1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
4 */
5 #include "omap5.dtsi"
6 #include <dt-bindings/interrupt-controller/irq.h>
7 #include <dt-bindings/interrupt-controller/arm-gic.h>
8
9 / {
10 aliases {
11 display0 = &hdmi0;
12 };
13
14 chosen {
15 stdout-path = &uart3;
16 };
17
18 vmain: fixedregulator-vmain {
19 compatible = "regulator-fixed";
20 regulator-name = "vmain";
21 regulator-min-microvolt = <5000000>;
22 regulator-max-microvolt = <5000000>;
23 };
24
25 vsys_cobra: fixedregulator-vsys_cobra {
26 compatible = "regulator-fixed";
27 regulator-name = "vsys_cobra";
28 vin-supply = <&vmain>;
29 regulator-min-microvolt = <5000000>;
30 regulator-max-microvolt = <5000000>;
31 };
32
33 vmmcsd_fixed: fixedregulator-mmcsd {
34 compatible = "regulator-fixed";
35 regulator-name = "vmmcsd_fixed";
36 regulator-min-microvolt = <3000000>;
37 regulator-max-microvolt = <3000000>;
38 };
39
40 mmc3_pwrseq: sdhci0_pwrseq {
41 compatible = "mmc-pwrseq-simple";
42 clocks = <&clk32kgaudio>;
43 clock-names = "ext_clock";
44 };
45
46 vmmcsdio_fixed: fixedregulator-mmcsdio {
47 compatible = "regulator-fixed";
48 regulator-name = "vmmcsdio_fixed";
49 regulator-min-microvolt = <1800000>;
50 regulator-max-microvolt = <1800000>;
51 gpio = <&gpio5 12 GPIO_ACTIVE_HIGH>; /* gpio140 WLAN_EN */
52 enable-active-high;
53 startup-delay-us = <70000>;
54 pinctrl-names = "default";
55 pinctrl-0 = <&wlan_pins>;
56 };
57
58 /* HS USB Host PHY on PORT 2 */
59 hsusb2_phy: hsusb2-phy-pins {
60 compatible = "usb-nop-xceiv";
61 reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */
62 clocks = <&auxclk1_ck>;
63 clock-names = "main_clk";
64 clock-frequency = <19200000>;
65 #phy-cells = <0>;
66 };
67
68 /* HS USB Host PHY on PORT 3 */
69 hsusb3_phy: hsusb3_phy {
70 compatible = "usb-nop-xceiv";
71 reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
72 #phy-cells = <0>;
73 };
74
75 tpd12s015: encoder {
76 compatible = "ti,tpd12s015";
77
78 pinctrl-names = "default";
79 pinctrl-0 = <&tpd12s015_pins>;
80
81 /* gpios defined in the board specific dts */
82
83 ports {
84 #address-cells = <1>;
85 #size-cells = <0>;
86
87 port@0 {
88 reg = <0>;
89
90 tpd12s015_in: endpoint {
91 remote-endpoint = <&hdmi_out>;
92 };
93 };
94
95 port@1 {
96 reg = <1>;
97
98 tpd12s015_out: endpoint {
99 remote-endpoint = <&hdmi_connector_in>;
100 };
101 };
102 };
103 };
104
105 hdmi0: connector {
106 compatible = "hdmi-connector";
107 label = "hdmi";
108
109 type = "b";
110
111 port {
112 hdmi_connector_in: endpoint {
113 remote-endpoint = <&tpd12s015_out>;
114 };
115 };
116 };
117
118 sound: sound {
119 compatible = "ti,abe-twl6040";
120 ti,model = "omap5-uevm";
121
122 ti,jack-detection;
123 ti,mclk-freq = <19200000>;
124
125 ti,mcpdm = <&mcpdm>;
126
127 ti,twl6040 = <&twl6040>;
128
129 /* Audio routing */
130 ti,audio-routing =
131 "Headset Stereophone", "HSOL",
132 "Headset Stereophone", "HSOR",
133 "Line Out", "AUXL",
134 "Line Out", "AUXR",
135 "HSMIC", "Headset Mic",
136 "Headset Mic", "Headset Mic Bias",
137 "AFML", "Line In",
138 "AFMR", "Line In";
139 };
140 };
