1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * dts file for Hisilicon HiKey970 Development
4 *
5 * Copyright (C) 2016, HiSilicon Ltd.
6 * Copyright (C) 2018, Linaro Ltd.
7 *
8 */
9
10 /dts-v1/;
11 #include <dt-bindings/gpio/gpio.h>
12
13 #include "hi3670.dtsi"
14 #include "hikey970-pinctrl.dtsi"
15 #include "hikey970-pmic.dtsi"
16
17 / {
18 model = "HiKey970";
19 compatible = "hisilicon,hi3670-hikey97
20
21 aliases {
22 mshc1 = &dwmmc1;
23 mshc2 = &dwmmc2;
24 serial0 = &uart0;
25 serial1 = &uart1;
26 serial2 = &uart2;
27 serial3 = &uart3;
28 serial4 = &uart4;
29 serial5 = &uart5;
30 serial6 = &uart6; /* con
31 };
32
33 chosen {
34 stdout-path = "serial6:115200n
35 };
36
37 memory@0 {
38 device_type = "memory";
39 /* expect bootloader to fill i
40 reg = <0x0 0x0 0x0 0x0>;
41 };
42
43 wlan_en: wlan-en-1-8v {
44 compatible = "regulator-fixed"
45 regulator-name = "wlan-en-regu
46 regulator-min-microvolt = <180
47 regulator-max-microvolt = <180
48
49 /* GPIO_051_WIFI_EN */
50 gpio = <&gpio6 3 0>;
51
52 /* WLAN card specific delay */
53 startup-delay-us = <70000>;
54 enable-active-high;
55 };
56 };
57
58 /*
59 * Legend: proper name = the GPIO line is used
60 * NC = not connected (pin out but not
61 * anything the board)
62 * "[PER]" = pin is muxed for [periphe
63 * "" = no idea, schematic doesn't say
64 * unrouted (not connected to any
65 * LSEC = Low Speed External Connector
66 * HSEC = High Speed External Connecto
67 *
68 * Line names are taken from "hikey970-schemat
69 *
70 * For the lines routed to the external connec
71 * lines are named after the 96Boards CE Speci
72 * Appendix "Expansion Connector Signal Descri
73 *
74 * When the 96Board naming of a line and the s
75 * the same line are in conflict, the 96Board
76 * takes precedence, which means that the exte
77 * LSEC is named UART0 while the schematic and
78 * UART2. This is only for the informational l
79 * the GPIO named lines "GPIO-A" thru "GPIO-L"
80 * ones actually used for GPIO.
81 */
82 &gpio0 {
83 /* GPIO_000-GPIO_007 */
84 gpio-line-names =
85 "",
86 "TP901", /* TEST_MODE connecte
87 "",
88 "GPIO_003_USB_HUB_RESET_N",
89 "NC",
90 "[AP_GPS_REF_CLK]",
91 "[I2C3_SCL]",
92 "[I2C3_SDA]";
93 };
94
95 &gpio1 {
96 /* GPIO_008-GPIO_015 */
97 gpio-line-names =
98 "[UART0_CTS]", /* LSEC pin 3:
99 "[UART0_RTS]", /* LSEC pin 9:
100 "[UART0_TXD]", /* LSEC pin 5:
101 "[UART0_RXD]", /* LSEC pin 7:
102 "[USER_LED5]",
103 "GPIO-I", /* LSEC pin 31: GPIO
104 "[USER_LED3]",
105 "[USER_LED4]";
106 };
107
108 &gpio2 {
109 /* GPIO_016-GPIO_023 */
110 gpio-line-names =
111 "GPIO-G", /* LSEC pin 29: GPIO
112 "[CSI0_MCLK]", /* HSEC pin 15:
113 "[CSI1_MCLK]", /* HSEC pin 17:
114 "GPIO_019_BT_ACTIVE",
115 "[I2C2_SCL]", /* HSEC pin 32:
116 "[I2C2_SDA]", /* HSEC pin 34:
117 "[I2C3_SCL]", /* HSEC pin 36:
118 "[I2C3_SDA]"; /* HSEC pin 38:
119 };
120
121 &gpio3 {
122 /* GPIO_024-GPIO_031 */
123 gpio-line-names =
124 "GPIO_024_WIFI_ACTIVE",
125 "GPIO_025_PERST_M.2",
126 "[I2C4_SCL]",
127 "[I2C4_SDA]",
128 "NC",
129 "GPIO-H", /* LSEC pin 30: GPIO
130 "[USER_LED1]",
131 "GPIO-L"; /* LSEC pin 34: GPIO
132 };
133
134 &gpio4 {
