1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT) 1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2 /* 2 /*
3 * Copyright (c) 2017 T-Chip Intelligent Techn 3 * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
4 */ 4 */
5 5
6 /dts-v1/; 6 /dts-v1/;
7 #include "rk3399-roc-pc.dtsi" !! 7 #include <dt-bindings/pwm/pwm.h>
>> 8 #include "rk3399.dtsi"
>> 9 #include "rk3399-opp.dtsi"
8 10
9 / { 11 / {
10 model = "Firefly ROC-RK3399-PC Board"; 12 model = "Firefly ROC-RK3399-PC Board";
11 compatible = "firefly,roc-rk3399-pc", 13 compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399";
>> 14
>> 15 chosen {
>> 16 stdout-path = "serial2:1500000n8";
>> 17 };
>> 18
>> 19 backlight: backlight {
>> 20 compatible = "pwm-backlight";
>> 21 pwms = <&pwm0 0 25000 0>;
>> 22 };
>> 23
>> 24 clkin_gmac: external-gmac-clock {
>> 25 compatible = "fixed-clock";
>> 26 clock-frequency = <125000000>;
>> 27 clock-output-names = "clkin_gmac";
>> 28 #clock-cells = <0>;
>> 29 };
>> 30
>> 31 sdio_pwrseq: sdio-pwrseq {
>> 32 compatible = "mmc-pwrseq-simple";
>> 33 clocks = <&rk808 1>;
>> 34 clock-names = "ext_clock";
>> 35 pinctrl-names = "default";
>> 36 pinctrl-0 = <&wifi_enable_h>;
>> 37
>> 38 /*
>> 39 * On the module itself this is one of these (depending
>> 40 * on the actual card populated):
>> 41 * - SDIO_RESET_L_WL_REG_ON
>> 42 * - PDN (power down when low)
>> 43 */
>> 44 reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
>> 45 };
>> 46
>> 47 vcc_vbus_typec0: vcc-vbus-typec0 {
>> 48 compatible = "regulator-fixed";
>> 49 regulator-name = "vcc_vbus_typec0";
>> 50 regulator-always-on;
>> 51 regulator-boot-on;
>> 52 regulator-min-microvolt = <5000000>;
>> 53 regulator-max-microvolt = <5000000>;
>> 54 };
>> 55
>> 56 /*
>> 57 * should be placed inside mp8859, but not until mp8859 has
>> 58 * its own dt-binding.
>> 59 */
>> 60 vcc12v_sys: mp8859-dcdc1 {
>> 61 compatible = "regulator-fixed";
>> 62 regulator-name = "vcc12v_sys";
>> 63 regulator-always-on;
>> 64 regulator-boot-on;
>> 65 regulator-min-microvolt = <12000000>;
>> 66 regulator-max-microvolt = <12000000>;
>> 67 vin-supply = <&vcc_vbus_typec0>;
>> 68 };
>> 69
>> 70 /* switched by pmic_sleep */
>> 71 vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
>> 72 compatible = "regulator-fixed";
>> 73 regulator-name = "vcc1v8_s3";
>> 74 regulator-always-on;
>> 75 regulator-boot-on;
>> 76 regulator-min-microvolt = <1800000>;
>> 77 regulator-max-microvolt = <1800000>;
>> 78 vin-supply = <&vcc_1v8>;
>> 79 };
>> 80
>> 81 vcc3v3_sys: vcc3v3-sys {
>> 82 compatible = "regulator-fixed";
>> 83 regulator-name = "vcc3v3_sys";
>> 84 regulator-always-on;
>> 85 regulator-boot-on;
>> 86 regulator-min-microvolt = <3300000>;
>> 87 regulator-max-microvolt = <3300000>;
>> 88 vin-supply = <&vcc12v_sys>;
>> 89 };
>> 90
>> 91 /* Actually 3 regulators (host0, 1, 2) controlled by the same gpio */
>> 92 vcc5v0_host: vcc5v0-host-regulator {
