1 // SPDX-License-Identifier: GPL-2.0
2 #include "bcm283x.dtsi"
3
4 #include <dt-bindings/interrupt-controller/arm-gic.h>
5 #include <dt-bindings/soc/bcm2835-pm.h>
6
7 / {
8 compatible = "brcm,bcm2711";
9
10 #address-cells = <2>;
11 #size-cells = <1>;
12
13 interrupt-parent = <&gicv2>;
14
15 vc4: gpu {
16 compatible = "brcm,bcm2711-vc5";
17 status = "disabled";
18 };
19
20 clk_27MHz: clk-27M {
21 #clock-cells = <0>;
22 compatible = "fixed-clock";
23 clock-frequency = <27000000>;
24 clock-output-names = "27MHz-clock";
25 };
26
27 clk_108MHz: clk-108M {
28 #clock-cells = <0>;
29 compatible = "fixed-clock";
30 clock-frequency = <108000000>;
31 clock-output-names = "108MHz-clock";
32 };
33
34 soc {
35 /*
36 * Defined ranges:
37 * Common BCM283x peripherals
38 * BCM2711-specific peripherals
39 * ARM-local peripherals
40 */
41 ranges = <0x7e000000 0x0 0xfe000000 0x01800000>,
42 <0x7c000000 0x0 0xfc000000 0x02000000>,
43 <0x40000000 0x0 0xff800000 0x00800000>;
44 /* Emulate a contiguous 30-bit address range for DMA */
45 dma-ranges = <0xc0000000 0x0 0x00000000 0x40000000>;
46
47 /*
48 * This node is the provider for the enable-method for
49 * bringing up secondary cores.
50 */
51 local_intc: interrupt-controller@40000000 {
52 compatible = "brcm,bcm2836-l1-intc";
53 reg = <0x40000000 0x100>;
54 };
55
56 gicv2: interrupt-controller@40041000 {
57 interrupt-controller;
58 #interrupt-cells = <3>;
59 compatible = "arm,gic-400";
60 reg = <0x40041000 0x1000>,
61 <0x40042000 0x2000>,
62 <0x40044000 0x2000>,
63 <0x40046000 0x2000>;
64 interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
65 IRQ_TYPE_LEVEL_HIGH)>;
66 };
67
68 avs_monitor: avs-monitor@7d5d2000 {
69 compatible = "brcm,bcm2711-avs-monitor",
70 "syscon", "simple-mfd";
71 reg = <0x7d5d2000 0xf00>;
72
73 thermal: thermal {
74 compatible = "brcm,bcm2711-thermal";
75 #thermal-sensor-cells = <0>;
76 };
77 };
78
79 dma: dma-controller@7e007000 {
80 compatible = "brcm,bcm2835-dma";
81 reg = <0x7e007000 0xb00>;
82 interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
83 <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
84 <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
85 <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
86 <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
87 <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
88 <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
89 /* DMA lite 7 - 10 */
90 <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
91 <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
92 <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
93 <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
94 interrupt-names = "dma0",
95 "dma1",
96 "dma2",
97 "dma3",
98 "dma4",
99 "dma5",
100 "dma6",
101 "dma7",
102 "dma8",
103 "dma9",
104 "dma10";
105 #dma-cells = <1>;
106 brcm,dma-channel-mask = <0x07f5>;
107 };
108
109 pm: watchdog@7e100000 {
110 compatible = "brcm,bcm2711-pm", "brcm,bcm2835-pm-wdt";
111 #power-domain-cells = <1>;
112 #reset-cells = <1>;
113 reg = <0x7e100000 0x114>,
114 <0x7e00a000 0x24>,
115 <0x7ec11000 0x20>;
116 reg-names = "pm", "asb", "rpivid_asb";
117 clocks = <&clocks BCM2835_CLOCK_V3D>,
118 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
119 <&clocks BCM2835_CLOCK_H264>,
120 <&clocks BCM2835_CLOCK_ISP>;
121 clock-names = "v3d", "peri_image", "h264", "isp";
122 system-power-controller;
123 };
124
125 rng@7e104000 {
126 compatible = "brcm,bcm2711-rng200";
127 reg = <0x7e104000 0x28>;
128 };
129
130 uart2: serial@7e201400 {
131 compatible = "arm,pl011", "arm,primecell";
132 reg = <0x7e201400 0x200>;
133 interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
134 clocks = <&clocks BCM2835_CLOCK_UART>,
135 <&clocks BCM2835_CLOCK_VPU>;
136 clock-names = "uartclk", "apb_pclk";
137 arm,primecell-periphid = <0x00241011>;
138 status = "disabled";
139 };
140