141
142 &gpio8 {
143 /* TI trees use GPIO instead of msecure, see also muxing */
144 msecure-hog {
145 gpio-hog;
146 gpios = <10 GPIO_ACTIVE_HIGH>;
147 output-high;
148 line-name = "gpio8_234/msecure";
149 };
150 };
151
152 &omap5_pmx_core {
153 pinctrl-names = "default";
154 pinctrl-0 = <
155 &usbhost_pins
156 &led_gpio_pins
157 >;
158
159 twl6040_pins: twl6040-pins {
160 pinctrl-single,pins = <
161 OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6) /* mcspi1_somi.gpio5_141 */
162 >;
163 };
164
165 mcpdm_pins: mcpdm-pins {
166 pinctrl-single,pins = <
167 OMAP5_IOPAD(0x182, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */
168 OMAP5_IOPAD(0x19c, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */
169 OMAP5_IOPAD(0x19e, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */
170 OMAP5_IOPAD(0x1a0, PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */
171 OMAP5_IOPAD(0x1a2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */
172 >;
173 };
174
175 mcbsp1_pins: mcbsp1-pins {
176 pinctrl-single,pins = <
177 OMAP5_IOPAD(0x18c, PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */
178 OMAP5_IOPAD(0x18e, PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */
179 OMAP5_IOPAD(0x190, PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */
180 OMAP5_IOPAD(0x192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */
181 >;
182 };
183
184 mcbsp2_pins: mcbsp2-pins {
185 pinctrl-single,pins = <
186 OMAP5_IOPAD(0x194, PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */
187 OMAP5_IOPAD(0x196, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */
188 OMAP5_IOPAD(0x198, PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */
189 OMAP5_IOPAD(0x19a, PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */
190 >;
191 };
192
193 i2c1_pins: i2c1-pins {
194 pinctrl-single,pins = <
195 OMAP5_IOPAD(0x1f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */
196 OMAP5_IOPAD(0x1f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */
197 >;
198 };
199
200 mcspi2_pins: mcspi2-pins {
201 pinctrl-single,pins = <
202 OMAP5_IOPAD(0x0fc, PIN_INPUT | MUX_MODE0) /* mcspi2_clk */
203 OMAP5_IOPAD(0x0fe, PIN_INPUT | MUX_MODE0) /* mcspi2_simo */
204 OMAP5_IOPAD(0x100, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */
205 OMAP5_IOPAD(0x102, PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0 */
206 >;
207 };
208
209 mcspi3_pins: mcspi3-pins {
210 pinctrl-single,pins = <
211 OMAP5_IOPAD(0x0b8, PIN_INPUT | MUX_MODE1) /* mcspi3_somi */
212 OMAP5_IOPAD(0x0ba, PIN_INPUT | MUX_MODE1) /* mcspi3_cs0 */
213 OMAP5_IOPAD(0x0bc, PIN_INPUT | MUX_MODE1) /* mcspi3_simo */
214 OMAP5_IOPAD(0x0be, PIN_INPUT | MUX_MODE1) /* mcspi3_clk */
215 >;
216 };
217
218 mmc3_pins: mmc3-pins {
219 pinctrl-single,pins = <
220 OMAP5_IOPAD(0x01a4, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_clk */
221 OMAP5_IOPAD(0x01a6, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_cmd */
222 OMAP5_IOPAD(0x01a8, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data0 */
223 OMAP5_IOPAD(0x01aa, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data1 */