>> 93 compatible = "regulator-fixed";
>> 94 enable-active-high;
>> 95 gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
>> 96 pinctrl-names = "default";
>> 97 pinctrl-0 = <&vcc5v0_host_en &hub_rst>;
>> 98 regulator-name = "vcc5v0_host";
>> 99 regulator-always-on;
>> 100 vin-supply = <&vcc_sys>;
>> 101 };
>> 102
>> 103 vcc_vbus_typec1: vcc-vbus-typec1 {
>> 104 compatible = "regulator-fixed";
>> 105 enable-active-high;
>> 106 gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
>> 107 pinctrl-names = "default";
>> 108 pinctrl-0 = <&vcc_vbus_typec1_en>;
>> 109 regulator-name = "vcc_vbus_typec1";
>> 110 regulator-always-on;
>> 111 vin-supply = <&vcc_sys>;
>> 112 };
>> 113
>> 114 vcc_sys: vcc-sys {
>> 115 compatible = "regulator-fixed";
>> 116 regulator-name = "vcc_sys";
>> 117 regulator-always-on;
>> 118 regulator-boot-on;
>> 119 regulator-min-microvolt = <5000000>;
>> 120 regulator-max-microvolt = <5000000>;
>> 121 vin-supply = <&vcc12v_sys>;
>> 122 };
>> 123
>> 124 vdd_log: vdd-log {
>> 125 compatible = "pwm-regulator";
>> 126 pwms = <&pwm2 0 25000 1>;
>> 127 regulator-name = "vdd_log";
>> 128 regulator-always-on;
>> 129 regulator-boot-on;
>> 130 regulator-min-microvolt = <800000>;
>> 131 regulator-max-microvolt = <1400000>;
>> 132 vin-supply = <&vcc3v3_sys>;
>> 133 };
>> 134 };
>> 135
>> 136 &cpu_l0 {
>> 137 cpu-supply = <&vdd_cpu_l>;
>> 138 };
>> 139
>> 140 &cpu_l1 {
>> 141 cpu-supply = <&vdd_cpu_l>;
>> 142 };
>> 143
>> 144 &cpu_l2 {
>> 145 cpu-supply = <&vdd_cpu_l>;
>> 146 };
>> 147
>> 148 &cpu_l3 {
>> 149 cpu-supply = <&vdd_cpu_l>;
>> 150 };
>> 151
>> 152 &cpu_b0 {
>> 153 cpu-supply = <&vdd_cpu_b>;
>> 154 };
>> 155
>> 156 &cpu_b1 {
>> 157 cpu-supply = <&vdd_cpu_b>;
>> 158 };
>> 159
>> 160 &emmc_phy {
>> 161 status = "okay";
>> 162 };
>> 163
>> 164 &gmac {
>> 165 assigned-clocks = <&cru SCLK_RMII_SRC>;
>> 166 assigned-clock-parents = <&clkin_gmac>;
>> 167 clock_in_out = "input";
>> 168 phy-supply = <&vcc_lan>;
>> 169 phy-mode = "rgmii";
>> 170 pinctrl-names = "default";
>> 171 pinctrl-0 = <&rgmii_pins>;
>> 172 snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
>> 173 snps,reset-active-low;
>> 174 snps,reset-delays-us = <0 10000 50000>;
>> 175 tx_delay = <0x28>;
>> 176 rx_delay = <0x11>;
>> 177 status = "okay";
>> 178 };
>> 179
>> 180 &hdmi {
>> 181 ddc-i2c-bus = <&i2c3>;
>> 182 pinctrl-names = "default";
>> 183 pinctrl-0 = <&hdmi_cec>;
>> 184 status = "okay";
>> 185 };
>> 186
>> 187 &i2c0 {
>> 188 clock-frequency = <400000>;
>> 189 i2c-scl-rising-time-ns = <168>;
>> 190 i2c-scl-falling-time-ns = <4>;
>> 191 status = "okay";
>> 192
>> 193 rk808: pmic@1b {
>> 194 compatible = "rockchip,rk808";
>> 195 reg = <0x1b>;
>> 196 interrupt-parent = <&gpio1>;
>> 197 interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
>> 198 #clock-cells = <1>;
>> 199 clock-output-names = "xin32k", "rk808-clkout2";
>> 200 pinctrl-names = "default";
>> 201 pinctrl-0 = <&pmic_int_l>;