141 uart3: serial@7e201600 {
142 compatible = "arm,pl011", "arm,primecell";
143 reg = <0x7e201600 0x200>;
144 interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
145 clocks = <&clocks BCM2835_CLOCK_UART>,
146 <&clocks BCM2835_CLOCK_VPU>;
147 clock-names = "uartclk", "apb_pclk";
148 arm,primecell-periphid = <0x00241011>;
149 status = "disabled";
150 };
151
152 uart4: serial@7e201800 {
153 compatible = "arm,pl011", "arm,primecell";
154 reg = <0x7e201800 0x200>;
155 interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
156 clocks = <&clocks BCM2835_CLOCK_UART>,
157 <&clocks BCM2835_CLOCK_VPU>;
158 clock-names = "uartclk", "apb_pclk";
159 arm,primecell-periphid = <0x00241011>;
160 status = "disabled";
161 };
162
163 uart5: serial@7e201a00 {
164 compatible = "arm,pl011", "arm,primecell";
165 reg = <0x7e201a00 0x200>;
166 interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
167 clocks = <&clocks BCM2835_CLOCK_UART>,
168 <&clocks BCM2835_CLOCK_VPU>;
169 clock-names = "uartclk", "apb_pclk";
170 arm,primecell-periphid = <0x00241011>;
171 status = "disabled";
172 };
173
174 spi3: spi@7e204600 {
175 compatible = "brcm,bcm2835-spi";
176 reg = <0x7e204600 0x0200>;
177 interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
178 clocks = <&clocks BCM2835_CLOCK_VPU>;
179 #address-cells = <1>;
180 #size-cells = <0>;
181 status = "disabled";
182 };
183
184 spi4: spi@7e204800 {
185 compatible = "brcm,bcm2835-spi";
186 reg = <0x7e204800 0x0200>;
187 interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
188 clocks = <&clocks BCM2835_CLOCK_VPU>;
189 #address-cells = <1>;
190 #size-cells = <0>;
191 status = "disabled";
192 };
193
194 spi5: spi@7e204a00 {
195 compatible = "brcm,bcm2835-spi";
196 reg = <0x7e204a00 0x0200>;
197 interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
198 clocks = <&clocks BCM2835_CLOCK_VPU>;
199 #address-cells = <1>;
200 #size-cells = <0>;
201 status = "disabled";
202 };
203
204 spi6: spi@7e204c00 {
205 compatible = "brcm,bcm2835-spi";
206 reg = <0x7e204c00 0x0200>;
207 interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
208 clocks = <&clocks BCM2835_CLOCK_VPU>;
209 #address-cells = <1>;
210 #size-cells = <0>;
211 status = "disabled";
212 };
213
214 i2c3: i2c@7e205600 {
215 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
216 reg = <0x7e205600 0x200>;
217 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
218 clocks = <&clocks BCM2835_CLOCK_VPU>;
219 #address-cells = <1>;
220 #size-cells = <0>;
221 status = "disabled";
222 };
223
224 i2c4: i2c@7e205800 {
225 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
226 reg = <0x7e205800 0x200>;
227 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
228 clocks = <&clocks BCM2835_CLOCK_VPU>;
229 #address-cells = <1>;
230 #size-cells = <0>;
231 status = "disabled";
232 };
233
234 i2c5: i2c@7e205a00 {
235 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
236 reg = <0x7e205a00 0x200>;
237 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
238 clocks = <&clocks BCM2835_CLOCK_VPU>;
239 #address-cells = <1>;
240 #size-cells = <0>;
241 status = "disabled";
242 };
243
244 i2c6: i2c@7e205c00 {
245 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
246 reg = <0x7e205c00 0x200>;
247 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
248 clocks = <&clocks BCM2835_CLOCK_VPU>;
249 #address-cells = <1>;
250 #size-cells = <0>;
251 status = "disabled";
252 };
253
254 pixelvalve0: pixelvalve@7e206000 {
255 compatible = "brcm,bcm2711-pixelvalve0";
256 reg = <0x7e206000 0x100>;
257 interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
258 status = "disabled";
259 };
260
261 pixelvalve1: pixelvalve@7e207000 {
262 compatible = "brcm,bcm2711-pixelvalve1";
263 reg = <0x7e207000 0x100>;
264 interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
265 status = "disabled";
266 };
267
268 pixelvalve2: pixelvalve@7e20a000 {
