1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Copyright (c) 2014-2016, The Linux Foundati
4 */
5
6 /dts-v1/;
7
8 #include "msm8996.dtsi"
9 #include "pm8994.dtsi"
10 #include "pmi8994.dtsi"
11 #include <dt-bindings/input/input.h>
12 #include <dt-bindings/gpio/gpio.h>
13 #include <dt-bindings/leds/common.h>
14 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h
15 #include <dt-bindings/sound/qcom,q6afe.h>
16 #include <dt-bindings/sound/qcom,q6asm.h>
17 #include <dt-bindings/sound/qcom,wcd9335.h>
18
19 /*
20 * GPIO name legend: proper name = the GPIO li
21 * NC = not connected (pin out bu
22 * anything the board)
23 * "[PER]" = pin is muxed for [periphe
24 * LSEC = Low Speed External Connec
25 * P HSEC = Primary High Speed Extern
26 * S HSEC = Secondary High Speed Exte
27 * J14 = Camera Connector
28 * TP = Test Points
29 *
30 * Line names are taken from the schematic "Dr
31 * drawing no: LM25-P2751-1
32 *
33 * For the lines routed to the external connec
34 * lines are named after the 96Boards CE Speci
35 * Appendix "Expansion Connector Signal Descri
36 *
37 * When the 96Board naming of a line and the s
38 * the same line are in conflict, the 96Board
39 * takes precedence, which means that the exte
40 * LSEC is named UART0 while the schematic and
41 * UART3. This is only for the informational l
42 * the GPIO named lines "GPIO-A" thru "GPIO-L"
43 * ones actually used for GPIO.
44 */
45
46 / {
47 model = "Qualcomm Technologies, Inc. D
48 compatible = "arrow,apq8096-db820c", "
49
50 aliases {
51 serial0 = &blsp2_uart2;
52 serial1 = &blsp2_uart3;
53 serial2 = &blsp1_uart2;
54 i2c0 = &blsp1_i2c3;
55 i2c1 = &blsp2_i2c1;
56 i2c2 = &blsp2_i2c1;
57 spi0 = &blsp1_spi1;
58 spi1 = &blsp2_spi6;
59 };
60
61 chosen {
62 stdout-path = "serial0:115200n
63 };
64
65 div1_mclk: divclk1 {
66 compatible = "gpio-gate-clock"
67 pinctrl-0 = <&audio_mclk>;
68 pinctrl-names = "default";
69 clocks = <&rpmcc RPM_SMD_DIV_C
70 #clock-cells = <0>;
71 enable-gpios = <&pm8994_gpios
72 };
73
74 divclk4: divclk4 {
75 compatible = "fixed-clock";
76 #clock-cells = <0>;
77 clock-frequency = <32768>;
78 clock-output-names = "divclk4"
79
80 pinctrl-names = "default";
81 pinctrl-0 = <&divclk4_pin_a>;
82 };
83
84 gpio-keys {
85 compatible = "gpio-keys";
86 autorepeat;
87
88 pinctrl-names = "default";
89 pinctrl-0 = <&volume_up_gpio>;
90
91 button {
92 label = "Volume Up";
93 linux,code = <KEY_VOLU
94 gpios = <&pm8994_gpios
95 };
96 };
97
98 usb2_id: usb2-id {
99 compatible = "linux,extcon-usb
100 id-gpios = <&pmi8994_gpios 6 G
101 pinctrl-names = "default";
102 pinctrl-0 = <&usb2_vbus_det_gp
103 };
104
105 usb3_id: usb3-id {
106 compatible = "linux,extcon-usb
107 id-gpios = <&pm8994_gpios 22 G
108 pinctrl-names = "default";
109 pinctrl-0 = <&usb3_vbus_det_gp
110 };
111
112 vph_pwr: vph-pwr-regulator {
113 compatible = "regulator-fixed"
114 regulator-name = "vph_pwr";
115 regulator-always-on;
116 regulator-boot-on;
117
118 regulator-min-microvolt = <370
119 regulator-max-microvolt = <370
120 };
121
122 wlan_en: wlan-en-1-8v {
123 pinctrl-names = "default";
124 pinctrl-0 = <&wlan_en_gpios>;