>> 202 rockchip,system-power-controller;
>> 203 wakeup-source;
>> 204
>> 205 vcc1-supply = <&vcc3v3_sys>;
>> 206 vcc2-supply = <&vcc3v3_sys>;
>> 207 vcc3-supply = <&vcc3v3_sys>;
>> 208 vcc4-supply = <&vcc3v3_sys>;
>> 209 vcc6-supply = <&vcc3v3_sys>;
>> 210 vcc7-supply = <&vcc3v3_sys>;
>> 211 vcc8-supply = <&vcc3v3_sys>;
>> 212 vcc9-supply = <&vcc3v3_sys>;
>> 213 vcc10-supply = <&vcc3v3_sys>;
>> 214 vcc11-supply = <&vcc3v3_sys>;
>> 215 vcc12-supply = <&vcc3v3_sys>;
>> 216 vddio-supply = <&vcc1v8_pmu>;
>> 217
>> 218 regulators {
>> 219 vdd_center: DCDC_REG1 {
>> 220 regulator-name = "vdd_center";
>> 221 regulator-always-on;
>> 222 regulator-boot-on;
>> 223 regulator-min-microvolt = <750000>;
>> 224 regulator-max-microvolt = <1350000>;
>> 225 regulator-ramp-delay = <6001>;
>> 226 regulator-state-mem {
>> 227 regulator-off-in-suspend;
>> 228 };
>> 229 };
>> 230
>> 231 vdd_cpu_l: DCDC_REG2 {
>> 232 regulator-name = "vdd_cpu_l";
>> 233 regulator-always-on;
>> 234 regulator-boot-on;
>> 235 regulator-min-microvolt = <750000>;
>> 236 regulator-max-microvolt = <1350000>;
>> 237 regulator-ramp-delay = <6001>;
>> 238 regulator-state-mem {
>> 239 regulator-off-in-suspend;
>> 240 };
>> 241 };
>> 242
>> 243 vcc_ddr: DCDC_REG3 {
>> 244 regulator-name = "vcc_ddr";
>> 245 regulator-always-on;
>> 246 regulator-boot-on;
>> 247 regulator-state-mem {
>> 248 regulator-on-in-suspend;
>> 249 };
>> 250 };
>> 251
>> 252 vcc_1v8: DCDC_REG4 {
>> 253 regulator-name = "vcc_1v8";
>> 254 regulator-always-on;
>> 255 regulator-boot-on;
>> 256 regulator-min-microvolt = <1800000>;
>> 257 regulator-max-microvolt = <1800000>;
>> 258 regulator-state-mem {
>> 259 regulator-on-in-suspend;
>> 260 regulator-suspend-microvolt = <1800000>;
>> 261 };
>> 262 };
>> 263
>> 264 vcca1v8_codec: LDO_REG1 {
>> 265 regulator-name = "vcca1v8_codec";
>> 266 regulator-always-on;
>> 267 regulator-boot-on;
>> 268 regulator-min-microvolt = <1800000>;
>> 269 regulator-max-microvolt = <1800000>;
>> 270 regulator-state-mem {
>> 271 regulator-off-in-suspend;
>> 272 };
>> 273 };
>> 274
>> 275 vcc1v8_hdmi: LDO_REG2 {
>> 276 regulator-name = "vcc1v8_hdmi";
>> 277 regulator-always-on;
>> 278 regulator-boot-on;
>> 279 regulator-min-microvolt = <1800000>;
>> 280 regulator-max-microvolt = <1800000>;
>> 281 regulator-state-mem {
>> 282 regulator-off-in-suspend;
>> 283 };
>> 284 };
>> 285
>> 286 vcc1v8_pmu: LDO_REG3 {
>> 287 regulator-name = "vcc1v8_pmu";
>> 288 regulator-always-on;
>> 289 regulator-boot-on;
>> 290 regulator-min-microvolt = <1800000>;
>> 291 regulator-max-microvolt = <1800000>;
>> 292 regulator-state-mem {
>> 293 regulator-on-in-suspend;
>> 294 regulator-suspend-microvolt = <1800000>;
>> 295 };
>> 296 };
>> 297
>> 298 vcc_sdio: LDO_REG4 {
>> 299 regulator-name = "vcc_sdio";
>> 300 regulator-always-on;
>> 301 regulator-boot-on;
>> 302 regulator-min-microvolt = <1800000>;
>> 303 regulator-max-microvolt = <3000000>;
>> 304 regulator-state-mem {