269 compatible = "brcm,bcm2711-pixelvalve2";
270 reg = <0x7e20a000 0x100>;
271 interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
272 status = "disabled";
273 };
274
275 pwm1: pwm@7e20c800 {
276 compatible = "brcm,bcm2835-pwm";
277 reg = <0x7e20c800 0x28>;
278 clocks = <&clocks BCM2835_CLOCK_PWM>;
279 assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
280 assigned-clock-rates = <10000000>;
281 #pwm-cells = <3>;
282 status = "disabled";
283 };
284
285 pixelvalve4: pixelvalve@7e216000 {
286 compatible = "brcm,bcm2711-pixelvalve4";
287 reg = <0x7e216000 0x100>;
288 interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
289 status = "disabled";
290 };
291
292 hvs: hvs@7e400000 {
293 compatible = "brcm,bcm2711-hvs";
294 reg = <0x7e400000 0x8000>;
295 interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
296 };
297
298 pixelvalve3: pixelvalve@7ec12000 {
299 compatible = "brcm,bcm2711-pixelvalve3";
300 reg = <0x7ec12000 0x100>;
301 interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
302 status = "disabled";
303 };
304
305 vec: vec@7ec13000 {
306 compatible = "brcm,bcm2711-vec";
307 reg = <0x7ec13000 0x1000>;
308 clocks = <&clocks BCM2835_CLOCK_VEC>;
309 interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
310 status = "disabled";
311 };
312
313 dvp: clock@7ef00000 {
314 compatible = "brcm,brcm2711-dvp";
315 reg = <0x7ef00000 0x10>;
316 clocks = <&clk_108MHz>;
317 #clock-cells = <1>;
318 #reset-cells = <1>;
319 };
320
321 aon_intr: interrupt-controller@7ef00100 {
322 compatible = "brcm,bcm2711-l2-intc", "brcm,l2-intc";
323 reg = <0x7ef00100 0x30>;
324 interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
325 interrupt-controller;
326 #interrupt-cells = <1>;
327 };
328
329 hdmi0: hdmi@7ef00700 {
330 compatible = "brcm,bcm2711-hdmi0";
331 reg = <0x7ef00700 0x300>,
332 <0x7ef00300 0x200>,
333 <0x7ef00f00 0x80>,
334 <0x7ef00f80 0x80>,
335 <0x7ef01b00 0x200>,
336 <0x7ef01f00 0x400>,
337 <0x7ef00200 0x80>,
338 <0x7ef04300 0x100>,
339 <0x7ef20000 0x100>;
340 reg-names = "hdmi",
341 "dvp",
342 "phy",
343 "rm",
344 "packet",
345 "metadata",
346 "csc",
347 "cec",
348 "hd";
349 clock-names = "hdmi", "bvb", "audio", "cec";
350 resets = <&dvp 0>;
351 interrupt-parent = <&aon_intr>;
352 interrupts = <0>, <1>, <2>,
353 <3>, <4>, <5>;
354 interrupt-names = "cec-tx", "cec-rx", "cec-low",
355 "wakeup", "hpd-connected", "hpd-removed";
356 ddc = <&ddc0>;
357 dmas = <&dma 10>;
358 dma-names = "audio-rx";
359 status = "disabled";
360 };
361
362 ddc0: i2c@7ef04500 {
363 compatible = "brcm,bcm2711-hdmi-i2c";
364 reg = <0x7ef04500 0x100>, <0x7ef00b00 0x300>;
365 reg-names = "bsc", "auto-i2c";
366 clock-frequency = <97500>;
367 status = "disabled";
368 };
369
370 hdmi1: hdmi@7ef05700 {
371 compatible = "brcm,bcm2711-hdmi1";
372 reg = <0x7ef05700 0x300>,
373 <0x7ef05300 0x200>,
374 <0x7ef05f00 0x80>,
375 <0x7ef05f80 0x80>,
376 <0x7ef06b00 0x200>,
377 <0x7ef06f00 0x400>,
378 <0x7ef00280 0x80>,
379 <0x7ef09300 0x100>,
380 <0x7ef20000 0x100>;
381 reg-names = "hdmi",
382 "dvp",
383 "phy",
384 "rm",
385 "packet",
386 "metadata",
387 "csc",
388 "cec",
389 "hd";
390 ddc = <&ddc1>;
391 clock-names = "hdmi", "bvb", "audio", "cec";
392 resets = <&dvp 1>;
393 interrupt-parent = <&aon_intr>;
394 interrupts = <8>, <7>, <6>,
395 <9>, <10>, <11>;
396 interrupt-names = "cec-tx", "cec-rx", "cec-low",
397 "wakeup", "hpd-connected", "hpd-removed";
398 dmas = <&dma 17>;
399 dma-names = "audio-rx";
400 status = "disabled";
401 };
402
403 ddc1: i2c@7ef09500 {
404 compatible = "brcm,bcm2711-hdmi-i2c";
405 reg = <0x7ef09500 0x100>, <0x7ef05b00 0x300>;
406 reg-names = "bsc", "auto-i2c";
407 clock-frequency = <97500>;
408 status = "disabled";
409 };
410 };
411
412 /*
413 * emmc2 has different DMA constraints based on SoC revisions. It was
414 * moved into its own bus, so as for RPi4's firmware to update them.
