1 /* SPDX-License-Identifier: GPL-2.0 */ 2 #ifndef _ASM_POWERPC_KEYLARGO_H 3 #define _ASM_POWERPC_KEYLARGO_H 4 #ifdef __KERNEL__ 5 /* 6 * keylargo.h: definitions for using the "KeyLargo" I/O controller chip. 7 * 8 */ 9 10 /* "Pangea" chipset has keylargo device-id 0x25 while core99 11 * has device-id 0x22. The rev. of the pangea one is 0, so we 12 * fake an artificial rev. in keylargo_rev by oring 0x100 13 */ 14 #define KL_PANGEA_REV 0x100 15 16 /* offset from base for feature control registers */ 17 #define KEYLARGO_MBCR 0x34 /* KL Only, Media bay control/status */ 18 #define KEYLARGO_FCR0 0x38 19 #define KEYLARGO_FCR1 0x3c 20 #define KEYLARGO_FCR2 0x40 21 #define KEYLARGO_FCR3 0x44 22 #define KEYLARGO_FCR4 0x48 23 #define KEYLARGO_FCR5 0x4c /* Pangea only */ 24 25 /* K2 additional FCRs */ 26 #define K2_FCR6 0x34 27 #define K2_FCR7 0x30 28 #define K2_FCR8 0x2c 29 #define K2_FCR9 0x28 30 #define K2_FCR10 0x24 31 32 /* GPIO registers */ 33 #define KEYLARGO_GPIO_LEVELS0 0x50 34 #define KEYLARGO_GPIO_LEVELS1 0x54 35 #define KEYLARGO_GPIO_EXTINT_0 0x58 36 #define KEYLARGO_GPIO_EXTINT_CNT 18 37 #define KEYLARGO_GPIO_0 0x6A 38 #define KEYLARGO_GPIO_CNT 17 39 #define KEYLARGO_GPIO_EXTINT_DUAL_EDGE 0x80 40 #define KEYLARGO_GPIO_OUTPUT_ENABLE 0x04 41 #define KEYLARGO_GPIO_OUTOUT_DATA 0x01 42 #define KEYLARGO_GPIO_INPUT_DATA 0x02 43 44 /* K2 does only extint GPIOs and does 51 of them */ 45 #define K2_GPIO_EXTINT_0 0x58 46 #define K2_GPIO_EXTINT_CNT 51 47 48 /* Specific GPIO regs */ 49 50 #define KL_GPIO_MODEM_RESET (KEYLARGO_GPIO_0+0x03) 51 #define KL_GPIO_MODEM_POWER (KEYLARGO_GPIO_0+0x02) /* Pangea */ 52 53 #define KL_GPIO_SOUND_POWER (KEYLARGO_GPIO_0+0x05) 54 55 /* Hrm... this one is only to be used on Pismo. It seems to also 56 * control the timebase enable on other machines. Still to be 57 * experimented... --BenH. 58 */ 59 #define KL_GPIO_FW_CABLE_POWER (KEYLARGO_GPIO_0+0x09) 60 #define KL_GPIO_TB_ENABLE (KEYLARGO_GPIO_0+0x09) 61 62 #define KL_GPIO_ETH_PHY_RESET (KEYLARGO_GPIO_0+0x10) 63 64 #define KL_GPIO_EXTINT_CPU1 (KEYLARGO_GPIO_0+0x0a) 65 #define KL_GPIO_EXTINT_CPU1_ASSERT 0x04 66 #define KL_GPIO_EXTINT_CPU1_RELEASE 0x38 67 68 #define KL_GPIO_RESET_CPU0 (KEYLARGO_GPIO_EXTINT_0+0x03) 69 #define KL_GPIO_RESET_CPU1 (KEYLARGO_GPIO_EXTINT_0+0x04) 70 #define KL_GPIO_RESET_CPU2 (KEYLARGO_GPIO_EXTINT_0+0x0f) 71 #define KL_GPIO_RESET_CPU3 (KEYLARGO_GPIO_EXTINT_0+0x10) 72 73 #define KL_GPIO_PMU_MESSAGE_IRQ (KEYLARGO_GPIO_EXTINT_0+0x09) 74 #define KL_GPIO_PMU_MESSAGE_BIT KEYLARGO_GPIO_INPUT_DATA 75 76 #define KL_GPIO_MEDIABAY_IRQ (KEYLARGO_GPIO_EXTINT_0+0x0e) 77 78 #define KL_GPIO_AIRPORT_0 (KEYLARGO_GPIO_EXTINT_0+0x0a) 79 #define KL_GPIO_AIRPORT_1 (KEYLARGO_GPIO_EXTINT_0+0x0d) 80 #define KL_GPIO_AIRPORT_2 (KEYLARGO_GPIO_0+0x0d) 81 #define KL_GPIO_AIRPORT_3 (KEYLARGO_GPIO_0+0x0e) 82 #define KL_GPIO_AIRPORT_4 (KEYLARGO_GPIO_0+0x0f) 83 84 /* 85 * Bits in feature control register. Those bits different for K2 are 86 * listed separately 87 */ 88 #define KL_MBCR_MB0_PCI_ENABLE 0x00000800 /* exist ? */ 89 #define KL_MBCR_MB0_IDE_ENABLE 0x00001000 90 #define KL_MBCR_MB0_FLOPPY_ENABLE 0x00002000 /* exist ? */ 91 #define KL_MBCR_MB0_SOUND_ENABLE 0x00004000 /* hrm... */ 92 #define KL_MBCR_MB0_DEV_MASK 0x00007800 93 #define KL_MBCR_MB0_DEV_POWER 0x00000400 94 #define KL_MBCR_MB0_DEV_RESET 0x00000200 95 #define KL_MBCR_MB0_ENABLE 0x00000100 96 #define KL_MBCR_MB1_PCI_ENABLE 0x08000000 /* exist ? */ 97 #define KL_MBCR_MB1_IDE_ENABLE 0x10000000 98 #define KL_MBCR_MB1_FLOPPY_ENABLE 0x20000000 /* exist ? */ 99 #define KL_MBCR_MB1_SOUND_ENABLE 0x40000000 /* hrm... */ 100 #define KL_MBCR_MB1_DEV_MASK 0x78000000 101 #define KL_MBCR_MB1_DEV_POWER 0x04000000 102 #define KL_MBCR_MB1_DEV_RESET 0x02000000 103 #define KL_MBCR_MB1_ENABLE 0x01000000 104 105 #define KL0_SCC_B_INTF_ENABLE 0x00000001 /* (KL Only) */ 106 #define KL0_SCC_A_INTF_ENABLE 0x00000002 107 #define KL0_SCC_SLOWPCLK 0x00000004 108 #define KL0_SCC_RESET 0x00000008 109 #define KL0_SCCA_ENABLE 0x00000010 110 #define KL0_SCCB_ENABLE 0x00000020 111 #define KL0_SCC_CELL_ENABLE 0x00000040 112 #define KL0_IRDA_HIGH_BAND 0x00000100 /* (KL Only) */ 113 #define KL0_IRDA_SOURCE2_SEL 0x00000200 /* (KL Only) */ 114 #define KL0_IRDA_SOURCE1_SEL 0x00000400 /* (KL Only) */ 115 #define KL0_PG_USB0_PMI_ENABLE 0x00000400 /* (Pangea/Intrepid Only) */ 116 #define KL0_IRDA_RESET 0x00000800 /* (KL Only) */ 117 #define KL0_PG_USB0_REF_SUSPEND_SEL 0x00000800 /* (Pangea/Intrepid Only) */ 118 #define KL0_IRDA_DEFAULT1 0x00001000 /* (KL Only) */ 119 #define KL0_PG_USB0_REF_SUSPEND 0x00001000 /* (Pangea/Intrepid Only) */ 120 #define KL0_IRDA_DEFAULT0 0x00002000 /* (KL Only) */ 121 #define KL0_PG_USB0_PAD_SUSPEND 0x00002000 /* (Pangea/Intrepid