>> 305 regulator-on-in-suspend;
>> 306 regulator-suspend-microvolt = <3000000>;
>> 307 };
>> 308 };
>> 309
>> 310 vcca3v0_codec: LDO_REG5 {
>> 311 regulator-name = "vcca3v0_codec";
>> 312 regulator-always-on;
>> 313 regulator-boot-on;
>> 314 regulator-min-microvolt = <3000000>;
>> 315 regulator-max-microvolt = <3000000>;
>> 316 regulator-state-mem {
>> 317 regulator-off-in-suspend;
>> 318 };
>> 319 };
>> 320
>> 321 vcc_1v5: LDO_REG6 {
>> 322 regulator-name = "vcc_1v5";
>> 323 regulator-always-on;
>> 324 regulator-boot-on;
>> 325 regulator-min-microvolt = <1500000>;
>> 326 regulator-max-microvolt = <1500000>;
>> 327 regulator-state-mem {
>> 328 regulator-on-in-suspend;
>> 329 regulator-suspend-microvolt = <1500000>;
>> 330 };
>> 331 };
>> 332
>> 333 vcca0v9_hdmi: LDO_REG7 {
>> 334 regulator-name = "vcca0v9_hdmi";
>> 335 regulator-always-on;
>> 336 regulator-boot-on;
>> 337 regulator-min-microvolt = <900000>;
>> 338 regulator-max-microvolt = <900000>;
>> 339 regulator-state-mem {
>> 340 regulator-off-in-suspend;
>> 341 };
>> 342 };
>> 343
>> 344 vcc_3v0: LDO_REG8 {
>> 345 regulator-name = "vcc_3v0";
>> 346 regulator-always-on;
>> 347 regulator-boot-on;
>> 348 regulator-min-microvolt = <3000000>;
>> 349 regulator-max-microvolt = <3000000>;
>> 350 regulator-state-mem {
>> 351 regulator-on-in-suspend;
>> 352 regulator-suspend-microvolt = <3000000>;
>> 353 };
>> 354 };
>> 355
>> 356 vcc3v3_s3: vcc_lan: SWITCH_REG1 {
>> 357 regulator-name = "vcc3v3_s3";
>> 358 regulator-always-on;
>> 359 regulator-boot-on;
>> 360 regulator-state-mem {
>> 361 regulator-off-in-suspend;
>> 362 };
>> 363 };
>> 364
>> 365 vcc3v3_s0: SWITCH_REG2 {
>> 366 regulator-name = "vcc3v3_s0";
>> 367 regulator-always-on;
>> 368 regulator-boot-on;
>> 369 regulator-state-mem {
>> 370 regulator-off-in-suspend;
>> 371 };
>> 372 };
>> 373 };
>> 374 };
>> 375
>> 376 vdd_cpu_b: regulator@40 {
>> 377 compatible = "silergy,syr827";
>> 378 reg = <0x40>;
>> 379 fcs,suspend-voltage-selector = <1>;
>> 380 pinctrl-names = "default";
>> 381 pinctrl-0 = <&vsel1_gpio>;
>> 382 regulator-name = "vdd_cpu_b";
>> 383 regulator-min-microvolt = <712500>;
>> 384 regulator-max-microvolt = <1500000>;
>> 385 regulator-ramp-delay = <1000>;
>> 386 regulator-always-on;
>> 387 regulator-boot-on;
>> 388 vin-supply = <&vcc3v3_sys>;
>> 389
>> 390 regulator-state-mem {
>> 391 regulator-off-in-suspend;
>> 392 };
>> 393 };
>> 394
>> 395 vdd_gpu: regulator@41 {
>> 396 compatible = "silergy,syr828";
>> 397 reg = <0x41>;
>> 398 fcs,suspend-voltage-selector = <1>;
>> 399 pinctrl-names = "default";
>> 400 pinctrl-0 = <&vsel2_gpio>;
>> 401 regulator-name = "vdd_gpu";
>> 402 regulator-min-microvolt = <712500>;
>> 403 regulator-max-microvolt = <1500000>;
>> 404 regulator-ramp-delay = <1000>;
>> 405 regulator-always-on;
>> 406 regulator-boot-on;
>> 407 vin-supply = <&vcc3v3_sys>;
>> 408
>> 409 regulator-state-mem {
>> 410 regulator-off-in-suspend;