125 compatible = "regulator-fixed"
126 regulator-name = "wlan-en-regu
127 regulator-min-microvolt = <180
128 regulator-max-microvolt = <180
129
130 gpio = <&pm8994_gpios 8 0>;
131
132 /* WLAN card specific delay */
133 startup-delay-us = <70000>;
134 enable-active-high;
135 };
136 };
137
138 &blsp1_i2c3 {
139 /* On Low speed expansion: LS-I2C0 */
140 status = "okay";
141 };
142
143 &blsp1_spi1 {
144 /* On Low speed expansion */
145 status = "okay";
146 };
147
148 &blsp1_uart2 {
149 label = "BT-UART";
150 status = "okay";
151
152 bluetooth {
153 compatible = "qcom,qca6174-bt"
154
155 /* bt_disable_n gpio */
156 enable-gpios = <&pm8994_gpios
157
158 clocks = <&divclk4>;
159 };
160 };
161
162 &adsp_pil {
163 status = "okay";
164 firmware-name = "qcom/apq8096/adsp.mbn
165 };
166
167 &blsp2_i2c1 {
168 /* On High speed expansion: HS-I2C2 */
169 status = "okay";
170 };
171
172 &blsp2_i2c1 {
173 /* On Low speed expansion: LS-I2C1 */
174 status = "okay";
175 };
176
177 &blsp2_spi6 {
178 /* On High speed expansion */
179 status = "okay";
180 };
181
182 &blsp2_uart2 {
183 label = "LS-UART1";
184 status = "okay";
185 pinctrl-names = "default", "sleep";
186 pinctrl-0 = <&blsp2_uart2_2pins_defaul
187 pinctrl-1 = <&blsp2_uart2_2pins_sleep>
188 };
189
190 &blsp2_uart3 {
191 label = "LS-UART0";
192 status = "disabled";
193 pinctrl-names = "default", "sleep";
194 pinctrl-0 = <&blsp2_uart3_4pins_defaul
195 pinctrl-1 = <&blsp2_uart3_4pins_sleep>
196 };
197
198 &camss {
199 vdda-supply = <&vreg_l2a_1p25>;
200 };
201
202 &gpu {
203 status = "okay";
204 };
205
206 &hsusb_phy1 {
207 status = "okay";
208
209 vdd-supply = <&vreg_l28a_0p925>;
210 vdda-pll-supply = <&vreg_l12a_1p8>;
211 vdda-phy-dpdm-supply = <&vreg_l24a_3p0
212 };
213
214 &hsusb_phy2 {
215 status = "okay";
216
217 vdd-supply = <&vreg_l28a_0p925>;
218 vdda-pll-supply = <&vreg_l12a_1p8>;
219 vdda-phy-dpdm-supply = <&vreg_l24a_3p0
220 };
221
222 &mdp {
223 status = "okay";
224 };
225
226 &mdss {
227 status = "okay";
228 };
229
230 &mdss_hdmi {
231 status = "okay";
232
233 pinctrl-names = "default", "sleep";
234 pinctrl-0 = <&hdmi_hpd_active &hdmi_dd
235 pinctrl-1 = <&hdmi_hpd_suspend &hdmi_d
236
237 core-vdda-supply = <&vreg_l12a_1p8>;
238 core-vcc-supply = <&vreg_s4a_1p8>;
239 };
240
241 &mdss_hdmi_phy {
242 status = "okay";
243
244 vddio-supply = <&vreg_l12a_1p8>;
245 vcca-supply = <&vreg_l28a_0p925>;
246 #phy-cells = <0>;
247 };
248
249 &mmcc {
250 vdd-gfx-supply = <&vdd_gfx>;
251 };
252
253 &mss_pil {
254 status = "okay";
255 pll-supply = <&vreg_l12a_1p8>;
256 firmware-name = "qcom/apq8096/mba.mbn"
257 };
258
259 &pm8994_resin {
260 status = "okay";
261 linux,code = <KEY_VOLUMEDOWN>;
262 };
263
264 &tlmm {
265 gpio-line-names =
266 "[SPI0_DOUT]", /* GPIO_0, BLSP
267 "[SPI0_DIN]", /* GPIO_1, BLSP1
268 "[SPI0_CS]", /* GPIO_2, BLSP1_
269 "[SPI0_SCLK]", /* GPIO_3, BLSP
270 "[UART1_TxD]", /* GPIO_4, BLSP
271 "[UART1_RxD]", /* GPIO_5, BLSP
272 "[I2C1_SDA]", /* GPIO_6, BLSP8
273 "[I2C1_SCL]", /* GPIO_7, BLSP8
274 "GPIO-H", /* GPIO_8, LCD0_RESE
275 "TP93", /* GPIO_9 */
276 "GPIO-G", /* GPIO_10, MDP_VSYN
