282 * Synology u-boot uses its co
283 * and it seems Synology did n
284 * default configuration in or
285 * modified environment at a s
286 * if you do a 'saveenv' under
287 * environment will be saved a
288 * of the flash, i.e. in the m
289 * For that reason, it is stro
290 * change the default environm
291 * what you are doing.
292 */
293 partition@0 { /* u-boot */
294 label = "RedBoot";
295 reg = <0x00000000 0x00
296 };
297
298 partition@c0000 { /* uImage */
299 label = "zImage";
300 reg = <0x000d0000 0x00
301 };
302
303 partition@3a0000 { /* uInitram
304 label = "rd.gz";
305 reg = <0x003a0000 0x00
306 };
307
308 partition@7d0000 { /* MAC addr
309 label = "vendor";
310 reg = <0x007d0000 0x00
311 };
312
313 partition@7e0000 {
314 label = "RedBoot confi
315 reg = <0x007e0000 0x00
316 };
317
318 partition@7f0000 {
319 label = "FIS directory
320 reg = <0x007f0000 0x00
321 };
322 };
323 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.