1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
4 *
5 * Based on "omap4.dtsi"
6 */
7
8 #include <dt-bindings/bus/ti-sysc.h>
9 #include <dt-bindings/clock/dra7.h>
10 #include <dt-bindings/interrupt-controller/arm-gic.h>
11 #include <dt-bindings/pinctrl/dra.h>
12 #include <dt-bindings/clock/dra7.h>
13
14 #define MAX_SOURCES 400
15
16 / {
17 #address-cells = <2>;
18 #size-cells = <2>;
19
20 compatible = "ti,dra7xx";
21 interrupt-parent = <&crossbar_mpu>;
22 chosen { };
23
24 aliases {
25 i2c0 = &i2c1;
26 i2c1 = &i2c2;
27 i2c2 = &i2c3;
28 i2c3 = &i2c4;
29 i2c4 = &i2c5;
30 serial0 = &uart1;
31 serial1 = &uart2;
32 serial2 = &uart3;
33 serial3 = &uart4;
34 serial4 = &uart5;
35 serial5 = &uart6;
36 serial6 = &uart7;
37 serial7 = &uart8;
38 serial8 = &uart9;
39 serial9 = &uart10;
40 ethernet0 = &cpsw_port1;
41 ethernet1 = &cpsw_port2;
42 d_can0 = &dcan1;
43 d_can1 = &dcan2;
44 spi0 = &qspi;
45 };
46
47 timer {
48 compatible = "arm,armv7-timer";
49 status = "disabled"; /* See ARM architected timer wrap erratum i940 */
50 interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
51 <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
52 <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
53 <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
54 interrupt-parent = <&gic>;
55 };
56
57 gic: interrupt-controller@48211000 {
58 compatible = "arm,cortex-a15-gic";
59 interrupt-controller;
60 #interrupt-cells = <3>;
61 reg = <0x0 0x48211000 0x0 0x1000>,
62 <0x0 0x48212000 0x0 0x2000>,
63 <0x0 0x48214000 0x0 0x2000>,
64 <0x0 0x48216000 0x0 0x2000>;
65 interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
66 interrupt-parent = <&gic>;
67 };
68
69 wakeupgen: interrupt-controller@48281000 {
70 compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
71 interrupt-controller;
72 #interrupt-cells = <3>;
73 reg = <0x0 0x48281000 0x0 0x1000>;
74 interrupt-parent = <&gic>;
75 };
76
77 cpus {
78 #address-cells = <1>;
79 #size-cells = <0>;
80
81 cpu0: cpu@0 {
82 device_type = "cpu";
83 compatible = "arm,cortex-a15";
84 reg = <0>;
85
86 operating-points-v2 = <&cpu0_opp_table>;
87
88 clocks = <&dpll_mpu_ck>;
89 clock-names = "cpu";
90
91 clock-latency = <300000>; /* From omap-cpufreq driver */
92
93 /* cooling options */
94 #cooling-cells = <2>; /* min followed by max */
95
96 vbb-supply = <&abb_mpu>;
97 };
98 };
99
100 cpu0_opp_table: opp-table {
101 compatible = "operating-points-v2-ti-cpu";
102 syscon = <&scm_wkup>;
103
104 opp-1000000000 {
105 /* OPP NOM */
106 opp-hz = /bits/ 64 <1000000000>;
107 opp-microvolt = <1060000 850000 1150000>,
108 <1060000 850000 1150000>;
109 opp-supported-hw = <0xFF 0x01>;
110 opp-suspend;
111 };
112
113 opp-1176000000 {
114 /* OPP OD */
115 opp-hz = /bits/ 64 <1176000000>;
116 opp-microvolt = <1160000 885000 1160000>,
117 <1160000 885000 1160000>;
118
119 opp-supported-hw = <0xFF 0x02>;
120 };
121
122 opp-1500000000 {
123 /* OPP High */
124 opp-hz = /bits/ 64 <1500000000>;
125 opp-microvolt = <1210000 950000 1250000>,
126 <1210000 950000 1250000>;
127 opp-supported-hw = <0xFF 0x04>;
128 };
129 };
130
131 /*
132 * XXX: Use a flat representation of the SOC interconnect.
133 * The real OMAP interconnect network is quite complex.
134 * Since it will not bring real advantage to represent that in DT for
135 * the moment, just use a fake OCP bus entry to represent the whole bus
136 * hierarchy.
137 */
138 ocp: ocp {
139 compatible = "simple-pm-bus";
140 power-domains = <&prm_core>;
141 clocks = <&l3main1_clkctrl DRA7_L3MAIN1_L3_MAIN_1_CLKCTRL 0>,
142 <&l3instr_clkctrl DRA7_L3INSTR_L3_MAIN_2_CLKCTRL 0>;
143 #address-cells = <1>;
144 #size-cells = <1>;
145 ranges = <0x0 0x0 0x0 0xc0000000>;
146 dma-ranges = <0x80000000 0x0 0x80000000 0x80000000>;
147
148 l3-noc@44000000 {
149 compatible = "ti,dra7-l3-noc";
150 reg = <0x44000000 0x1000000>,
151 <0x45000000 0x1000>;
152 interrupts-extended = <&crossbar_mpu GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
153 <&wakeupgen GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
154 };
155
156 l4_cfg: interconnect@4a000000 {
157 };
158 l4_wkup: interconnect@4ae00000 {
159 };
160 l4_per1: interconnect@48000000 {
161 };
162
163 target-module@48210000 {
164 compatible = "ti,sysc-omap4-simple", "ti,sysc";
165 power-domains = <&prm_mpu>;
166 clocks = <&mpu_clkctrl DRA7_MPU_MPU_CLKCTRL 0>;
167 clock-names = "fck";
168 #address-cells = <1>;
169 #size-cells = <1>;
170 ranges = <0 0x48210000 0x1f0000>;
171
172 mpu {
173 compatible = "ti,omap5-mpu";
174 };
175 };
176
177 l4_per2: interconnect@48400000 {
178 };
179 l4_per3: interconnect@48800000 {
180 };
181
182 /*
183 * Register access seems to have complex dependencies and also
184 * seems to need an enabled phy. See the TRM chapter for "Table
185 * 26-678. Main Sequence PCIe Controller Global Initialization"
186 * and also dra7xx_pcie_probe().
