1 =================================== 2 SocketCAN - Controller Area Network 3 =================================== 4 5 Overview / What is SocketCAN 6 ============================ 7 8 The socketcan package is an implementation of CAN protocols 9 (Controller Area Network) for Linux. CAN is a networking technology 10 which has widespread use in automation, embedded devices, and 11 automotive fields. While there have been other CAN implementations 12 for Linux based on character devices, SocketCAN uses the Berkeley 13 socket API, the Linux network stack and implements the CAN device 14 drivers as network interfaces. The CAN socket API has been designed 15 as similar as possible to the TCP/IP protocols to allow programmers, 16 familiar with network programming, to easily learn how to use CAN 17 sockets. 18 19 20 .. _socketcan-motivation: 21 22 Motivation / Why Using the Socket API 23 ===================================== 24 25 There have been CAN implementations for Linux before SocketCAN so the 26 question arises, why we have started another project. Most existing 27 implementations come as a device driver for some CAN hardware, they 28 are based on character devices and provide comparatively little 29 functionality. Usually, there is only a hardware-specific device 30 driver which provides a character device interface to send and 31 receive raw CAN frames, directly to/from the controller hardware. 32 Queueing of frames and higher-level transport protocols like ISO-TP 33 have to be implemented in user space applications. Also, most 34 character-device implementations support only one single process to 35 open the device at a time, similar to a serial interface. Exchanging 36 the CAN controller requires employment of another device driver and 37 often the need for adaption of large parts of the application to the 38 new driver's API. 39 40 SocketCAN was designed to overcome all of these limitations. A new 41 protocol family has been implemented which provides a socket interface 42 to user space applications and which builds upon the Linux network 43 layer, enabling use all of the provided queueing functionality. A device 44 driver for CAN controller hardware registers itself with the Linux 45 network layer as a network device, so that CAN frames from the 46 controller can be passed up to the network layer and on to the CAN 47 protocol family module and also vice-versa. Also, the protocol family 48 module provides an API for transport protocol modules to register, so 49 that any number of transport protocols can be loaded or unloaded 50 dynamically. In fact, the can core module alone does not provide any 51 protocol and cannot be used without loading at least one additional 52 protocol module. Multiple sockets can be opened at the same time, 53 on different or the same protocol module and they can listen/send 54 frames on different or the same CAN IDs. Several sockets listening on 55 the same interface for frames with the same CAN ID are all passed the 56 same received matching CAN frames. An application wishing to 57 communicate using a specific transport protocol, e.g. ISO-TP, just 58 selects that protocol when opening the socket, and then can read and 59 write application data byte streams, without having to deal with 60 CAN-IDs, frames, etc. 61 62 Similar functionality visible from user-space could be provided by a 63 character device, too, but this would lead to a technically inelegant 64 solution for a couple of reasons: 65 66 * **Intricate usage:** Instead of passing a protocol argument to 67 socket(2) and using bind(2) to select a CAN interface and CAN ID, an 68 application would have to do all these operations using ioctl(2)s. 69 70 * **Code duplication:** A character device cannot make use of the Linux 71 network queueing code, so all that code would have to be duplicated 72 for CAN networking. 73 74 * **Abstraction:** In most existing character-device implementations, the 75 hardware-specific device driver for a CAN controller directly 76 provides the character device for the application to work with. 77 This is at least very unusual in Unix systems for both, char and 78 block devices. For example you don't have a character device for a 79 certain UART of a serial interface, a certain sound chip in your 80 computer, a SCSI or IDE controller providing access to your hard 81 disk or tape streamer device. Instead, you have abstraction layers 82 which provide a unified character or block device interface to the 83 application on the one hand, and a interface for hardware-specific 84 device drivers on the other hand. These abstractions are provided 85 by subsystems like the tty layer, the audio subsystem or the SCSI 86 and IDE subsystems for the devices mentioned above. 87 88 The easiest way to implement a CAN device driver is as a character 89 device without such a (complete) abstraction layer, as is done by most 90 existing drivers. The right way, however, would be to add such a 91 layer with all the functionality like registering for certain CAN 92 IDs, supporting several open file descriptors and (de)multiplexing 93 CAN frames between them, (sophisticated) queueing of CAN frames, and 94 providing an API for device drivers to register with. However, then 95 it would be no more difficult, or may be even easier, to use the 96 networking framework provided by the Linux kernel, and this is what 97 SocketCAN does. 98 99 The use of the networking framework of the Linux kernel is just the 100 natural and most appropriate way to implement CAN for Linux. 101 102 103 .. _socketcan-concept: 104 105 SocketCAN Concept 106 ================= 107 108 As described in :ref:`socketcan-motivation` the main goal of SocketCAN is to 109 provide a socket interface to user space applications which builds 110 upon the Linux network layer. In contrast to the commonly known 111 TCP/IP and ethernet networking, the CAN bus is a broadcast-only(!) 112 medium that has no MAC-layer addressing like ethernet. The CAN-identifier 113 (can_id) is used for arbitration on the CAN-bus. Therefore the CAN-IDs 114 have to be chosen uniquely on the bus. When designing a CAN-ECU 115 network the CAN-IDs are mapped to be sent by a specific ECU. 116 For this reason a CAN-ID can be treated best as a kind of source address. 117 118 119 .. _socketcan-receive-lists: 120 121 Receive Lists 122 ------------- 123 124 The network transparent access of multiple applications leads to the 125 problem that different applications may be interested in the same 126 CAN-IDs from the same CAN network interface. The SocketCAN core 127 module - which implements the protocol family CAN - provides several 128 high efficient receive lists for this reason. If e.g. a user space 129 application opens a CAN RAW socket, the raw protocol module itself 130 requests the (range of) CAN-IDs from the SocketCAN core that are 131 requested by the user. The subscription and unsubscription of 132 CAN-IDs can be done for specific CAN interfaces or for all(!) known 133 CAN interfaces with the can_rx_(un)register() functions provided to 134 CAN protocol modules by the SocketCAN core (see :ref:`socketcan-core-module`). 