415 * The firmware will find whether the emmc2bus alias is defined, and if
416 * so, it'll edit the dma-ranges property below accordingly.
417 */
418 emmc2bus: emmc2bus {
419 compatible = "simple-bus";
420 #address-cells = <2>;
421 #size-cells = <1>;
422
423 ranges = <0x0 0x7e000000 0x0 0xfe000000 0x01800000>;
424 dma-ranges = <0x0 0xc0000000 0x0 0x00000000 0x40000000>;
425
426 emmc2: mmc@7e340000 {
427 compatible = "brcm,bcm2711-emmc2";
428 reg = <0x0 0x7e340000 0x100>;
429 interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
430 clocks = <&clocks BCM2711_CLOCK_EMMC2>;
431 status = "disabled";
432 };
433 };
434
435 pmu {
436 compatible = "arm,cortex-a72-pmu";
437 interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
438 <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
439 <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
440 <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
441 interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
442 };
443
444 timer {
445 compatible = "arm,armv8-timer";
446 interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) |
447 IRQ_TYPE_LEVEL_LOW)>,
448 <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) |
449 IRQ_TYPE_LEVEL_LOW)>,
450 <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) |
451 IRQ_TYPE_LEVEL_LOW)>,
452 <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) |
453 IRQ_TYPE_LEVEL_LOW)>;
454 /* This only applies to the ARMv7 stub */
455 arm,cpu-registers-not-fw-configured;
456 };
457
458 cpus: cpus {
459 #address-cells = <1>;
460 #size-cells = <0>;
461 enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
462
463 /* Source for d/i-cache-line-size and d/i-cache-sets
464 * https://developer.arm.com/documentation/100095/0003
465 * /Level-1-Memory-System/About-the-L1-memory-system?lang=en
466 * Source for d/i-cache-size
467 * https://www.raspberrypi.com/documentation/computers
468 * /processors.html#bcm2711
469 */
470 cpu0: cpu@0 {
471 device_type = "cpu";
472 compatible = "arm,cortex-a72";
473 reg = <0>;
474 enable-method = "spin-table";
475 cpu-release-addr = <0x0 0x000000d8>;
476 d-cache-size = <0x8000>;
477 d-cache-line-size = <64>;
478 d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
479 i-cache-size = <0xc000>;
480 i-cache-line-size = <64>;
481 i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
482 next-level-cache = <&l2>;
483 };
484
485 cpu1: cpu@1 {
486 device_type = "cpu";
487 compatible = "arm,cortex-a72";
488 reg = <1>;
489 enable-method = "spin-table";
490 cpu-release-addr = <0x0 0x000000e0>;
491 d-cache-size = <0x8000>;
492 d-cache-line-size = <64>;
493 d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
494 i-cache-size = <0xc000>;
495 i-cache-line-size = <64>;
496 i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
497 next-level-cache = <&l2>;
498 };
499
500 cpu2: cpu@2 {
501 device_type = "cpu";
502 compatible = "arm,cortex-a72";
503 reg = <2>;
504 enable-method = "spin-table";
505 cpu-release-addr = <0x0 0x000000e8>;
506 d-cache-size = <0x8000>;
507 d-cache-line-size = <64>;
508 d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
509 i-cache-size = <0xc000>;
510 i-cache-line-size = <64>;
511 i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