>> 411 };
>> 412 };
>> 413 };
>> 414
>> 415 &i2c1 {
>> 416 i2c-scl-rising-time-ns = <300>;
>> 417 i2c-scl-falling-time-ns = <15>;
>> 418 status = "okay";
>> 419 };
>> 420
>> 421 &i2c3 {
>> 422 i2c-scl-rising-time-ns = <450>;
>> 423 i2c-scl-falling-time-ns = <15>;
>> 424 status = "okay";
>> 425 };
>> 426
>> 427 &i2c4 {
>> 428 i2c-scl-rising-time-ns = <600>;
>> 429 i2c-scl-falling-time-ns = <20>;
>> 430 status = "okay";
>> 431
>> 432 fusb1: usb-typec@22 {
>> 433 compatible = "fcs,fusb302";
>> 434 reg = <0x22>;
>> 435 interrupt-parent = <&gpio1>;
>> 436 interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
>> 437 pinctrl-names = "default";
>> 438 pinctrl-0 = <&fusb1_int>;
>> 439 vbus-supply = <&vcc_vbus_typec1>;
>> 440 status = "okay";
>> 441 };
>> 442 };
>> 443
>> 444 &i2c7 {
>> 445 i2c-scl-rising-time-ns = <600>;
>> 446 i2c-scl-falling-time-ns = <20>;
>> 447 status = "okay";
>> 448
>> 449 fusb0: usb-typec@22 {
>> 450 compatible = "fcs,fusb302";
>> 451 reg = <0x22>;
>> 452 interrupt-parent = <&gpio1>;
>> 453 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
>> 454 pinctrl-names = "default";
>> 455 pinctrl-0 = <&fusb0_int>;
>> 456 vbus-supply = <&vcc_vbus_typec0>;
>> 457 status = "okay";
>> 458 };
>> 459 };
>> 460
>> 461 &i2s0 {
>> 462 rockchip,playback-channels = <8>;
>> 463 rockchip,capture-channels = <8>;
>> 464 status = "okay";
>> 465 };
>> 466
>> 467 &i2s1 {
>> 468 rockchip,playback-channels = <2>;
>> 469 rockchip,capture-channels = <2>;
>> 470 status = "okay";
>> 471 };
>> 472
>> 473 &i2s2 {
>> 474 status = "okay";
>> 475 };
>> 476
>> 477 &io_domains {
>> 478 audio-supply = <&vcca1v8_codec>;
>> 479 bt656-supply = <&vcc_3v0>;
>> 480 gpio1830-supply = <&vcc_3v0>;
>> 481 sdmmc-supply = <&vcc_sdio>;
>> 482 status = "okay";
>> 483 };
>> 484
>> 485 &pmu_io_domains {
>> 486 pmu1830-supply = <&vcc_3v0>;
>> 487 status = "okay";
>> 488 };
>> 489
>> 490 &pinctrl {
>> 491 lcd-panel {
>> 492 lcd_panel_reset: lcd-panel-reset {
>> 493 rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
>> 494 };
>> 495 };
>> 496
>> 497 pmic {
>> 498 vsel1_gpio: vsel1-gpio {
>> 499 rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
>> 500 };
>> 501
>> 502 vsel2_gpio: vsel2-gpio {
>> 503 rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
>> 504 };
>> 505 };
>> 506
>> 507 sdio-pwrseq {
>> 508 wifi_enable_h: wifi-enable-h {
>> 509 rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
>> 510 };
>> 511 };
>> 512
>> 513 pmic {
>> 514 pmic_int_l: pmic-int-l {
>> 515 rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
>> 516 };
>> 517 };
>> 518
>> 519 usb2 {
>> 520 vcc5v0_host_en: vcc5v0-host-en {
>> 521 rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
>> 522 };
>> 523
>> 524 hub_rst: hub-rst {
>> 525 rockchip,pins = <2 RK_PA4 RK_FUNC_GPIO &pcfg_output_high>;
>> 526 };
>> 527 };
>> 528
>> 529 usb-typec {
>> 530 vcc_vbus_typec1_en: vcc-vbus-typec1-en {
