1 // SPDX-License-Identifier: GPL-2.0-or-later
2 /*
3 * Copyright 2010-2011, 2013 Freescale Semiconductor, Inc.
4 *
5 * Author: Michael Johnston <michael.johnston@freescale.com>
6 *
7 * Description:
8 * TWR-P102x Board Setup
9 */
10
11 #include <linux/kernel.h>
12 #include <linux/init.h>
13 #include <linux/errno.h>
14 #include <linux/fsl/guts.h>
15 #include <linux/pci.h>
16 #include <linux/of.h>
17 #include <linux/of_address.h>
18
19 #include <asm/pci-bridge.h>
20 #include <asm/udbg.h>
21 #include <asm/mpic.h>
22 #include <soc/fsl/qe/qe.h>
23
24 #include <sysdev/fsl_soc.h>
25 #include <sysdev/fsl_pci.h>
26 #include "smp.h"
27
28 #include "mpc85xx.h"
29
30 static void __init twr_p1025_pic_init(void)
31 {
32 struct mpic *mpic;
33
34 mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN |
35 MPIC_SINGLE_DEST_CPU,
36 0, 256, " OpenPIC ");
37
38 BUG_ON(mpic == NULL);
39 mpic_init(mpic);
40 }
41
42 /* ************************************************************************
43 *
44 * Setup the architecture
45 *
46 */
47 static void __init twr_p1025_setup_arch(void)
48 {
49 if (ppc_md.progress)
50 ppc_md.progress("twr_p1025_setup_arch()", 0);
51
52 mpc85xx_smp_init();
53
54 fsl_pci_assign_primary();
55
56 #ifdef CONFIG_QUICC_ENGINE
57 mpc85xx_qe_par_io_init();
58
59 #if IS_ENABLED(CONFIG_UCC_GETH) || IS_ENABLED(CONFIG_SERIAL_QE)
60 if (machine_is(twr_p1025)) {
61 struct ccsr_guts __iomem *guts;
62 struct device_node *np;
63
64 np = of_find_compatible_node(NULL, NULL, "fsl,p1021-guts");
65 if (np) {
66 guts = of_iomap(np, 0);
67 if (!guts)
68 pr_err("twr_p1025: could not map global utilities register\n");
69 else {
70 /* P1025 has pins muxed for QE and other functions. To
71 * enable QE UEC mode, we need to set bit QE0 for UCC1
72 * in Eth mode, QE0 and QE3 for UCC5 in Eth mode, QE9
73 * and QE12 for QE MII management signals in PMUXCR
74 * register.
75 * Set QE mux bits in PMUXCR */
76 setbits32(&guts->pmuxcr, MPC85xx_PMUXCR_QE(0) |
77 MPC85xx_PMUXCR_QE(3) |
78 MPC85xx_PMUXCR_QE(9) |
79 MPC85xx_PMUXCR_QE(12));
80 iounmap(guts);
81
82 #if IS_ENABLED(CONFIG_SERIAL_QE)
83 /* On P1025TWR board, the UCC7 acted as UART port.
84 * However, The UCC7's CTS pin is low level in default,
85 * it will impact the transmission in full duplex
86 * communication. So disable the Flow control pin PA18.
87 * The UCC7 UART just can use RXD and TXD pins.
88 */
89 par_io_config_pin(0, 18, 0, 0, 0, 0);
90 #endif
91 /* Drive PB29 to CPLD low - CPLD will then change
92 * muxing from LBC to QE */
93 par_io_config_pin(1, 29, 1, 0, 0, 0);
94 par_io_data_set(1, 29, 0);
95 }
96 of_node_put(np);
97 }
98 }
99 #endif
100 #endif /* CONFIG_QUICC_ENGINE */
101
102 pr_info("TWR-P1025 board from Freescale Semiconductor\n");
103 }
104
105 machine_arch_initcall(twr_p1025, mpc85xx_common_publish_devices);
106
107 define_machine(twr_p1025) {
108 .name = "TWR-P1025",
109 .compatible = "fsl,TWR-P1025",
110 .setup_arch = twr_p1025_setup_arch,
111 .init_IRQ = twr_p1025_pic_init,
112 #ifdef CONFIG_PCI
113 .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
114 #endif
115 .get_irq = mpic_get_irq,
116 .progress = udbg_progress,
117 };
118
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.