187 */
188 axi0: target-module@51000000 {
189 compatible = "ti,sysc-omap4", "ti,sysc";
190 power-domains = <&prm_l3init>;
191 resets = <&prm_l3init 0>;
192 reset-names = "rstctrl";
193 clocks = <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 0>,
194 <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 9>,
195 <&pcie_clkctrl DRA7_PCIE_PCIE1_CLKCTRL 10>;
196 clock-names = "fck", "phy-clk", "phy-clk-div";
197 #size-cells = <1>;
198 #address-cells = <1>;
199 ranges = <0x51000000 0x51000000 0x3000>,
200 <0x20000000 0x20000000 0x10000000>;
201 dma-ranges;
202 /**
203 * To enable PCI endpoint mode, disable the pcie1_rc
204 * node and enable pcie1_ep mode.
205 */
206 pcie1_rc: pcie@51000000 {
207 reg = <0x51000000 0x2000>,
208 <0x51002000 0x14c>,
209 <0x20001000 0x2000>;
210 reg-names = "rc_dbics", "ti_conf", "config";
211 interrupts = <0 232 0x4>, <0 233 0x4>;
212 #address-cells = <3>;
213 #size-cells = <2>;
214 device_type = "pci";
215 ranges = <0x81000000 0 0x00000000 0x20003000 0 0x00010000>,
216 <0x82000000 0 0x20013000 0x20013000 0 0x0ffed000>;
217 bus-range = <0x00 0xff>;
218 #interrupt-cells = <1>;
219 num-lanes = <1>;
220 linux,pci-domain = <0>;
221 phys = <&pcie1_phy>;
222 phy-names = "pcie-phy0";
223 ti,syscon-lane-sel = <&scm_conf_pcie 0x18>;
224 interrupt-map-mask = <0 0 0 7>;
225 interrupt-map = <0 0 0 1 &pcie1_intc 1>,
226 <0 0 0 2 &pcie1_intc 2>,
227 <0 0 0 3 &pcie1_intc 3>,
228 <0 0 0 4 &pcie1_intc 4>;
229 ti,syscon-unaligned-access = <&scm_conf1 0x14 1>;
230 status = "disabled";
231 pcie1_intc: interrupt-controller {
232 interrupt-controller;
233 #address-cells = <0>;
234 #interrupt-cells = <1>;
235 };
236 };
237
238 pcie1_ep: pcie_ep@51000000 {
239 reg = <0x51000000 0x28>,
240 <0x51002000 0x14c>,
241 <0x51001000 0x28>,
242 <0x20001000 0x10000000>;
243 reg-names = "ep_dbics", "ti_conf", "ep_dbics2", "addr_space";
244 interrupts = <0 232 0x4>;
245 num-lanes = <1>;
246 num-ib-windows = <4>;
247 num-ob-windows = <16>;
248 phys = <&pcie1_phy>;
249 phy-names = "pcie-phy0";
250 ti,syscon-unaligned-access = <&scm_conf1 0x14 1>;
251 ti,syscon-lane-sel = <&scm_conf_pcie 0x18>;
252 status = "disabled";
253 };
254 };
255
256 /*
257 * Register access seems to have complex dependencies and also
258 * seems to need an enabled phy. See the TRM chapter for "Table
259 * 26-678. Main Sequence PCIe Controller Global Initialization"
260 * and also dra7xx_pcie_probe().
261 */
262 axi1: target-module@51800000 {
263 compatible = "ti,sysc-omap4", "ti,sysc";
264 clocks = <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 0>,
265 <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 9>,
266 <&pcie_clkctrl DRA7_PCIE_PCIE2_CLKCTRL 10>;
267 clock-names = "fck", "phy-clk", "phy-clk-div";
268 power-domains = <&prm_l3init>;
269 resets = <&prm_l3init 1>;
270 reset-names = "rstctrl";
271 #size-cells = <1>;
272 #address-cells = <1>;
273 ranges = <0x51800000 0x51800000 0x3000>,
274 <0x30000000 0x30000000 0x10000000>;
275 dma-ranges;
276 status = "disabled";
277 pcie2_rc: pcie@51800000 {
278 reg = <0x51800000 0x2000>,
279 <0x51802000 0x14c>,
280 <0x30001000 0x2000>;
281 reg-names = "rc_dbics", "ti_conf", "config";
282 interrupts = <0 355 0x4>, <0 356 0x4>;
283 #address-cells = <3>;
284 #size-cells = <2>;
285 device_type = "pci";
286 ranges = <0x81000000 0 0x00000000 0x30003000 0 0x00010000>,
287 <0x82000000 0 0x30013000 0x30013000 0 0x0ffed000>;
288 bus-range = <0x00 0xff>;
289 #interrupt-cells = <1>;
290 num-lanes = <1>;
291 linux,pci-domain = <1>;
292 phys = <&pcie2_phy>;
293 phy-names = "pcie-phy0";
294 interrupt-map-mask = <0 0 0 7>;
295 interrupt-map = <0 0 0 1 &pcie2_intc 1>,
296 <0 0 0 2 &pcie2_intc 2>,
297 <0 0 0 3 &pcie2_intc 3>,
298 <0 0 0 4 &pcie2_intc 4>;
299 ti,syscon-unaligned-access = <&scm_conf1 0x14 2>;
300 pcie2_intc: interrupt-controller {
301 interrupt-controller;
302 #address-cells = <0>;
303 #interrupt-cells = <1>;
304 };
305 };
306 };
307
308 ocmcram1: ocmcram@40300000 {
309 compatible = "mmio-sram";
310 reg = <0x40300000 0x80000>;
311 ranges = <0x0 0x40300000 0x80000>;
312 #address-cells = <1>;
313 #size-cells = <1>;
314 /*
315 * This is a placeholder for an optional reserved
316 * region for use by secure software. The size
317 * of this region is not known until runtime so it
318 * is set as zero to either be updated to reserve
319 * space or left unchanged to leave all SRAM for use.
320 * On HS parts that that require the reserved region
321 * either the bootloader can update the size to
322 * the required amount or the node can be overridden
323 * from the board dts file for the secure platform.
324 */
325 sram-hs@0 {
326 compatible = "ti,secure-ram";
327 reg = <0x0 0x0>;
328 };
329 };
330
331 /*
332 * NOTE: ocmcram2 and ocmcram3 are not available on all
333 * DRA7xx and AM57xx variants. Confirm availability in
334 * the data manual for the exact part number in use
335 * before enabling these nodes in the board dts file.