135 To optimize the CPU usage at runtime the receive lists are split up 136 into several specific lists per device that match the requested 137 filter complexity for a given use-case. 138 139 140 .. _socketcan-local-loopback1: 141 142 Local Loopback of Sent Frames 143 ----------------------------- 144 145 As known from other networking concepts the data exchanging 146 applications may run on the same or different nodes without any 147 change (except for the according addressing information): 148 149 .. code:: 150 151 ___ ___ ___ _______ ___ 152 | _ | | _ | | _ | | _ _ | | _ | 153 ||A|| ||B|| ||C|| ||A| |B|| ||C|| 154 |___| |___| |___| |_______| |___| 155 | | | | | 156 -----------------(1)- CAN bus -(2)--------------- 157 158 To ensure that application A receives the same information in the 159 example (2) as it would receive in example (1) there is need for 160 some kind of local loopback of the sent CAN frames on the appropriate 161 node. 162 163 The Linux network devices (by default) just can handle the 164 transmission and reception of media dependent frames. Due to the 165 arbitration on the CAN bus the transmission of a low prio CAN-ID 166 may be delayed by the reception of a high prio CAN frame. To 167 reflect the correct [#f1]_ traffic on the node the loopback of the sent 168 data has to be performed right after a successful transmission. If 169 the CAN network interface is not capable of performing the loopback for 170 some reason the SocketCAN core can do this task as a fallback solution. 171 See :ref:`socketcan-local-loopback2` for details (recommended). 172 173 The loopback functionality is enabled by default to reflect standard 174 networking behaviour for CAN applications. Due to some requests from 175 the RT-SocketCAN group the loopback optionally may be disabled for each 176 separate socket. See sockopts from the CAN RAW sockets in :ref:`socketcan-raw-sockets`. 177 178 .. [#f1] you really like to have this when you're running analyser 179 tools like 'candump' or 'cansniffer' on the (same) node. 180 181 182 .. _socketcan-network-problem-notifications: 183 184 Network Problem Notifications 185 ----------------------------- 186 187 The use of the CAN bus may lead to several problems on the physical 188 and media access control layer. Detecting and logging of these lower 189 layer problems is a vital requirement for CAN users to identify 190 hardware issues on the physical transceiver layer as well as 191 arbitration problems and error frames caused by the different 192 ECUs. The occurrence of detected errors are important for diagnosis 193 and have to be logged together with the exact timestamp. For this 194 reason the CAN interface driver can generate so called Error Message 195 Frames that can optionally be passed to the user application in the 196 same way as other CAN frames. Whenever an error on the physical layer 197 or the MAC layer is detected (e.g. by the CAN controller) the driver 198 creates an appropriate error message frame. Error messages frames can 199 be requested by the user application using the common CAN filter 200 mechanisms. Inside this filter definition the (interested) type of 201 errors may be selected. The reception of error messages is disabled 202 by default. The format of the CAN error message frame is briefly 203 described in the Linux header file "include/uapi/linux/can/error.h". 204 205 206 How to use SocketCAN 207 ==================== 208 209 Like TCP/IP, you first need to open a socket for communicating over a 210 CAN network. Since SocketCAN implements a new protocol family, you 211 need to pass PF_CAN as the first argument to the socket(2) system 212 call. Currently, there are two CAN protocols to choose from, the raw 213 socket protocol and the broadcast manager (BCM). So to open a socket, 214 you would write:: 215 216 s = socket(PF_CAN, SOCK_RAW, CAN_RAW); 217 218 and:: 219 220 s = socket(PF_CAN, SOCK_DGRAM, CAN_BCM); 221 222 respectively. After the successful creation of the socket, you would 223 normally use the bind(2) system call to bind the socket to a CAN 224 interface (which is different from TCP/IP due to different addressing 225 - see :ref:`socketcan-concept`). After binding (CAN_RAW) or connecting (CAN_BCM) 226 the socket, you can read(2) and write(2) from/to the socket or use 227 send(2), sendto(2), sendmsg(2) and the recv* counterpart operations 228 on the socket as usual. There are also CAN specific socket options 229 described below. 230 231 The Classical CAN frame structure (aka CAN 2.0B), the CAN FD frame structure 232 and the sockaddr structure are defined in include/linux/can.h: 233 234 .. code-block:: C 235 236 struct can_frame { 237 canid_t can_id; /* 32 bit CAN_ID + EFF/RTR/ERR flags */ 238 union { 239 /* CAN frame payload length in byte (0 .. CAN_MAX_DLEN) 240 * was previously named can_dlc so we need to carry that 241 * name for legacy support 242 */ 243 __u8 len; 244 __u8 can_dlc; /* deprecated */ 245 }; 246 __u8 __pad; /* padding */ 247 __u8 __res0; /* reserved / padding */ 248 __u8 len8_dlc; /* optional DLC for 8 byte payload length (9 .. 15) */ 249 __u8 data[8] __attribute__((aligned(8))); 250 }; 251 252 Remark: The len element contains the payload length in bytes and should be 253 used instead of can_dlc. The deprecated can_dlc was misleadingly named as 254 it always contained the plain payload length in bytes and not the so called 255 'data length code' (DLC). 256 257 To pass the raw DLC from/to a Classical CAN network device the len8_dlc 258 element can contain values 9 .. 15 when the len element is 8 (the real 259 payload length for all DLC values greater or equal to 8). 260 261 The alignment of the (linear) payload data[] to a 64bit boundary 262 allows the user to define their own structs and unions to easily access 263 the CAN payload. There is no given byteorder on the CAN bus by 264 default. A read(2) system call on a CAN_RAW socket transfers a 265 struct can_frame to the user space. 266 267 The sockaddr_can structure has an interface index like the 268 PF_PACKET socket, that also binds to a specific interface: 269 270 .. code-block:: C 271 272 struct sockaddr_can { 273 sa_family_t can_family; 274 int can_ifindex; 275 union { 276 /* transport protocol class address info (e.g. ISOTP) */ 277 struct { canid_t rx_id, tx_id; } tp; 278 279 /* J1939 address information */ 280 struct { 281 /* 8 byte name when using dynamic addressing */ 282 __u64 name; 283 284 /* pgn: 285 * 8 bit: PS in PDU2 case, else 0 286 * 8 bit: PF 287 * 1 bit: DP 288 * 1 bit: reserved 289 */ 290 __u32 pgn; 291 292 /* 1 byte address */ 293 __u8 addr; 294 } j1939; 295 296 /* reserved for future CAN protocols address information */ 297 } can_addr; 298 }; 299 300 To determine the interface index an appropriate ioctl() has to 301 be used (example for CAN_RAW sockets without error checking): 302 303 .. code-block:: C 304 305 int s; 306 struct sockaddr_can addr; 307 struct ifreq ifr; 308 309 s = socket(PF_CAN, SOCK_RAW, CAN_RAW); 310 311 strcpy(ifr.ifr_name, "can0" ); 312 ioctl(s, SIOCGIFINDEX, &ifr); 313 314 addr.can_family = AF_CAN; 315 addr.can_ifindex = ifr.ifr_ifindex; 316 317 bind(s, (struct sockaddr *)&addr, sizeof(addr)); 318 319 (..) 320 321 To bind a socket to all(!) CAN interfaces the interface index must 322 be 0 (zero). In this case the socket receives CAN frames from every 323 enabled CAN interface. To determine the originating CAN interface 324 the system call recvfrom(2) may be used instead of read(2). To send 325 on a socket that is bound to 'any' interface sendto(2) is needed to 326 specify the outgoing interface. 