277 "[MDP_VSYNC_S]", /* GPIO_11, S
278 "NC", /* GPIO_12 */
279 "[CSI0_MCLK]", /* GPIO_13, CAM
280 "[CAM_MCLK1]", /* GPIO_14, J14
281 "[CSI1_MCLK]", /* GPIO_15, CAM
282 "TP99", /* GPIO_16 */
283 "[I2C2_SDA]", /* GPIO_17, CCI_
284 "[I2C2_SCL]", /* GPIO_18, CCI_
285 "[CCI_I2C_SDA1]", /* GPIO_19,
286 "[CCI_I2C_SCL1]", /* GPIO_20,
287 "FLASH_STROBE_EN", /* GPIO_21,
288 "FLASH_STROBE_TRIG", /* GPIO_2
289 "GPIO-K", /* GPIO_23, CAM2_RST
290 "GPIO-D", /* GPIO_24, LSEC pin
291 "GPIO-I", /* GPIO_25, CAM0_RST
292 "GPIO-J", /* GPIO_26, CAM0_STA
293 "BLSP6_I2C_SDA", /* GPIO_27 */
294 "BLSP6_I2C_SCL", /* GPIO_28 */
295 "GPIO-B", /* GPIO_29, TS0_RESE
296 "GPIO30", /* GPIO_30, S HSEC p
297 "HDMI_CEC", /* GPIO_31 */
298 "HDMI_DDC_CLOCK", /* GPIO_32 *
299 "HDMI_DDC_DATA", /* GPIO_33 */
300 "HDMI_HOT_PLUG_DETECT", /* GPI
301 "PCIE0_RST_N", /* GPIO_35 */
302 "PCIE0_CLKREQ_N", /* GPIO_36 *
303 "PCIE0_WAKE", /* GPIO_37 */
304 "SD_CARD_DET_N", /* GPIO_38 */
305 "TSIF1_SYNC", /* GPIO_39, S HS
306 "W_DISABLE_N", /* GPIO_40 */
307 "[BLSP9_UART_TX]", /* GPIO_41
308 "[BLSP9_UART_RX]", /* GPIO_42
309 "[BLSP2_UART_CTS_N]", /* GPIO_
310 "[BLSP2_UART_RFR_N]", /* GPIO_
311 "[BLSP3_UART_TX]", /* GPIO_45
312 "[BLSP3_UART_RX]", /* GPIO_46
313 "[I2C0_SDA]", /* GPIO_47, LS_I
314 "[I2C0_SCL]", /* GPIO_48, LS_I
315 "[UART0_TxD]", /* GPIO_49, BLS
316 "[UART0_RxD]", /* GPIO_50, BLS
317 "[UART0_CTS]", /* GPIO_51, BLS
318 "[UART0_RTS]", /* GPIO_52, BLS
319 "[CODEC_INT1_N]", /* GPIO_53 *
320 "[CODEC_INT2_N]", /* GPIO_54 *
321 "[BLSP7_I2C_SDA]", /* GPIO_55
322 "[BLSP7_I2C_SCL]", /* GPIO_56
323 "MI2S_MCLK", /* GPIO_57, S HSE
324 "[PCM_CLK]", /* GPIO_58, QUA_M
325 "[PCM_FS]", /* GPIO_59, QUA_MI
326 "[PCM_DO]", /* GPIO_60, QUA_MI
327 "[PCM_DI]", /* GPIO_61, QUA_MI
328 "GPIO-E", /* GPIO_62, LSEC pin
329 "TP87", /* GPIO_63 */
330 "[CODEC_RST_N]", /* GPIO_64 */
331 "[PCM1_CLK]", /* GPIO_65 */
332 "[PCM1_SYNC]", /* GPIO_66 */
333 "[PCM1_DIN]", /* GPIO_67 */
334 "[PCM1_DOUT]", /* GPIO_68 */
335 "AUDIO_REF_CLK", /* GPIO_69 */
336 "SLIMBUS_CLK", /* GPIO_70 */
337 "SLIMBUS_DATA0", /* GPIO_71 */
338 "SLIMBUS_DATA1", /* GPIO_72 */
339 "NC", /* GPIO_73 */
340 "NC", /* GPIO_74 */
341 "NC", /* GPIO_75 */
342 "NC", /* GPIO_76 */
343 "TP94", /* GPIO_77 */
344 "NC", /* GPIO_78 */
345 "TP95", /* GPIO_79 */
346 "GPIO-A", /* GPIO_80, MEMS_RES
347 "TP88", /* GPIO_81 */
348 "TP89", /* GPIO_82 */
349 "TP90", /* GPIO_83 */
350 "TP91", /* GPIO_84 */
351 "[SD_DAT0]", /* GPIO_85, BLSP1
352 "[SD_CMD]", /* GPIO_86, BLSP12
353 "[SD_DAT3]", /* GPIO_87, BLSP1
354 "[SD_SCLK]", /* GPIO_88, BLSP1
355 "TSIF1_CLK", /* GPIO_89, S HSE
356 "TSIF1_EN", /* GPIO_90, S HSEC
357 "TSIF1_DATA", /* GPIO_91, S HS
358 "NC", /* GPIO_92 */
359 "TSIF2_CLK", /* GPIO_93, S HSE
360 "TSIF2_EN", /* GPIO_94, S HSEC
361 "TSIF2_DATA", /* GPIO_95, S HS
362 "TSIF2_SYNC", /* GPIO_96, S HS
363 "NC", /* GPIO_97 */
364 "CAM1_STANDBY_N", /* GPIO_98 *
365 "NC", /* GPIO_99 */
366 "NC", /* GPIO_100 */
367 "[LCD1_RESET_N]", /* GPIO_101,
368 "BOOT_CONFIG1", /* GPIO_102 */
369 "USB_HUB_RESET", /* GPIO_103 *
370 "CAM1_RST_N", /* GPIO_104 */
371 "NC", /* GPIO_105 */
372 "NC", /* GPIO_106 */