135 /* GPIO_032-GPIO_039 */
136 gpio-line-names =
137 "GPIO-K", /* LSEC pin 33: GPIO
138 "GPIO_033_PMU1_EN",
139 "GPIO_034_USBSW_SEL",
140 /*
141 * These two pins should be us
142 * to the 96boards specificati
143 * for UART 0. They are howeve
144 */
145 "[SD_DAT1]", /* HSEC pin 3: GP
146 "[SD_DAT2]", /* HSEC pin 5: GP
147 "[UART1_RXD]", /* LSEC pin 13:
148 "[UART1_TXD]", /* LSEC pin 11:
149 "[SOC_GPS_UART3_CTS_N]"; /* TP
150 };
151
152 &gpio5 {
153 /* GPIO_040-GPIO_047 */
154 gpio-line-names =
155 "[SOC_GPS_UART3_RTS_N]", /* TP
156 "[SOC_GPS_UART3_RXD]", /* TP23
157 "[SOC_GPS_UART3_TXD]", /* TP23
158 "[SOC_BT_UART4_CTS_N]",
159 "[SOC_BT_UART4_RTS_N]",
160 "[SOC_BT_UART4_RXD]",
161 "[SOC_BT_UART4_TXD]",
162 "NC";
163 };
164
165 &gpio6 {
166 /* GPIO_048-GPIO_055 */
167 gpio-line-names =
168 "NC",
169 "GPIO_049_USER_LED6",
170 "GPIO_050_CAN_RST",
171 "GPIO_051_WIFI_EN",
172 "GPIO-D", /* LSEC pin 26 */
173 "GPIO-J", /* LSEC pin 32 */
174 "GPIO_054_BT_EN",
175 "[GPIO_055_SEL]";
176 };
177
178 &gpio7 {
179 /* GPIO_056-GPIO_063 */
180 gpio-line-names =
181 "[PCIE_PERST_L]", "NC", "NC",
182 };
183
184 &gpio8 {
185 /* GPIO_064-GPIO_071 */
186 gpio-line-names = "NC", "NC", "NC", "N
187 };
188
189 &gpio9 {
190 /* GPIO_072-GPIO_079 */
191 gpio-line-names = "NC", "NC", "NC", "N
192 };
193
194 &gpio10 {
195 /* GPIO_080-GPIO_087 */
196 gpio-line-names = "NC", "NC", "NC", "N
197 };
198
199 &gpio11 {
200 /* GPIO_088-GPIO_095 */
201 gpio-line-names = "NC", "NC", "NC", "N
202 };
203
204 &gpio12 {
205 /* GPIO_096-GPIO_103 */
206 gpio-line-names = "NC", "", "", "", ""
207 };
208
209 &gpio13 {
210 /* GPIO_104-GPIO_111 */
211 gpio-line-names = "", "", "", "", "",
212 };
213
214 &gpio14 {
215 /* GPIO_112-GPIO_119 */
216 gpio-line-names = "", "", "", "", "",
217 };
218
219 &gpio15 {
220 /* GPIO_120-GPIO_127 */
221 gpio-line-names = "", "", "", "", "",
222 };
223
224 &gpio16 {
225 /* GPIO_128-GPIO_135 */
226 gpio-line-names =
227 "[WL_SDIO_CLK]",
228 "[WL_SDIO_CMD]",
229 "[WL_SDIO_DATA0]",
230 "[WL_SDIO_DATA1]",
231 "[WL_SDIO_DATA2]",
232 "[WL_SDIO_DATA3]",
233 "[ETH_ISOLATE]",
234 "NC";
235 };
236
237 &gpio17 {
238 /* GPIO_136-GPIO_143 */
239 gpio-line-names =
240 "[MINI1CLK_EN]", "NC", "", "",
241 };
242
243 &gpio18 {
244 /* GPIO_144-GPIO_151 */
245 gpio-line-names =
246 "[SPI1_SCLK]", /* HSEC pin 9:
247 "[SPI1_DIN]", /* HSEC pin 11:
248 "[SPI1_DOUT]", /* HSEC pin 1:
249 "[SPI1_CS]", /* HSEC pin 7: GP
250 "[POWER_INT_N]",
251 "[CDMA_GPS_SYNC]",
252 "GPIO_150_PEX_INTA",
253 "GPIO_151_CAN_INT";
254 };
255
256 &gpio19 {
257 /* GPIO_152-GPIO_159 */
258 gpio-line-names = "", "", "", "", "",
259 };
260
261 &gpio20 {
262 /* GPIO_160-GPIO_167 */
263 gpio-line-names =
264 "[SD_CLK]",
265 "[SD_CMD]",
266 "[SD_DATA0]",
267 "[SD_DATA1]",
268 "[SD_DATA2]",
269 "[SD_DATA3]",
270 "GPIO_166_ETHCLK_EN",
271 "GPIO_167_USER_LED2";
272 };
273
274 &gpio21 {
275 /* GPIO_168-GPIO_175 */
276 gpio-line-names =
277 "GPIO_168_GPS_EN",
278 "GPIO-C", /* LSEC pin 25: GPIO
279 "GPIO-E", /* LSEC pin 27: GPIO
280 "GPIO-B", /* LSEC pin 24: GPIO
281 "", "", "", "", "";
282 };
283
284 &gpio22 {
285 /* GPIO_176-GPIO_183 */