327 328 Reading CAN frames from a bound CAN_RAW socket (see above) consists 329 of reading a struct can_frame: 330 331 .. code-block:: C 332 333 struct can_frame frame; 334 335 nbytes = read(s, &frame, sizeof(struct can_frame)); 336 337 if (nbytes < 0) { 338 perror("can raw socket read"); 339 return 1; 340 } 341 342 /* paranoid check ... */ 343 if (nbytes < sizeof(struct can_frame)) { 344 fprintf(stderr, "read: incomplete CAN frame\n"); 345 return 1; 346 } 347 348 /* do something with the received CAN frame */ 349 350 Writing CAN frames can be done similarly, with the write(2) system call:: 351 352 nbytes = write(s, &frame, sizeof(struct can_frame)); 353 354 When the CAN interface is bound to 'any' existing CAN interface 355 (addr.can_ifindex = 0) it is recommended to use recvfrom(2) if the 356 information about the originating CAN interface is needed: 357 358 .. code-block:: C 359 360 struct sockaddr_can addr; 361 struct ifreq ifr; 362 socklen_t len = sizeof(addr); 363 struct can_frame frame; 364 365 nbytes = recvfrom(s, &frame, sizeof(struct can_frame), 366 0, (struct sockaddr*)&addr, &len); 367 368 /* get interface name of the received CAN frame */ 369 ifr.ifr_ifindex = addr.can_ifindex; 370 ioctl(s, SIOCGIFNAME, &ifr); 371 printf("Received a CAN frame from interface %s", ifr.ifr_name); 372 373 To write CAN frames on sockets bound to 'any' CAN interface the 374 outgoing interface has to be defined certainly: 375 376 .. code-block:: C 377 378 strcpy(ifr.ifr_name, "can0"); 379 ioctl(s, SIOCGIFINDEX, &ifr); 380 addr.can_ifindex = ifr.ifr_ifindex; 381 addr.can_family = AF_CAN; 382 383 nbytes = sendto(s, &frame, sizeof(struct can_frame), 384 0, (struct sockaddr*)&addr, sizeof(addr)); 385 386 An accurate timestamp can be obtained with an ioctl(2) call after reading 387 a message from the socket: 388 389 .. code-block:: C 390 391 struct timeval tv; 392 ioctl(s, SIOCGSTAMP, &tv); 393 394 The timestamp has a resolution of one microsecond and is set automatically 395 at the reception of a CAN frame. 396 397 Remark about CAN FD (flexible data rate) support: 398 399 Generally the handling of CAN FD is very similar to the formerly described 400 examples. The new CAN FD capable CAN controllers support two different 401 bitrates for the arbitration phase and the payload phase of the CAN FD frame 402 and up to 64 bytes of payload. This extended payload length breaks all the 403 kernel interfaces (ABI) which heavily rely on the CAN frame with fixed eight 404 bytes of payload (struct can_frame) like the CAN_RAW socket. Therefore e.g. 405 the CAN_RAW socket supports a new socket option CAN_RAW_FD_FRAMES that 406 switches the socket into a mode that allows the handling of CAN FD frames 407 and Classical CAN frames simultaneously (see :ref:`socketcan-rawfd`). 408 409 The struct canfd_frame is defined in include/linux/can.h: 410 411 .. code-block:: C 412 413 struct canfd_frame { 414 canid_t can_id; /* 32 bit CAN_ID + EFF/RTR/ERR flags */ 415 __u8 len; /* frame payload length in byte (0 .. 64) */ 416 __u8 flags; /* additional flags for CAN FD */ 417 __u8 __res0; /* reserved / padding */ 418 __u8 __res1; /* reserved / padding */ 419 __u8 data[64] __attribute__((aligned(8))); 420 }; 421 422 The struct canfd_frame and the existing struct can_frame have the can_id, 423 the payload length and the payload data at the same offset inside their 424 structures. This allows to handle the different structures very similar. 425 When the content of a struct can_frame is copied into a struct canfd_frame 426 all structure elements can be used as-is - only the data[] becomes extended. 427 428 When introducing the struct canfd_frame it turned out that the data length 429 code (DLC) of the struct can_frame was used as a length information as the 430 length and the DLC has a 1:1 mapping in the range of 0 .. 8. To preserve 431 the easy handling of the length information the canfd_frame.len element 432 contains a plain length value from 0 .. 64. So both canfd_frame.len and 433 can_frame.len are equal and contain a length information and no DLC. 434 For details about the distinction of CAN and CAN FD capable devices and 435 the mapping to the bus-relevant data length code (DLC), see :ref:`socketcan-can-fd-driver`. 436 437 The length of the two CAN(FD) frame structures define the maximum transfer 438 unit (MTU) of the CAN(FD) network interface and skbuff data length. Two 439 definitions are specified for CAN specific MTUs in include/linux/can.h: 440 441 .. code-block:: C 442 443 #define CAN_MTU (sizeof(struct can_frame)) == 16 => Classical CAN frame 444 #define CANFD_MTU (sizeof(struct canfd_frame)) == 72 => CAN FD frame 445 446 447 Returned Message Flags 448 ---------------------- 449 450 When using the system call recvmsg(2) on a RAW or a BCM socket, the 451 msg->msg_flags field may contain the following flags: 452 453 MSG_DONTROUTE: 454 set when the received frame was created on the local host. 455 456 MSG_CONFIRM: 457 set when the frame was sent via the socket it is received on. 458 This flag can be interpreted as a 'transmission confirmation' when the 459 CAN driver supports the echo of frames on driver level, see 460 :ref:`socketcan-local-loopback1` and :ref:`socketcan-local-loopback2`. 461 (Note: In order to receive such messages on a RAW socket, 462 CAN_RAW_RECV_OWN_MSGS must be set.) 463 464 465 .. _socketcan-raw-sockets: 466 467 RAW Protocol Sockets with can_filters (SOCK_RAW) 468 ------------------------------------------------ 469 470 Using CAN_RAW sockets is extensively comparable to the commonly 471 known access to CAN character devices. To meet the new possibilities 472 provided by the multi user SocketCAN approach, some reasonable 473 defaults are set at RAW socket binding time: 474 475 - The filters are set to exactly one filter receiving everything 476 - The socket only receives valid data frames (=> no error message frames) 477 - The loopback of sent CAN frames is enabled (see :ref:`socketcan-local-loopback2`) 478 - The socket does not receive its own sent frames (in loopback mode) 479 480 These default settings may be changed before or after binding the socket. 481 To use the referenced definitions of the socket options for CAN_RAW 482 sockets, include <linux/can/raw.h>. 483 484 485 .. _socketcan-rawfilter: 486 487 RAW socket option CAN_RAW_FILTER 488 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 489 490 The reception of CAN frames using CAN_RAW sockets can be controlled 491 by defining 0 .. n filters with the CAN_RAW_FILTER socket option. 492 493 The CAN filter structure is defined in include/linux/can.h: 494 495 .. code-block:: C 496 497 struct can_filter { 498 canid_t can_id; 499 canid_t can_mask; 500 }; 501 502 A filter matches, when: 503 504 .. code-block:: C 505 506 <received_can_id> & mask == can_id & mask 507 508 which is analogous to known CAN controllers hardware filter semantics. 509 The filter can be inverted in this semantic, when the CAN_INV_FILTER 510 bit is set in can_id element of the can_filter structure. In 511 contrast to CAN controller hardware filters the user may set 0 .. n 512 receive filters for each open socket separately: 513 514 .. code-block:: C 515 516 struct can_filter rfilter[2]; 517 518 rfilter[0].can_id = 0x123; 519 rfilter[0].can_mask = CAN_SFF_MASK; 520 rfilter[1].can_id = 0x200; 521 rfilter[1].can_mask = 0x700; 522 523 setsockopt(s, SOL_CAN_RAW, CAN_RAW_FILTER, &rfilter, sizeof(rfilter)); 524 525 To disable the reception of CAN frames on the selected CAN_RAW socket: 526 527 .. code-block:: C 528 529 setsockopt(s, SOL_CAN_RAW, CAN_RAW_FILTER, NULL, 0); 530 531 To set the filters to zero filters is quite obsolete as to not read 532 data causes the raw socket to discard the received CAN frames. But 533 having this 'send only' use-case we may remove the receive list in the 534 Kernel to save a little (really a very little!) CPU usage. 535 536 CAN Filter Usage Optimisation 537 ............................. 538 539 The CAN filters are processed in per-device filter lists at CAN frame 540 reception time. To reduce the number of checks that need to be performed 541 while walking through the filter lists the CAN core provides an optimized 542 filter handling when the filter subscription focusses on a single CAN ID. 543 544 For the possible 2048 SFF CAN identifiers the identifier is used as an index 545 to access the corresponding subscription list without any further checks. 546 For the 2^29 possible EFF CAN identifiers a 10 bit XOR folding is used as 547 hash function to retrieve the EFF table index. 