336 */
337 ocmcram2: ocmcram@40400000 {
338 status = "disabled";
339 compatible = "mmio-sram";
340 reg = <0x40400000 0x100000>;
341 ranges = <0x0 0x40400000 0x100000>;
342 #address-cells = <1>;
343 #size-cells = <1>;
344 };
345
346 ocmcram3: ocmcram@40500000 {
347 status = "disabled";
348 compatible = "mmio-sram";
349 reg = <0x40500000 0x100000>;
350 ranges = <0x0 0x40500000 0x100000>;
351 #address-cells = <1>;
352 #size-cells = <1>;
353 };
354
355 bandgap: bandgap@4a0021e0 {
356 reg = <0x4a0021e0 0xc
357 0x4a00232c 0xc
358 0x4a002380 0x2c
359 0x4a0023C0 0x3c
360 0x4a002564 0x8
361 0x4a002574 0x50>;
362 compatible = "ti,dra752-bandgap";
363 interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
364 #thermal-sensor-cells = <1>;
365 };
366
367 dsp1_system: dsp_system@40d00000 {
368 compatible = "syscon";
369 reg = <0x40d00000 0x100>;
370 };
371
372 dra7_iodelay_core: padconf@4844a000 {
373 compatible = "ti,dra7-iodelay";
374 reg = <0x4844a000 0x0d1c>;
375 #address-cells = <1>;
376 #size-cells = <0>;
377 #pinctrl-cells = <2>;
378 };
379
380 target-module@43300000 {
381 compatible = "ti,sysc-omap4", "ti,sysc";
382 reg = <0x43300000 0x4>,
383 <0x43300010 0x4>;
384 reg-names = "rev", "sysc";
385 ti,sysc-midle = <SYSC_IDLE_FORCE>,
386 <SYSC_IDLE_NO>,
387 <SYSC_IDLE_SMART>;
388 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
389 <SYSC_IDLE_NO>,
390 <SYSC_IDLE_SMART>;
391 clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPCC_CLKCTRL 0>;
392 clock-names = "fck";
393 #address-cells = <1>;
394 #size-cells = <1>;
395 ranges = <0x0 0x43300000 0x100000>;
396
397 edma: dma@0 {
398 compatible = "ti,edma3-tpcc";
399 reg = <0 0x100000>;
400 reg-names = "edma3_cc";
401 interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
402 <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
403 <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
404 interrupt-names = "edma3_ccint", "edma3_mperr",
405 "edma3_ccerrint";
406 dma-requests = <64>;
407 #dma-cells = <2>;
408
409 ti,tptcs = <&edma_tptc0 7>, <&edma_tptc1 0>;
410
411 /*
412 * memcpy is disabled, can be enabled with:
413 * ti,edma-memcpy-channels = <20 21>;
414 * for example. Note that these channels need to be
415 * masked in the xbar as well.
416 */
417 };
418 };
419
420 target-module@43400000 {
421 compatible = "ti,sysc-omap4", "ti,sysc";
422 reg = <0x43400000 0x4>,
423 <0x43400010 0x4>;
424 reg-names = "rev", "sysc";
425 ti,sysc-midle = <SYSC_IDLE_FORCE>,
426 <SYSC_IDLE_NO>,
427 <SYSC_IDLE_SMART>;
428 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
429 <SYSC_IDLE_NO>,
430 <SYSC_IDLE_SMART>;
431 clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPTC0_CLKCTRL 0>;
432 clock-names = "fck";
433 #address-cells = <1>;
434 #size-cells = <1>;
435 ranges = <0x0 0x43400000 0x100000>;
436
437 edma_tptc0: dma@0 {
438 compatible = "ti,edma3-tptc";
439 reg = <0 0x100000>;
440 interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
441 interrupt-names = "edma3_tcerrint";
442 };
443 };
444
445 target-module@43500000 {
446 compatible = "ti,sysc-omap4", "ti,sysc";
447 reg = <0x43500000 0x4>,
448 <0x43500010 0x4>;
449 reg-names = "rev", "sysc";
450 ti,sysc-midle = <SYSC_IDLE_FORCE>,
451 <SYSC_IDLE_NO>,
452 <SYSC_IDLE_SMART>;
453 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
454 <SYSC_IDLE_NO>,
455 <SYSC_IDLE_SMART>;
456 clocks = <&l3main1_clkctrl DRA7_L3MAIN1_TPTC1_CLKCTRL 0>;
457 clock-names = "fck";
458 #address-cells = <1>;
459 #size-cells = <1>;
460 ranges = <0x0 0x43500000 0x100000>;
461
462 edma_tptc1: dma@0 {
463 compatible = "ti,edma3-tptc";
464 reg = <0 0x100000>;
465 interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
466 interrupt-names = "edma3_tcerrint";
467 };
468 };
469
470 target-module@4e000000 {
471 compatible = "ti,sysc-omap2", "ti,sysc";
472 reg = <0x4e000000 0x4>,
473 <0x4e000010 0x4>;
474 reg-names = "rev", "sysc";
475 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
476 <SYSC_IDLE_NO>,
477 <SYSC_IDLE_SMART>;
478 ranges = <0x0 0x4e000000 0x2000000>;
479 #size-cells = <1>;
480 #address-cells = <1>;
481
482 dmm@0 {
483 compatible = "ti,omap5-dmm";
484 reg = <0 0x800>;
485 interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
486 };
487 };
488
489 ipu1: ipu@58820000 {
490 compatible = "ti,dra7-ipu";
491 reg = <0x58820000 0x10000>;
492 reg-names = "l2ram";
493 iommus = <&mmu_ipu1>;
494 status = "disabled";
495 resets = <&prm_ipu 0>, <&prm_ipu 1>;
496 clocks = <&ipu1_clkctrl DRA7_IPU1_MMU_IPU1_CLKCTRL 0>;
497 firmware-name = "dra7-ipu1-fw.xem4";
498 };
499
500 ipu2: ipu@55020000 {
501 compatible = "ti,dra7-ipu";
502 reg = <0x55020000 0x10000>;
503 reg-names = "l2ram";
504 iommus = <&mmu_ipu2>;
505 status = "disabled";
506 resets = <&prm_core 0>, <&prm_core 1>;
507 clocks = <&ipu2_clkctrl DRA7_IPU2_MMU_IPU2_CLKCTRL 0>;
508 firmware-name = "dra7-ipu2-fw.xem4";
509 };
510
511 dsp1: dsp@40800000 {
512 compatible = "ti,dra7-dsp";
