1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Devicetree for the Samsung Galaxy Exhibit SGH-T599 also known as Codina-TMO,
4 * the "TMO" shall be read "T-Mobile" as this phone was produced exlusively
5 * for T-Mobile in the United States.
6 *
7 * This phone is closely related to the Codina, but has:
8 * - No CPU speed cap, full ~1GHz rate
9 * - Different power management IC, AB8505
10 * - As AB8505 has a micro USB phy, no TI TSU6111
11 * - Different power routing such as the removal of the external LDO for the
12 * touchscreen in favor of using the AB8505
13 * - Using a regulator for the key backlight LED
14 * - Using the Samsung S6D27A1 panel by default
15 * - The panel is using one of the ordinary AB8505 regulators for 1.8V
16 * - WiFi/Bluetooth combi chip upgraded to BCM4334
17 * - GPIO for backlight control moved from 68 to 69
18 */
19
20 /dts-v1/;
21 #include "ste-db8500.dtsi"
22 #include "ste-ab8505.dtsi"
23 #include "ste-dbx5x0-pinctrl.dtsi"
24 #include <dt-bindings/gpio/gpio.h>
25 #include <dt-bindings/leds/common.h>
26 #include <dt-bindings/input/input.h>
27 #include <dt-bindings/interrupt-controller/irq.h>
28
29 / {
30 model = "Samsung Galaxy Exhibit (SGH-T599)";
31 compatible = "samsung,codina-tmo", "st-ericsson,u8500";
32
33 chosen {
34 stdout-path = &serial2;
35 };
36
37 battery: battery {
38 compatible = "samsung,eb425161lu";
39 };
40
41 thermal-zones {
42 battery-thermal {
43 /* This zone will be polled by the battery temperature code */
44 polling-delay = <0>;
45 polling-delay-passive = <0>;
46 thermal-sensors = <&bat_therm>;
47
48 trips {
49 battery-crit-hi {
50 temperature = <70000>;
51 hysteresis = <2000>;
52 type = "critical";
53 };
54 };
55 };
56 };
57
58 bat_therm: thermistor {
59 compatible = "samsung,1404-001221";
60 io-channels = <&gpadc 0x02>; /* BatTemp */
61 pullup-uv = <1800000>;
62 pullup-ohm = <230000>;
63 pulldown-ohm = <0>;
64 #thermal-sensor-cells = <0>;
65 };
66
67 /* TI TXS0206 level translator for 2.9 V */
68 sd_level_translator: regulator-gpio {
69 compatible = "regulator-fixed";
70
71 /* GPIO87 EN */
72 gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
73 enable-active-high;
74
75 regulator-name = "sd-level-translator";
76 regulator-min-microvolt = <2900000>;
77 regulator-max-microvolt = <2900000>;
78 regulator-type = "voltage";
79
80 startup-delay-us = <200>;
81
82 pinctrl-names = "default";
83 pinctrl-0 = <&sd_level_translator_default>;
84 };
85
86 /* External LDO MIC5366-3.3YMT for eMMC */
87 ldo_3v3_reg: regulator-gpio-ldo-3v3 {
88 compatible = "regulator-fixed";
89 /* Supplied in turn by VBAT */
90 regulator-name = "VMEM_3V3";
91 regulator-min-microvolt = <3300000>;
92 regulator-max-microvolt = <3300000>;
93 gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
94 startup-delay-us = <5000>;
95 enable-active-high;
96 pinctrl-names = "default";
97 pinctrl-0 = <&emmc_ldo_en_default_mode>;
98 };
99
100 /*
101 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
102 * LCD_PWR_EN controls both the 3.0V output.