548 549 To benefit from the optimized filters for single CAN identifiers the 550 CAN_SFF_MASK or CAN_EFF_MASK have to be set into can_filter.mask together 551 with set CAN_EFF_FLAG and CAN_RTR_FLAG bits. A set CAN_EFF_FLAG bit in the 552 can_filter.mask makes clear that it matters whether a SFF or EFF CAN ID is 553 subscribed. E.g. in the example from above: 554 555 .. code-block:: C 556 557 rfilter[0].can_id = 0x123; 558 rfilter[0].can_mask = CAN_SFF_MASK; 559 560 both SFF frames with CAN ID 0x123 and EFF frames with 0xXXXXX123 can pass. 561 562 To filter for only 0x123 (SFF) and 0x12345678 (EFF) CAN identifiers the 563 filter has to be defined in this way to benefit from the optimized filters: 564 565 .. code-block:: C 566 567 struct can_filter rfilter[2]; 568 569 rfilter[0].can_id = 0x123; 570 rfilter[0].can_mask = (CAN_EFF_FLAG | CAN_RTR_FLAG | CAN_SFF_MASK); 571 rfilter[1].can_id = 0x12345678 | CAN_EFF_FLAG; 572 rfilter[1].can_mask = (CAN_EFF_FLAG | CAN_RTR_FLAG | CAN_EFF_MASK); 573 574 setsockopt(s, SOL_CAN_RAW, CAN_RAW_FILTER, &rfilter, sizeof(rfilter)); 575 576 577 RAW Socket Option CAN_RAW_ERR_FILTER 578 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 579 580 As described in :ref:`socketcan-network-problem-notifications` the CAN interface driver can generate so 581 called Error Message Frames that can optionally be passed to the user 582 application in the same way as other CAN frames. The possible 583 errors are divided into different error classes that may be filtered 584 using the appropriate error mask. To register for every possible 585 error condition CAN_ERR_MASK can be used as value for the error mask. 586 The values for the error mask are defined in linux/can/error.h: 587 588 .. code-block:: C 589 590 can_err_mask_t err_mask = ( CAN_ERR_TX_TIMEOUT | CAN_ERR_BUSOFF ); 591 592 setsockopt(s, SOL_CAN_RAW, CAN_RAW_ERR_FILTER, 593 &err_mask, sizeof(err_mask)); 594 595 596 RAW Socket Option CAN_RAW_LOOPBACK 597 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 598 599 To meet multi user needs the local loopback is enabled by default 600 (see :ref:`socketcan-local-loopback1` for details). But in some embedded use-cases 601 (e.g. when only one application uses the CAN bus) this loopback 602 functionality can be disabled (separately for each socket): 603 604 .. code-block:: C 605 606 int loopback = 0; /* 0 = disabled, 1 = enabled (default) */ 607 608 setsockopt(s, SOL_CAN_RAW, CAN_RAW_LOOPBACK, &loopback, sizeof(loopback)); 609 610 611 RAW socket option CAN_RAW_RECV_OWN_MSGS 612 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 613 614 When the local loopback is enabled, all the sent CAN frames are 615 looped back to the open CAN sockets that registered for the CAN 616 frames' CAN-ID on this given interface to meet the multi user 617 needs. The reception of the CAN frames on the same socket that was 618 sending the CAN frame is assumed to be unwanted and therefore 619 disabled by default. This default behaviour may be changed on 620 demand: 621 622 .. code-block:: C 623 624 int recv_own_msgs = 1; /* 0 = disabled (default), 1 = enabled */ 625 626 setsockopt(s, SOL_CAN_RAW, CAN_RAW_RECV_OWN_MSGS, 627 &recv_own_msgs, sizeof(recv_own_msgs)); 628 629 Note that reception of a socket's own CAN frames are subject to the same 630 filtering as other CAN frames (see :ref:`socketcan-rawfilter`). 631 632 .. _socketcan-rawfd: 633 634 RAW Socket Option CAN_RAW_FD_FRAMES 635 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 636 637 CAN FD support in CAN_RAW sockets can be enabled with a new socket option 638 CAN_RAW_FD_FRAMES which is off by default. When the new socket option is 639 not supported by the CAN_RAW socket (e.g. on older kernels), switching the 640 CAN_RAW_FD_FRAMES option returns the error -ENOPROTOOPT. 641 642 Once CAN_RAW_FD_FRAMES is enabled the application can send both CAN frames 643 and CAN FD frames. OTOH the application has to handle CAN and CAN FD frames 644 when reading from the socket: 645 646 .. code-block:: C 647 648 CAN_RAW_FD_FRAMES enabled: CAN_MTU and CANFD_MTU are allowed 649 CAN_RAW_FD_FRAMES disabled: only CAN_MTU is allowed (default) 650 651 Example: 652 653 .. code-block:: C 654 655 [ remember: CANFD_MTU == sizeof(struct canfd_frame) ] 656 657 struct canfd_frame cfd; 658 659 nbytes = read(s, &cfd, CANFD_MTU); 660 661 if (nbytes == CANFD_MTU) { 662 printf("got CAN FD frame with length %d\n", cfd.len); 663 /* cfd.flags contains valid data */ 664 } else if (nbytes == CAN_MTU) { 665 printf("got Classical CAN frame with length %d\n", cfd.len); 666 /* cfd.flags is undefined */ 667 } else { 668 fprintf(stderr, "read: invalid CAN(FD) frame\n"); 669 return 1; 670 } 671 672 /* the content can be handled independently from the received MTU size */ 673 674 printf("can_id: %X data length: %d data: ", cfd.can_id, cfd.len); 675 for (i = 0; i < cfd.len; i++) 676 printf("%02X ", cfd.data[i]); 677 678 When reading with size CANFD_MTU only returns CAN_MTU bytes that have 679 been received from the socket a Classical CAN frame has been read into the 680 provided CAN FD structure. Note that the canfd_frame.flags data field is 681 not specified in the struct can_frame and therefore it is only valid in 682 CANFD_MTU sized CAN FD frames. 683 684 Implementation hint for new CAN applications: 685 686 To build a CAN FD aware application use struct canfd_frame as basic CAN 687 data structure for CAN_RAW based applications. When the application is 688 executed on an older Linux kernel and switching the CAN_RAW_FD_FRAMES 689 socket option returns an error: No problem. You'll get Classical CAN frames 690 or CAN FD frames and can process them the same way. 691 692 When sending to CAN devices make sure that the device is capable to handle 693 CAN FD frames by checking if the device maximum transfer unit is CANFD_MTU. 694 The CAN device MTU can be retrieved e.g. with a SIOCGIFMTU ioctl() syscall. 695 696 697 RAW socket option CAN_RAW_JOIN_FILTERS 698 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 699 700 The CAN_RAW socket can set multiple CAN identifier specific filters that 701 lead to multiple filters in the af_can.c filter processing. These filters 702 are indenpendent from each other which leads to logical OR'ed filters when 703 applied (see :ref:`socketcan-rawfilter`). 704 705 This socket option joines the given CAN filters in the way that only CAN 706 frames are passed to user space that matched *all* given CAN filters. The 707 semantic for the applied filters is therefore changed to a logical AND. 708 709 This is useful especially when the filterset is a combination of filters 710 where the CAN_INV_FILTER flag is set in order to notch single CAN IDs or 711 CAN ID ranges from the incoming traffic. 712 713 714 Broadcast Manager Protocol Sockets (SOCK_DGRAM) 715 ----------------------------------------------- 716 717 The Broadcast Manager protocol provides a command based configuration 718 interface to filter and send (e.g. cyclic) CAN messages in kernel space. 719 720 Receive filters can be used to down sample frequent messages; detect events 721 such as message contents changes, packet length changes, and do time-out 722 monitoring of received messages. 723 724 Periodic transmission tasks of CAN frames or a sequence of CAN frames can be 725 created and modified at runtime; both the message content and the two 726 possible transmit intervals can be altered. 727 728 A BCM socket is not intended for sending individual CAN frames using the 729 struct can_frame as known from the CAN_RAW socket. Instead a special BCM 730 configuration message is defined. The basic BCM configuration message used 731 to communicate with the broadcast manager and the available operations are 732 defined in the linux/can/bcm.h include. The BCM message consists of a 733 message header with a command ('opcode') followed by zero or more CAN frames. 