513 reg = <0x40800000 0x48000>,
514 <0x40e00000 0x8000>,
515 <0x40f00000 0x8000>;
516 reg-names = "l2ram", "l1pram", "l1dram";
517 ti,bootreg = <&scm_conf 0x55c 10>;
518 iommus = <&mmu0_dsp1>, <&mmu1_dsp1>;
519 status = "disabled";
520 resets = <&prm_dsp1 0>;
521 clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>;
522 firmware-name = "dra7-dsp1-fw.xe66";
523 };
524
525 target-module@40d01000 {
526 compatible = "ti,sysc-omap2", "ti,sysc";
527 reg = <0x40d01000 0x4>,
528 <0x40d01010 0x4>,
529 <0x40d01014 0x4>;
530 reg-names = "rev", "sysc", "syss";
531 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
532 <SYSC_IDLE_NO>,
533 <SYSC_IDLE_SMART>;
534 ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
535 SYSC_OMAP2_SOFTRESET |
536 SYSC_OMAP2_AUTOIDLE)>;
537 clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>;
538 clock-names = "fck";
539 resets = <&prm_dsp1 1>;
540 reset-names = "rstctrl";
541 ranges = <0x0 0x40d01000 0x1000>;
542 #size-cells = <1>;
543 #address-cells = <1>;
544
545 mmu0_dsp1: mmu@0 {
546 compatible = "ti,dra7-dsp-iommu";
547 reg = <0x0 0x100>;
548 interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
549 #iommu-cells = <0>;
550 ti,syscon-mmuconfig = <&dsp1_system 0x0>;
551 };
552 };
553
554 target-module@40d02000 {
555 compatible = "ti,sysc-omap2", "ti,sysc";
556 reg = <0x40d02000 0x4>,
557 <0x40d02010 0x4>,
558 <0x40d02014 0x4>;
559 reg-names = "rev", "sysc", "syss";
560 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
561 <SYSC_IDLE_NO>,
562 <SYSC_IDLE_SMART>;
563 ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
564 SYSC_OMAP2_SOFTRESET |
565 SYSC_OMAP2_AUTOIDLE)>;
566 clocks = <&dsp1_clkctrl DRA7_DSP1_MMU0_DSP1_CLKCTRL 0>;
567 clock-names = "fck";
568 resets = <&prm_dsp1 1>;
569 reset-names = "rstctrl";
570 ranges = <0x0 0x40d02000 0x1000>;
571 #size-cells = <1>;
572 #address-cells = <1>;
573
574 mmu1_dsp1: mmu@0 {
575 compatible = "ti,dra7-dsp-iommu";
576 reg = <0x0 0x100>;
577 interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
578 #iommu-cells = <0>;
579 ti,syscon-mmuconfig = <&dsp1_system 0x1>;
580 };
581 };
582
583 target-module@58882000 {
584 compatible = "ti,sysc-omap2", "ti,sysc";
585 reg = <0x58882000 0x4>,
586 <0x58882010 0x4>,
587 <0x58882014 0x4>;
588 reg-names = "rev", "sysc", "syss";
589 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
590 <SYSC_IDLE_NO>,
591 <SYSC_IDLE_SMART>;
592 ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
593 SYSC_OMAP2_SOFTRESET |
594 SYSC_OMAP2_AUTOIDLE)>;
595 clocks = <&ipu1_clkctrl DRA7_IPU1_MMU_IPU1_CLKCTRL 0>;
596 clock-names = "fck";
597 resets = <&prm_ipu 2>;
598 reset-names = "rstctrl";
599 #address-cells = <1>;
600 #size-cells = <1>;
601 ranges = <0x0 0x58882000 0x100>;
602
603 mmu_ipu1: mmu@0 {
604 compatible = "ti,dra7-iommu";
605 reg = <0x0 0x100>;
606 interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>;
607 #iommu-cells = <0>;
608 ti,iommu-bus-err-back;
609 };
610 };
611
612 target-module@55082000 {
613 compatible = "ti,sysc-omap2", "ti,sysc";
614 reg = <0x55082000 0x4>,
615 <0x55082010 0x4>,
616 <0x55082014 0x4>;
617 reg-names = "rev", "sysc", "syss";
618 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
619 <SYSC_IDLE_NO>,
620 <SYSC_IDLE_SMART>;
621 ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
622 SYSC_OMAP2_SOFTRESET |
623 SYSC_OMAP2_AUTOIDLE)>;
624 clocks = <&ipu2_clkctrl DRA7_IPU2_MMU_IPU2_CLKCTRL 0>;
625 clock-names = "fck";
626 resets = <&prm_core 2>;
627 reset-names = "rstctrl";
628 #address-cells = <1>;
629 #size-cells = <1>;
630 ranges = <0x0 0x55082000 0x100>;
631
632 mmu_ipu2: mmu@0 {
633 compatible = "ti,dra7-iommu";
634 reg = <0x0 0x100>;
635 interrupts = <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>;
636 #iommu-cells = <0>;
637 ti,iommu-bus-err-back;
638 };
639 };
640
641 abb_mpu: regulator-abb-mpu@4ae07ddc {
642 compatible = "ti,abb-v3";
643 regulator-name = "abb_mpu";
644 #address-cells = <0>;
645 #size-cells = <0>;
646 clocks = <&sys_clkin1>;
647 ti,settling-time = <50>;
648 ti,clock-cycles = <16>;
649
650 reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>,
651 <0x4ae06014 0x4>, <0x4a003b20 0xc>,
652 <0x4ae0c158 0x4>;
653 reg-names = "setup-address", "control-address",
654 "int-address", "efuse-address",
655 "ldo-address";
656 ti,tranxdone-status-mask = <0x80>;
657 /* LDOVBBMPU_FBB_MUX_CTRL */
658 ti,ldovbb-override-mask = <0x400>;
659 /* LDOVBBMPU_FBB_VSET_OUT */
660 ti,ldovbb-vset-mask = <0x1F>;
661
662 /*
663 * NOTE: only FBB mode used but actual vset will
664 * determine final biasing
665 */
666 ti,abb_info = <
667 /*uV ABB efuse rbb_m fbb_m vset_m*/
668 1060000 0 0x0 0 0x02000000 0x01F00000
669 1160000 0 0x4 0 0x02000000 0x01F00000
670 1210000 0 0x8 0 0x02000000 0x01F00000
671 >;
672 };
673
674 abb_ivahd: regulator-abb-ivahd@4ae07e34 {
675 compatible = "ti,abb-v3";
676 regulator-name = "abb_ivahd";