373 "NC", /* GPIO_107 */
374 "NC", /* GPIO_108 */
375 "NC", /* GPIO_109 */
376 "NC", /* GPIO_110 */
377 "NC", /* GPIO_111 */
378 "NC", /* GPIO_112 */
379 "PMI8994_BUA", /* GPIO_113 */
380 "PCIE2_RST_N", /* GPIO_114 */
381 "PCIE2_CLKREQ_N", /* GPIO_115
382 "PCIE2_WAKE", /* GPIO_116 */
383 "SSC_IRQ_0", /* GPIO_117 */
384 "SSC_IRQ_1", /* GPIO_118 */
385 "SSC_IRQ_2", /* GPIO_119 */
386 "NC", /* GPIO_120 */
387 "GPIO121", /* GPIO_121, S HSEC
388 "NC", /* GPIO_122 */
389 "SSC_IRQ_6", /* GPIO_123 */
390 "SSC_IRQ_7", /* GPIO_124 */
391 "GPIO-C", /* GPIO_125, TS_INT0
392 "BOOT_CONFIG5", /* GPIO_126 */
393 "NC", /* GPIO_127 */
394 "NC", /* GPIO_128 */
395 "BOOT_CONFIG7", /* GPIO_129 */
396 "PCIE1_RST_N", /* GPIO_130 */
397 "PCIE1_CLKREQ_N", /* GPIO_131
398 "PCIE1_WAKE", /* GPIO_132 */
399 "GPIO-L", /* GPIO_133, CAM2_ST
400 "NC", /* GPIO_134 */
401 "NC", /* GPIO_135 */
402 "BOOT_CONFIG8", /* GPIO_136 */
403 "NC", /* GPIO_137 */
404 "NC", /* GPIO_138 */
405 "GPS_SSBI2", /* GPIO_139 */
406 "GPS_SSBI1", /* GPIO_140 */
407 "NC", /* GPIO_141 */
408 "NC", /* GPIO_142 */
409 "NC", /* GPIO_143 */
410 "BOOT_CONFIG6", /* GPIO_144 */
411 "NC", /* GPIO_145 */
412 "NC", /* GPIO_146 */
413 "NC", /* GPIO_147 */
414 "NC", /* GPIO_148 */
415 "NC"; /* GPIO_149 */
416
417 sdc2_cd_on: sdc2-cd-on-state {
418 pins = "gpio38";
419 function = "gpio";
420 bias-pull-up;
421 drive-strength = <16>;
422 };
423
424 sdc2_cd_off: sdc2-cd-off-state {
425 pins = "gpio38";
426 function = "gpio";
427 bias-pull-up;
428 drive-strength = <2>;
429 };
430
431 hdmi_hpd_active: hdmi-hpd-active-state
432 pins = "gpio34";
433 function = "hdmi_hot";
434 bias-pull-down;
435 drive-strength = <16>;
436 };
437
438 hdmi_hpd_suspend: hdmi-hpd-suspend-sta
439 pins = "gpio34";
440 function = "hdmi_hot";
441 bias-pull-down;
442 drive-strength = <2>;
443 };
444
445 hdmi_ddc_active: hdmi-ddc-active-state
446 pins = "gpio32", "gpio33";
447 function = "hdmi_ddc";
448 drive-strength = <2>;
449 bias-pull-up;
450 };
451
452 hdmi_ddc_suspend: hdmi-ddc-suspend-sta
453 pins = "gpio32", "gpio33";
454 function = "hdmi_ddc";
455 drive-strength = <2>;
456 bias-pull-down;
457 };
458 };
459
460 &pcie0 {
461 status = "okay";
462 perst-gpios = <&tlmm 35 GPIO_ACTIVE_LO
463 vddpe-3v3-supply = <&wlan_en>;
464 vdda-supply = <&vreg_l28a_0p925>;
465 };
466
467 &pcie1 {
468 status = "okay";
469 perst-gpios = <&tlmm 130 GPIO_ACTIVE_L
470 vdda-supply = <&vreg_l28a_0p925>;
471 };
472
473 &pcie2 {
474 status = "okay";
475 perst-gpios = <&tlmm 114 GPIO_ACTIVE_L
476 vdda-supply = <&vreg_l28a_0p925>;
477 };
478
479 &pcie_phy {
480 status = "okay";
481
482 vdda-phy-supply = <&vreg_l28a_0p925>;
483 vdda-pll-supply = <&vreg_l12a_1p8>;
484 };
485
486 &pm8994_gpios {
487 gpio-line-names =
488 "NC",
489 "KEY_VOLP_N",
490 "NC",
491 "BL1_PWM",
492 "GPIO-F", /* BL0_PWM, LSEC pin
493 "BL1_EN",
494 "NC",
495 "WLAN_EN",
496 "NC",
497 "NC",
498 "NC",
499 "NC",
500 "NC",
501 "NC",
502 "DIVCLK1",
503 "DIVCLK2",
504 "DIVCLK3",
505 "DIVCLK4",
506 "BT_EN",
507 "PMIC_SLB",
508 "PMIC_BUA",
509 "USB_VBUS_DET";
510
511 pinctrl-names = "default";
