1 // SPDX-License-Identifier: BSD-3-Clause
2
3 /dts-v1/;
4
5 #include "qcom-msm8226.dtsi"
6 #include "pm8226.dtsi"
7
8 /delete-node/ &smem_region;
9
10 / {
11 model = "Motorola Moto G 4G (2013)";
12 compatible = "motorola,peregrine", "qcom,msm8926", "qcom,msm8226";
13 chassis-type = "handset";
14
15 aliases {
16 mmc0 = &sdhc_1; /* SDC1 eMMC slot */
17 mmc1 = &sdhc_2; /* SDC2 SD card slot */
18 };
19
20 chosen {
21 #address-cells = <1>;
22 #size-cells = <1>;
23 ranges;
24
25 framebuffer0: framebuffer@3200000 {
26 compatible = "simple-framebuffer";
27 reg = <0x03200000 0x800000>;
28 width = <720>;
29 height = <1280>;
30 stride = <(720 * 3)>;
31 format = "r8g8b8";
32 vsp-supply = <®_lcd_pos>;
33 vsn-supply = <®_lcd_neg>;
34 vdd-supply = <&pm8226_l28>;
35 vddio-supply = <&vddio_disp_vreg>;
36 };
37 };
38
39 gpio-keys {
40 compatible = "gpio-keys";
41
42 event-hall-sensor {
43 label = "Hall Effect Sensor";
44 gpios = <&tlmm 51 GPIO_ACTIVE_LOW>;
45 linux,input-type = <EV_SW>;
46 linux,code = <SW_LID>;
47 linux,can-disable;
48 };
49
50 key-volume-up {
51 label = "Volume Up";
52 gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
53 linux,code = <KEY_VOLUMEUP>;
54 debounce-interval = <15>;
55 };
56 };
57
58 vddio_disp_vreg: regulator-vddio-disp {
59 compatible = "regulator-fixed";
60 regulator-name = "vddio_disp";
61 gpio = <&tlmm 34 GPIO_ACTIVE_HIGH>;
62 startup-delay-us = <300>;
63 enable-active-high;
64 regulator-boot-on;
65 vin-supply = <&pm8226_l8>;
66 pinctrl-0 = <&disp_vddio_default>;
67 pinctrl-names = "default";
68 };
69
70 reserved-memory {
71 #address-cells = <1>;
72 #size-cells = <1>;
73 ranges;
74
75 framebuffer@3200000 {
76 reg = <0x03200000 0x800000>;
77 no-map;
78 };
79
80 smem_region: smem@fa00000 {
81 reg = <0x0fa00000 0x100000>;
82 no-map;
83 };
84 };
85 };
86
87 &blsp1_i2c2 {
88 clock-frequency = <100000>;
89 status = "okay";
90
91 magnetometer@c {
92 compatible = "asahi-kasei,ak8963";
93 reg = <0xc>;
94 interrupts-extended = <&tlmm 38 IRQ_TYPE_EDGE_FALLING>;
95 reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
96 vdd-supply = <&pm8226_l19>;
97 pinctrl-0 = <&mag_int_default &mag_reset_default>;
98 pinctrl-names = "default";
99 };
100
101 accelerometer@18 {
102 compatible = "st,lis3dh-accel";
103 reg = <0x18>;
104 interrupts-extended = <&tlmm 1 IRQ_TYPE_EDGE_FALLING>;
105 vdd-supply = <&pm8226_l19>;
106 pinctrl-0 = <&accel_int_default>;
107 pinctrl-names = "default";
108 st,drdy-int-pin = <1>;
109 };
110 };
111
112 &blsp1_i2c3 {
113 clock-frequency = <400000>;
114 status = "okay";
115
116 regulator@3e {
117 compatible = "ti,tps65132";
118 reg = <0x3e>;
119 pinctrl-0 = <®_lcd_default>;
120 pinctrl-names = "default";
121
122 reg_lcd_pos: outp {
123 regulator-name = "outp";
124 regulator-min-microvolt = <4000000>;
125 regulator-max-microvolt = <6000000>;
126 regulator-active-discharge = <1>;
127 regulator-boot-on;
128 enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
129 };
130
131 reg_lcd_neg: outn {
132 regulator-name = "outn";
133 regulator-min-microvolt = <4000000>;