734 The broadcast manager sends responses to user space in the same form: 735 736 .. code-block:: C 737 738 struct bcm_msg_head { 739 __u32 opcode; /* command */ 740 __u32 flags; /* special flags */ 741 __u32 count; /* run 'count' times with ival1 */ 742 struct timeval ival1, ival2; /* count and subsequent interval */ 743 canid_t can_id; /* unique can_id for task */ 744 __u32 nframes; /* number of can_frames following */ 745 struct can_frame frames[0]; 746 }; 747 748 The aligned payload 'frames' uses the same basic CAN frame structure defined 749 at the beginning of :ref:`socketcan-rawfd` and in the include/linux/can.h include. All 750 messages to the broadcast manager from user space have this structure. 751 752 Note a CAN_BCM socket must be connected instead of bound after socket 753 creation (example without error checking): 754 755 .. code-block:: C 756 757 int s; 758 struct sockaddr_can addr; 759 struct ifreq ifr; 760 761 s = socket(PF_CAN, SOCK_DGRAM, CAN_BCM); 762 763 strcpy(ifr.ifr_name, "can0"); 764 ioctl(s, SIOCGIFINDEX, &ifr); 765 766 addr.can_family = AF_CAN; 767 addr.can_ifindex = ifr.ifr_ifindex; 768 769 connect(s, (struct sockaddr *)&addr, sizeof(addr)); 770 771 (..) 772 773 The broadcast manager socket is able to handle any number of in flight 774 transmissions or receive filters concurrently. The different RX/TX jobs are 775 distinguished by the unique can_id in each BCM message. However additional 776 CAN_BCM sockets are recommended to communicate on multiple CAN interfaces. 777 When the broadcast manager socket is bound to 'any' CAN interface (=> the 778 interface index is set to zero) the configured receive filters apply to any 779 CAN interface unless the sendto() syscall is used to overrule the 'any' CAN 780 interface index. When using recvfrom() instead of read() to retrieve BCM 781 socket messages the originating CAN interface is provided in can_ifindex. 782 783 784 Broadcast Manager Operations 785 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 786 787 The opcode defines the operation for the broadcast manager to carry out, 788 or details the broadcast managers response to several events, including 789 user requests. 790 791 Transmit Operations (user space to broadcast manager): 792 793 TX_SETUP: 794 Create (cyclic) transmission task. 795 796 TX_DELETE: 797 Remove (cyclic) transmission task, requires only can_id. 798 799 TX_READ: 800 Read properties of (cyclic) transmission task for can_id. 801 802 TX_SEND: 803 Send one CAN frame. 804 805 Transmit Responses (broadcast manager to user space): 806 807 TX_STATUS: 808 Reply to TX_READ request (transmission task configuration). 809 810 TX_EXPIRED: 811 Notification when counter finishes sending at initial interval 812 'ival1'. Requires the TX_COUNTEVT flag to be set at TX_SETUP. 813 814 Receive Operations (user space to broadcast manager): 815 816 RX_SETUP: 817 Create RX content filter subscription. 818 819 RX_DELETE: 820 Remove RX content filter subscription, requires only can_id. 821 822 RX_READ: 823 Read properties of RX content filter subscription for can_id. 824 825 Receive Responses (broadcast manager to user space): 826 827 RX_STATUS: 828 Reply to RX_READ request (filter task configuration). 829 830 RX_TIMEOUT: 831 Cyclic message is detected to be absent (timer ival1 expired). 832 833 RX_CHANGED: 834 BCM message with updated CAN frame (detected content change). 835 Sent on first message received or on receipt of revised CAN messages. 836 837 838 Broadcast Manager Message Flags 839 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 840 841 When sending a message to the broadcast manager the 'flags' element may 842 contain the following flag definitions which influence the behaviour: 843 844 SETTIMER: 845 Set the values of ival1, ival2 and count 846 847 STARTTIMER: 848 Start the timer with the actual values of ival1, ival2 849 and count. Starting the timer leads simultaneously to emit a CAN frame. 850 851 TX_COUNTEVT: 852 Create the message TX_EXPIRED when count expires 853 854 TX_ANNOUNCE: 855 A change of data by the process is emitted immediately. 856 857 TX_CP_CAN_ID: 858 Copies the can_id from the message header to each 859 subsequent frame in frames. This is intended as usage simplification. For 860 TX tasks the unique can_id from the message header may differ from the 861 can_id(s) stored for transmission in the subsequent struct can_frame(s). 862 863 RX_FILTER_ID: 864 Filter by can_id alone, no frames required (nframes=0). 865 866 RX_CHECK_DLC: 867 A change of the DLC leads to an RX_CHANGED. 868 869 RX_NO_AUTOTIMER: 870 Prevent automatically starting the timeout monitor. 871 872 RX_ANNOUNCE_RESUME: 873 If passed at RX_SETUP and a receive timeout occurred, a 874 RX_CHANGED message will be generated when the (cyclic) receive restarts. 875 876 TX_RESET_MULTI_IDX: 877 Reset the index for the multiple frame transmission. 878 879 RX_RTR_FRAME: 880 Send reply for RTR-request (placed in op->frames[0]). 881 882 CAN_FD_FRAME: 883 The CAN frames following the bcm_msg_head are struct canfd_frame's 884 885 Broadcast Manager Transmission Timers 886 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 887 888 Periodic transmission configurations may use up to two interval timers. 889 In this case the BCM sends a number of messages ('count') at an interval 890 'ival1', then continuing to send at another given interval 'ival2'. When 891 only one timer is needed 'count' is set to zero and only 'ival2' is used. 892 When SET_TIMER and START_TIMER flag were set the timers are activated. 893 The timer values can be altered at runtime when only SET_TIMER is set. 894 895 896 Broadcast Manager message sequence transmission 897 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 898 899 Up to 256 CAN frames can be transmitted in a sequence in the case of a cyclic 900 TX task configuration. The number of CAN frames is provided in the 'nframes' 901 element of the BCM message head. The defined number of CAN frames are added 902 as array to the TX_SETUP BCM configuration message: 903 904 .. code-block:: C 905 906 /* create a struct to set up a sequence of four CAN frames */ 907 struct { 908 struct bcm_msg_head msg_head; 909 struct can_frame frame[4]; 910 } mytxmsg; 911 912 (..) 913 mytxmsg.msg_head.nframes = 4; 914 (..) 915 916 write(s, &mytxmsg, sizeof(mytxmsg)); 917 918 With every transmission the index in the array of CAN frames is increased 919 and set to zero at index overflow. 920 921 922 Broadcast Manager Receive Filter Timers 923 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 924 925 The timer values ival1 or ival2 may be set to non-zero values at RX_SETUP. 926 When the SET_TIMER flag is set the timers are enabled: 927 928 ival1: 929 Send RX_TIMEOUT when a received message is not received again within 930 the given time. When START_TIMER is set at RX_SETUP the timeout detection 931 is activated directly - even without a former CAN frame reception. 932 933 ival2: 934 Throttle the received message rate down to the value of ival2. This 935 is useful to reduce messages for the application when the signal inside the 936 CAN frame is stateless as state changes within the ival2 period may get 937 lost. 938 939 Broadcast Manager Multiplex Message Receive Filter 940 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 941 942 To filter for content changes in multiplex message sequences an array of more 943 than one CAN frames can be passed in a RX_SETUP configuration message. The 944 data bytes of the first CAN frame contain the mask of relevant bits that 945 have to match in the subsequent CAN frames with the received CAN frame. 946 If one of the subsequent CAN frames is matching the bits in that frame data 947 mark the relevant content to be compared with the previous received content. 