1 =================== 2 Setting up NFS/RDMA 3 =================== 4 5 :Author: 6 NetApp and Open Grid Computing (May 29, 2008) 7 8 .. warning:: 9 This document is probably obsolete. 10 11 Overview 12 ======== 13 14 This document describes how to install and setup the Linux NFS/RDMA client 15 and server software. 16 17 The NFS/RDMA client was first included in Linux 2.6.24. The NFS/RDMA server 18 was first included in the following release, Linux 2.6.25. 19 20 In our testing, we have obtained excellent performance results (full 10Gbit 21 wire bandwidth at minimal client CPU) under many workloads. The code passes 22 the full Connectathon test suite and operates over both Infiniband and iWARP 23 RDMA adapters. 24 25 Getting Help 26 ============ 27 28 If you get stuck, you can ask questions on the 29 nfs-rdma-devel@lists.sourceforge.net mailing list. 30 31 Installation 32 ============ 33 34 These instructions are a step by step guide to building a machine for 35 use with NFS/RDMA. 36 37 - Install an RDMA device 38 39 Any device supported by the drivers in drivers/infiniband/hw is acceptable. 40 41 Testing has been performed using several Mellanox-based IB cards, the 42 Ammasso AMS1100 iWARP adapter, and the Chelsio cxgb3 iWARP adapter. 43 44 - Install a Linux distribution and tools 45 46 The first kernel release to contain both the NFS/RDMA client and server was 47 Linux 2.6.25 Therefore, a distribution compatible with this and subsequent 48 Linux kernel release should be installed. 49 50 The procedures described in this document have been tested with 51 distributions from Red Hat's Fedora Project (http://fedora.redhat.com/). 52 53 - Install nfs-utils-1.1.2 or greater on the client 54 55 An NFS/RDMA mount point can be obtained by using the mount.nfs command in 56 nfs-utils-1.1.2 or greater (nfs-utils-1.1.1 was the first nfs-utils 57 version with support for NFS/RDMA mounts, but for various reasons we 58 recommend using nfs-utils-1.1.2 or greater). To see which version of 59 mount.nfs you are using, type: 60 61 .. code-block:: sh 62 63 $ /sbin/mount.nfs -V 64 65 If the version is less than 1.1.2 or the command does not exist, 66 you should install the latest version of nfs-utils. 67 68 Download the latest package from: https://www.kernel.org/pub/linux/utils/nfs 69 70 Uncompress the package and follow the installation instructions. 71 72 If you will not need the idmapper and gssd executables (you do not need 73 these to create an NFS/RDMA enabled mount command), the installation 74 process can be simplified by disabling these features when running 75 configure: 76 77 .. code-block:: sh 78 79 $ ./configure --disable-gss --disable-nfsv4 80 81 To build nfs-utils you will need the tcp_wrappers package installed. For 82 more information on this see the package's README and INSTALL files. 83 84 After building the nfs-utils package, there will be a mount.nfs binary in 85 the utils/mount directory. This binary can be used to initiate NFS v2, v3, 86 or v4 mounts. To initiate a v4 mount, the binary must be called 87 mount.nfs4. The standard technique is to create a symlink called 88 mount.nfs4 to mount.nfs. 89 90 This mount.nfs binary should be installed at /sbin/mount.nfs as follows: 91 92 .. code-block:: sh 93 94 $ sudo cp utils/mount/mount.nfs /sbin/mount.nfs 95 96 In this location, mount.nfs will be invoked automatically for NFS mounts 97 by the system mount command. 98 99 .. note:: 100 mount.nfs and therefore nfs-utils-1.1.2 or greater is only needed 101 on the NFS client machine. You do not need this specific version of 102 nfs-utils on the server. Furthermore, only the mount.nfs command from 103 nfs-utils-1.1.2 is needed on the client. 104 105 - Install a Linux kernel with NFS/RDMA 106 107 The NFS/RDMA client and server are both included in the mainline Linux 108 kernel version 2.6.25 and later. This and other versions of the Linux 109 kernel can be found at: https://www.kernel.org/pub/linux/kernel/ 110 111 Download the sources and place them in an appropriate location. 112 113 - Configure the RDMA stack 114 115 Make sure your kernel configuration has RDMA support enabled. Under 116 Device Drivers -> InfiniBand support, update the kernel configuration 117 to enable InfiniBand support [NOTE: the option name is misleading. Enabling 118 InfiniBand support is required for all RDMA devices (IB, iWARP, etc.)]. 119 120 Enable the appropriate IB HCA support (mlx4, mthca, ehca, ipath, etc.) or 121 iWARP adapter support (amso, cxgb3, etc.). 122 123 If you are using InfiniBand, be sure to enable IP-over-InfiniBand support. 124 125 - Configure the NFS client and server 126 127 Your kernel configuration must also have NFS file system support and/or 128 NFS server support enabled. These and other NFS related configuration 129 options can be found under File Systems -> Network File Systems. 