103 */
104 lcd_3v0_reg: regulator-gpio-lcd-3v0 {
105 compatible = "regulator-fixed";
106 /* Supplied in turn by VBAT */
107 regulator-name = "VREG_LCD_3.0V";
108 regulator-min-microvolt = <3000000>;
109 regulator-max-microvolt = <3000000>;
110 /* GPIO219 controls this regulator */
111 gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
112 enable-active-high;
113 pinctrl-names = "default";
114 pinctrl-0 = <&lcd_pwr_en_default_mode>;
115 };
116
117 /*
118 * This regulator is a GPIO line that drives the Broadcom WLAN
119 * line WL_REG_ON high and enables the internal regulators
120 * inside the chip. Unfortunatley it is erroneously named
121 * WLAN_RST_N on the schematic but it is not a reset line.
122 *
123 * The voltage specified here is only used to determine the OCR mask,
124 * the for the SDIO connector, the chip is actually connected
125 * directly to VBAT.
126 */
127 wl_reg: regulator-gpio-wlan {
128 compatible = "regulator-fixed";
129 regulator-name = "WL_REG_ON";
130 regulator-min-microvolt = <3000000>;
131 regulator-max-microvolt = <3000000>;
132 startup-delay-us = <100000>;
133 /* GPIO215 (WLAN_RST_N to WL_REG_ON) */
134 gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
135 enable-active-high;
136 pinctrl-names = "default";
137 pinctrl-0 = <&wlan_ldo_en_default>;
138 };
139
140 vibrator {
141 compatible = "gpio-vibrator";
142 /* GPIO195 "MOT_EN" */
143 enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
144 pinctrl-names = "default";
145 pinctrl-0 = <&vibrator_default>;
146 };
147
148 gpio-keys {
149 compatible = "gpio-keys";
150 pinctrl-names = "default";
151 pinctrl-0 = <&gpio_keys_default_mode>;
152
153 button-home {
154 linux,code = <KEY_HOME>;
155 label = "HOME";
156 /* GPIO91 */
157 gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
158 };
159 button-volup {
160 linux,code = <KEY_VOLUMEUP>;
161 label = "VOL+";
162 /* GPIO67 */
163 gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
164 };
165 button-voldown {
166 linux,code = <KEY_VOLUMEDOWN>;
167 label = "VOL-";
168 /* GPIO92 */
169 gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
170 };
171 };
172
173 led-touchkeys {
174 compatible = "regulator-led";
175 vled-supply = <&ab8500_ldo_aux4_reg>; // 3.3V
176 default-state = "on";
177 function = LED_FUNCTION_KBD_BACKLIGHT;
178 color = <LED_COLOR_ID_WHITE>;
179 };
180
181 ktd253: backlight {
182 compatible = "kinetic,ktd253";
183 /* GPIO69 is used on Codina R0.4 and Codina TMO */
184 enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
185 /* Default to 13/32 brightness */
186 default-brightness = <13>;
187 pinctrl-names = "default";
188 pinctrl-0 = <&ktd253_backlight_default_mode>;
189 };
190
191 /* Richtek RT8515GQW Flash LED Driver IC */
192 flash {
193 compatible = "richtek,rt8515";
194 /* GPIO 140 */
195 enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
196 /* GPIO 141 */
197 ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
198 /*
199 * RFS is 16 kOhm and RTS is 100 kOhm giving
200 * the flash max current 343mA and torch max
201 * current 55 mA.