677 #address-cells = <0>;
678 #size-cells = <0>;
679 clocks = <&sys_clkin1>;
680 ti,settling-time = <50>;
681 ti,clock-cycles = <16>;
682
683 reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>,
684 <0x4ae06010 0x4>, <0x4a0025cc 0xc>,
685 <0x4a002470 0x4>;
686 reg-names = "setup-address", "control-address",
687 "int-address", "efuse-address",
688 "ldo-address";
689 ti,tranxdone-status-mask = <0x40000000>;
690 /* LDOVBBIVA_FBB_MUX_CTRL */
691 ti,ldovbb-override-mask = <0x400>;
692 /* LDOVBBIVA_FBB_VSET_OUT */
693 ti,ldovbb-vset-mask = <0x1F>;
694
695 /*
696 * NOTE: only FBB mode used but actual vset will
697 * determine final biasing
698 */
699 ti,abb_info = <
700 /*uV ABB efuse rbb_m fbb_m vset_m*/
701 1055000 0 0x0 0 0x02000000 0x01F00000
702 1150000 0 0x4 0 0x02000000 0x01F00000
703 1250000 0 0x8 0 0x02000000 0x01F00000
704 >;
705 };
706
707 abb_dspeve: regulator-abb-dspeve@4ae07e30 {
708 compatible = "ti,abb-v3";
709 regulator-name = "abb_dspeve";
710 #address-cells = <0>;
711 #size-cells = <0>;
712 clocks = <&sys_clkin1>;
713 ti,settling-time = <50>;
714 ti,clock-cycles = <16>;
715
716 reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>,
717 <0x4ae06010 0x4>, <0x4a0025e0 0xc>,
718 <0x4a00246c 0x4>;
719 reg-names = "setup-address", "control-address",
720 "int-address", "efuse-address",
721 "ldo-address";
722 ti,tranxdone-status-mask = <0x20000000>;
723 /* LDOVBBDSPEVE_FBB_MUX_CTRL */
724 ti,ldovbb-override-mask = <0x400>;
725 /* LDOVBBDSPEVE_FBB_VSET_OUT */
726 ti,ldovbb-vset-mask = <0x1F>;
727
728 /*
729 * NOTE: only FBB mode used but actual vset will
730 * determine final biasing
731 */
732 ti,abb_info = <
733 /*uV ABB efuse rbb_m fbb_m vset_m*/
734 1055000 0 0x0 0 0x02000000 0x01F00000
735 1150000 0 0x4 0 0x02000000 0x01F00000
736 1250000 0 0x8 0 0x02000000 0x01F00000
737 >;
738 };
739
740 abb_gpu: regulator-abb-gpu@4ae07de4 {
741 compatible = "ti,abb-v3";
742 regulator-name = "abb_gpu";
743 #address-cells = <0>;
744 #size-cells = <0>;
745 clocks = <&sys_clkin1>;
746 ti,settling-time = <50>;
747 ti,clock-cycles = <16>;
748
749 reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>,
750 <0x4ae06010 0x4>, <0x4a003b08 0xc>,
751 <0x4ae0c154 0x4>;
752 reg-names = "setup-address", "control-address",
753 "int-address", "efuse-address",
754 "ldo-address";
755 ti,tranxdone-status-mask = <0x10000000>;
756 /* LDOVBBGPU_FBB_MUX_CTRL */
757 ti,ldovbb-override-mask = <0x400>;
758 /* LDOVBBGPU_FBB_VSET_OUT */
759 ti,ldovbb-vset-mask = <0x1F>;
760
761 /*
762 * NOTE: only FBB mode used but actual vset will
763 * determine final biasing
764 */
765 ti,abb_info = <
766 /*uV ABB efuse rbb_m fbb_m vset_m*/
767 1090000 0 0x0 0 0x02000000 0x01F00000
768 1210000 0 0x4 0 0x02000000 0x01F00000
769 1280000 0 0x8 0 0x02000000 0x01F00000
770 >;
771 };
772
773 target-module@4b300000 {
774 compatible = "ti,sysc-omap4", "ti,sysc";
775 reg = <0x4b300000 0x4>,
776 <0x4b300010 0x4>;
777 reg-names = "rev", "sysc";
778 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
779 <SYSC_IDLE_NO>,
780 <SYSC_IDLE_SMART>,
781 <SYSC_IDLE_SMART_WKUP>;
782 clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 0>;
783 clock-names = "fck";
784 #address-cells = <1>;
785 #size-cells = <1>;
786 ranges = <0x0 0x4b300000 0x1000>,
787 <0x5c000000 0x5c000000 0x4000000>;
788
789 qspi: spi@0 {
790 compatible = "ti,dra7xxx-qspi";
791 reg = <0 0x100>,
792 <0x5c000000 0x4000000>;
793 reg-names = "qspi_base", "qspi_mmap";
794 syscon-chipselects = <&scm_conf 0x558>;
795 #address-cells = <1>;
796 #size-cells = <0>;
797 clocks = <&l4per2_clkctrl DRA7_L4PER2_QSPI_CLKCTRL 25>;
798 clock-names = "fck";
799 num-cs = <4>;
800 interrupts = <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>;
801 status = "disabled";
802 };
803 };
804
805 /* OCP2SCP1 */
806 /* IRQ for DWC3_3 and DWC3_4 need IRQ crossbar */
807
808 target-module@50000000 {
809 compatible = "ti,sysc-omap2", "ti,sysc";
810 reg = <0x50000000 4>,
811 <0x50000010 4>,
812 <0x50000014 4>;
813 reg-names = "rev", "sysc", "syss";
814 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
815 <SYSC_IDLE_NO>,
816 <SYSC_IDLE_SMART>;
817 ti,syss-mask = <1>;
818 clocks = <&l3main1_clkctrl DRA7_L3MAIN1_GPMC_CLKCTRL 0>;
819 clock-names = "fck";
820 #address-cells = <1>;
821 #size-cells = <1>;
822 ranges = <0x50000000 0x50000000 0x00001000>, /* regs */
823 <0x00000000 0x00000000 0x40000000>; /* data */
824
825 gpmc: gpmc@50000000 {
826 compatible = "ti,am3352-gpmc";
827 reg = <0x50000000 0x37c>; /* device IO registers */
828 interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
829 dmas = <&edma_xbar 4 0>;
830 dma-names = "rxtx";
831 gpmc,num-cs = <8>;
832 gpmc,num-waitpins = <2>;
833 #address-cells = <2>;
834 #size-cells = <1>;
835 interrupt-controller;
836 #interrupt-cells = <2>;
837 gpio-controller;
838 #gpio-cells = <2>;
839 status = "disabled";
840 };
841 };
842
843 target-module@56000000 {
