1 /* SPDX-License-Identifier: GPL-2.0-only */
2 /*
3 * Hardware-specific External Interface I/O core definitions
4 * for the BCM47xx family of SiliconBackplane-based chips.
5 *
6 * The External Interface core supports a total of three external chip selects
7 * supporting external interfaces. One of the external chip selects is
8 * used for Flash, one is used for PCMCIA, and the other may be
9 * programmed to support either a synchronous interface or an
10 * asynchronous interface. The asynchronous interface can be used to
11 * support external devices such as UARTs and the BCM2019 Bluetooth
12 * baseband processor.
13 * The external interface core also contains 2 on-chip 16550 UARTs, clock
14 * frequency control, a watchdog interrupt timer, and a GPIO interface.
15 *
16 * Copyright 2005, Broadcom Corporation
17 * Copyright 2006, Michael Buesch
18 */
19 #ifndef LINUX_SSB_EXTIFCORE_H_
20 #define LINUX_SSB_EXTIFCORE_H_
21
22 /* external interface address space */
23 #define SSB_EXTIF_PCMCIA_MEMBASE(x) (x)
24 #define SSB_EXTIF_PCMCIA_IOBASE(x) ((x) + 0x100000)
25 #define SSB_EXTIF_PCMCIA_CFGBASE(x) ((x) + 0x200000)
26 #define SSB_EXTIF_CFGIF_BASE(x) ((x) + 0x800000)
27 #define SSB_EXTIF_FLASH_BASE(x) ((x) + 0xc00000)
28
29 #define SSB_EXTIF_NR_GPIOOUT 5
30 /* GPIO NOTE:
31 * The multiple instances of output and output enable registers
32 * are present to allow driver software for multiple cores to control
33 * gpio outputs without needing to share a single register pair.
34 * Use the following helper macro to get a register offset value.
35 */
36 #define SSB_EXTIF_GPIO_OUT(index) ({ \
37 BUILD_BUG_ON(index >= SSB_EXTIF_NR_GPIOOUT); \
38 SSB_EXTIF_GPIO_OUT_BASE + ((index) * 8); \
39 })
40 #define SSB_EXTIF_GPIO_OUTEN(index) ({ \
41 BUILD_BUG_ON(index >= SSB_EXTIF_NR_GPIOOUT); \
42 SSB_EXTIF_GPIO_OUTEN_BASE + ((index) * 8); \
43 })
44
45 /** EXTIF core registers **/
46
47 #define SSB_EXTIF_CTL 0x0000
48 #define SSB_EXTIF_CTL_UARTEN (1 << 0) /* UART enable */
49 #define SSB_EXTIF_EXTSTAT 0x0004
50 #define SSB_EXTIF_EXTSTAT_EMODE (1 << 0) /* Endian mode (ro) */
51 #define SSB_EXTIF_EXTSTAT_EIRQPIN (1 << 1) /* External interrupt pin (ro) */
52 #define SSB_EXTIF_EXTSTAT_GPIOIRQPIN (1 << 2) /* GPIO interrupt pin (ro) */
53 #define SSB_EXTIF_PCMCIA_CFG 0x0010
54 #define SSB_EXTIF_PCMCIA_MEMWAIT 0x0014
55 #define SSB_EXTIF_PCMCIA_ATTRWAIT 0x0018
56 #define SSB_EXTIF_PCMCIA_IOWAIT 0x001C
57 #define SSB_EXTIF_PROG_CFG 0x0020
58 #define SSB_EXTIF_PROG_WAITCNT 0x0024
59 #define SSB_EXTIF_FLASH_CFG 0x0028
60 #define SSB_EXTIF_FLASH_WAITCNT 0x002C
61 #define SSB_EXTIF_WATCHDOG 0x0040
62 #define SSB_EXTIF_CLOCK_N 0x0044
63 #define SSB_EXTIF_CLOCK_SB 0x0048
64 #define SSB_EXTIF_CLOCK_PCI 0x004C
65 #define SSB_EXTIF_CLOCK_MII 0x0050
66 #define SSB_EXTIF_GPIO_IN 0x0060
67 #define SSB_EXTIF_GPIO_OUT_BASE 0x0064
68 #define SSB_EXTIF_GPIO_OUTEN_BASE 0x0068
69 #define SSB_EXTIF_EJTAG_OUTEN 0x0090
70 #define SSB_EXTIF_GPIO_INTPOL 0x0094
71 #define SSB_EXTIF_GPIO_INTMASK 0x0098
