1 // SPDX-License-Identifier: GPL-2.0
2 #include "qcom-msm8974pro.dtsi"
3 #include "pm8841.dtsi"
4 #include "pm8941.dtsi"
5 #include <dt-bindings/input/input.h>
6 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
7
8 / {
9 model = "OnePlus One";
10 compatible = "oneplus,bacon", "qcom,msm8974pro", "qcom,msm8974";
11 chassis-type = "handset";
12 qcom,msm-id = <194 0x10000>;
13 qcom,board-id = <8 0>;
14
15 aliases {
16 serial0 = &blsp1_uart2;
17 };
18
19 chosen {
20 stdout-path = "serial0:115200n8";
21 };
22
23 gpio-keys {
24 compatible = "gpio-keys";
25
26 pinctrl-0 = <&gpio_keys_default>, <&gpio_hall_sensor_default>;
27 pinctrl-names = "default";
28
29 key-volume-down {
30 label = "Volume Down";
31 gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
32 linux,code = <KEY_VOLUMEDOWN>;
33 wakeup-source;
34 debounce-interval = <15>;
35 };
36
37 key-volume-up {
38 label = "Volume Up";
39 gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
40 linux,code = <KEY_VOLUMEUP>;
41 wakeup-source;
42 debounce-interval = <15>;
43 };
44
45 event-hall-sensor {
46 label = "Hall Effect Sensor";
47 gpios = <&tlmm 68 GPIO_ACTIVE_LOW>;
48 linux,input-type = <EV_SW>;
49 linux,code = <SW_LID>;
50 linux,can-disable;
51 debounce-interval = <150>;
52 };
53 };
54
55 vreg_boost: vreg-boost {
56 compatible = "regulator-fixed";
57
58 regulator-name = "vreg-boost";
59 regulator-min-microvolt = <3150000>;
60 regulator-max-microvolt = <3150000>;
61
62 regulator-always-on;
63 regulator-boot-on;
64
65 gpio = <&pm8941_gpios 21 GPIO_ACTIVE_HIGH>;
66 enable-active-high;
67
68 pinctrl-names = "default";
69 pinctrl-0 = <&boost_bypass_n_pin>;
70 };
71
72 vreg_vph_pwr: vreg-vph-pwr {
73 compatible = "regulator-fixed";
74 regulator-name = "vph-pwr";
75
76 regulator-min-microvolt = <3600000>;
77 regulator-max-microvolt = <3600000>;
78
79 regulator-always-on;
80 };
81 };
82
83 &blsp1_i2c1 {
84 status = "okay";
85
86 fuel-gauge@55 {
87 compatible = "ti,bq27541";
88 reg = <0x55>;
89 power-supplies = <&bq24196_charger>;
90 };
91 };
92
93 &blsp1_i2c2 {
94 status = "okay";
95
96 rmi4-i2c-dev@20 {
97 compatible = "syna,rmi4-i2c";
98 reg = <0x20>;
99
100 syna,startup-delay-ms = <100>;
101
102 interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
103 vdd-supply = <&pm8941_l22>;
104 vio-supply = <&pm8941_lvs3>;
105
106 pinctrl-names = "default";
107 pinctrl-0 = <&touch_default_state>;
108
109 #address-cells = <1>;
110 #size-cells = <0>;
111
112 rmi4-f01@1 {
113 reg = <0x1>;
114 syna,nosleep-mode = <1>;
115 };
116
117 rmi4-f12@12 {
118 reg = <0x12>;
119 syna,sensor-type = <1>;
120 /*
121 * Touchscreen size is 2040x1080, y-values between
122 * 1920-2040 are used for touchkey (menu, home & back).
123 * For now clip it off so we don't get touch events
124 * outside of the display area.