286 gpio-line-names =
287 "[PMU_PWR_HOLD]",
288 "GPIO_177_WL_WAKEUP_AP",
289 "[JTAG_TCK]",
290 "[JTAG_TMS]",
291 "[JTAG_TDI]",
292 "[JTAG_TMS]",
293 "GPIO_182_FATAL_ERR",
294 "NC";
295 };
296
297 &gpio23 {
298 /* GPIO_184-GPIO_191 */
299 gpio-line-names =
300 "GPIO_184_JTAG_SEL",
301 "GPIO-F", /* LSEC pin 28: GPIO
302 "[I2C0_SCL]", /* LSEC pin 15:
303 "[I2C0_SDA]", /* LSEC pin 17:
304 "[GPIO_188_I2C1_SCL]", /* Actu
305 "[GPIO_189_I2C1_SDA]", /* Actu
306 "[I2C1_SCL]", /* LSEC pin 19:
307 "[I2C2_SDA]"; /* LSEC pin 21:
308 };
309
310 &gpio24 {
311 /* GPIO_192-GPIO_199 */
312 gpio-line-names =
313 "[SD_LED]",
314 "NC",
315 "[PCM_DI]", /* LSEC pin 22: GP
316 "[PCM_DO]", /* LSEC pin 20: GP
317 "[PCM_CLK]", /* LSEC pin 18: G
318 "[PCM_FS]", /* LSEC pin 16: GP
319 "",
320 "[I2S2_DO]";
321 };
322
323 &gpio25 {
324 /* GPIO_200-GPIO_207 */
325 gpio-line-names =
326 "[I2S2_XCLK]",
327 "[I2S2_XFS]",
328 "GPIO_202_PERST_ETH",
329 "GPIO_203_PWRON_DET",
330 "GPIO_204_PMU1_IRQ_N",
331 "GPIO_205_SD_DET",
332 "GPIO_206_GPS_MOTION_INT",
333 "GPIO_207_HDMI_SEL";
334 };
335
336 &gpio26 {
337 /* GPIO_208-GPIO_215 */
338 gpio-line-names =
339 "GPIO-A", /* LSEC pin 23: GPIO
340 "GPIO_209_VBUS_TYPEC",
341 "NC",
342 "NC",
343 "NC",
344 "[SPI0_SCLK]", /* LSEC pin 8:
345 "[SPI0_DIN]", /* LSEC pin 10:
346 "[SPI0_DOUT]"; /* LSEC pin 14:
347 };
348
349 &gpio27 {
350 /* GPIO_216-GPIO_223 */
351 gpio-line-names =
352 "[SPI0_CS]", /* LSEC pin 12: G
353 "GPIO_217_HDMI_PD",
354 "GPIO_218_GPS_WAKEUP_AP",
355 "GPIO_219_M.2CLK_EN",
356 "GPIO_220_PERST_MINI",
357 "GPIO_221_CC_INT",
358 "[PCIE_CLKREQ_L]",
359 "NC";
360 };
361
362 &gpio28 {
363 /* GPIO_224-GPIO_231 */
364 gpio-line-names =
365 "[PMU0_INT]",
366 "[SPMI_DATA]",
367 "[SPMI_CLK]",
368 "[CAN_SPI_CLK]",
369 "[CAN_SPI_DI]",
370 "[CAN_SPI_DO]",
371 "[CAN_SPI_CS]",
372 "GPIO_231_HDMI_INT";
373 };
374
375 &dwmmc1 {
376 bus-width = <0x4>;
377 sd-uhs-sdr12;
378 sd-uhs-sdr25;
379 sd-uhs-sdr50;
380 sd-uhs-sdr104;
381 cap-sd-highspeed;
382 disable-wp;
383 cd-inverted;
384 cd-gpios = <&gpio25 5 GPIO_ACTIVE_HIGH
385 pinctrl-names = "default";
386 pinctrl-0 = <&sd_pmx_func
387 &sd_clk_cfg_func
388 &sd_cfg_func>;
389 vmmc-supply = <&ldo16>;
390 vqmmc-supply = <&ldo9>;
391 status = "okay";
392 };
393
394 &dwmmc2 { /* WIFI */
395 bus-width = <0x4>;
396 non-removable;
397 broken-cd;
398 cap-power-off-card;
399 pinctrl-names = "default";
400 pinctrl-0 = <&sdio_pmx_func
401 &sdio_clk_cfg_func
402 &sdio_cfg_func>;
403 /* WL_EN */
404 vmmc-supply = <&wlan_en>;
405 status = "okay";
406
407 wlcore: wlcore@2 {
408 compatible = "ti,wl1837";
409 reg = <2>; /* sdio func n
410 /* WL_IRQ, GPIO_177_WL_WAKEUP_
411 interrupt-parent = <&gpio22>;
412 interrupts = <1 IRQ_TYPE_EDGE_
413 };
414 };
415
416 &uart0 {
417 /* On High speed expansion header */
418 label = "HS-UART0";
419 status = "okay";
420 };
421
422 &uart2 {
423 /* On Low speed expansion header */
424 label = "LS-UART0";
425 status = "okay";
426 };
427
428 &uart6 {
429 /* On Low speed expansion header */
430 label = "LS-UART1";
431 status = "okay";
432 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.