512 next-level-cache = <&l2>;
513 };
514
515 cpu3: cpu@3 {
516 device_type = "cpu";
517 compatible = "arm,cortex-a72";
518 reg = <3>;
519 enable-method = "spin-table";
520 cpu-release-addr = <0x0 0x000000f0>;
521 d-cache-size = <0x8000>;
522 d-cache-line-size = <64>;
523 d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
524 i-cache-size = <0xc000>;
525 i-cache-line-size = <64>;
526 i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
527 next-level-cache = <&l2>;
528 };
529
530 /* Source for d/i-cache-line-size and d/i-cache-sets
531 * https://developer.arm.com/documentation/100095/0003
532 * /Level-2-Memory-System/About-the-L2-memory-system?lang=en
533 * Source for d/i-cache-size
534 * https://www.raspberrypi.com/documentation/computers
535 * /processors.html#bcm2711
536 */
537 l2: l2-cache0 {
538 compatible = "cache";
539 cache-unified;
540 cache-size = <0x100000>;
541 cache-line-size = <64>;
542 cache-sets = <1024>; // 1MiB(size)/64(line-size)=16384ways/16-way set
543 cache-level = <2>;
544 };
545 };
546
547 scb {
548 compatible = "simple-bus";
549 #address-cells = <2>;
550 #size-cells = <1>;
551
552 ranges = <0x0 0x7c000000 0x0 0xfc000000 0x03800000>,
553 <0x6 0x00000000 0x6 0x00000000 0x40000000>;
554
555 pcie0: pcie@7d500000 {
556 compatible = "brcm,bcm2711-pcie";
557 reg = <0x0 0x7d500000 0x9310>;
558 device_type = "pci";
559 #address-cells = <3>;
560 #interrupt-cells = <1>;
561 #size-cells = <2>;
562 interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
563 <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
564 interrupt-names = "pcie", "msi";
565 interrupt-map-mask = <0x0 0x0 0x0 0x7>;
566 interrupt-map = <0 0 0 1 &gicv2 GIC_SPI 143
567 IRQ_TYPE_LEVEL_HIGH>,
568 <0 0 0 2 &gicv2 GIC_SPI 144
569 IRQ_TYPE_LEVEL_HIGH>,
570 <0 0 0 3 &gicv2 GIC_SPI 145
571 IRQ_TYPE_LEVEL_HIGH>,
572 <0 0 0 4 &gicv2 GIC_SPI 146
573 IRQ_TYPE_LEVEL_HIGH>;
574 msi-controller;
575 msi-parent = <&pcie0>;
576
577 ranges = <0x02000000 0x0 0xf8000000 0x6 0x00000000
578 0x0 0x04000000>;
579 /*
580 * The wrapper around the PCIe block has a bug
581 * preventing it from accessing beyond the first 3GB of
582 * memory.
583 */
584 dma-ranges = <0x02000000 0x0 0x00000000 0x0 0x00000000
585 0x0 0xc0000000>;
586 brcm,enable-ssc;
587 };
588
589 genet: ethernet@7d580000 {
590 compatible = "brcm,bcm2711-genet-v5";
591 reg = <0x0 0x7d580000 0x10000>;
592 #address-cells = <0x1>;
593 #size-cells = <0x1>;
594 interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
595 <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
596 status = "disabled";
597
598 genet_mdio: mdio@e14 {
599 compatible = "brcm,genet-mdio-v5";
600 reg = <0xe14 0x8>;
601 reg-names = "mdio";
602 #address-cells = <0x1>;
603 #size-cells = <0x0>;
604 };
605 };
606
607 xhci: usb@7e9c0000 {
608 compatible = "brcm,bcm2711-xhci", "brcm,xhci-brcm-v2";
609 reg = <0x0 0x7e9c0000 0x100000>;
610 #address-cells = <1>;
611 #size-cells = <0>;
612 interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
613 /* DWC2 and this IP block share the same USB PHY,
614 * enabling both at the same time results in lockups.
615 * So keep this node disabled and let the bootloader
616 * decide which interface should be enabled.