125 */
126 syna,clip-y-high = <1920>;
127 };
128 };
129
130 led-controller@36 {
131 compatible = "ti,lm3630a";
132 reg = <0x36>;
133
134 #address-cells = <1>;
135 #size-cells = <0>;
136
137 led@0 {
138 reg = <0>;
139 led-sources = <0 1>;
140 label = "lcd-backlight";
141 default-brightness = <80>;
142 };
143 };
144
145 led-controller@68 {
146 compatible = "si-en,sn3193";
147 reg = <0x68>;
148
149 shutdown-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
150
151 #address-cells = <1>;
152 #size-cells = <0>;
153
154 led@1 {
155 reg = <1>;
156 label = "red:status";
157 led-max-microamp = <17500>;
158 };
159
160 led@2 {
161 reg = <2>;
162 label = "green:status";
163 led-max-microamp = <17500>;
164 };
165
166 led@3 {
167 reg = <3>;
168 label = "blue:status";
169 led-max-microamp = <17500>;
170 };
171 };
172 };
173
174 &blsp1_i2c6 {
175 status = "okay";
176
177 bq24196_charger: charger@6b {
178 compatible = "ti,bq24196";
179 reg = <0x6b>;
180 interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
181 omit-battery-class;
182 };
183 };
184
185 &blsp1_uart2 {
186 status = "okay";
187 };
188
189 &gcc {
190 compatible = "qcom,gcc-msm8974pro-ac";
191 };
192
193 &pm8941_coincell {
194 qcom,rset-ohms = <800>;
195 qcom,vset-millivolts = <3200>;
196
197 status = "okay";
198 };
199
200 &pm8941_gpios {
201 gpio_keys_default: gpio-keys-active-state {
202 pins = "gpio2", "gpio5";
203 function = "normal";
204 input-enable;
205 bias-disable;
206 power-source = <PM8941_GPIO_S3>;
207 };
208 };
209
210 &pm8941_vib {
211 status = "okay";
212 };
213
214 &pronto {
215 vddmx-supply = <&pm8841_s1>;
216 vddcx-supply = <&pm8841_s2>;
217 vddpx-supply = <&pm8941_s3>;
218
219 pinctrl-names = "default";
220 pinctrl-0 = <&wcnss_pin_a>;
221
222 status = "okay";
223
224 iris {
225 vddxo-supply = <&pm8941_l6>;
226 vddrfa-supply = <&pm8941_l11>;
227 vddpa-supply = <&pm8941_l19>;
228 vdddig-supply = <&pm8941_s3>;
229 };
230
231 smd-edge {
232 qcom,remote-pid = <4>;
233 label = "pronto";
234
235 wcnss {
236 status = "okay";
237 };
238 };
239 };
240
241 &remoteproc_adsp {
242 cx-supply = <&pm8841_s2>;
243
244 status = "okay";
245 };
246
247 &rpm_requests {
248 regulators-0 {
249 compatible = "qcom,rpm-pm8841-regulators";
250
251 pm8841_s1: s1 {
252 regulator-min-microvolt = <675000>;
253 regulator-max-microvolt = <1050000>;
254 };
255
256 pm8841_s2: s2 {
257 regulator-min-microvolt = <875000>;
258 regulator-max-microvolt = <1050000>;
259 regulator-always-on;
260 };
261
262 pm8841_s3: s3 {
263 regulator-min-microvolt = <1050000>;
264 regulator-max-microvolt = <1050000>;
265 };
266 };
267
268 regulators-1 {
269 compatible = "qcom,rpm-pm8941-regulators";
270
271 vdd_l1_l3-supply = <&pm8941_s1>;
272 vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
273 vdd_l4_l11-supply = <&pm8941_s1>;
274 vdd_l5_l7-supply = <&pm8941_s2>;
275 vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
276 vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
277 vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
278 vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
279 vdd_l21-supply = <&vreg_boost>;
280
281 pm8941_s1: s1 {
282 regulator-min-microvolt = <1300000>;
283 regulator-max-microvolt = <1300000>;
284
285 regulator-always-on;
286 regulator-boot-on;
287 };
288
289 pm8941_s2: s2 {
290 regulator-min-microvolt = <2150000>;
291 regulator-max-microvolt = <2150000>;
292
293 regulator-boot-on;
294 };
295
296 pm8941_s3: s3 {
297 regulator-min-microvolt = <1800000>;
298 regulator-max-microvolt = <1800000>;
299 regulator-system-load = <154000>;
300
301 regulator-always-on;
302 regulator-boot-on;
303 regulator-allow-set-load;
304 };
305
306 pm8941_l1: l1 {
307 regulator-min-microvolt = <1225000>;
308 regulator-max-microvolt = <1225000>;
309
310 regulator-always-on;
311 regulator-boot-on;
312 };
313
314 pm8941_l2: l2 {
315 regulator-min-microvolt = <1200000>;
316 regulator-max-microvolt = <1200000>;
317 };
318
319 pm8941_l3: l3 {
320 regulator-min-microvolt = <1225000>;
321 regulator-max-microvolt = <1225000>;
322 };
323
324 pm8941_l4: l4 {
325 regulator-min-microvolt = <1225000>;
326 regulator-max-microvolt = <1225000>;
327 };
328
329 pm8941_l5: l5 {
330 regulator-min-microvolt = <1800000>;
331 regulator-max-microvolt = <1800000>;
332 };
333
334 pm8941_l6: l6 {