202 */
203 richtek,rfs-ohms = <16000>;
204 richtek,rts-ohms = <100000>;
205 pinctrl-names = "default";
206 pinctrl-0 = <&gpio_flash_default_mode>;
207
208 led {
209 function = LED_FUNCTION_FLASH;
210 color = <LED_COLOR_ID_WHITE>;
211 flash-max-timeout-us = <250000>;
212 flash-max-microamp = <343750>;
213 led-max-microamp = <55000>;
214 };
215 };
216
217 /* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
218 i2c-gpio-0 {
219 compatible = "i2c-gpio";
220 sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
221 scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
222 pinctrl-names = "default";
223 pinctrl-0 = <&i2c_gpio_0_default>;
224 #address-cells = <1>;
225 #size-cells = <0>;
226
227 /* TODO: this should also be used by the SM5103 Camera power management unit */
228 };
229
230 /* Bit-banged I2C on GPIO151 and GPIO152 also called "COMP I2C" */
231 i2c-gpio-1 {
232 compatible = "i2c-gpio";
233 sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
234 scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
235 pinctrl-names = "default";
236 pinctrl-0 = <&i2c_gpio_1_default>;
237 #address-cells = <1>;
238 #size-cells = <0>;
239
240 magnetometer@c {
241 compatible = "alps,hscdtd008a";
242 reg = <0x0c>;
243 clock-frequency = <400000>;
244
245 avdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
246 dvdd-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
247 };
248 };
249
250 spi {
251 compatible = "spi-gpio";
252 /* Clock on GPIO220, pin SCL */
253 sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
254 /* MOSI on GPIO224, pin SDI "slave data in" */
255 mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
256 /* MISO on GPIO225, pin SDO "slave data out" */
257 miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
258 /* Chip select on GPIO201 */
259 cs-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
260 num-chipselects = <1>;
261
262 pinctrl-names = "default";
263 pinctrl-0 = <&spi_gpio_0_default>;
264 #address-cells = <1>;
265 #size-cells = <0>;
266
267 panel@0 {
268 compatible = "samsung,s6d27a1";
269 spi-max-frequency = <1200000>;
270 /* TYPE 3: inverse clock polarity and phase */
271 spi-cpha;
272 spi-cpol;
273
274 reg = <0>;
275 vci-supply = <&lcd_3v0_reg>;
276 vccio-supply = <&ab8500_ldo_aux6_reg>;
277
278 /* Reset on GPIO139 */
279 reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
280 /* LCD_VGH/LCD_DETECT, ESD IRQ on GPIO93 */
281 interrupt-parent = <&gpio2>;
282 interrupts = <29 IRQ_TYPE_EDGE_RISING>;
283
284 pinctrl-names = "default";
285 pinctrl-0 = <&panel_default_mode>;
286 backlight = <&ktd253>;
287
288 port {
289 panel_in: endpoint {
290 remote-endpoint = <&display_out>;
291 };
292 };
293 };
294 };
295
296 soc {
297 /* External Micro SD slot */
298 mmc@80126000 {
299 arm,primecell-periphid = <0x10480180>;
300 max-frequency = <100000000>;
301 bus-width = <4>;
302 cap-sd-highspeed;
303 cap-mmc-highspeed;
304 st,sig-pin-fbclk;
305 full-pwr-cycle;
306 /* MMC is powered by AUX3 1.2V .. 2.91V */
307 vmmc-supply = <&ab8500_ldo_aux3_reg>;
308 /* 2.9 V level translator is using AUX3 at 2.9 V as well */
309 vqmmc-supply = <&sd_level_translator>;
310 pinctrl-names = "default", "sleep";
311 pinctrl-0 = <&mc0_a_2_default>;
312 pinctrl-1 = <&mc0_a_2_sleep>;
313 cd-gpios = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
314 status = "okay";
315 };
316
317 /* WLAN SDIO channel */
318 mmc@80118000 {
319 arm,primecell-periphid = <0x10480180>;
320 max-frequency = <50000000>;
321 bus-width = <4>;
322 non-removable;
323 cap-sd-highspeed;
324 pinctrl-names = "default", "sleep";
325 pinctrl-0 = <&mc1_a_2_default>;
326 pinctrl-1 = <&mc1_a_2_sleep>;
327 /*
328 * GPIO-controlled voltage enablement: this drives
329 * the WL_REG_ON line high when we use this device.
330 * Represented as regulator to fill OCR mask.