512 pinctrl-0 = <&ls_exp_gpio_f &bt_en_gpi
513
514 ls_exp_gpio_f: pm8994-gpio5-state {
515 pinconf {
516 pins = "gpio5";
517 function = PMIC_GPIO_F
518 output-low;
519 power-source = <PM8994
520 };
521 };
522
523 bt_en_gpios: bt-en-pios-state {
524 pinconf {
525 pins = "gpio19";
526 function = PMIC_GPIO_F
527 output-low;
528 power-source = <PM8994
529 qcom,drive-strength =
530 bias-pull-down;
531 };
532 };
533
534 wlan_en_gpios: wlan-en-gpios-state {
535 pinconf {
536 pins = "gpio8";
537 function = PMIC_GPIO_F
538 output-low;
539 power-source = <PM8994
540 qcom,drive-strength =
541 bias-pull-down;
542 };
543 };
544
545 audio_mclk: clk-div1-state {
546 pinconf {
547 pins = "gpio15";
548 function = "func1";
549 power-source = <PM8994
550 };
551 };
552
553 volume_up_gpio: pm8996-gpio2-state {
554 pinconf {
555 pins = "gpio2";
556 function = "normal";
557 input-enable;
558 drive-push-pull;
559 bias-pull-up;
560 qcom,drive-strength =
561 power-source = <PM8994
562 };
563 };
564
565 divclk4_pin_a: divclk4-state {
566 pinconf {
567 pins = "gpio18";
568 function = PMIC_GPIO_F
569
570 bias-disable;
571 power-source = <PM8994
572 };
573 };
574
575 usb3_vbus_det_gpio: pm8996-gpio22-stat
576 pinconf {
577 pins = "gpio22";
578 function = PMIC_GPIO_F
579 input-enable;
580 bias-pull-down;
581 qcom,drive-strength =
582 power-source = <PM8994
583 };
584 };
585 };
586
587 &pm8994_mpps {
588 gpio-line-names =
589 "VDDPX_BIAS",
590 "WIFI_LED",
591 "NC",
592 "BT_LED",
593 "PM_MPP05",
594 "PM_MPP06",
595 "PM_MPP07",
596 "NC";
597 };
598
599 &pm8994_spmi_regulators {
600 qcom,saw-reg = <&saw3>;
601 vdd_s11-supply = <&vph_pwr>;
602
603 s9 {
604 qcom,saw-slave;
605 };
606 s10 {
607 qcom,saw-slave;
608 };
609 s11 {
610 qcom,saw-leader;
611 regulator-name = "VDD_APCC";
612 regulator-always-on;
613 regulator-min-microvolt = <980
614 regulator-max-microvolt = <980
615 };
616 };
617
618 &pmi8994_gpios {
619 gpio-line-names =
620 "NC",
621 "SPKR_AMP_EN1",
622 "SPKR_AMP_EN2",
623 "TP61",
624 "NC",
625 "USB2_VBUS_DET",
626 "NC",
627 "NC",
628 "NC",
629 "NC";
630
631 usb2_vbus_det_gpio: pmi8996-gpio6-stat
632 pinconf {
633 pins = "gpio6";
634 function = PMIC_GPIO_F
635 input-enable;
636 bias-pull-down;
637 qcom,drive-strength =
638 power-source = <PM8994
639 };
640 };
641 };
642
643 &pmi8994_lpg {
644 qcom,power-source = <1>;
645
646 pinctrl-names = "default";
647 pinctrl-0 = <&pmi8994_mpp2_userled4>;
648
649 qcom,dtest = <0 0>,
650 <0 0>,
651 <0 0>,
652 <4 1>;
653
654 status = "okay";
655
656 led@1 {
657 reg = <1>;
658 color = <LED_COLOR_ID_GREEN>;
659 function = LED_FUNCTION_HEARTB
660 function-enumerator = <1>;
661
662 linux,default-trigger = "heart
663 default-state = "on";
664 };
665
666 led@2 {
667 reg = <2>;
668 color = <LED_COLOR_ID_GREEN>;
669 function = LED_FUNCTION_HEARTB
670 function-enumerator = <0>;
671 };
672
673 led@3 {
674 reg = <3>;
675 color = <LED_COLOR_ID_GREEN>;
676 function = LED_FUNCTION_HEARTB
677 function-enumerator = <2>;
678 };
679
680 led@4 {
681 reg = <4>;
682 color = <LED_COLOR_ID_GREEN>;
683 function = LED_FUNCTION_HEARTB
684 function-enumerator = <3>;
685 };
686 };
