1 ===================== 2 I2C/SMBUS Fault Codes 3 ===================== 4 5 This is a summary of the most important conventions for use of fault 6 codes in the I2C/SMBus stack. 7 8 9 A "Fault" is not always an "Error" 10 ---------------------------------- 11 Not all fault reports imply errors; "page faults" should be a familiar 12 example. Software often retries idempotent operations after transient 13 faults. There may be fancier recovery schemes that are appropriate in 14 some cases, such as re-initializing (and maybe resetting). After such 15 recovery, triggered by a fault report, there is no error. 16 17 In a similar way, sometimes a "fault" code just reports one defined 18 result for an operation ... it doesn't indicate that anything is wrong 19 at all, just that the outcome wasn't on the "golden path". 20 21 In short, your I2C driver code may need to know these codes in order 22 to respond correctly. Other code may need to rely on YOUR code reporting 23 the right fault code, so that it can (in turn) behave correctly. 24 25 26 I2C and SMBus fault codes 27 ------------------------- 28 These are returned as negative numbers from most calls, with zero or 29 some positive number indicating a non-fault return. The specific 30 numbers associated with these symbols differ between architectures, 31 though most Linux systems use <asm-generic/errno*.h> numbering. 32 33 Note that the descriptions here are not exhaustive. There are other 34 codes that may be returned, and other cases where these codes should 35 be returned. However, drivers should not return other codes for these 36 cases (unless the hardware doesn't provide unique fault reports). 37 38 Also, codes returned by adapter probe methods follow rules which are 39 specific to their host bus (such as PCI, or the platform bus). 40 41 42 EAFNOSUPPORT 43 Returned by I2C adapters not supporting 10 bit addresses when 44 they are requested to use such an address. 45 46 EAGAIN 47 Returned by I2C adapters when they lose arbitration in master 48 transmit mode: some other master was transmitting different 49 data at the same time. 50 51 Also returned when trying to invoke an I2C operation in an 52 atomic context, when some task is already using that I2C bus 53 to execute some other operation. 54 55 EBADMSG 56 Returned by SMBus logic when an invalid Packet Error Code byte 57 is received. This code is a CRC covering all bytes in the 58 transaction, and is sent before the terminating STOP. This 59 fault is only reported on read transactions; the SMBus slave 60 may have a way to report PEC mismatches on writes from the 61 host. Note that even if PECs are in use, you should not rely 62 on these as the only way to detect incorrect data transfers. 63 64 EBUSY 65 Returned by SMBus adapters when the bus was busy for longer 66 than allowed. This usually indicates some device (maybe the 67 SMBus adapter) needs some fault recovery (such as resetting), 68 or that the reset was attempted but failed. 69 70 EINVAL 71 This rather vague error means an invalid parameter has been 72 detected before any I/O operation was started. Use a more 73 specific fault code when you can. 74 75 EIO 76 This rather vague error means something went wrong when 77 performing an I/O operation. Use a more specific fault 78 code when you can. 79 80 ENODEV 81 Returned by driver probe() methods. This is a bit more 82 specific than ENXIO, implying the problem isn't with the 83 address, but with the device found there. Driver probes 84 may verify the device returns *correct* responses, and 85 return this as appropriate. (The driver core will warn 86 about probe faults other than ENXIO and ENODEV.) 87 88 ENOMEM 89 Returned by any component that can't allocate memory when 90 it needs to do so. 91 92 ENXIO 93 Returned by I2C adapters to indicate that the address phase 94 of a transfer didn't get an ACK. While it might just mean 95 an I2C device was temporarily not responding, usually it 96 means there's nothing listening at that address. 97 98 Returned by driver probe() methods to indicate that they 99 found no device to bind to. (ENODEV may also be used.) 100 101 EOPNOTSUPP 102 Returned by an adapter when asked to perform an operation 103 that it doesn't, or can't, support. 104 105 For example, this would be returned when an adapter that 106 doesn't support SMBus block transfers is asked to execute 107 one. In that case, the driver making that request should 108 have verified that functionality was supported before it 109 made that block transfer request. 110 111 Similarly, if an I2C adapter can't execute all legal I2C 112 messages, it should return this when asked to perform a 113 transaction it can't. (These limitations can't be seen in 114 the adapter's functionality mask, since the assumption is 115 that if an adapter supports I2C it supports all of I2C.) 116 117 EPROTO 118 Returned when slave does not conform to the relevant I2C 119 or SMBus (or chip-specific) protocol specifications. One 120 case is when the length of an SMBus block data response 121 (from the SMBus slave) is outside the range 1-32 bytes. 122 123 ESHUTDOWN 124 Returned when a transfer was requested using an adapter 125 which is already suspended. 126 127 ETIMEDOUT 128 This is returned by drivers when an operation took too much 129 time, and was aborted before it completed. 130 131 SMBus adapters may return it when an operation took more 132 time than allowed by the SMBus specification; for example, 133 when a slave stretches clocks too far. I2C has no such 134 timeouts, but it's normal for I2C adapters to impose some 135 arbitrary limits (much longer than SMBus!) too.
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.