331 */
332 vmmc-supply = <&wl_reg>;
333
334 #address-cells = <1>;
335 #size-cells = <0>;
336 status = "okay";
337
338 wifi@1 {
339 compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
340 reg = <1>;
341 /* GPIO216 WL_HOST_WAKE */
342 interrupt-parent = <&gpio6>;
343 interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
344 interrupt-names = "host-wake";
345 pinctrl-names = "default";
346 pinctrl-0 = <&wlan_default_mode>;
347 };
348 };
349
350 /* eMMC */
351 mmc@80005000 {
352 arm,primecell-periphid = <0x10480180>;
353 max-frequency = <100000000>;
354 bus-width = <8>;
355 non-removable;
356 cap-mmc-highspeed;
357 mmc-ddr-1_8v;
358 no-sdio;
359 no-sd;
360 vmmc-supply = <&ldo_3v3_reg>;
361 pinctrl-names = "default", "sleep";
362 /*
363 * GPIO130 will be set to input no pull-up resulting in a resistor
364 * pulling the reset high and taking the memory out of reset.
365 */
366 pinctrl-0 = <&mc2_a_1_default>;
367 pinctrl-1 = <&mc2_a_1_sleep>;
368 status = "okay";
369 };
370
371 /* GBF (Bluetooth) UART */
372 serial@80120000 {
373 pinctrl-names = "default", "sleep";
374 pinctrl-0 = <&u0_a_1_default>;
375 pinctrl-1 = <&u0_a_1_sleep>;
376 status = "okay";
377
378 bluetooth {
379 /* BCM4334B0 actually */
380 compatible = "brcm,bcm4330-bt";
381 /* GPIO222 rail BT_VREG_EN to BT_REG_ON */
382 shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
383 /* BT_WAKE on GPIO199 */
384 device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
385 /* BT_HOST_WAKE on GPIO97 */
386 /* FIXME: convert to interrupt */
387 host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
388 /* BT_RST_N on GPIO209 */
389 reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
390 pinctrl-names = "default";
391 pinctrl-0 = <&bluetooth_default_mode>;
392 };
393 };
394
395 /* GPS UART */
396 serial@80121000 {
397 status = "okay";
398 pinctrl-names = "default", "sleep";
399 /* CTS/RTS is not used, CTS is repurposed as GPIO */
400 pinctrl-0 = <&u1rxtx_a_1_default>;
401 pinctrl-1 = <&u1rxtx_a_1_sleep>;
402 /* FIXME: add a device for the GPS here */
403 };
404
405 /* Debugging console UART connected to AB8505 */
406 serial@80007000 {
407 status = "okay";
408 pinctrl-names = "default", "sleep";
409 pinctrl-0 = <&u2rxtx_c_1_default>;
410 pinctrl-1 = <&u2rxtx_c_1_sleep>;
411 };
412
413 prcmu@80157000 {
414 ab8505 {
415 phy {
416 pinctrl-names = "default", "sleep";
417 pinctrl-0 = <&usb_a_1_default>;
418 pinctrl-1 = <&usb_a_1_sleep>;
419 };
420
421 ab8500_fg {
422 line-impedance-micro-ohms = <36000>;
423 };
424
425 /* This is mostly identical to the Codina v0.4 regulators */
426 regulator {
427 ab8500_ldo_aux1 {
428 regulator-name = "v-sensors-vdd";
429 regulator-min-microvolt = <3000000>;
430 regulator-max-microvolt = <3300000>;
431 };
432
433 ab8500_ldo_aux2 {
434 regulator-name = "v-aux2";
435 regulator-min-microvolt = <3300000>;
436 regulator-max-microvolt = <3300000>;
437 };
438
439 ab8500_ldo_aux3 {
440 regulator-name = "v-mmc-sd";
441 };
442
443 ab8500_ldo_aux4 {
444 regulator-name = "v-aux4";
445 /*
446 * Providing some span here makes the touchkey
447 * LEDs actually dimmable.