617 */
618 status = "disabled";
619 };
620
621 v3d: gpu@7ec00000 {
622 compatible = "brcm,2711-v3d";
623 reg = <0x0 0x7ec00000 0x4000>,
624 <0x0 0x7ec04000 0x4000>;
625 reg-names = "hub", "core0";
626
627 power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
628 resets = <&pm BCM2835_RESET_V3D>;
629 interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
630 };
631 };
632 };
633
634 &clk_osc {
635 clock-frequency = <54000000>;
636 };
637
638 &clocks {
639 compatible = "brcm,bcm2711-cprman";
640 };
641
642 &cpu_thermal {
643 coefficients = <(-487) 410040>;
644 thermal-sensors = <&thermal>;
645 };
646
647 &dsi0 {
648 interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
649 };
650
651 &dsi1 {
652 interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
653 compatible = "brcm,bcm2711-dsi1";
654 };
655
656 &gpio {
657 compatible = "brcm,bcm2711-gpio";
658 interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
659 <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
660 <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
661 <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
662
663 gpio-ranges = <&gpio 0 0 58>;
664
665 gpclk0_gpio49: gpclk0-gpio49 {
666 pin-gpclk {
667 pins = "gpio49";
668 function = "alt1";
669 bias-disable;
670 };
671 };
672 gpclk1_gpio50: gpclk1-gpio50 {
673 pin-gpclk {
674 pins = "gpio50";
675 function = "alt1";
676 bias-disable;
677 };
678 };
679 gpclk2_gpio51: gpclk2-gpio51 {
680 pin-gpclk {
681 pins = "gpio51";
682 function = "alt1";
683 bias-disable;
684 };
685 };
686
687 i2c0_gpio46: i2c0-gpio46 {
688 pin-sda {
689 function = "alt0";
690 pins = "gpio46";
691 bias-pull-up;
692 };
693 pin-scl {
694 function = "alt0";
695 pins = "gpio47";
696 bias-disable;
697 };
698 };
699 i2c1_gpio46: i2c1-gpio46 {
700 pin-sda {
701 function = "alt1";
702 pins = "gpio46";
703 bias-pull-up;
704 };
705 pin-scl {
706 function = "alt1";
707 pins = "gpio47";
708 bias-disable;
709 };
710 };
711 i2c3_gpio2: i2c3-gpio2 {
712 pin-sda {
713 function = "alt5";
714 pins = "gpio2";
715 bias-pull-up;
716 };
717 pin-scl {
718 function = "alt5";
719 pins = "gpio3";
720 bias-disable;
721 };
722 };
723 i2c3_gpio4: i2c3-gpio4 {
724 pin-sda {
725 function = "alt5";
726 pins = "gpio4";
727 bias-pull-up;
728 };
729 pin-scl {
730 function = "alt5";
731 pins = "gpio5";
732 bias-disable;
733 };
734 };
735 i2c4_gpio6: i2c4-gpio6 {
736 pin-sda {
737 function = "alt5";
738 pins = "gpio6";
739 bias-pull-up;
740 };
741 pin-scl {
742 function = "alt5";
743 pins = "gpio7";
744 bias-disable;
745 };
746 };
747 i2c4_gpio8: i2c4-gpio8 {
748 pin-sda {
749 function = "alt5";
750 pins = "gpio8";
751 bias-pull-up;
752 };
753 pin-scl {
754 function = "alt5";
755 pins = "gpio9";
756 bias-disable;
757 };
758 };
759 i2c5_gpio10: i2c5-gpio10 {
760 pin-sda {
761 function = "alt5";
762 pins = "gpio10";
763 bias-pull-up;
764 };
765 pin-scl {
766 function = "alt5";
767 pins = "gpio11";
768 bias-disable;
769 };
770 };
771 i2c5_gpio12: i2c5-gpio12 {
772 pin-sda {
773 function = "alt5";
774 pins = "gpio12";
775 bias-pull-up;
776 };
777 pin-scl {
778 function = "alt5";
779 pins = "gpio13";
780 bias-disable;
781 };
782 };
783 i2c6_gpio0: i2c6-gpio0 {
784 pin-sda {
785 function = "alt5";
786 pins = "gpio0";
787 bias-pull-up;
788 };
789 pin-scl {
790 function = "alt5";
791 pins = "gpio1";
792 bias-disable;
793 };
794 };
795 i2c6_gpio22: i2c6-gpio22 {
796 pin-sda {
797 function = "alt5";
798 pins = "gpio22";
799 bias-pull-up;
800 };
801 pin-scl {
802 function = "alt5";
803 pins = "gpio23";
804 bias-disable;
805 };
806 };
807 i2c_slave_gpio8: i2c-slave-gpio8 {
808 pins-i2c-slave {
809 pins = "gpio8",
810 "gpio9",