224 OMAP5_IOPAD(0x01ac, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data2 */
225 OMAP5_IOPAD(0x01ae, PIN_INPUT_PULLUP | MUX_MODE0) /* wlsdio_data3 */
226 >;
227 };
228
229 wlan_pins: wlan-pins {
230 pinctrl-single,pins = <
231 OMAP5_IOPAD(0x1bc, PIN_OUTPUT | MUX_MODE6) /* mcspi1_clk.gpio5_140 */
232 >;
233 };
234
235 /* TI trees use GPIO mode; msecure mode does not work reliably? */
236 palmas_msecure_pins: palmas-msecure-pins {
237 pinctrl-single,pins = <
238 OMAP5_IOPAD(0x180, PIN_OUTPUT | MUX_MODE6) /* gpio8_234 */
239 >;
240 };
241
242 usbhost_pins: usbhost-pins {
243 pinctrl-single,pins = <
244 OMAP5_IOPAD(0x0c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */
245 OMAP5_IOPAD(0x0c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */
246
247 OMAP5_IOPAD(0x1de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */
248 OMAP5_IOPAD(0x1e0, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */
249
250 OMAP5_IOPAD(0x0b0, PIN_OUTPUT | MUX_MODE6) /* gpio3_80 HUB_NRESET */
251 OMAP5_IOPAD(0x0ae, PIN_OUTPUT | MUX_MODE6) /* gpio3_79 ETH_NRESET */
252 >;
253 };
254
255 led_gpio_pins: led-gpio-pins {
256 pinctrl-single,pins = <
257 OMAP5_IOPAD(0x1d6, PIN_OUTPUT | MUX_MODE6) /* uart3_cts_rctx.gpio5_153 */
258 >;
259 };
260
261 uart1_pins: uart1-pins {
262 pinctrl-single,pins = <
263 OMAP5_IOPAD(0x0a0, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_cts */
264 OMAP5_IOPAD(0x0a2, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_tx.uart1_cts */
265 OMAP5_IOPAD(0x0a4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rx.uart1_rts */
266 OMAP5_IOPAD(0x0a6, PIN_OUTPUT | MUX_MODE0) /* uart1_rx.uart1_rts */
267 >;
268 };
269
270 uart3_pins: uart3-pins {
271 pinctrl-single,pins = <
272 OMAP5_IOPAD(0x1da, PIN_OUTPUT | MUX_MODE0) /* uart3_rts_irsd.uart3_tx_irtx */
273 OMAP5_IOPAD(0x1dc, PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_rx_irrx.uart3_usbb3_hsic */
274 >;
275 };
276
277 uart5_pins: uart5-pins {
278 pinctrl-single,pins = <
279 OMAP5_IOPAD(0x1b0, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_rx.uart5_rx */
280 OMAP5_IOPAD(0x1b2, PIN_OUTPUT | MUX_MODE0) /* uart5_tx.uart5_tx */
281 OMAP5_IOPAD(0x1b4, PIN_INPUT_PULLUP | MUX_MODE0) /* uart5_cts.uart5_rts */
282 OMAP5_IOPAD(0x1b6, PIN_OUTPUT | MUX_MODE0) /* uart5_cts.uart5_rts */
283 >;
284 };
285
286 dss_hdmi_pins: dss-hdmi-pins {
287 pinctrl-single,pins = <
288 OMAP5_IOPAD(0x13c, PIN_INPUT | MUX_MODE0) /* hdmi_cec.hdmi_cec */
289 OMAP5_IOPAD(0x140, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_scl.hdmi_ddc_scl */
290 OMAP5_IOPAD(0x142, PIN_INPUT | MUX_MODE0) /* hdmi_ddc_sda.hdmi_ddc_sda */
291 >;
292 };
293
294 tpd12s015_pins: tpd12s015-pins {
295 pinctrl-single,pins = <
296 OMAP5_IOPAD(0x13e, PIN_INPUT_PULLDOWN | MUX_MODE6) /* hdmi_hpd.gpio7_193 */
297 >;
298 };
299 };
300
301 &omap5_pmx_wkup {
302 pinctrl-names = "default";
303 pinctrl-0 = <
304 &usbhost_wkup_pins
305 >;
306
307 palmas_sys_nirq_pins: palmas-sys-nirq-pins {
308 pinctrl-single,pins = <
309 /* sys_nirq1 is pulled down as the SoC is inverting it for GIC */