448 */
449 regulator-min-microvolt = <1100000>;
450 regulator-max-microvolt = <3300000>;
451 };
452
453 ab8500_ldo_aux5 {
454 regulator-name = "v-aux5";
455 regulator-min-microvolt = <1800000>;
456 regulator-max-microvolt = <1800000>;
457 };
458
459 ab8500_ldo_aux6 {
460 /* 1.8 V to the display */
461 regulator-name = "v-aux6";
462 regulator-min-microvolt = <1800000>;
463 regulator-max-microvolt = <1800000>;
464 };
465
466 ab8500_ldo_aux8 {
467 regulator-name = "v-sensors-vio";
468 };
469 };
470 };
471 };
472
473 /* I2C0 also known as "AGC I2C" */
474 i2c@80004000 {
475 status = "okay";
476 pinctrl-names = "default", "sleep";
477 pinctrl-0 = <&i2c0_a_1_default>;
478 pinctrl-1 = <&i2c0_a_1_sleep>;
479
480 proximity@39 {
481 /* Codina has the Amstaos TMD2672 */
482 compatible = "amstaos,tmd2672";
483 clock-frequency = <400000>;
484 reg = <0x39>;
485
486 /* IRQ on GPIO146 "PS_INT" */
487 interrupt-parent = <&gpio4>;
488 interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
489 vdd-supply = <&ab8500_ldo_aux1_reg>;
490 vddio-supply = <&ab8500_ldo_aux8_reg>;
491 pinctrl-names = "default";
492 pinctrl-0 = <&tmd2672_codina_default>;
493 };
494 };
495
496 /* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
497 i2c@80128000 {
498 status = "okay";
499 pinctrl-names = "default", "sleep";
500 pinctrl-0 = <&i2c2_b_2_default>;
501 pinctrl-1 = <&i2c2_b_2_sleep>;
502
503 /* Bosch BMA254 accelerometer */
504 accelerometer@18 {
505 compatible = "bosch,bma254";
506 reg = <0x18>;
507 mount-matrix = "0", "1", "0",
508 "-1", "0", "0",
509 "0", "0", "1";
510 vddio-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
511 vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
512 };
513 };
514
515 /* I2C3 */
516 i2c@80110000 {
517 status = "okay";
518
519 pinctrl-names = "default", "sleep";
520 pinctrl-0 = <&i2c3_c_2_default>;
521 pinctrl-1 = <&i2c3_c_2_sleep>;
522
523 /* TODO: write bindings and driver for this touchscreen */
524
525 /* Zinitix BT404 ISP part */
526 isp@50 {
527 compatible = "zinitix,bt404-isp";
528 reg = <0x50>;
529 pinctrl-names = "default";
530 pinctrl-0 = <&tsp_default>;
531 };
532
533 /* Zinitix BT404 touchscreen, also has the touchkeys for menu and back */
534 touchscreen@20 {
535 compatible = "zinitix,bt404";
536 reg = <0x20>;
537 /* GPIO218 (TSP_INT_1V8) */
538 interrupt-parent = <&gpio6>;
539 interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
540 vcca-supply = <&ab8500_ldo_aux2_reg>; // 3.3V
541 vdd-supply = <&ab8500_ldo_aux5_reg>; // 1.8V
542 zinitix,mode = <2>;
543 touchscreen-size-x = <480>;
544 touchscreen-size-y = <800>;
545 pinctrl-names = "default";
546 pinctrl-0 = <&tsp_default>;
547 };
548 };
549
550 mcde@a0350000 {
551 status = "okay";
552 pinctrl-names = "default";
553 pinctrl-0 = <&dpi_default_mode>;
554
555 port {
556 display_out: endpoint {
557 remote-endpoint = <&panel_in>;
558 };
559 };
560 };
561 };
562 };
563
564 &pinctrl {
565 /*
566 * This extends the MC0_A_2 default config to include
567 * the card detect GPIO217 line.