844 compatible = "ti,sysc-omap4", "ti,sysc";
845 reg = <0x5600fe00 0x4>,
846 <0x5600fe10 0x4>;
847 reg-names = "rev", "sysc";
848 ti,sysc-midle = <SYSC_IDLE_FORCE>,
849 <SYSC_IDLE_NO>,
850 <SYSC_IDLE_SMART>;
851 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
852 <SYSC_IDLE_NO>,
853 <SYSC_IDLE_SMART>,
854 <SYSC_IDLE_SMART_WKUP>;
855 clocks = <&gpu_clkctrl DRA7_GPU_CLKCTRL 0>;
856 clock-names = "fck";
857 #address-cells = <1>;
858 #size-cells = <1>;
859 ranges = <0 0x56000000 0x2000000>;
860
861 gpu@0 {
862 compatible = "ti,am5728-gpu", "img,powervr-sgx544";
863 reg = <0x0 0x10000>; /* 64kB */
864 interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
865 };
866 };
867
868 crossbar_mpu: crossbar@4a002a48 {
869 compatible = "ti,irq-crossbar";
870 reg = <0x4a002a48 0x130>;
871 interrupt-controller;
872 interrupt-parent = <&wakeupgen>;
873 #interrupt-cells = <3>;
874 ti,max-irqs = <160>;
875 ti,max-crossbar-sources = <MAX_SOURCES>;
876 ti,reg-size = <2>;
877 ti,irqs-reserved = <0 1 2 3 5 6 131 132>;
878 ti,irqs-skip = <10 133 139 140>;
879 ti,irqs-safe-map = <0>;
880 };
881
882 target-module@58000000 {
883 compatible = "ti,sysc-omap2", "ti,sysc";
884 reg = <0x58000000 4>,
885 <0x58000014 4>;
886 reg-names = "rev", "syss";
887 ti,syss-mask = <1>;
888 clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 0>,
889 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>,
890 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 10>,
891 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 11>;
892 clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk";
893 #address-cells = <1>;
894 #size-cells = <1>;
895 ranges = <0 0x58000000 0x800000>;
896
897 dss: dss@0 {
898 compatible = "ti,dra7-dss";
899 /* 'reg' defined in dra72x.dtsi and dra74x.dtsi */
900 /* 'clocks' defined in dra72x.dtsi and dra74x.dtsi */
901 status = "disabled";
902 /* CTRL_CORE_DSS_PLL_CONTROL */
903 syscon-pll-ctrl = <&scm_conf 0x538>;
904 #address-cells = <1>;
905 #size-cells = <1>;
906 ranges = <0 0 0x800000>;
907
908 target-module@1000 {
909 compatible = "ti,sysc-omap2", "ti,sysc";
910 reg = <0x1000 0x4>,
911 <0x1010 0x4>,
912 <0x1014 0x4>;
913 reg-names = "rev", "sysc", "syss";
914 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
915 <SYSC_IDLE_NO>,
916 <SYSC_IDLE_SMART>;
917 ti,sysc-midle = <SYSC_IDLE_FORCE>,
918 <SYSC_IDLE_NO>,
919 <SYSC_IDLE_SMART>;
920 ti,sysc-mask = <(SYSC_OMAP2_CLOCKACTIVITY |
921 SYSC_OMAP2_ENAWAKEUP |
922 SYSC_OMAP2_SOFTRESET |
923 SYSC_OMAP2_AUTOIDLE)>;
924 ti,syss-mask = <1>;
925 clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>;
926 clock-names = "fck";
927 #address-cells = <1>;
928 #size-cells = <1>;
929 ranges = <0 0x1000 0x1000>;
930
931 dispc@0 {
932 compatible = "ti,dra7-dispc";
933 reg = <0 0x1000>;
934 interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
935 clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>;
936 clock-names = "fck";
937 /* CTRL_CORE_SMA_SW_1 */
938 syscon-pol = <&scm_conf 0x534>;
939 };
940 };
941
942 target-module@40000 {
943 compatible = "ti,sysc-omap4", "ti,sysc";
944 reg = <0x40000 0x4>,
945 <0x40010 0x4>;
946 reg-names = "rev", "sysc";
947 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
948 <SYSC_IDLE_NO>,
949 <SYSC_IDLE_SMART>,
950 <SYSC_IDLE_SMART_WKUP>;
951 ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>;
952 clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>,
953 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>;
954 clock-names = "fck", "dss_clk";
955 #address-cells = <1>;
956 #size-cells = <1>;
957 ranges = <0 0x40000 0x40000>;
958
959 hdmi: encoder@0 {
960 compatible = "ti,dra7-hdmi";
961 reg = <0 0x200>,
962 <0x200 0x80>,
963 <0x300 0x80>,
964 <0x20000 0x19000>;
965 reg-names = "wp", "pll", "phy", "core";
966 interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
967 status = "disabled";
968 clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>,
969 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 10>;
970 clock-names = "fck", "sys_clk";
971 dmas = <&sdma_xbar 76>;
972 dma-names = "audio_tx";
973 };
974 };
975 };
976 };
977
978 target-module@59000000 {
979 compatible = "ti,sysc-omap4", "ti,sysc";
980 reg = <0x59000020 0x4>;
981 reg-names = "rev";
982 clocks = <&dss_clkctrl DRA7_DSS_BB2D_CLKCTRL 0>;
983 clock-names = "fck";
984 #address-cells = <1>;
985 #size-cells = <1>;
986 ranges = <0x0 0x59000000 0x1000>;
987
988 bb2d: gpu@0 {
989 compatible = "vivante,gc";
990 reg = <0x0 0x700>;
991 interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
992 clocks = <&dss_clkctrl DRA7_DSS_BB2D_CLKCTRL 0>;
993 clock-names = "core";
994 };
995 };
996
997 aes1_target: target-module@4b500000 {
998 compatible = "ti,sysc-omap2", "ti,sysc";
999 reg = <0x4b500080 0x4>,
1000 <0x4b500084 0x4>,
1001 <0x4b500088 0x4>;
1002 reg-names = "rev", "sysc", "syss";
1003 ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