948 Up to 257 CAN frames (multiplex filter bit mask CAN frame plus 256 CAN 949 filters) can be added as array to the TX_SETUP BCM configuration message: 950 951 .. code-block:: C 952 953 /* usually used to clear CAN frame data[] - beware of endian problems! */ 954 #define U64_DATA(p) (*(unsigned long long*)(p)->data) 955 956 struct { 957 struct bcm_msg_head msg_head; 958 struct can_frame frame[5]; 959 } msg; 960 961 msg.msg_head.opcode = RX_SETUP; 962 msg.msg_head.can_id = 0x42; 963 msg.msg_head.flags = 0; 964 msg.msg_head.nframes = 5; 965 U64_DATA(&msg.frame[0]) = 0xFF00000000000000ULL; /* MUX mask */ 966 U64_DATA(&msg.frame[1]) = 0x01000000000000FFULL; /* data mask (MUX 0x01) */ 967 U64_DATA(&msg.frame[2]) = 0x0200FFFF000000FFULL; /* data mask (MUX 0x02) */ 968 U64_DATA(&msg.frame[3]) = 0x330000FFFFFF0003ULL; /* data mask (MUX 0x33) */ 969 U64_DATA(&msg.frame[4]) = 0x4F07FC0FF0000000ULL; /* data mask (MUX 0x4F) */ 970 971 write(s, &msg, sizeof(msg)); 972 973 974 Broadcast Manager CAN FD Support 975 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 976 977 The programming API of the CAN_BCM depends on struct can_frame which is 978 given as array directly behind the bcm_msg_head structure. To follow this 979 schema for the CAN FD frames a new flag 'CAN_FD_FRAME' in the bcm_msg_head 980 flags indicates that the concatenated CAN frame structures behind the 981 bcm_msg_head are defined as struct canfd_frame: 982 983 .. code-block:: C 984 985 struct { 986 struct bcm_msg_head msg_head; 987 struct canfd_frame frame[5]; 988 } msg; 989 990 msg.msg_head.opcode = RX_SETUP; 991 msg.msg_head.can_id = 0x42; 992 msg.msg_head.flags = CAN_FD_FRAME; 993 msg.msg_head.nframes = 5; 994 (..) 995 996 When using CAN FD frames for multiplex filtering the MUX mask is still 997 expected in the first 64 bit of the struct canfd_frame data section. 998 999 1000 Connected Transport Protocols (SOCK_SEQPACKET) 1001 ---------------------------------------------- 1002 1003 (to be written) 1004 1005 1006 Unconnected Transport Protocols (SOCK_DGRAM) 1007 -------------------------------------------- 1008 1009 (to be written) 1010 1011 1012 .. _socketcan-core-module: 1013 1014 SocketCAN Core Module 1015 ===================== 1016 1017 The SocketCAN core module implements the protocol family 1018 PF_CAN. CAN protocol modules are loaded by the core module at 1019 runtime. The core module provides an interface for CAN protocol 1020 modules to subscribe needed CAN IDs (see :ref:`socketcan-receive-lists`). 1021 1022 1023 can.ko Module Params 1024 -------------------- 1025 1026 - **stats_timer**: 1027 To calculate the SocketCAN core statistics 1028 (e.g. current/maximum frames per second) this 1 second timer is 1029 invoked at can.ko module start time by default. This timer can be 1030 disabled by using stattimer=0 on the module commandline. 1031 1032 - **debug**: 1033 (removed since SocketCAN SVN r546) 1034 1035 1036 procfs content 1037 -------------- 1038 1039 As described in :ref:`socketcan-receive-lists` the SocketCAN core uses several filter 1040 lists to deliver received CAN frames to CAN protocol modules. These 1041 receive lists, their filters and the count of filter matches can be 1042 checked in the appropriate receive list. All entries contain the 1043 device and a protocol module identifier:: 1044 1045 foo@bar:~$ cat /proc/net/can/rcvlist_all 1046 1047 receive list 'rx_all': 1048 (vcan3: no entry) 1049 (vcan2: no entry) 1050 (vcan1: no entry) 1051 device can_id can_mask function userdata matches ident 1052 vcan0 000 00000000 f88e6370 f6c6f400 0 raw 1053 (any: no entry) 1054 1055 In this example an application requests any CAN traffic from vcan0:: 1056 1057 rcvlist_all - list for unfiltered entries (no filter operations) 1058 rcvlist_eff - list for single extended frame (EFF) entries 1059 rcvlist_err - list for error message frames masks 1060 rcvlist_fil - list for mask/value filters 1061 rcvlist_inv - list for mask/value filters (inverse semantic) 1062 rcvlist_sff - list for single standard frame (SFF) entries 1063 1064 Additional procfs files in /proc/net/can:: 1065 1066 stats - SocketCAN core statistics (rx/tx frames, match ratios, ...) 1067 reset_stats - manual statistic reset 1068 version - prints SocketCAN core and ABI version (removed in Linux 5.10) 1069 1070 1071 Writing Own CAN Protocol Modules 1072 -------------------------------- 1073 1074 To implement a new protocol in the protocol family PF_CAN a new 1075 protocol has to be defined in include/linux/can.h . 1076 The prototypes and definitions to use the SocketCAN core can be 1077 accessed by including include/linux/can/core.h . 1078 In addition to functions that register the CAN protocol and the 1079 CAN device notifier chain there are functions to subscribe CAN 1080 frames received by CAN interfaces and to send CAN frames:: 1081 1082 can_rx_register - subscribe CAN frames from a specific interface 1083 can_rx_unregister - unsubscribe CAN frames from a specific interface 1084 can_send - transmit a CAN frame (optional with local loopback) 1085 1086 For details see the kerneldoc documentation in net/can/af_can.c or 1087 the source code of net/can/raw.c or net/can/bcm.c . 1088 1089 1090 CAN Network Drivers 1091 =================== 1092 1093 Writing a CAN network device driver is much easier than writing a 1094 CAN character device driver. Similar to other known network device 1095 drivers you mainly have to deal with: 1096 1097 - TX: Put the CAN frame from the socket buffer to the CAN controller. 1098 - RX: Put the CAN frame from the CAN controller to the socket buffer. 1099 1100 See e.g. at Documentation/networking/netdevices.rst . The differences 1101 for writing CAN network device driver are described below: 1102 1103 1104 General Settings 1105 ---------------- 1106 1107 .. code-block:: C 1108 1109 dev->type = ARPHRD_CAN; /* the netdevice hardware type */ 1110 dev->flags = IFF_NOARP; /* CAN has no arp */ 1111 1112 dev->mtu = CAN_MTU; /* sizeof(struct can_frame) -> Classical CAN interface */ 1113 1114 or alternative, when the controller supports CAN with flexible data rate: 1115 dev->mtu = CANFD_MTU; /* sizeof(struct canfd_frame) -> CAN FD interface */ 1116 1117 The struct can_frame or struct canfd_frame is the payload of each socket 1118 buffer (skbuff) in the protocol family PF_CAN. 1119 1120 1121 .. _socketcan-local-loopback2: 1122 1123 Local Loopback of Sent Frames 1124 ----------------------------- 1125 1126 As described in :ref:`socketcan-local-loopback1` the CAN network device driver should 1127 support a local loopback functionality similar to the local echo 1128 e.g. of tty devices. In this case the driver flag IFF_ECHO has to be 1129 set to prevent the PF_CAN core from locally echoing sent frames 1130 (aka loopback) as fallback solution:: 1131 1132 dev->flags = (IFF_NOARP | IFF_ECHO); 1133 1134 1135 CAN Controller Hardware Filters 1136 ------------------------------- 1137 1138 To reduce the interrupt load on deep embedded systems some CAN 1139 controllers support the filtering of CAN IDs or ranges of CAN IDs. 1140 These hardware filter capabilities vary from controller to 1141 controller and have to be identified as not feasible in a multi-user 1142 networking approach. The use of the very controller specific 1143 hardware filters could make sense in a very dedicated use-case, as a 1144 filter on driver level would affect all users in the multi-user 1145 system. The high efficient filter sets inside the PF_CAN core allow 1146 to set different multiple filters for each socket separately. 1147 Therefore the use of hardware filters goes to the category 'handmade 1148 tuning on deep embedded systems'. The author is running a MPC603e 1149 @133MHz with four SJA1000 CAN controllers from 2002 under heavy bus 1150 load without any problems ... 