568 */
569 sdi0 {
570 mc0_a_2_default {
571 default_cfg4 {
572 pins = "GPIO217_AH12"; /* card detect */
573 ste,config = <&gpio_in_pd>;
574 };
575 };
576 };
577 sdi2 {
578 /*
579 * GPIO130 should be set in GPIO mode and
580 * pulled down. (Not connected.)
581 */
582 mc2_a_1_default {
583 default_cfg2 {
584 pins = "GPIO130_C8"; /* FBCLK */
585 ste,config = <&gpio_in_pd>;
586 };
587 };
588 };
589 /* GPIO that enables the 2.9V SD card level translator */
590 sd-level-translator {
591 sd_level_translator_default: sd_level_translator_default {
592 /* level shifter on GPIO87 */
593 codina_cfg1 {
594 pins = "GPIO87_B3";
595 ste,config = <&gpio_out_hi>;
596 };
597 };
598 };
599 /* GPIO that enables the LDO regulator for the eMMC */
600 emmc-ldo {
601 emmc_ldo_en_default_mode: emmc_ldo_default {
602 /* LDO enable on GPIO223 */
603 codina_cfg1 {
604 pins = "GPIO223_AH9";
605 ste,config = <&gpio_out_hi>;
606 };
607 };
608 };
609 /* GPIOs for panel control */
610 panel {
611 panel_default_mode: panel_default {
612 codina_cfg1 {
613 /* Reset line */
614 pins = "GPIO139_C9";
615 ste,config = <&gpio_out_lo>;
616 };
617 codina_cfg2 {
618 /* ESD IRQ line "LCD detect" */
619 pins = "GPIO93_B7";
620 ste,config = <&gpio_in_nopull>;
621 };
622 };
623 };
624 /* GPIO that enables the LDO regulator for the LCD display */
625 lcd-ldo {
626 lcd_pwr_en_default_mode: lcd_pwr_en_default {
627 /* LCD_PWR_EN on GPIO219 */
628 codina_cfg1 {
629 pins = "GPIO219_AG10";
630 ste,config = <&gpio_out_hi>;
631 };
632 };
633 };
634 /* GPIO that enables the WLAN internal LDO regulators */
635 wlan-ldo {
636 wlan_ldo_en_default: wlan_ldo_default {
637 /* GPIO215 named WLAN_RST_N */
638 codina_cfg1 {
639 pins = "GPIO215_AH13";
640 ste,config = <&gpio_out_lo>;
641 };
642 };
643 };
644 /* Backlight GPIO */
645 backlight {
646 ktd253_backlight_default_mode: backlight_default {
647 skomer_cfg1 {
648 pins = "GPIO69_E2"; /* LCD_BL_CTRL */
649 ste,config = <&gpio_out_lo>;
650 };
651 };
652 };
653 /* Flash and torch */
654 flash {
655 gpio_flash_default_mode: flash_default {
656 codina_cfg1 {
657 pins = "GPIO140_B11", "GPIO141_C12";
658 ste,config = <&gpio_out_lo>;
659 };
660 };
661 };
662 /* GPIO keys */
663 gpio-keys {
664 gpio_keys_default_mode: gpio_keys_default {
665 skomer_cfg1 {
666 pins = "GPIO67_G2", /* VOL UP */
667 "GPIO91_B6", /* HOME */
668 "GPIO92_D6"; /* VOL DOWN */
669 ste,config = <&gpio_in_pu>;
670 };
671 };
672 };
673 /* Interrupt line for the Zinitix BT404 touchscreen */
674 tsp {
675 tsp_default: tsp_default {
676 codina_cfg1 {
677 pins = "GPIO218_AH11"; /* TSP_INT_1V8 */
678 ste,config = <&gpio_in_nopull>;
679 };
680 };
681 };
682 /* Interrupt line for light/proximity sensor TMD2672 */
683 tmd2672 {