1004 SYSC_OMAP2_AUTOIDLE)>;
1005 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
1006 <SYSC_IDLE_NO>,
1007 <SYSC_IDLE_SMART>,
1008 <SYSC_IDLE_SMART_WKUP>;
1009 ti,syss-mask = <1>;
1010 /* Domains (P, C): per_pwrdm, l4sec_clkdm */
1011 clocks = <&l4sec_clkctrl DRA7_L4SEC_AES1_CLKCTRL 0>;
1012 clock-names = "fck";
1013 #address-cells = <1>;
1014 #size-cells = <1>;
1015 ranges = <0x0 0x4b500000 0x1000>;
1016
1017 aes1: aes@0 {
1018 compatible = "ti,omap4-aes";
1019 reg = <0 0xa0>;
1020 interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
1021 dmas = <&edma_xbar 111 0>, <&edma_xbar 110 0>;
1022 dma-names = "tx", "rx";
1023 clocks = <&l3_iclk_div>;
1024 clock-names = "fck";
1025 };
1026 };
1027
1028 aes2_target: target-module@4b700000 {
1029 compatible = "ti,sysc-omap2", "ti,sysc";
1030 reg = <0x4b700080 0x4>,
1031 <0x4b700084 0x4>,
1032 <0x4b700088 0x4>;
1033 reg-names = "rev", "sysc", "syss";
1034 ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
1035 SYSC_OMAP2_AUTOIDLE)>;
1036 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
1037 <SYSC_IDLE_NO>,
1038 <SYSC_IDLE_SMART>,
1039 <SYSC_IDLE_SMART_WKUP>;
1040 ti,syss-mask = <1>;
1041 /* Domains (P, C): per_pwrdm, l4sec_clkdm */
1042 clocks = <&l4sec_clkctrl DRA7_L4SEC_AES2_CLKCTRL 0>;
1043 clock-names = "fck";
1044 #address-cells = <1>;
1045 #size-cells = <1>;
1046 ranges = <0x0 0x4b700000 0x1000>;
1047
1048 aes2: aes@0 {
1049 compatible = "ti,omap4-aes";
1050 reg = <0 0xa0>;
1051 interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
1052 dmas = <&edma_xbar 114 0>, <&edma_xbar 113 0>;
1053 dma-names = "tx", "rx";
1054 clocks = <&l3_iclk_div>;
1055 clock-names = "fck";
1056 };
1057 };
1058
1059 sham1_target: target-module@4b101000 {
1060 compatible = "ti,sysc-omap3-sham", "ti,sysc";
1061 reg = <0x4b101100 0x4>,
1062 <0x4b101110 0x4>,
1063 <0x4b101114 0x4>;
1064 reg-names = "rev", "sysc", "syss";
1065 ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
1066 SYSC_OMAP2_AUTOIDLE)>;
1067 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
1068 <SYSC_IDLE_NO>,
1069 <SYSC_IDLE_SMART>;
1070 ti,syss-mask = <1>;
1071 /* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
1072 clocks = <&l4sec_clkctrl DRA7_L4SEC_SHAM_CLKCTRL 0>;
1073 clock-names = "fck";
1074 #address-cells = <1>;
1075 #size-cells = <1>;
1076 ranges = <0x0 0x4b101000 0x1000>;
1077
1078 sham1: sham@0 {
1079 compatible = "ti,omap5-sham";
1080 reg = <0 0x300>;
1081 interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
1082 dmas = <&edma_xbar 119 0>;
1083 dma-names = "rx";
1084 clocks = <&l3_iclk_div>;
1085 clock-names = "fck";
1086 };
1087 };
1088
1089 sham2_target: target-module@42701000 {
1090 compatible = "ti,sysc-omap3-sham", "ti,sysc";
1091 reg = <0x42701100 0x4>,
1092 <0x42701110 0x4>,
1093 <0x42701114 0x4>;
1094 reg-names = "rev", "sysc", "syss";
1095 ti,sysc-mask = <(SYSC_OMAP2_SOFTRESET |
1096 SYSC_OMAP2_AUTOIDLE)>;
1097 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
1098 <SYSC_IDLE_NO>,
1099 <SYSC_IDLE_SMART>;
1100 ti,syss-mask = <1>;
1101 /* Domains (P, C): l4per_pwrdm, l4sec_clkdm */
1102 clocks = <&l4sec_clkctrl DRA7_L4SEC_SHAM2_CLKCTRL 0>;
1103 clock-names = "fck";
1104 #address-cells = <1>;
1105 #size-cells = <1>;
1106 ranges = <0x0 0x42701000 0x1000>;
1107
1108 sham2: sham@0 {
1109 compatible = "ti,omap5-sham";
1110 reg = <0 0x300>;
1111 interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
1112 dmas = <&edma_xbar 165 0>;
1113 dma-names = "rx";
1114 clocks = <&l3_iclk_div>;
1115 clock-names = "fck";
1116 };
1117 };
1118
1119 iva_hd_target: target-module@5a000000 {
1120 compatible = "ti,sysc-omap4", "ti,sysc";
1121 reg = <0x5a05a400 0x4>,
1122 <0x5a05a410 0x4>;
1123 reg-names = "rev", "sysc";
1124 ti,sysc-midle = <SYSC_IDLE_FORCE>,
1125 <SYSC_IDLE_NO>,
1126 <SYSC_IDLE_SMART>;
1127 ti,sysc-sidle = <SYSC_IDLE_FORCE>,
1128 <SYSC_IDLE_NO>,
1129 <SYSC_IDLE_SMART>;
1130 power-domains = <&prm_iva>;
1131 resets = <&prm_iva 2>;
1132 reset-names = "rstctrl";
1133 clocks = <&iva_clkctrl DRA7_IVA_CLKCTRL 0>;
1134 clock-names = "fck";
1135 #address-cells = <1>;
1136 #size-cells = <1>;
1137 ranges = <0x5a000000 0x5a000000 0x1000000>,
1138 <0x5b000000 0x5b000000 0x1000000>;
1139
1140 iva {
1141 compatible = "ti,ivahd";
1142 };
1143 };
1144
1145 opp_supply_mpu: opp-supply@4a003b20 {
1146 compatible = "ti,omap5-opp-supply";
1147 reg = <0x4a003b20 0xc>;
1148 ti,efuse-settings = <
1149 /* uV offset */
1150 1060000 0x0
1151 1160000 0x4
1152 1210000 0x8
1153 >;
1154 ti,absolute-max-voltage-uv = <1500000>;
1155 };
1156
1157 };
1158
1159 thermal_zones: thermal-zones {
1160 #include "omap4-cpu-thermal.dtsi"
1161 #include "omap5-gpu-thermal.dtsi"
1162 #include "omap5-core-thermal.dtsi"
1163 #include "dra7-dspeve-thermal.dtsi"
1164 #include "dra7-iva-thermal.dtsi"
1165 };
1166
1167 };
1168
1169 &cpu_thermal {
1170 polling-delay = <500>; /* milliseconds */
1171 coefficients = <0 2000>;