811 "gpio10",
812 "gpio11";
813 function = "alt3";
814 };
815 };
816
817 jtag_gpio48: jtag-gpio48 {
818 pins-jtag {
819 pins = "gpio48",
820 "gpio49",
821 "gpio50",
822 "gpio51",
823 "gpio52",
824 "gpio53";
825 function = "alt4";
826 };
827 };
828
829 mii_gpio28: mii-gpio28 {
830 pins-mii {
831 pins = "gpio28",
832 "gpio29",
833 "gpio30",
834 "gpio31";
835 function = "alt4";
836 };
837 };
838 mii_gpio36: mii-gpio36 {
839 pins-mii {
840 pins = "gpio36",
841 "gpio37",
842 "gpio38",
843 "gpio39";
844 function = "alt5";
845 };
846 };
847
848 pcm_gpio50: pcm-gpio50 {
849 pins-pcm {
850 pins = "gpio50",
851 "gpio51",
852 "gpio52",
853 "gpio53";
854 function = "alt2";
855 };
856 };
857
858 pwm0_0_gpio12: pwm0-0-gpio12 {
859 pin-pwm {
860 pins = "gpio12";
861 function = "alt0";
862 bias-disable;
863 };
864 };
865 pwm0_0_gpio18: pwm0-0-gpio18 {
866 pin-pwm {
867 pins = "gpio18";
868 function = "alt5";
869 bias-disable;
870 };
871 };
872 pwm1_0_gpio40: pwm1-0-gpio40 {
873 pin-pwm {
874 pins = "gpio40";
875 function = "alt0";
876 bias-disable;
877 };
878 };
879 pwm0_1_gpio13: pwm0-1-gpio13 {
880 pin-pwm {
881 pins = "gpio13";
882 function = "alt0";
883 bias-disable;
884 };
885 };
886 pwm0_1_gpio19: pwm0-1-gpio19 {
887 pin-pwm {
888 pins = "gpio19";
889 function = "alt5";
890 bias-disable;
891 };
892 };
893 pwm1_1_gpio41: pwm1-1-gpio41 {
894 pin-pwm {
895 pins = "gpio41";
896 function = "alt0";
897 bias-disable;
898 };
899 };
900 pwm0_1_gpio45: pwm0-1-gpio45 {
901 pin-pwm {
902 pins = "gpio45";
903 function = "alt0";
904 bias-disable;
905 };
906 };
907 pwm0_0_gpio52: pwm0-0-gpio52 {
908 pin-pwm {
909 pins = "gpio52";
910 function = "alt1";
911 bias-disable;
912 };
913 };
914 pwm0_1_gpio53: pwm0-1-gpio53 {
915 pin-pwm {
916 pins = "gpio53";
917 function = "alt1";
918 bias-disable;
919 };
920 };
921
922 rgmii_gpio35: rgmii-gpio35 {
923 pin-start-stop {
924 pins = "gpio35";
925 function = "alt4";
926 };
927 pin-rx-ok {
928 pins = "gpio36";
929 function = "alt4";
930 };
931 };
932 rgmii_irq_gpio34: rgmii-irq-gpio34 {
933 pin-irq {
934 pins = "gpio34";
935 function = "alt5";
936 };
937 };
938 rgmii_irq_gpio39: rgmii-irq-gpio39 {
939 pin-irq {
940 pins = "gpio39";
941 function = "alt4";
942 };
943 };
944 rgmii_mdio_gpio28: rgmii-mdio-gpio28 {
945 pins-mdio {
946 pins = "gpio28",
947 "gpio29";
948 function = "alt5";
949 };
950 };
951 rgmii_mdio_gpio37: rgmii-mdio-gpio37 {
952 pins-mdio {
953 pins = "gpio37",
954 "gpio38";
955 function = "alt4";
956 };
957 };
958
959 spi0_gpio46: spi0-gpio46 {
960 pins-spi {
961 pins = "gpio46",
962 "gpio47",
963 "gpio48",
964 "gpio49";
965 function = "alt2";
966 };
967 };
968 spi2_gpio46: spi2-gpio46 {
969 pins-spi {
970 pins = "gpio46",
971 "gpio47",
972 "gpio48",
973 "gpio49",
974 "gpio50";
975 function = "alt5";
976 };
977 };
978 spi3_gpio0: spi3-gpio0 {
979 pins-spi {
980 pins = "gpio0",
981 "gpio1",
982 "gpio2",
983 "gpio3";
984 function = "alt3";
985 };
986 };
987 spi4_gpio4: spi4-gpio4 {
988 pins-spi {
989 pins = "gpio4",
990 "gpio5",
991 "gpio6",
992 "gpio7";
993 function = "alt3";
994 };
995 };
996 spi5_gpio12: spi5-gpio12 {
997 pins-spi {
998 pins = "gpio12",
999 "gpio13",
1000 "gpio14",
1001 "gpio15";
1002 function = "alt3";
1003 };
1004 };
1005 spi6_gpio18: spi6-gpio18 {
1006 pins-spi {
1007 pins = "gpio18",
1008 "gpio19",
1009 "gpio20",
1010 "gpio21";
1011 function = "alt3";
1012 };
1013 };
1014
1015 uart2_gpio0: uart2-gpio0 {
1016 pin-tx {
1017 pins = "gpio0";
1018 function = "alt4";
1019 bias-disable;
1020 };
1021 pin-rx {
1022 pins = "gpio1";
1023 function = "alt4";
1024 bias-pull-up;
1025 };
1026 };
1027 uart2_ctsrts_gpio2: uart2-ctsrts-gpio2 {
1028 pin-cts {