1151 1152 1153 Switchable Termination Resistors 1154 -------------------------------- 1155 1156 CAN bus requires a specific impedance across the differential pair, 1157 typically provided by two 120Ohm resistors on the farthest nodes of 1158 the bus. Some CAN controllers support activating / deactivating a 1159 termination resistor(s) to provide the correct impedance. 1160 1161 Query the available resistances:: 1162 1163 $ ip -details link show can0 1164 ... 1165 termination 120 [ 0, 120 ] 1166 1167 Activate the terminating resistor:: 1168 1169 $ ip link set dev can0 type can termination 120 1170 1171 Deactivate the terminating resistor:: 1172 1173 $ ip link set dev can0 type can termination 0 1174 1175 To enable termination resistor support to a can-controller, either 1176 implement in the controller's struct can-priv:: 1177 1178 termination_const 1179 termination_const_cnt 1180 do_set_termination 1181 1182 or add gpio control with the device tree entries from 1183 Documentation/devicetree/bindings/net/can/can-controller.yaml 1184 1185 1186 The Virtual CAN Driver (vcan) 1187 ----------------------------- 1188 1189 Similar to the network loopback devices, vcan offers a virtual local 1190 CAN interface. A full qualified address on CAN consists of 1191 1192 - a unique CAN Identifier (CAN ID) 1193 - the CAN bus this CAN ID is transmitted on (e.g. can0) 1194 1195 so in common use cases more than one virtual CAN interface is needed. 1196 1197 The virtual CAN interfaces allow the transmission and reception of CAN 1198 frames without real CAN controller hardware. Virtual CAN network 1199 devices are usually named 'vcanX', like vcan0 vcan1 vcan2 ... 1200 When compiled as a module the virtual CAN driver module is called vcan.ko 1201 1202 Since Linux Kernel version 2.6.24 the vcan driver supports the Kernel 1203 netlink interface to create vcan network devices. The creation and 1204 removal of vcan network devices can be managed with the ip(8) tool:: 1205 1206 - Create a virtual CAN network interface: 1207 $ ip link add type vcan 1208 1209 - Create a virtual CAN network interface with a specific name 'vcan42': 1210 $ ip link add dev vcan42 type vcan 1211 1212 - Remove a (virtual CAN) network interface 'vcan42': 1213 $ ip link del vcan42 1214 1215 1216 The CAN Network Device Driver Interface 1217 --------------------------------------- 1218 1219 The CAN network device driver interface provides a generic interface 1220 to setup, configure and monitor CAN network devices. The user can then 1221 configure the CAN device, like setting the bit-timing parameters, via 1222 the netlink interface using the program "ip" from the "IPROUTE2" 1223 utility suite. The following chapter describes briefly how to use it. 1224 Furthermore, the interface uses a common data structure and exports a 1225 set of common functions, which all real CAN network device drivers 1226 should use. Please have a look to the SJA1000 or MSCAN driver to 1227 understand how to use them. The name of the module is can-dev.ko. 1228 1229 1230 Netlink interface to set/get devices properties 1231 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1232 1233 The CAN device must be configured via netlink interface. The supported 1234 netlink message types are defined and briefly described in 1235 "include/linux/can/netlink.h". CAN link support for the program "ip" 1236 of the IPROUTE2 utility suite is available and it can be used as shown 1237 below: 1238 1239 Setting CAN device properties:: 1240 1241 $ ip link set can0 type can help 1242 Usage: ip link set DEVICE type can 1243 [ bitrate BITRATE [ sample-point SAMPLE-POINT] ] | 1244 [ tq TQ prop-seg PROP_SEG phase-seg1 PHASE-SEG1 1245 phase-seg2 PHASE-SEG2 [ sjw SJW ] ] 1246 1247 [ dbitrate BITRATE [ dsample-point SAMPLE-POINT] ] | 1248 [ dtq TQ dprop-seg PROP_SEG dphase-seg1 PHASE-SEG1 1249 dphase-seg2 PHASE-SEG2 [ dsjw SJW ] ] 1250 1251 [ loopback { on | off } ] 1252 [ listen-only { on | off } ] 1253 [ triple-sampling { on | off } ] 1254 [ one-shot { on | off } ] 1255 [ berr-reporting { on | off } ] 1256 [ fd { on | off } ] 1257 [ fd-non-iso { on | off } ] 1258 [ presume-ack { on | off } ] 1259 [ cc-len8-dlc { on | off } ] 1260 1261 [ restart-ms TIME-MS ] 1262 [ restart ] 1263 1264 Where: BITRATE := { 1..1000000 } 1265 SAMPLE-POINT := { 0.000..0.999 } 1266 TQ := { NUMBER } 1267 PROP-SEG := { 1..8 } 1268 PHASE-SEG1 := { 1..8 } 1269 PHASE-SEG2 := { 1..8 } 1270 SJW := { 1..4 } 1271 RESTART-MS := { 0 | NUMBER } 1272 1273 Display CAN device details and statistics:: 1274 1275 $ ip -details -statistics link show can0 1276 2: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 16 qdisc pfifo_fast state UP qlen 10 1277 link/can 1278 can <TRIPLE-SAMPLING> state ERROR-ACTIVE restart-ms 100 1279 bitrate 125000 sample_point 0.875 1280 tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1 1281 sja1000: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1 1282 clock 8000000 1283 re-started bus-errors arbit-lost error-warn error-pass bus-off 1284 41 17457 0 41 42 41 1285 RX: bytes packets errors dropped overrun mcast 1286 140859 17608 17457 0 0 0 1287 TX: bytes packets errors dropped carrier collsns 1288 861 112 0 41 0 0 1289 1290 More info to the above output: 1291 1292 "<TRIPLE-SAMPLING>" 1293 Shows the list of selected CAN controller modes: LOOPBACK, 1294 LISTEN-ONLY, or TRIPLE-SAMPLING. 1295 1296 "state ERROR-ACTIVE" 1297 The current state of the CAN controller: "ERROR-ACTIVE", 1298 "ERROR-WARNING", "ERROR-PASSIVE", "BUS-OFF" or "STOPPED" 1299 1300 "restart-ms 100" 1301 Automatic restart delay time. If set to a non-zero value, a 1302 restart of the CAN controller will be triggered automatically 1303 in case of a bus-off condition after the specified delay time 1304 in milliseconds. By default it's off. 1305 1306 "bitrate 125000 sample-point 0.875" 1307 Shows the real bit-rate in bits/sec and the sample-point in the 1308 range 0.000..0.999. If the calculation of bit-timing parameters 1309 is enabled in the kernel (CONFIG_CAN_CALC_BITTIMING=y), the 1310 bit-timing can be defined by setting the "bitrate" argument. 1311 Optionally the "sample-point" can be specified. By default it's 1312 0.000 assuming CIA-recommended sample-points. 1313 1314 "tq 125 prop-seg 6 phase-seg1 7 phase-seg2 2 sjw 1" 1315 Shows the time quanta in ns, propagation segment, phase buffer 1316 segment 1 and 2 and the synchronisation jump width in units of 1317 tq. They allow to define the CAN bit-timing in a hardware 1318 independent format as proposed by the Bosch CAN 2.0 spec (see 1319 chapter 8 of http://www.semiconductors.bosch.de/pdf/can2spec.pdf). 1320 1321 "sja1000: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1 clock 8000000" 1322 Shows the bit-timing constants of the CAN controller, here the 1323 "sja1000". The minimum and maximum values of the time segment 1 1324 and 2, the synchronisation jump width in units of tq, the 1325 bitrate pre-scaler and the CAN system clock frequency in Hz. 1326 These constants could be used for user-defined (non-standard) 1327 bit-timing calculation algorithms in user-space. 1328 1329 "re-started bus-errors arbit-lost error-warn error-pass bus-off" 1330 Shows the number of restarts, bus and arbitration lost errors, 1331 and the state changes to the error-warning, error-passive and 1332 bus-off state. RX overrun errors are listed in the "overrun" 1333 field of the standard network statistics. 