130 131 - Build, install, reboot 132 133 The NFS/RDMA code will be enabled automatically if NFS and RDMA 134 are turned on. The NFS/RDMA client and server are configured via the hidden 135 SUNRPC_XPRT_RDMA config option that depends on SUNRPC and INFINIBAND. The 136 value of SUNRPC_XPRT_RDMA will be: 137 138 #. N if either SUNRPC or INFINIBAND are N, in this case the NFS/RDMA client 139 and server will not be built 140 141 #. M if both SUNRPC and INFINIBAND are on (M or Y) and at least one is M, 142 in this case the NFS/RDMA client and server will be built as modules 143 144 #. Y if both SUNRPC and INFINIBAND are Y, in this case the NFS/RDMA client 145 and server will be built into the kernel 146 147 Therefore, if you have followed the steps above and turned no NFS and RDMA, 148 the NFS/RDMA client and server will be built. 149 150 Build a new kernel, install it, boot it. 151 152 Check RDMA and NFS Setup 153 ======================== 154 155 Before configuring the NFS/RDMA software, it is a good idea to test 156 your new kernel to ensure that the kernel is working correctly. 157 In particular, it is a good idea to verify that the RDMA stack 158 is functioning as expected and standard NFS over TCP/IP and/or UDP/IP 159 is working properly. 160 161 - Check RDMA Setup 162 163 If you built the RDMA components as modules, load them at 164 this time. For example, if you are using a Mellanox Tavor/Sinai/Arbel 165 card: 166 167 .. code-block:: sh 168 169 $ modprobe ib_mthca 170 $ modprobe ib_ipoib 171 172 If you are using InfiniBand, make sure there is a Subnet Manager (SM) 173 running on the network. If your IB switch has an embedded SM, you can 174 use it. Otherwise, you will need to run an SM, such as OpenSM, on one 175 of your end nodes. 176 177 If an SM is running on your network, you should see the following: 178 179 .. code-block:: sh 180 181 $ cat /sys/class/infiniband/driverX/ports/1/state 182 4: ACTIVE 183 184 where driverX is mthca0, ipath5, ehca3, etc. 185 186 To further test the InfiniBand software stack, use IPoIB (this 187 assumes you have two IB hosts named host1 and host2): 188 189 .. code-block:: sh 190 191 host1$ ip link set dev ib0 up 192 host1$ ip address add dev ib0 a.b.c.x 193 host2$ ip link set dev ib0 up 194 host2$ ip address add dev ib0 a.b.c.y 195 host1$ ping a.b.c.y 196 host2$ ping a.b.c.x 197 198 For other device types, follow the appropriate procedures. 199 200 - Check NFS Setup 201 202 For the NFS components enabled above (client and/or server), 203 test their functionality over standard Ethernet using TCP/IP or UDP/IP. 204 205 NFS/RDMA Setup 206 ============== 207 208 We recommend that you use two machines, one to act as the client and 209 one to act as the server. 210 211 One time configuration: 212 ----------------------- 213 214 - On the server system, configure the /etc/exports file and start the NFS/RDMA server. 215 216 Exports entries with the following formats have been tested:: 217 218 /vol0 192.168.0.47(fsid=0,rw,async,insecure,no_root_squash) 219 /vol0 192.168.0.0/255.255.255.0(fsid=0,rw,async,insecure,no_root_squash) 220 221 The IP address(es) is(are) the client's IPoIB address for an InfiniBand 222 HCA or the client's iWARP address(es) for an RNIC. 223 224 .. note:: 225 The "insecure" option must be used because the NFS/RDMA client does 226 not use a reserved port. 227 228 Each time a machine boots: 229 -------------------------- 230 231 - Load and configure the RDMA drivers 232 233 For InfiniBand using a Mellanox adapter: 234 235 .. code-block:: sh 236 237 $ modprobe ib_mthca 238 $ modprobe ib_ipoib 239 $ ip li set dev ib0 up 240 $ ip addr add dev ib0 a.b.c.d 241 242 .. note:: 243 Please use unique addresses for the client and server! 244 245 - Start the NFS server 246 247 If the NFS/RDMA server was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in 248 kernel config), load the RDMA transport module: 249 250 .. code-block:: sh 251 252 $ modprobe svcrdma 253 254 Regardless of how the server was built (module or built-in), start the 255 server: 256 257 .. code-block:: sh 258 259 $ /etc/init.d/nfs start 260 261 or 262 263 .. code-block:: sh 264 265 $ service nfs start 266 267 Instruct the server to listen on the RDMA transport: 268 269 .. code-block:: sh 270 271 $ echo rdma 20049 > /proc/fs/nfsd/portlist 272 273 - On the client system 274 275 If the NFS/RDMA client was built as a module (CONFIG_SUNRPC_XPRT_RDMA=m in 276 kernel config), load the RDMA client module: 277 278 .. code-block:: sh 279 280 $ modprobe xprtrdma.ko 281 282 Regardless of how the client was built (module or built-in), use this 283 command to mount the NFS/RDMA server: 284 285 .. code-block:: sh 286 287 $ mount -o rdma,port=20049 <IPoIB-server-name-or-address>:/<export> /mnt 288 289 To verify that the mount is using RDMA, run "cat /proc/mounts" and check 290 the "proto" field for the given mount. 291 292 Congratulations! You're using NFS/RDMA!
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.