1029 pins = "gpio2";
1030 function = "alt4";
1031 bias-pull-up;
1032 };
1033 pin-rts {
1034 pins = "gpio3";
1035 function = "alt4";
1036 bias-disable;
1037 };
1038 };
1039 uart3_gpio4: uart3-gpio4 {
1040 pin-tx {
1041 pins = "gpio4";
1042 function = "alt4";
1043 bias-disable;
1044 };
1045 pin-rx {
1046 pins = "gpio5";
1047 function = "alt4";
1048 bias-pull-up;
1049 };
1050 };
1051 uart3_ctsrts_gpio6: uart3-ctsrts-gpio6 {
1052 pin-cts {
1053 pins = "gpio6";
1054 function = "alt4";
1055 bias-pull-up;
1056 };
1057 pin-rts {
1058 pins = "gpio7";
1059 function = "alt4";
1060 bias-disable;
1061 };
1062 };
1063 uart4_gpio8: uart4-gpio8 {
1064 pin-tx {
1065 pins = "gpio8";
1066 function = "alt4";
1067 bias-disable;
1068 };
1069 pin-rx {
1070 pins = "gpio9";
1071 function = "alt4";
1072 bias-pull-up;
1073 };
1074 };
1075 uart4_ctsrts_gpio10: uart4-ctsrts-gpio10 {
1076 pin-cts {
1077 pins = "gpio10";
1078 function = "alt4";
1079 bias-pull-up;
1080 };
1081 pin-rts {
1082 pins = "gpio11";
1083 function = "alt4";
1084 bias-disable;
1085 };
1086 };
1087 uart5_gpio12: uart5-gpio12 {
1088 pin-tx {
1089 pins = "gpio12";
1090 function = "alt4";
1091 bias-disable;
1092 };
1093 pin-rx {
1094 pins = "gpio13";
1095 function = "alt4";
1096 bias-pull-up;
1097 };
1098 };
1099 uart5_ctsrts_gpio14: uart5-ctsrts-gpio14 {
1100 pin-cts {
1101 pins = "gpio14";
1102 function = "alt4";
1103 bias-pull-up;
1104 };
1105 pin-rts {
1106 pins = "gpio15";
1107 function = "alt4";
1108 bias-disable;
1109 };
1110 };
1111 };
1112
1113 &rmem {
1114 #address-cells = <2>;
1115 };
1116
1117 &csi0 {
1118 interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
1119 };
1120
1121 &csi1 {
1122 interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
1123 };
1124
1125 &cma {
1126 /*
1127 * arm64 reserves the CMA by default somewhere in ZONE_DMA32,
1128 * that's not good enough for the BCM2711 as some devices can
1129 * only address the lower 1G of memory (ZONE_DMA).
1130 */
1131 alloc-ranges = <0x0 0x00000000 0x40000000>;
1132 };
1133
1134 &i2c0 {
1135 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
1136 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
1137 };
1138
1139 &i2c1 {
1140 compatible = "brcm,bcm2711-i2c", "brcm,bcm2835-i2c";
1141 interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
1142 };
1143
1144 &mailbox {
1145 interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
1146 };
1147
1148 &sdhci {
1149 interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
1150 };
1151
1152 &sdhost {
1153 interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
1154 };
1155
1156 &spi {
1157 interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
1158 };
1159
1160 &spi1 {
1161 interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
1162 };
1163
1164 &spi2 {
1165 interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
1166 };
1167
1168 &system_timer {
1169 interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
1170 <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
1171 <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
1172 <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
1173 };
1174
1175 &txp {
1176 interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
1177 };
1178
1179 &uart0 {
1180 interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
1181 };
1182
1183 &uart1 {
1184 interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
1185 };
1186
1187 &usb {
1188 interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
1189 };
1190
1191 &vec {
1192 compatible = "brcm,bcm2711-vec";
1193 interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
1194 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.