1334 1335 Setting the CAN Bit-Timing 1336 ~~~~~~~~~~~~~~~~~~~~~~~~~~ 1337 1338 The CAN bit-timing parameters can always be defined in a hardware 1339 independent format as proposed in the Bosch CAN 2.0 specification 1340 specifying the arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" 1341 and "sjw":: 1342 1343 $ ip link set canX type can tq 125 prop-seg 6 \ 1344 phase-seg1 7 phase-seg2 2 sjw 1 1345 1346 If the kernel option CONFIG_CAN_CALC_BITTIMING is enabled, CIA 1347 recommended CAN bit-timing parameters will be calculated if the bit- 1348 rate is specified with the argument "bitrate":: 1349 1350 $ ip link set canX type can bitrate 125000 1351 1352 Note that this works fine for the most common CAN controllers with 1353 standard bit-rates but may *fail* for exotic bit-rates or CAN system 1354 clock frequencies. Disabling CONFIG_CAN_CALC_BITTIMING saves some 1355 space and allows user-space tools to solely determine and set the 1356 bit-timing parameters. The CAN controller specific bit-timing 1357 constants can be used for that purpose. They are listed by the 1358 following command:: 1359 1360 $ ip -details link show can0 1361 ... 1362 sja1000: clock 8000000 tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1 1363 1364 1365 Starting and Stopping the CAN Network Device 1366 ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ 1367 1368 A CAN network device is started or stopped as usual with the command 1369 "ifconfig canX up/down" or "ip link set canX up/down". Be aware that 1370 you *must* define proper bit-timing parameters for real CAN devices 1371 before you can start it to avoid error-prone default settings:: 1372 1373 $ ip link set canX up type can bitrate 125000 1374 1375 A device may enter the "bus-off" state if too many errors occurred on 1376 the CAN bus. Then no more messages are received or sent. An automatic 1377 bus-off recovery can be enabled by setting the "restart-ms" to a 1378 non-zero value, e.g.:: 1379 1380 $ ip link set canX type can restart-ms 100 1381 1382 Alternatively, the application may realize the "bus-off" condition 1383 by monitoring CAN error message frames and do a restart when 1384 appropriate with the command:: 1385 1386 $ ip link set canX type can restart 1387 1388 Note that a restart will also create a CAN error message frame (see 1389 also :ref:`socketcan-network-problem-notifications`). 1390 1391 1392 .. _socketcan-can-fd-driver: 1393 1394 CAN FD (Flexible Data Rate) Driver Support 1395 ------------------------------------------ 1396 1397 CAN FD capable CAN controllers support two different bitrates for the 1398 arbitration phase and the payload phase of the CAN FD frame. Therefore a 1399 second bit timing has to be specified in order to enable the CAN FD bitrate. 1400 1401 Additionally CAN FD capable CAN controllers support up to 64 bytes of 1402 payload. The representation of this length in can_frame.len and 1403 canfd_frame.len for userspace applications and inside the Linux network 1404 layer is a plain value from 0 .. 64 instead of the CAN 'data length code'. 1405 The data length code was a 1:1 mapping to the payload length in the Classical 1406 CAN frames anyway. The payload length to the bus-relevant DLC mapping is 1407 only performed inside the CAN drivers, preferably with the helper 1408 functions can_fd_dlc2len() and can_fd_len2dlc(). 1409 1410 The CAN netdevice driver capabilities can be distinguished by the network 1411 devices maximum transfer unit (MTU):: 1412 1413 MTU = 16 (CAN_MTU) => sizeof(struct can_frame) => Classical CAN device 1414 MTU = 72 (CANFD_MTU) => sizeof(struct canfd_frame) => CAN FD capable device 1415 1416 The CAN device MTU can be retrieved e.g. with a SIOCGIFMTU ioctl() syscall. 1417 N.B. CAN FD capable devices can also handle and send Classical CAN frames. 1418 1419 When configuring CAN FD capable CAN controllers an additional 'data' bitrate 1420 has to be set. This bitrate for the data phase of the CAN FD frame has to be 1421 at least the bitrate which was configured for the arbitration phase. This 1422 second bitrate is specified analogue to the first bitrate but the bitrate 1423 setting keywords for the 'data' bitrate start with 'd' e.g. dbitrate, 1424 dsample-point, dsjw or dtq and similar settings. When a data bitrate is set 1425 within the configuration process the controller option "fd on" can be 1426 specified to enable the CAN FD mode in the CAN controller. This controller 1427 option also switches the device MTU to 72 (CANFD_MTU). 1428 1429 The first CAN FD specification presented as whitepaper at the International 1430 CAN Conference 2012 needed to be improved for data integrity reasons. 1431 Therefore two CAN FD implementations have to be distinguished today: 1432 1433 - ISO compliant: The ISO 11898-1:2015 CAN FD implementation (default) 1434 - non-ISO compliant: The CAN FD implementation following the 2012 whitepaper 1435 1436 Finally there are three types of CAN FD controllers: 1437 1438 1. ISO compliant (fixed) 1439 2. non-ISO compliant (fixed, like the M_CAN IP core v3.0.1 in m_can.c) 1440 3. ISO/non-ISO CAN FD controllers (switchable, like the PEAK PCAN-USB FD) 1441 1442 The current ISO/non-ISO mode is announced by the CAN controller driver via 1443 netlink and displayed by the 'ip' tool (controller option FD-NON-ISO). 1444 The ISO/non-ISO-mode can be altered by setting 'fd-non-iso {on|off}' for 1445 switchable CAN FD controllers only. 1446 1447 Example configuring 500 kbit/s arbitration bitrate and 4 Mbit/s data bitrate:: 1448 1449 $ ip link set can0 up type can bitrate 500000 sample-point 0.75 \ 1450 dbitrate 4000000 dsample-point 0.8 fd on 1451 $ ip -details link show can0 1452 5: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UNKNOWN \ 1453 mode DEFAULT group default qlen 10 1454 link/can promiscuity 0 1455 can <FD> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 1456 bitrate 500000 sample-point 0.750 1457 tq 50 prop-seg 14 phase-seg1 15 phase-seg2 10 sjw 1 1458 pcan_usb_pro_fd: tseg1 1..64 tseg2 1..16 sjw 1..16 brp 1..1024 \ 1459 brp-inc 1 1460 dbitrate 4000000 dsample-point 0.800 1461 dtq 12 dprop-seg 7 dphase-seg1 8 dphase-seg2 4 dsjw 1 1462 pcan_usb_pro_fd: dtseg1 1..16 dtseg2 1..8 dsjw 1..4 dbrp 1..1024 \ 1463 dbrp-inc 1 1464 clock 80000000 1465 1466 Example when 'fd-non-iso on' is added on this switchable CAN FD adapter:: 1467 1468 can <FD,FD-NON-ISO> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0 1469 1470 1471 Supported CAN Hardware 1472 ---------------------- 1473 1474 Please check the "Kconfig" file in "drivers/net/can" to get an actual 1475 list of the support CAN hardware. On the SocketCAN project website 1476 (see :ref:`socketcan-resources`) there might be further drivers available, also for 1477 older kernel versions. 1478 1479 1480 .. _socketcan-resources: 1481 1482 SocketCAN Resources 1483 =================== 1484 1485 The Linux CAN / SocketCAN project resources (project site / mailing list) 1486 are referenced in the MAINTAINERS file in the Linux source tree. 1487 Search for CAN NETWORK [LAYERS|DRIVERS]. 1488 1489 Credits 1490 ======= 1491 1492 - Oliver Hartkopp (PF_CAN core, filters, drivers, bcm, SJA1000 driver) 1493 - Urs Thuermann (PF_CAN core, kernel integration, socket interfaces, raw, vcan) 1494 - Jan Kizka (RT-SocketCAN core, Socket-API reconciliation) 1495 - Wolfgang Grandegger (RT-SocketCAN core & drivers, Raw Socket-API reviews, CAN device driver interface, MSCAN driver) 1496 - Robert Schwebel (design reviews, PTXdist integration) 1497 - Marc Kleine-Budde (design reviews, Kernel 2.6 cleanups, drivers) 1498 - Benedikt Spranger (reviews) 1499 - Thomas Gleixner (LKML reviews, coding style, posting hints) 1500 - Andrey Volkov (kernel subtree structure, ioctls, MSCAN driver) 1501 - Matthias Brukner (first SJA1000 CAN netdevice implementation Q2/2003) 1502 - Klaus Hitschler (PEAK driver integration) 1503 - Uwe Koppe (CAN netdevices with PF_PACKET approach) 1504 - Michael Schulze (driver layer loopback requirement, RT CAN drivers review) 1505 - Pavel Pisa (Bit-timing calculation) 1506 - Sascha Hauer (SJA1000 platform driver) 1507 - Sebastian Haas (SJA1000 EMS PCI driver) 1508 - Markus Plessing (SJA1000 EMS PCI driver) 1509 - Per Dalen (SJA1000 Kvaser PCI driver) 1510 - Sam Ravnborg (reviews, coding style, kbuild help)
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.