1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2 /*
3 * Device Tree file for Marvell Armada 3720 de
4 * (DB-88F3720-DDR3)
5 * Copyright (C) 2016 Marvell
6 *
7 * Gregory CLEMENT <gregory.clement@free-electr
8 *
9 * This file is compatible with the version 1.
10 * the board, however the CON numbers are diff
11 * version
12 */
13
14 /dts-v1/;
15
16 #include <dt-bindings/gpio/gpio.h>
17 #include "armada-372x.dtsi"
18
19 / {
20 model = "Marvell Armada 3720 Developme
21 compatible = "marvell,armada-3720-db",
22
23 chosen {
24 stdout-path = "serial0:115200n
25 };
26
27 memory@0 {
28 device_type = "memory";
29 reg = <0x00000000 0x00000000 0
30 };
31
32 exp_usb3_vbus: usb3-vbus {
33 compatible = "regulator-fixed"
34 regulator-name = "usb3-vbus";
35 regulator-min-microvolt = <500
36 regulator-max-microvolt = <500
37 enable-active-high;
38 regulator-always-on;
39 gpio = <&gpio_exp 1 GPIO_ACTIV
40 };
41
42 usb3_phy: usb3-phy {
43 compatible = "usb-nop-xceiv";
44 vcc-supply = <&exp_usb3_vbus>;
45 };
46
47 vcc_sd_reg1: regulator {
48 compatible = "regulator-gpio";
49 regulator-name = "vcc_sd1";
50 regulator-min-microvolt = <180
51 regulator-max-microvolt = <330
52 regulator-boot-on;
53
54 gpios = <&gpiosb 23 GPIO_ACTIV
55 gpios-states = <0>;
56 states = <1800000 0x1
57 3300000 0x0>;
58 enable-active-high;
59 };
60
61 vcc_sd_reg2: regulator-vmcc {
62 compatible = "regulator-fixed"
63 regulator-name = "vcc_sd2";
64 regulator-min-microvolt = <330
65 regulator-max-microvolt = <330
66 regulator-boot-on;
67 enable-active-high;
68 gpio = <&gpio_exp 4 GPIO_ACTIV
69 };
70 };
71
72 /* Gigabit module on CON19(V2.0)/CON21(V1.4) *
73 ð0 {
74 pinctrl-names = "default";
75 pinctrl-0 = <&rgmii_pins>;
76 phy-mode = "rgmii-id";
77 phy = <&phy0>;
78 status = "okay";
79 };
80
81 /* Gigabit module on CON18(V2.0)/CON20(V1.4) *
82 ð1 {
83 phy-mode = "sgmii";
84 phy = <&phy1>;
85 status = "okay";
86 };
87
88 &i2c0 {
89 pinctrl-names = "default";
90 pinctrl-0 = <&i2c1_pins>;
91 status = "okay";
92
93 gpio_exp: pca9555@22 {
94 compatible = "nxp,pca9555";
95 gpio-controller;
96 #gpio-cells = <2>;
97
98 reg = <0x22>;
99 /*
100 * IO0_0: PWR_EN_USB2 IO1_0:
101 * IO0_1: PWR_EN_USB23 IO1_1:
102 * IO0_2: PWR_EN_SATA IO1_2:
103 * IO0_3: PWR_EN_PCIE IO1_3:
104 * IO0_4: PWR_EN_SD
105 * IO0_5: PWR_EN_EMMC
106 * IO0_6: PWR_EN_RGMII IO1_6:
107 * IO0_7: PWR_EN_SGMII IO1_7:
108 */
109 };
110
111 rtc@68 {
112 /* PT7C4337A from pericom full
113 compatible = "dallas,ds1337";
114 reg = <0x68>;
115 };
116 };
117
118 &mdio {
119 status = "okay";
120 phy0: ethernet-phy@0 {
121 reg = <0>;
122 };
123
124 phy1: ethernet-phy@1 {
125 reg = <1>;
126 };
127 };
128
129 /* CON15(V2.0)/CON17(V1.4) : PCIe / CON15(V2.0
130 &pcie0 {
131 pinctrl-names = "default";
132 pinctrl-0 = <&pcie_reset_pins &pcie_cl
133 reset-gpios = <&gpiosb 3 GPIO_ACTIVE_L
134 status = "okay";
135 };
136
137 /* CON3 */
138 &sata {
139 status = "okay";
140 };
141
142 &sdhci0 {
143 non-removable;
144 bus-width = <8>;
145 mmc-ddr-1_8v;
146 mmc-hs400-1_8v;
147 marvell,pad-type = "fixed-1-8v";
148 status = "okay";
149 };
150
151 /* SD slot module on CON14(V2.0)/CON15(V1.4) *
152 &sdhci1 {
153 wp-inverted;
154 cd-gpios = <&gpiosb 2 GPIO_ACTIVE_LOW>
155 bus-width = <4>;
156 marvell,pad-type = "sd";
157 vqmmc-supply = <&vcc_sd_reg1>;
158 vmmc-supply = <&vcc_sd_reg2>;
159 status = "okay";
160 };
161
162 &spi0 {
163 status = "okay";
164 pinctrl-names = "default";
165 pinctrl-0 = <&spi_quad_pins>;
166
167 flash@0 {
168 compatible = "jedec,spi-nor";
169 reg = <0>;
170 spi-max-frequency = <108000000
171 spi-rx-bus-width = <4>;
172 spi-tx-bus-width = <4>;
173
174 partitions {
175 compatible = "fixed-pa
176 #address-cells = <1>;
177 #size-cells = <1>;
178 partition@0 {
179 label = "bootl
180 reg = <0x0 0x2
181 };
182 partition@200000 {
183 label = "U-boo
184 reg = <0x20000
185 };
186 partition@210000 {
187 label = "Linux
188 reg = <0x21000
189 };
190 };
191 };
192 };
193
194 /*
195 * Exported on the micro USB connector CON30(V
196 * an FTDI (also on CON24(V2.0)/CON26(V1.4)).
197 */
198 &uart0 {
199 pinctrl-names = "default";
200 pinctrl-0 = <&uart1_pins>;
201 status = "okay";
202 };
203
204 /* CON26(V2.0)/CON28(V1.4) */
205 &uart1 {
206 pinctrl-names = "default";
207 pinctrl-0 = <&uart2_pins>;
208 status = "okay";
209 };
210
211 /* CON27(V2.0)/CON29(V1.4) */
212 &usb2 {
213 status = "okay";
214 };
215
216 /* CON29(V2.0)/CON31(V1.4) */
217 &usb3 {
218 status = "okay";
219 usb-phy = <&usb3_phy>;
220 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.