Only) */ 122 #define KL0_IRDA_FAST_CONNECT 0x00004000 /* (KL Only) */ 123 #define KL0_PG_USB1_PMI_ENABLE 0x00004000 /* (Pangea/Intrepid Only) */ 124 #define KL0_IRDA_ENABLE 0x00008000 /* (KL Only) */ 125 #define KL0_PG_USB1_REF_SUSPEND_SEL 0x00008000 /* (Pangea/Intrepid Only) */ 126 #define KL0_IRDA_CLK32_ENABLE 0x00010000 /* (KL Only) */ 127 #define KL0_PG_USB1_REF_SUSPEND 0x00010000 /* (Pangea/Intrepid Only) */ 128 #define KL0_IRDA_CLK19_ENABLE 0x00020000 /* (KL Only) */ 129 #define KL0_PG_USB1_PAD_SUSPEND 0x00020000 /* (Pangea/Intrepid Only) */ 130 #define KL0_USB0_PAD_SUSPEND0 0x00040000 131 #define KL0_USB0_PAD_SUSPEND1 0x00080000 132 #define KL0_USB0_CELL_ENABLE 0x00100000 133 #define KL0_USB1_PAD_SUSPEND0 0x00400000 134 #define KL0_USB1_PAD_SUSPEND1 0x00800000 135 #define KL0_USB1_CELL_ENABLE 0x01000000 136 #define KL0_USB_REF_SUSPEND 0x10000000 /* (KL Only) */ 137 138 #define KL0_SERIAL_ENABLE (KL0_SCC_B_INTF_ENABLE | \ 139 KL0_SCC_SLOWPCLK | \ 140 KL0_SCC_CELL_ENABLE | KL0_SCCA_ENABLE) 141 142 #define KL1_USB2_PMI_ENABLE 0x00000001 /* Intrepid only */ 143 #define KL1_AUDIO_SEL_22MCLK 0x00000002 /* KL/Pangea only */ 144 #define KL1_USB2_REF_SUSPEND_SEL 0x00000002 /* Intrepid only */ 145 #define KL1_USB2_REF_SUSPEND 0x00000004 /* Intrepid only */ 146 #define KL1_AUDIO_CLK_ENABLE_BIT 0x00000008 /* KL/Pangea only */ 147 #define KL1_USB2_PAD_SUSPEND_SEL 0x00000008 /* Intrepid only */ 148 #define KL1_USB2_PAD_SUSPEND0 0x00000010 /* Intrepid only */ 149 #define KL1_AUDIO_CLK_OUT_ENABLE 0x00000020 /* KL/Pangea only */ 150 #define KL1_USB2_PAD_SUSPEND1 0x00000020 /* Intrepid only */ 151 #define KL1_AUDIO_CELL_ENABLE 0x00000040 /* KL/Pangea only */ 152 #define KL1_USB2_CELL_ENABLE 0x00000040 /* Intrepid only */ 153 #define KL1_AUDIO_CHOOSE 0x00000080 /* KL/Pangea only */ 154 #define KL1_I2S0_CHOOSE 0x00000200 /* KL Only */ 155 #define KL1_I2S0_CELL_ENABLE 0x00000400 156 #define KL1_I2S0_CLK_ENABLE_BIT 0x00001000 157 #define KL1_I2S0_ENABLE 0x00002000 158 #define KL1_I2S1_CELL_ENABLE 0x00020000 159 #define KL1_I2S1_CLK_ENABLE_BIT 0x00080000 160 #define KL1_I2S1_ENABLE 0x00100000 161 #define KL1_EIDE0_ENABLE 0x00800000 /* KL/Intrepid Only */ 162 #define KL1_EIDE0_RESET_N 0x01000000 /* KL/Intrepid Only */ 163 #define KL1_EIDE1_ENABLE 0x04000000 /* KL Only */ 164 #define KL1_EIDE1_RESET_N 0x08000000 /* KL Only */ 165 #define