687
688 &pmi8994_mpps {
689 pmi8994_mpp2_userled4: mpp2-userled4-s
690 pins = "mpp2";
691 function = "sink";
692
693 output-low;
694 qcom,dtest = <4>;
695 };
696 };
697
698 &pmi8994_spmi_regulators {
699 vdd_s2-supply = <&vph_pwr>;
700
701 vdd_gfx: s2 {
702 regulator-name = "VDD_GFX";
703 regulator-min-microvolt = <980
704 regulator-max-microvolt = <980
705 };
706 };
707
708 &rpm_requests {
709 regulators-0 {
710 compatible = "qcom,rpm-pm8994-
711
712 vdd_s1-supply = <&vph_pwr>;
713 vdd_s2-supply = <&vph_pwr>;
714 vdd_s3-supply = <&vph_pwr>;
715 vdd_s4-supply = <&vph_pwr>;
716 vdd_s5-supply = <&vph_pwr>;
717 vdd_s6-supply = <&vph_pwr>;
718 vdd_s7-supply = <&vph_pwr>;
719 vdd_s8-supply = <&vph_pwr>;
720 vdd_s9-supply = <&vph_pwr>;
721 vdd_s10-supply = <&vph_pwr>;
722 vdd_s11-supply = <&vph_pwr>;
723 vdd_s12-supply = <&vph_pwr>;
724 vdd_l1-supply = <&vreg_s1b_1p0
725 vdd_l2_l26_l28-supply = <&vreg
726 vdd_l3_l11-supply = <&vreg_s3a
727 vdd_l4_l27_l31-supply = <&vreg
728 vdd_l5_l7-supply = <&vreg_s5a_
729 vdd_l6_l12_l32-supply = <&vreg
730 vdd_l8_l16_l30-supply = <&vph_
731 vdd_l9_l10_l18_l22-supply = <&
732 vdd_l13_l19_l23_l24-supply = <
733 vdd_l14_l15-supply = <&vreg_s5
734 vdd_l17_l29-supply = <&vph_pwr
735 vdd_l20_l21-supply = <&vph_pwr
736 vdd_l25-supply = <&vreg_s3a_1p
737 vdd_lvs1_2-supply = <&vreg_s4a
738
739 vreg_s3a_1p3: s3 {
740 regulator-name = "vreg
741 regulator-min-microvol
742 regulator-max-microvol
743 };
744
745 /**
746 * 1.8v required on LS expansi
747 * for mezzanine boards
748 */
749 vreg_s4a_1p8: s4 {
750 regulator-name = "vreg
751 regulator-min-microvol
752 regulator-max-microvol
753 regulator-always-on;
754 };
755 vreg_s5a_2p15: s5 {
756 regulator-name = "vreg
757 regulator-min-microvol
758 regulator-max-microvol
759 };
760 vreg_s7a_1p0: s7 {
761 regulator-name = "vreg
762 regulator-min-microvol
763 regulator-max-microvol
764 };
765
766 vreg_l1a_1p0: l1 {
767 regulator-name = "vreg
768 regulator-min-microvol
769 regulator-max-microvol
770 };
771 vreg_l2a_1p25: l2 {
772 regulator-name = "vreg
773 regulator-min-microvol
774 regulator-max-microvol
775 };
776 vreg_l3a_0p875: l3 {
777 regulator-name = "vreg
778 regulator-min-microvol
779 regulator-max-microvol
780 };
781 vreg_l4a_1p225: l4 {
782 regulator-name = "vreg
783 regulator-min-microvol
784 regulator-max-microvol
785 };
786 vreg_l6a_1p2: l6 {
787 regulator-name = "vreg
788 regulator-min-microvol
789 regulator-max-microvol
790 };
791 vreg_l8a_1p8: l8 {
792 regulator-name = "vreg
793 regulator-min-microvol
794 regulator-max-microvol
795 };
796 vreg_l9a_1p8: l9 {
797 regulator-name = "vreg
798 regulator-min-microvol
799 regulator-max-microvol
800 };
801 vreg_l10a_1p8: l10 {
802 regulator-name = "vreg
803 regulator-min-microvol
804 regulator-max-microvol
805 };
806 vreg_l11a_1p15: l11 {
807 regulator-name = "vreg
808 regulator-min-microvol
809 regulator-max-microvol
810 };
811 vreg_l12a_1p8: l12 {
812 regulator-name = "vreg
813 regulator-min-microvol
814 regulator-max-microvol
815 };
816 vreg_l13a_2p95: l13 {
817 regulator-name = "vreg
818 regulator-min-microvol
819 regulator-max-microvol