134 regulator-max-microvolt = <6000000>;
135 regulator-active-discharge = <1>;
136 regulator-boot-on;
137 enable-gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>;
138 };
139 };
140
141 sensor@48 {
142 compatible = "ti,tmp108";
143 reg = <0x48>;
144 interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
145 pinctrl-0 = <&temp_alert_default>;
146 pinctrl-names = "default";
147 #thermal-sensor-cells = <0>;
148 };
149 };
150
151 &blsp1_uart3 {
152 status = "okay";
153 };
154
155 &pm8226_resin {
156 linux,code = <KEY_VOLUMEDOWN>;
157 status = "okay";
158 };
159
160 &pm8226_vib {
161 status = "okay";
162 };
163
164 &rpm_requests {
165 regulators {
166 compatible = "qcom,rpm-pm8226-regulators";
167
168 pm8226_s3: s3 {
169 regulator-min-microvolt = <1200000>;
170 regulator-max-microvolt = <1300000>;
171 };
172
173 pm8226_s4: s4 {
174 regulator-min-microvolt = <1800000>;
175 regulator-max-microvolt = <2200000>;
176 };
177
178 pm8226_s5: s5 {
179 regulator-min-microvolt = <1150000>;
180 regulator-max-microvolt = <1150000>;
181 };
182
183 pm8226_l1: l1 {
184 regulator-min-microvolt = <1225000>;
185 regulator-max-microvolt = <1225000>;
186 };
187
188 pm8226_l2: l2 {
189 regulator-min-microvolt = <1200000>;
190 regulator-max-microvolt = <1200000>;
191 };
192
193 pm8226_l3: l3 {
194 regulator-min-microvolt = <750000>;
195 regulator-max-microvolt = <1337500>;
196 };
197
198 pm8226_l4: l4 {
199 regulator-min-microvolt = <1200000>;
200 regulator-max-microvolt = <1200000>;
201 };
202
203 pm8226_l5: l5 {
204 regulator-min-microvolt = <1200000>;
205 regulator-max-microvolt = <1200000>;
206 };
207
208 pm8226_l6: l6 {
209 regulator-min-microvolt = <1800000>;
210 regulator-max-microvolt = <1800000>;
211 regulator-allow-set-load;
212 };
213
214 pm8226_l7: l7 {
215 regulator-min-microvolt = <1850000>;
216 regulator-max-microvolt = <1850000>;
217 };
218
219 pm8226_l8: l8 {
220 regulator-min-microvolt = <1800000>;
221 regulator-max-microvolt = <1800000>;
222 };
223
224 pm8226_l9: l9 {
225 regulator-min-microvolt = <2050000>;
226 regulator-max-microvolt = <2050000>;
227 };
228
229 pm8226_l10: l10 {
230 regulator-min-microvolt = <1800000>;
231 regulator-max-microvolt = <1800000>;
232 };
233
234 pm8226_l12: l12 {
235 regulator-min-microvolt = <1800000>;
236 regulator-max-microvolt = <1800000>;
237 };
238
239 pm8226_l14: l14 {
240 regulator-min-microvolt = <2750000>;
241 regulator-max-microvolt = <2750000>;
242 };
243
244 pm8226_l15: l15 {
245 regulator-min-microvolt = <2800000>;
246 regulator-max-microvolt = <2800000>;
247 };
248
249 pm8226_l16: l16 {
250 regulator-min-microvolt = <3000000>;
251 regulator-max-microvolt = <3350000>;
252 };
253
254 pm8226_l17: l17 {
255 regulator-min-microvolt = <2950000>;
256 regulator-max-microvolt = <2950000>;
257 };
258
259 pm8226_l18: l18 {
260 regulator-min-microvolt = <2950000>;
261 regulator-max-microvolt = <2950000>;
262 };
263
264 pm8226_l19: l19 {
265 regulator-min-microvolt = <2850000>;
266 regulator-max-microvolt = <2850000>;
267 };
268
269 pm8226_l20: l20 {