335 regulator-min-microvolt = <1800000>;
336 regulator-max-microvolt = <1800000>;
337
338 regulator-boot-on;
339 };
340
341 pm8941_l7: l7 {
342 regulator-min-microvolt = <1800000>;
343 regulator-max-microvolt = <1800000>;
344
345 regulator-boot-on;
346 };
347
348 pm8941_l8: l8 {
349 regulator-min-microvolt = <1800000>;
350 regulator-max-microvolt = <1800000>;
351 };
352
353 pm8941_l9: l9 {
354 regulator-min-microvolt = <1800000>;
355 regulator-max-microvolt = <2950000>;
356 };
357
358 pm8941_l10: l10 {
359 regulator-min-microvolt = <1800000>;
360 regulator-max-microvolt = <2950000>;
361 };
362
363 pm8941_l11: l11 {
364 regulator-min-microvolt = <1225000>;
365 regulator-max-microvolt = <1350000>;
366 };
367
368 pm8941_l12: l12 {
369 regulator-min-microvolt = <1800000>;
370 regulator-max-microvolt = <1800000>;
371
372 regulator-always-on;
373 regulator-boot-on;
374 regulator-allow-set-load;
375 };
376
377 pm8941_l13: l13 {
378 regulator-min-microvolt = <1800000>;
379 regulator-max-microvolt = <2950000>;
380
381 regulator-boot-on;
382 };
383
384 pm8941_l14: l14 {
385 regulator-min-microvolt = <1800000>;
386 regulator-max-microvolt = <1800000>;
387 };
388
389 pm8941_l15: l15 {
390 regulator-min-microvolt = <2050000>;
391 regulator-max-microvolt = <2050000>;
392 };
393
394 pm8941_l16: l16 {
395 regulator-min-microvolt = <2700000>;
396 regulator-max-microvolt = <2700000>;
397 };
398
399 pm8941_l17: l17 {
400 regulator-min-microvolt = <2850000>;
401 regulator-max-microvolt = <2850000>;
402 };
403
404 pm8941_l18: l18 {
405 regulator-min-microvolt = <2850000>;
406 regulator-max-microvolt = <2850000>;
407 };
408
409 pm8941_l19: l19 {
410 regulator-min-microvolt = <2900000>;
411 regulator-max-microvolt = <3350000>;
412 };
413
414 pm8941_l20: l20 {
415 regulator-min-microvolt = <2950000>;
416 regulator-max-microvolt = <2950000>;
417
418 regulator-system-load = <200000>;
419 regulator-allow-set-load;
420 regulator-boot-on;
421 };
422
423 pm8941_l21: l21 {
424 regulator-min-microvolt = <2950000>;
425 regulator-max-microvolt = <2950000>;
426
427 regulator-boot-on;
428 };
429
430 pm8941_l22: l22 {
431 regulator-min-microvolt = <3000000>;
432 regulator-max-microvolt = <3000000>;
433 regulator-allow-set-load;
434 };
435
436 pm8941_l23: l23 {
437 regulator-min-microvolt = <3000000>;
438 regulator-max-microvolt = <3000000>;
439 };
440
441 pm8941_l24: l24 {
442 regulator-min-microvolt = <3075000>;
443 regulator-max-microvolt = <3075000>;
444
445 regulator-boot-on;
446 };
447
448 pm8941_lvs3: lvs3 {};
449 };
450 };
451
452 &sdhc_1 {
453 vmmc-supply = <&pm8941_l20>;
454 vqmmc-supply = <&pm8941_s3>;
455
456 pinctrl-names = "default", "sleep";
457 pinctrl-0 = <&sdc1_on>;
458 pinctrl-1 = <&sdc1_off>;
459
460 status = "okay";
461 };
462
463 &smbb {
464 status = "okay";
465 };
466
467 &tlmm {
468 gpio_hall_sensor_default: gpio-hall-sensor-default-state {
469 pins = "gpio68";
470 function = "gpio";
471 drive-strength = <8>;
472 bias-pull-up;
473 };
474
475 sdc1_on: sdc1-on-state {
476 clk-pins {
477 pins = "sdc1_clk";
478 drive-strength = <4>;
479 bias-disable;
480 };
481
482 cmd-data-pins {
483 pins = "sdc1_cmd", "sdc1_data";
484 drive-strength = <4>;
485 bias-pull-up;
486 };
487 };
488
489 touch_default_state: touch-default-state {
490 int-pins {
491 pins = "gpio61";
492 function = "gpio";
493 drive-strength = <2>;
494 bias-disable;
495 };
496
497 reset-pins {
498 pins = "gpio60";
499 function = "gpio";
500 drive-strength = <2>;
501 bias-pull-up;
502 };
503 };
504
505 wcnss_pin_a: wcnss-pin-active-state {
506 wlan-pins {
507 pins = "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
508 function = "wlan";
509 drive-strength = <6>;
510 bias-pull-down;
511 };
512
513 bt-pins {
514 pins = "gpio35", "gpio43", "gpio44";
515 function = "bt";
516 drive-strength = <2>;
517 bias-pull-down;
518 };
519 };
520 };
521
522 &usb {
523 phys = <&usb_hs1_phy>;
524 phy-select = <&tcsr 0xb000 0>;
525 extcon = <&smbb>, <&usb_id>;
526 vbus-supply = <&chg_otg>;
527
528 hnp-disable;
529 srp-disable;
530 adp-disable;
531
532 status = "okay";
533 };
534
535 &usb_hs1_phy {
536 status = "okay";
537
538 v1p8-supply = <&pm8941_l6>;
539 v3p3-supply = <&pm8941_l24>;
540
541 extcon = <&smbb>;
542 qcom,init-seq = /bits/ 8 <0x1 0x64>;
543 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.