820 };
821 vreg_l14a_1p8: l14 {
822 regulator-name = "vreg
823 regulator-min-microvol
824 regulator-max-microvol
825 };
826 vreg_l15a_1p8: l15 {
827 regulator-name = "vreg
828 regulator-min-microvol
829 regulator-max-microvol
830 };
831 vreg_l16a_2p7: l16 {
832 regulator-name = "vreg
833 regulator-min-microvol
834 regulator-max-microvol
835 };
836 vreg_l17a_2p8: l17 {
837 regulator-name = "vreg
838 regulator-min-microvol
839 regulator-max-microvol
840 };
841 vreg_l18a_2p85: l18 {
842 regulator-name = "vreg
843 regulator-min-microvol
844 regulator-max-microvol
845 };
846 vreg_l19a_2p8: l19 {
847 regulator-name = "vreg
848 regulator-min-microvol
849 regulator-max-microvol
850 };
851 vreg_l20a_2p95: l20 {
852 regulator-name = "vreg
853 regulator-min-microvol
854 regulator-max-microvol
855 regulator-allow-set-lo
856 };
857 vreg_l21a_2p95: l21 {
858 regulator-name = "vreg
859 regulator-min-microvol
860 regulator-max-microvol
861 regulator-allow-set-lo
862 regulator-system-load
863 };
864 vreg_l22a_3p0: l22 {
865 regulator-name = "vreg
866 regulator-min-microvol
867 regulator-max-microvol
868 };
869 vreg_l23a_2p8: l23 {
870 regulator-name = "vreg
871 regulator-min-microvol
872 regulator-max-microvol
873 };
874 vreg_l24a_3p075: l24 {
875 regulator-name = "vreg
876 regulator-min-microvol
877 regulator-max-microvol
878 };
879 vreg_l25a_1p2: l25 {
880 regulator-name = "vreg
881 regulator-min-microvol
882 regulator-max-microvol
883 regulator-allow-set-lo
884 };
885 vreg_l26a_0p8: l27 {
886 regulator-name = "vreg
887 regulator-min-microvol
888 regulator-max-microvol
889 };
890 vreg_l28a_0p925: l28 {
891 regulator-name = "vreg
892 regulator-min-microvol
893 regulator-max-microvol
894 regulator-allow-set-lo
895 };
896 vreg_l29a_2p8: l29 {
897 regulator-name = "vreg
898 regulator-min-microvol
899 regulator-max-microvol
900 };
901 vreg_l30a_1p8: l30 {
902 regulator-name = "vreg
903 regulator-min-microvol
904 regulator-max-microvol
905 };
906 vreg_l32a_1p8: l32 {
907 regulator-name = "vreg
908 regulator-min-microvol
909 regulator-max-microvol
910 };
911
912 vreg_lvs1a_1p8: lvs1 {
913 regulator-name = "vreg
914 };
915
916 vreg_lvs2a_1p8: lvs2 {
917 regulator-name = "vreg
918 };
919 };
920
921 regulators-1 {
922 compatible = "qcom,rpm-pmi8994
923
924 vdd_s1-supply = <&vph_pwr>;
925 vdd_s2-supply = <&vph_pwr>;
926 vdd_s3-supply = <&vph_pwr>;
927 vdd_bst_byp-supply = <&vph_pwr
928
929 vph_pwr_bbyp: boost-bypass {
930 regulator-name = "vph_
931 regulator-min-microvol
932 regulator-max-microvol
933 };
934
935 vreg_s1b_1p025: s1 {
936 regulator-name = "vreg
937 regulator-min-microvol
938 regulator-max-microvol
939 };
940 };
941 };
942
943 &sdhc2 {
944 /* External SD card */
945 pinctrl-names = "default", "sleep";
946 pinctrl-0 = <&sdc2_state_on &sdc2_cd_o
947 pinctrl-1 = <&sdc2_state_off &sdc2_cd_
948 cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
949 vmmc-supply = <&vreg_l21a_2p95>;
950 vqmmc-supply = <&vreg_l13a_2p95>;
951 status = "okay";
952 };
953
954 &q6asmdai {
955 dai@0 {
956 reg = <0>;
957 };
958
959 dai@1 {
960 reg = <1>;
961 };
962
963 dai@2 {