1172 };
1173
1174 &gpu_thermal {
1175 coefficients = <0 2000>;
1176 };
1177
1178 &core_thermal {
1179 coefficients = <0 2000>;
1180 };
1181
1182 &dspeve_thermal {
1183 coefficients = <0 2000>;
1184 };
1185
1186 &iva_thermal {
1187 coefficients = <0 2000>;
1188 };
1189
1190 &cpu_crit {
1191 temperature = <120000>; /* milli Celsius */
1192 };
1193
1194 &core_crit {
1195 temperature = <120000>; /* milli Celsius */
1196 };
1197
1198 &gpu_crit {
1199 temperature = <120000>; /* milli Celsius */
1200 };
1201
1202 &dspeve_crit {
1203 temperature = <120000>; /* milli Celsius */
1204 };
1205
1206 &iva_crit {
1207 temperature = <120000>; /* milli Celsius */
1208 };
1209
1210 #include "dra7-l4.dtsi"
1211 #include "dra7xx-clocks.dtsi"
1212
1213 &prm {
1214 prm_mpu: prm@300 {
1215 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1216 reg = <0x300 0x100>;
1217 #power-domain-cells = <0>;
1218 };
1219
1220 prm_dsp1: prm@400 {
1221 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1222 reg = <0x400 0x100>;
1223 #reset-cells = <1>;
1224 #power-domain-cells = <0>;
1225 };
1226
1227 prm_ipu: prm@500 {
1228 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1229 reg = <0x500 0x100>;
1230 #reset-cells = <1>;
1231 #power-domain-cells = <0>;
1232 };
1233
1234 prm_coreaon: prm@628 {
1235 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1236 reg = <0x628 0xd8>;
1237 #power-domain-cells = <0>;
1238 };
1239
1240 prm_core: prm@700 {
1241 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1242 reg = <0x700 0x100>;
1243 #reset-cells = <1>;
1244 #power-domain-cells = <0>;
1245 };
1246
1247 prm_iva: prm@f00 {
1248 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1249 reg = <0xf00 0x100>;
1250 #reset-cells = <1>;
1251 #power-domain-cells = <0>;
1252 };
1253
1254 prm_cam: prm@1000 {
1255 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1256 reg = <0x1000 0x100>;
1257 #power-domain-cells = <0>;
1258 };
1259
1260 prm_dss: prm@1100 {
1261 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1262 reg = <0x1100 0x100>;
1263 #power-domain-cells = <0>;
1264 };
1265
1266 prm_gpu: prm@1200 {
1267 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1268 reg = <0x1200 0x100>;
1269 #power-domain-cells = <0>;
1270 };
1271
1272 prm_l3init: prm@1300 {
1273 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1274 reg = <0x1300 0x100>;
1275 #reset-cells = <1>;
1276 #power-domain-cells = <0>;
1277 };
1278
1279 prm_l4per: prm@1400 {
1280 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1281 reg = <0x1400 0x100>;
1282 #power-domain-cells = <0>;
1283 };
1284
1285 prm_custefuse: prm@1600 {
1286 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1287 reg = <0x1600 0x100>;
1288 #power-domain-cells = <0>;
1289 };
1290
1291 prm_wkupaon: prm@1724 {
1292 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1293 reg = <0x1724 0x100>;
1294 #power-domain-cells = <0>;
1295 };
1296
1297 prm_dsp2: prm@1b00 {
1298 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1299 reg = <0x1b00 0x40>;
1300 #reset-cells = <1>;
1301 #power-domain-cells = <0>;
1302 };
1303
1304 prm_eve1: prm@1b40 {
1305 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1306 reg = <0x1b40 0x40>;
1307 #power-domain-cells = <0>;
1308 };
1309
1310 prm_eve2: prm@1b80 {
1311 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1312 reg = <0x1b80 0x40>;
1313 #power-domain-cells = <0>;
1314 };
1315
1316 prm_eve3: prm@1bc0 {
1317 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1318 reg = <0x1bc0 0x40>;
1319 #power-domain-cells = <0>;
1320 };
1321
1322 prm_eve4: prm@1c00 {
1323 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1324 reg = <0x1c00 0x60>;
1325 #power-domain-cells = <0>;
1326 };
1327
1328 prm_rtc: prm@1c60 {
1329 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1330 reg = <0x1c60 0x20>;
1331 #power-domain-cells = <0>;
1332 };
1333
1334 prm_vpe: prm@1c80 {
1335 compatible = "ti,dra7-prm-inst", "ti,omap-prm-inst";
1336 reg = <0x1c80 0x80>;
1337 #power-domain-cells = <0>;
1338 };
1339 };
1340
1341 /* Preferred always-on timer for clockevent */
1342 &timer1_target {
1343 ti,no-reset-on-init;
1344 ti,no-idle;
1345 timer@0 {
1346 assigned-clocks = <&wkupaon_clkctrl DRA7_WKUPAON_TIMER1_CLKCTRL 24>;
1347 assigned-clock-parents = <&sys_32k_ck>;
1348 };
1349 };
1350
1351 /* Local timers, see ARM architected timer wrap erratum i940 */
1352 &timer15_target {
1353 ti,no-reset-on-init;
1354 ti,no-idle;
1355 timer@0 {
1356 assigned-clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER15_CLKCTRL 24>;
1357 assigned-clock-parents = <&timer_sys_clk_div>;
1358 };
1359 };
1360
1361 &timer16_target {
1362 ti,no-reset-on-init;
1363 ti,no-idle;
1364 timer@0 {
1365 assigned-clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER16_CLKCTRL 24>;
1366 assigned-clock-parents = <&timer_sys_clk_div>;
1367 };
1368 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.