72 #define SSB_EXTIF_UART_DATA 0x0300
73 #define SSB_EXTIF_UART_TIMER 0x0310
74 #define SSB_EXTIF_UART_FCR 0x0320
75 #define SSB_EXTIF_UART_LCR 0x0330
76 #define SSB_EXTIF_UART_MCR 0x0340
77 #define SSB_EXTIF_UART_LSR 0x0350
78 #define SSB_EXTIF_UART_MSR 0x0360
79 #define SSB_EXTIF_UART_SCRATCH 0x0370
80
81
82
83
84 /* pcmcia/prog/flash_config */
85 #define SSB_EXTCFG_EN (1 << 0) /* enable */
86 #define SSB_EXTCFG_MODE 0xE /* mode */
87 #define SSB_EXTCFG_MODE_SHIFT 1
88 #define SSB_EXTCFG_MODE_FLASH 0x0 /* flash/asynchronous mode */
89 #define SSB_EXTCFG_MODE_SYNC 0x2 /* synchronous mode */
90 #define SSB_EXTCFG_MODE_PCMCIA 0x4 /* pcmcia mode */
91 #define SSB_EXTCFG_DS16 (1 << 4) /* destsize: 0=8bit, 1=16bit */
92 #define SSB_EXTCFG_BSWAP (1 << 5) /* byteswap */
93 #define SSB_EXTCFG_CLKDIV 0xC0 /* clock divider */
94 #define SSB_EXTCFG_CLKDIV_SHIFT 6
95 #define SSB_EXTCFG_CLKDIV_2 0x0 /* backplane/2 */
96 #define SSB_EXTCFG_CLKDIV_3 0x40 /* backplane/3 */
97 #define SSB_EXTCFG_CLKDIV_4 0x80 /* backplane/4 */
98 #define SSB_EXTCFG_CLKEN (1 << 8) /* clock enable */
99 #define SSB_EXTCFG_STROBE (1 << 9) /* size/bytestrobe (synch only) */
100
101 /* pcmcia_memwait */
102 #define SSB_PCMCIA_MEMW_0 0x0000003F /* waitcount0 */
103 #define SSB_PCMCIA_MEMW_1 0x00001F00 /* waitcount1 */
104 #define SSB_PCMCIA_MEMW_1_SHIFT 8
105 #define SSB_PCMCIA_MEMW_2 0x001F0000 /* waitcount2 */
106 #define SSB_PCMCIA_MEMW_2_SHIFT 16
107 #define SSB_PCMCIA_MEMW_3 0x1F000000 /* waitcount3 */
108 #define SSB_PCMCIA_MEMW_3_SHIFT 24
109
110 /* pcmcia_attrwait */
111 #define SSB_PCMCIA_ATTW_0 0x0000003F /* waitcount0 */
112 #define SSB_PCMCIA_ATTW_1 0x00001F00 /* waitcount1 */
113 #define SSB_PCMCIA_ATTW_1_SHIFT 8
114 #define SSB_PCMCIA_ATTW_2 0x001F0000 /* waitcount2 */
115 #define SSB_PCMCIA_ATTW_2_SHIFT 16
116 #define SSB_PCMCIA_ATTW_3 0x1F000000 /* waitcount3 */
117 #define SSB_PCMCIA_ATTW_3_SHIFT 24
118
119 /* pcmcia_iowait */
120 #define SSB_PCMCIA_IOW_0 0x0000003F /* waitcount0 */
121 #define SSB_PCMCIA_IOW_1 0x00001F00 /* waitcount1 */
122 #define SSB_PCMCIA_IOW_1_SHIFT 8
123 #define SSB_PCMCIA_IOW_2 0x001F0000 /* waitcount2 */
124 #define SSB_PCMCIA_IOW_2_SHIFT 16
125 #define SSB_PCMCIA_IOW_3 0x1F000000 /* waitcount3 */
126 #define SSB_PCMCIA_IOW_3_SHIFT 24
127
128 /* prog_waitcount */
129 #define SSB_PROG_WCNT_0 0x0000001F /* waitcount0 */
130 #define SSB_PROG_WCNT_1 0x00001F00 /* waitcount1 */
131 #define SSB_PROG_WCNT_1_SHIFT 8
132 #define SSB_PROG_WCNT_2 0x001F0000 /* waitcount2 */
133 #define SSB_PROG_WCNT_2_SHIFT 16
134 #define SSB_PROG_WCNT_3 0x1F000000 /* waitcount3 */
135 #define SSB_PROG_WCNT_3_SHIFT 24
136
137 #define SSB_PROG_W0 0x0000000C
138 #define SSB_PROG_W1 0x00000A00
139 #define SSB_PROG_W2 0x00020000
140 #define SSB_PROG_W3 0x01000000
141
142 /* flash_waitcount */
143 #define SSB_FLASH_WCNT_0 0x0000001F /* waitcount0 */
144 #define SSB_FLASH_WCNT_1 0x00001F00 /* waitcount1 */
145 #define SSB_FLASH_WCNT_1_SHIFT 8
146 #define SSB_FLASH_WCNT_2 0x001F0000 /* waitcount2 */