964 reg = <2>;
965 };
966 };
967
968 &slim_msm {
969 status = "okay";
970
971 slim@1 {
972 reg = <1>;
973 #address-cells = <2>;
974 #size-cells = <0>;
975
976 tasha_ifd: tas-ifd@0,0 {
977 compatible = "slim217,
978 reg = <0 0>;
979 };
980
981 wcd9335: codec@1,0 {
982 compatible = "slim217,
983 reg = <1 0>;
984
985 clock-names = "mclk",
986 clocks = <&div1_mclk>,
987 <&rpmcc RPM_S
988 interrupt-parent = <&t
989 interrupts = <54 IRQ_T
990 <53 IRQ_T
991 interrupt-names = "int
992 interrupt-controller;
993 #interrupt-cells = <1>
994
995 pinctrl-0 = <&cdc_rese
996 pinctrl-names = "defau
997
998 reset-gpios = <&tlmm 6
999 slim-ifc-dev = <&tasha
1000
1001 #sound-dai-cells = <1
1002
1003 vdd-buck-supply = <&v
1004 vdd-buck-sido-supply
1005 vdd-tx-supply = <&vre
1006 vdd-rx-supply = <&vre
1007 vdd-io-supply = <&vre
1008 };
1009 };
1010 };
1011
1012 &sound {
1013 compatible = "qcom,apq8096-sndcard";
1014 model = "DB820c";
1015 audio-routing = "RX_BIAS", "MCLK",
1016 "MM_DL1", "MultiMedia1 Playb
1017 "MM_DL2", "MultiMedia2 Playb
1018 "MultiMedia3 Capture", "MM_UL
1019
1020 mm1-dai-link {
1021 link-name = "MultiMedia1";
1022 cpu {
1023 sound-dai = <&q6asmda
1024 };
1025 };
1026
1027 mm2-dai-link {
1028 link-name = "MultiMedia2";
1029 cpu {
1030 sound-dai = <&q6asmda
1031 };
1032 };
1033
1034 mm3-dai-link {
1035 link-name = "MultiMedia3";
1036 cpu {
1037 sound-dai = <&q6asmda
1038 };
1039 };
1040
1041 hdmi-dai-link {
1042 link-name = "HDMI";
1043 cpu {
1044 sound-dai = <&q6afeda
1045 };
1046
1047 platform {
1048 sound-dai = <&q6routi
1049 };
1050
1051 codec {
1052 sound-dai = <&mdss_hd
1053 };
1054 };
1055
1056 slim-dai-link {
1057 link-name = "SLIM Playback";
1058 cpu {
1059 sound-dai = <&q6afeda
1060 };
1061
1062 platform {
1063 sound-dai = <&q6routi
1064 };
1065
1066 codec {
1067 sound-dai = <&wcd9335
1068 };
1069 };
1070
1071 slimcap-dai-link {
1072 link-name = "SLIM Capture";
1073 cpu {
1074 sound-dai = <&q6afeda
1075 };
1076
1077 platform {
1078 sound-dai = <&q6routi
1079 };
1080
1081 codec {
1082 sound-dai = <&wcd9335
1083 };
1084 };
1085 };
1086
1087 &ufsphy {
1088 status = "okay";
1089
1090 vdda-phy-supply = <&vreg_l28a_0p925>;
1091 vdda-pll-supply = <&vreg_l12a_1p8>;
1092 };
1093
1094 &ufshc {
1095 status = "okay";
1096
1097 vcc-supply = <&vreg_l20a_2p95>;
1098 vccq-supply = <&vreg_l25a_1p2>;
1099 vccq2-supply = <&vreg_s4a_1p8>;
1100 vdd-hba-supply = <&vreg_l25a_1p2>;
1101
1102 vcc-max-microamp = <600000>;
1103 vccq-max-microamp = <450000>;
1104 vccq2-max-microamp = <450000>;
1105 };
1106
1107 &usb2 {
1108 status = "okay";
1109 extcon = <&usb2_id>;
1110 };
1111
1112 &usb2_dwc3 {
1113 extcon = <&usb2_id>;
1114 dr_mode = "otg";
1115 maximum-speed = "high-speed";
1116 };
1117
1118 &usb3 {
1119 status = "okay";
1120 extcon = <&usb3_id>;
1121 };
1122
1123 &usb3_dwc3 {
1124 extcon = <&usb3_id>;
1125 dr_mode = "otg";
1126 };
1127
1128 &usb3phy {
1129 status = "okay";
1130
1131 vdda-phy-supply = <&vreg_l28a_0p925>;
1132 vdda-pll-supply = <&vreg_l12a_1p8>;
1133 };
1134
1135 &venus {
1136 status = "okay";
1137 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.