684 tmd2672_codina_default: tmd2672_codina {
685 codina_cfg1 {
686 pins = "GPIO146_D13";
687 ste,config = <&gpio_in_nopull>;
688 };
689 };
690 };
691 /* GPIO-based I2C bus for subpmu */
692 i2c-gpio-0 {
693 i2c_gpio_0_default: i2c_gpio_0 {
694 codina_cfg1 {
695 pins = "GPIO143_D12", "GPIO144_B13";
696 ste,config = <&gpio_in_nopull>;
697 };
698 };
699 };
700 /* GPIO-based I2C bus for the NFC */
701 i2c-gpio-1 {
702 i2c_gpio_1_default: i2c_gpio_1 {
703 codina_cfg1 {
704 pins = "GPIO151_D17", "GPIO152_D16";
705 ste,config = <&gpio_in_nopull>;
706 };
707 };
708 };
709 /* GPIO-based SPI bus for the display */
710 spi-gpio-0 {
711 spi_gpio_0_default: spi_gpio_0_d {
712 codina_cfg1 {
713 pins = "GPIO220_AH10", "GPIO201_AF24", "GPIO224_AG9";
714 ste,config = <&gpio_out_hi>;
715 };
716 codina_cfg2 {
717 pins = "GPIO225_AG8";
718 /* Needs pull down, no pull down resistor on board */
719 ste,config = <&gpio_in_pd>;
720 };
721 };
722 spi_gpio_0_sleep: spi_gpio_0_s {
723 codina_cfg1 {
724 pins = "GPIO220_AH10", "GPIO201_AF24",
725 "GPIO224_AG9", "GPIO225_AG8";
726 ste,config = <&gpio_out_hi>;
727 };
728 };
729 };
730 wlan {
731 wlan_default_mode: wlan_default {
732 /* GPIO216 for WL_HOST_WAKE */
733 codina_cfg2 {
734 pins = "GPIO216_AG12";
735 ste,config = <&gpio_in_pd>;
736 };
737 };
738 };
739 bluetooth {
740 bluetooth_default_mode: bluetooth_default {
741 /* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
742 codina_cfg1 {
743 pins = "GPIO199_AH23", "GPIO222_AJ9";
744 ste,config = <&gpio_out_lo>;
745 };
746 /* GPIO97 BT_HOST_WAKE */
747 codina_cfg2 {
748 pins = "GPIO97_D9";
749 ste,config = <&gpio_in_nopull>;
750 };
751 /* GPIO209 BT_RST_N */
752 codina_cfg3 {
753 pins = "GPIO209_AG15";
754 ste,config = <&gpio_out_hi>;
755 };
756 };
757 };
758 vibrator {
759 vibrator_default: vibrator_default {
760 codina_cfg1 {
761 pins = "GPIO195_AG28"; /* MOT_EN */
762 ste,config = <&gpio_out_lo>;
763 };
764 };
765 };
766 mcde {
767 dpi_default_mode: dpi_default {
768 default_mux1 {
769 /* Mux in all the data lines */
770 function = "lcd";
771 groups =
772 /* Data lines D0-D7 GPIO70..GPIO77 */
773 "lcd_d0_d7_a_1",
774 /* Data lines D8-D11 GPIO78..GPIO81 */
775 "lcd_d8_d11_a_1",
776 /* Data lines D12-D15 GPIO82..GPIO85 */
777 "lcd_d12_d15_a_1",
778 /* Data lines D16-D23 GPIO161..GPIO168 */
779 "lcd_d16_d23_b_1";
780 };
781 default_mux2 {
782 function = "lcda";
783 /* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
784 groups = "lcdaclk_b_1", "lcda_b_1";
785 };
786 /* Input, no pull-up is the default state for pins used for an alt function */
787 default_cfg1 {
788 pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
789 ste,config = <&in_nopull>;
790 };
791 };
792 };
793 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.