KL1_UIDE_ENABLE 0x20000000 /* KL/Pangea Only */ 166 #define KL1_UIDE_RESET_N 0x40000000 /* KL/Pangea Only */ 167 168 #define KL2_IOBUS_ENABLE 0x00000002 169 #define KL2_SLEEP_STATE_BIT 0x00000100 /* KL Only */ 170 #define KL2_PG_STOP_ALL_CLOCKS 0x00000100 /* Pangea Only */ 171 #define KL2_MPIC_ENABLE 0x00020000 172 #define KL2_CARDSLOT_RESET 0x00040000 /* Pangea/Intrepid Only */ 173 #define KL2_ALT_DATA_OUT 0x02000000 /* KL Only ??? */ 174 #define KL2_MEM_IS_BIG 0x04000000 175 #define KL2_CARDSEL_16 0x08000000 176 177 #define KL3_SHUTDOWN_PLL_TOTAL 0x00000001 /* KL/Pangea only */ 178 #define KL3_SHUTDOWN_PLLKW6 0x00000002 /* KL/Pangea only */ 179 #define KL3_IT_SHUTDOWN_PLL3 0x00000002 /* Intrepid only */ 180 #define KL3_SHUTDOWN_PLLKW4 0x00000004 /* KL/Pangea only */ 181 #define KL3_IT_SHUTDOWN_PLL2 0x00000004 /* Intrepid only */ 182 #define KL3_SHUTDOWN_PLLKW35 0x00000008 /* KL/Pangea only */ 183 #define KL3_IT_SHUTDOWN_PLL1 0x00000008 /* Intrepid only */ 184 #define KL3_SHUTDOWN_PLLKW12 0x00000010 /* KL Only */ 185 #define KL3_IT_ENABLE_PLL3_SHUTDOWN 0x00000010 /* Intrepid only */ 186 #define KL3_PLL_RESET 0x00000020 /* KL/Pangea only */ 187 #define KL3_IT_ENABLE_PLL2_SHUTDOWN 0x00000020 /* Intrepid only */ 188 #define KL3_IT_ENABLE_PLL1_SHUTDOWN 0x00000010 /* Intrepid only */ 189 #define KL3_SHUTDOWN_PLL2X 0x00000080 /* KL Only */ 190 #define KL3_CLK66_ENABLE 0x00000100 /* KL Only */ 191 #define KL3_CLK49_ENABLE 0x00000200 192 #define KL3_CLK45_ENABLE 0x00000400 193 #define KL3_CLK31_ENABLE 0x00000800 /* KL/Pangea only */ 194 #define KL3_TIMER_CLK18_ENABLE 0x00001000 195 #define KL3_I2S1_CLK18_ENABLE 0x00002000 196 #define KL3_I2S0_CLK18_ENABLE 0x00004000 197 #define KL3_VIA_CLK16_ENABLE 0x00008000 /* KL/Pangea only */ 198 #define KL3_IT_VIA_CLK32_ENABLE 0x00008000 /* Intrepid only */ 199 #define KL3_STOPPING33_ENABLED 0x00080000 /* KL Only */ 200 #define KL3_PG_PLL_ENABLE_TEST 0x00080000 /* Pangea Only */ 201 202 /* Intrepid USB bus 2, port 0,1 */ 203 #define KL3_IT_PORT_WAKEUP_ENABLE(p) (0x00080000 << ((p)<<3)) 204 #define KL3_IT_PORT_RESUME_WAKE_EN(p) (0x00040000 << ((p)<<3)) 205 #define KL3_IT_PORT_CONNECT_WAKE_EN(p) (0x00020000 << ((p)<<3)) 206 #define KL3_IT_PORT_DISCONNECT_WAKE_EN(p) (0x00010000 << ((p)<<3)) 207 #define KL3_IT_PORT_RESUME_STAT(p) (0x00300000 << ((p)<<3)) 208 #define KL3_IT_PORT_CONNECT_STAT(p) (0x00200000 << ((p)<<3)) 209 #define KL3_IT_PORT_DISCONNECT_STAT(p) (0x00100000 << ((p)<<3)) 210 211 /* Port 0,1 : bus 0, port 2,3 : bus 1 */ 212 #define KL4_PORT_WAKEUP_ENABLE(p) (0x00000008 << ((p)<<3)) 213 #define KL4_PORT_RESUME_WAKE_EN(p) (0x00000004 << ((p)<<3)) 214 #define KL4_PORT_CONNECT_WAKE_EN(p) (0x00000002 << ((p)<<3)) 215 #define KL4_PORT_DISCONNECT_WAKE_EN(p) (0x00000001 << ((p)<<3)) 216 #define KL4_PORT_RESUME_STAT(p) (0x00000040 << ((p)<<3)) 217 #define KL4_PORT_CONNECT_STAT(p) (0x00000020 << ((p)<<3)) 218 #define KL4_PORT_DISCONNECT_STAT(p) (0x00000010 << ((p)<<3)) 219 220 /* Pangea and Intrepid only */ 221 #define KL5_VIA_USE_CLK31 0000000001 /* Pangea Only */ 222 #define KL5_SCC_USE_CLK31 0x00000002 /* Pangea Only */ 223 #define KL5_PWM_CLK32_EN 0x00000004 224 #define KL5_CLK3_68_EN 0x00000010 225 #define KL5_CLK32_EN 0x00000020 226 227 228 /* K2 definitions */ 229 #define K2_FCR0_USB0_SWRESET 0x00200000 230 #define K2_FCR0_USB1_SWRESET 0x02000000 231 #define K2_FCR0_RING_PME_DISABLE 0x08000000 232 233 #define K2_FCR1_PCI1_BUS_RESET_N 0x00000010 234 #define K2_FCR1_PCI1_SLEEP_RESET_EN 0x00000020 235 #define K2_FCR1_I2S0_CELL_ENABLE 0x00000400 236 #define K2_FCR1_I2S0_RESET 0x00000800 237 #define K2_FCR1_I2S0_CLK_ENABLE_BIT 0x00001000 238 #define K2_FCR1_I2S0_ENABLE 0x00002000 239 #define K2_FCR1_PCI1_CLK_ENABLE 0x00004000 240 #define K2_FCR1_FW_CLK_ENABLE 0x00008000 241 #define K2_FCR1_FW_RESET_N 0x00010000 242 #define K2_FCR1_I2S1_CELL_ENABLE 0x00020000 243 #define K2_FCR1_I2S1_CLK_ENABLE_BIT 0x00080000 244 #define K2_FCR1_I2S1_ENABLE 0x00100000 245 #define K2_FCR1_GMAC_CLK_ENABLE 0x00400000 246 #define K2_FCR1_GMAC_POWER_DOWN 0x00800000 247 #define K2_FCR1_GMAC_RESET_N 0x01000000 248 #define K2_FCR1_SATA_CLK_ENABLE 0x02000000 249 #define K2_FCR1_SATA_POWER_DOWN 0x04000000 250 #define K2_FCR1_SATA_RESET_N 0x08000000 251 #define K2_FCR1_UATA_CLK_ENABLE 0x10000000 252 #define K2_FCR1_UATA_RESET_N 0x40000000 253 #define K2_FCR1_UATA_CHOOSE_CLK66 0x80000000 254 255 /* Shasta definitions */ 256 #define SH_FCR1_I2S2_CELL_ENABLE 0x00000010 257 #define SH_FCR1_I2S2_CLK_ENABLE_BIT 0x00000040 258 #define SH_FCR1_I2S2_ENABLE 0x00000080 259 #define SH_FCR3_I2S2_CLK18_ENABLE 0x00008000 260 261 #endif /* __KERNEL__ */ 262 #endif /* _ASM_POWERPC_KEYLARGO_H */ 263
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.