270 regulator-min-microvolt = <3075000>;
271 regulator-max-microvolt = <3075000>;
272 };
273
274 pm8226_l21: l21 {
275 regulator-min-microvolt = <1800000>;
276 regulator-max-microvolt = <2950000>;
277 regulator-allow-set-load;
278 };
279
280 pm8226_l22: l22 {
281 regulator-min-microvolt = <1800000>;
282 regulator-max-microvolt = <2950000>;
283 };
284
285 pm8226_l23: l23 {
286 regulator-min-microvolt = <1800000>;
287 regulator-max-microvolt = <2950000>;
288 };
289
290 pm8226_l24: l24 {
291 regulator-min-microvolt = <1300000>;
292 regulator-max-microvolt = <1350000>;
293 };
294
295 pm8226_l25: l25 {
296 regulator-min-microvolt = <1775000>;
297 regulator-max-microvolt = <2125000>;
298 };
299
300 pm8226_l26: l26 {
301 regulator-min-microvolt = <1225000>;
302 regulator-max-microvolt = <1225000>;
303 };
304
305 pm8226_l27: l27 {
306 regulator-min-microvolt = <2050000>;
307 regulator-max-microvolt = <2050000>;
308 };
309
310 pm8226_l28: l28 {
311 regulator-min-microvolt = <1800000>;
312 regulator-max-microvolt = <3400000>;
313 regulator-boot-on;
314 };
315
316 pm8226_lvs1: lvs1 {
317 /* Pull-up for I2C lines */
318 regulator-always-on;
319 };
320 };
321 };
322
323 &sdhc_1 {
324 vmmc-supply = <&pm8226_l17>;
325 vqmmc-supply = <&pm8226_l6>;
326
327 bus-width = <8>;
328 non-removable;
329
330 status = "okay";
331 };
332
333 &sdhc_2 {
334 vmmc-supply = <&pm8226_l18>;
335 vqmmc-supply = <&pm8226_l21>;
336
337 bus-width = <4>;
338 cd-gpios = <&tlmm 115 GPIO_ACTIVE_HIGH>;
339
340 status = "okay";
341 };
342
343 &smbb {
344 qcom,fast-charge-safe-current = <2000000>;
345 qcom,fast-charge-current-limit = <1900000>;
346 qcom,fast-charge-safe-voltage = <4400000>;
347 qcom,minimum-input-voltage = <4300000>;
348
349 status = "okay";
350 };
351
352 &tlmm {
353 accel_int_default: accel-int-default-state {
354 pins = "gpio1";
355 function = "gpio";
356 drive-strength = <2>;
357 bias-disable;
358 output-disable;
359 };
360
361 disp_vddio_default: disp-vddio-default-state {
362 pins = "gpio34";
363 function = "gpio";
364 drive-strength = <2>;
365 bias-disable;
366 output-high;
367 };
368
369 mag_int_default: mag-int-default-state {
370 pins = "gpio38";
371 function = "gpio";
372 drive-strength = <2>;
373 bias-disable;
374 output-disable;
375 };
376
377 mag_reset_default: mag-reset-default-state {
378 pins = "gpio62";
379 function = "gpio";
380 drive-strength = <2>;
381 bias-disable;
382 output-high;
383 };
384
385 reg_lcd_default: reg-lcd-default-state {
386 pins = "gpio31", "gpio33";
387 function = "gpio";
388 drive-strength = <2>;
389 bias-disable;
390 output-high;
391 };
392
393 temp_alert_default: temp-alert-default-state {
394 pins = "gpio13";
395 function = "gpio";
396 drive-strength = <2>;
397 bias-disable;
398 output-disable;
399 };
400 };
401
402 &usb {
403 extcon = <&smbb>;
404 dr_mode = "peripheral";
405 status = "okay";
406 };
407
408 &usb_hs_phy {
409 extcon = <&smbb>;
410 v1p8-supply = <&pm8226_l10>;
411 v3p3-supply = <&pm8226_l20>;
412 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.