147 #define SSB_FLASH_WCNT_2_SHIFT 16
148 #define SSB_FLASH_WCNT_3 0x1F000000 /* waitcount3 */
149 #define SSB_FLASH_WCNT_3_SHIFT 24
150
151 /* watchdog */
152 #define SSB_EXTIF_WATCHDOG_CLK 48000000 /* Hz */
153
154 #define SSB_EXTIF_WATCHDOG_MAX_TIMER ((1 << 28) - 1)
155 #define SSB_EXTIF_WATCHDOG_MAX_TIMER_MS (SSB_EXTIF_WATCHDOG_MAX_TIMER \
156 / (SSB_EXTIF_WATCHDOG_CLK / 1000))
157
158
159 #ifdef CONFIG_SSB_DRIVER_EXTIF
160
161 struct ssb_extif {
162 struct ssb_device *dev;
163 spinlock_t gpio_lock;
164 };
165
166 static inline bool ssb_extif_available(struct ssb_extif *extif)
167 {
168 return (extif->dev != NULL);
169 }
170
171 extern void ssb_extif_get_clockcontrol(struct ssb_extif *extif,
172 u32 *plltype, u32 *n, u32 *m);
173
174 extern void ssb_extif_timing_init(struct ssb_extif *extif,
175 unsigned long ns);
176
177 extern u32 ssb_extif_watchdog_timer_set(struct ssb_extif *extif, u32 ticks);
178
179 /* Extif GPIO pin access */
180 u32 ssb_extif_gpio_in(struct ssb_extif *extif, u32 mask);
181 u32 ssb_extif_gpio_out(struct ssb_extif *extif, u32 mask, u32 value);
182 u32 ssb_extif_gpio_outen(struct ssb_extif *extif, u32 mask, u32 value);
183 u32 ssb_extif_gpio_polarity(struct ssb_extif *extif, u32 mask, u32 value);
184 u32 ssb_extif_gpio_intmask(struct ssb_extif *extif, u32 mask, u32 value);
185
186 #ifdef CONFIG_SSB_SERIAL
187 extern int ssb_extif_serial_init(struct ssb_extif *extif,
188 struct ssb_serial_port *ports);
189 #endif /* CONFIG_SSB_SERIAL */
190
191
192 #else /* CONFIG_SSB_DRIVER_EXTIF */
193 /* extif disabled */
194
195 struct ssb_extif {
196 };
197
198 static inline bool ssb_extif_available(struct ssb_extif *extif)
199 {
200 return false;
201 }
202
203 static inline
204 void ssb_extif_get_clockcontrol(struct ssb_extif *extif,
205 u32 *plltype, u32 *n, u32 *m)
206 {
207 }
208
209 static inline
210 void ssb_extif_timing_init(struct ssb_extif *extif, unsigned long ns)
211 {
212 }
213
214 static inline
215 u32 ssb_extif_watchdog_timer_set(struct ssb_extif *extif, u32 ticks)
216 {
217 return 0;
218 }
219
220 static inline u32 ssb_extif_gpio_in(struct ssb_extif *extif, u32 mask)
221 {
222 return 0;
223 }
224
225 static inline u32 ssb_extif_gpio_out(struct ssb_extif *extif, u32 mask,
226 u32 value)
227 {
228 return 0;
229 }
230
231 static inline u32 ssb_extif_gpio_outen(struct ssb_extif *extif, u32 mask,
232 u32 value)
233 {
234 return 0;
235 }
236
237 static inline u32 ssb_extif_gpio_polarity(struct ssb_extif *extif, u32 mask,
238 u32 value)
239 {
240 return 0;
241 }
242
243 static inline u32 ssb_extif_gpio_intmask(struct ssb_extif *extif, u32 mask,
244 u32 value)
245 {
246 return 0;
247 }
248
249 #ifdef CONFIG_SSB_SERIAL
250 static inline int ssb_extif_serial_init(struct ssb_extif *extif,
251 struct ssb_serial_port *ports)
252 {
253 return 0;
254 }
255 #endif /* CONFIG_SSB_SERIAL */
256
257 #endif /* CONFIG_SSB_DRIVER_EXTIF */
258 #endif /* LINUX_SSB_EXTIFCORE_H_ */
259
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.