>> 531 rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
>> 532 };
>> 533 };
>> 534
>> 535 fusb30x {
>> 536 fusb0_int: fusb0-int {
>> 537 rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
>> 538 };
>> 539
>> 540 fusb1_int: fusb1-int {
>> 541 rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
>> 542 };
>> 543 };
>> 544 };
>> 545
>> 546 &pwm0 {
>> 547 status = "okay";
>> 548 };
>> 549
>> 550 &pwm2 {
>> 551 status = "okay";
>> 552 };
>> 553
>> 554 &saradc {
>> 555 vref-supply = <&vcca1v8_s3>;
>> 556 status = "okay";
>> 557 };
>> 558
>> 559 &sdmmc {
>> 560 bus-width = <4>;
>> 561 cap-mmc-highspeed;
>> 562 cap-sd-highspeed;
>> 563 cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
>> 564 disable-wp;
>> 565 max-frequency = <150000000>;
>> 566 pinctrl-names = "default";
>> 567 pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
>> 568 status = "okay";
>> 569 };
>> 570
>> 571 &sdhci {
>> 572 bus-width = <8>;
>> 573 mmc-hs400-1_8v;
>> 574 mmc-hs400-enhanced-strobe;
>> 575 non-removable;
>> 576 status = "okay";
>> 577 };
>> 578
>> 579 &tcphy0 {
>> 580 status = "okay";
>> 581 };
>> 582
>> 583 &tcphy1 {
>> 584 status = "okay";
>> 585 };
>> 586
>> 587 &tsadc {
>> 588 /* tshut mode 0:CRU 1:GPIO */
>> 589 rockchip,hw-tshut-mode = <1>;
>> 590 /* tshut polarity 0:LOW 1:HIGH */
>> 591 rockchip,hw-tshut-polarity = <1>;
>> 592 status = "okay";
>> 593 };
>> 594
>> 595 &u2phy0 {
>> 596 status = "okay";
>> 597
>> 598 u2phy0_otg: otg-port {
>> 599 phy-supply = <&vcc_vbus_typec0>;
>> 600 status = "okay";
>> 601 };
>> 602
>> 603 u2phy0_host: host-port {
>> 604 phy-supply = <&vcc5v0_host>;
>> 605 status = "okay";
>> 606 };
>> 607 };
>> 608
>> 609 &u2phy1 {
>> 610 status = "okay";
>> 611
>> 612 u2phy1_otg: otg-port {
>> 613 phy-supply = <&vcc_vbus_typec1>;
>> 614 status = "okay";
>> 615 };
>> 616
>> 617 u2phy1_host: host-port {
>> 618 phy-supply = <&vcc5v0_host>;
>> 619 status = "okay";
>> 620 };
>> 621 };
>> 622
>> 623 &uart0 {
>> 624 pinctrl-names = "default";
>> 625 pinctrl-0 = <&uart0_xfer &uart0_cts>;
>> 626 status = "okay";
>> 627 };
>> 628
>> 629 &uart2 {
>> 630 status = "okay";
>> 631 };
>> 632
>> 633 &usb_host0_ehci {
>> 634 status = "okay";
>> 635 };
>> 636
>> 637 &usb_host0_ohci {
>> 638 status = "okay";
>> 639 };
>> 640
>> 641 &usb_host1_ehci {
>> 642 status = "okay";
>> 643 };
>> 644
>> 645 &usb_host1_ohci {
>> 646 status = "okay";
>> 647 };
>> 648
>> 649 &usbdrd3_0 {
>> 650 status = "okay";
>> 651 };
>> 652
>> 653 &usbdrd_dwc3_0 {
>> 654 status = "okay";
>> 655 };
>> 656
>> 657 &usbdrd3_1 {
>> 658 status = "okay";
>> 659 };
>> 660
>> 661 &usbdrd_dwc3_1 {
>> 662 status = "okay";
>> 663 dr_mode = "host";
>> 664 };
>> 665
>> 666 &vopb {
>> 667 status = "okay";
>> 668 };
>> 669
>> 670 &vopb_mmu {
>> 671 status = "okay";
>> 672 };
>> 673
>> 674 &vopl {
>> 675 status = "okay";
>> 676 };
>> 677
>> 678 &vopl_mmu {
>> 679 status = "okay";
12 }; 680 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.