310 OMAP5_IOPAD(0x068, PIN_INPUT_PULLUP | MUX_MODE0)
311 >;
312 };
313
314 usbhost_wkup_pins: usbhost-wkup-pins {
315 pinctrl-single,pins = <
316 OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
317 >;
318 };
319
320 wlcore_irq_pin: wlcore-irq-pin-pins {
321 pinctrl-single,pins = <
322 OMAP5_IOPAD(0x40, PIN_INPUT | MUX_MODE6) /* llia_wakereqin.gpio1_wk14 */
323 >;
324 };
325 };
326
327 &mmc1 {
328 vmmc-supply = <&ldo9_reg>;
329 bus-width = <4>;
330 };
331
332 &mmc2 {
333 vmmc-supply = <&vmmcsd_fixed>;
334 bus-width = <8>;
335 ti,non-removable;
336 };
337
338 &mmc3 {
339 vmmc-supply = <&vmmcsdio_fixed>;
340 mmc-pwrseq = <&mmc3_pwrseq>;
341 bus-width = <4>;
342 non-removable;
343 cap-power-off-card;
344 pinctrl-names = "default";
345 pinctrl-0 = <&mmc3_pins>;
346 interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
347 &omap5_pmx_core 0x16a>;
348
349 #address-cells = <1>;
350 #size-cells = <0>;
351 wlcore: wlcore@2 {
352 compatible = "ti,wl1271";
353 reg = <2>;
354 pinctrl-names = "default";
355 pinctrl-0 = <&wlcore_irq_pin>;
356 interrupt-parent = <&gpio1>;
357 interrupts = <14 IRQ_TYPE_LEVEL_HIGH>; /* gpio 14 */
358 ref-clock-frequency = <26000000>;
359 };
360 };
361
362 &mmc4 {
363 status = "disabled";
364 };
365
366 &mmc5 {
367 status = "disabled";
368 };
369
370 &i2c1 {
371 pinctrl-names = "default";
372 pinctrl-0 = <&i2c1_pins>;
373
374 clock-frequency = <400000>;
375
376 palmas: palmas@48 {
377 compatible = "ti,palmas";
378 /* sys_nirq/ext_sys_irq pins get inverted at mpuss wakeupgen */
379 interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_LOW>;
380 reg = <0x48>;
381 interrupt-controller;
382 #interrupt-cells = <2>;
383 ti,system-power-controller;
384 ti,mux-pad1 = <0xa1>;
385 ti,mux-pad2 = <0x1b>;
386 pinctrl-names = "default";
387 pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>;
388
389 palmas_gpio: gpio {
390 compatible = "ti,palmas-gpio";
391 gpio-controller;
392 #gpio-cells = <2>;
393 };
394
395 extcon_usb3: palmas_usb {
396 compatible = "ti,palmas-usb-vid";
397 ti,enable-vbus-detection;
398 ti,enable-id-detection;
399 ti,wakeup;
400 id-gpios = <&palmas_gpio 0 GPIO_ACTIVE_HIGH>;
401 };
402
403 clk32kgaudio: palmas_clk32k@1 {
404 compatible = "ti,palmas-clk32kgaudio";
405 #clock-cells = <0>;
406 };
407
408 rtc {
409 compatible = "ti,palmas-rtc";
410 interrupt-parent = <&palmas>;
411 interrupts = <8 IRQ_TYPE_NONE>;
412 ti,backup-battery-chargeable;
413 ti,backup-battery-charge-high-current;
414 };
415
416 gpadc: gpadc {
417 compatible = "ti,palmas-gpadc";
418 interrupts = <18 0>,
419 <16 0>,
420 <17 0>;
421 #io-channel-cells = <1>;
422 ti,channel0-current-microamp = <5>;
423 ti,channel3-current-microamp = <10>;
424 };
425
426 palmas_pmic {
427 compatible = "ti,palmas-pmic";
428 interrupt-parent = <&palmas>;
429 interrupts = <14 IRQ_TYPE_NONE>;
430 interrupt-names = "short-irq";
431
432 ti,ldo6-vibrator;
433
434 smps123-in-supply = <&vsys_cobra>;
435 smps45-in-supply = <&vsys_cobra>;
436 smps6-in-supply = <&vsys_cobra>;
437 smps7-in-supply = <&vsys_cobra>;
438 smps8-in-supply = <&vsys_cobra>;
439 smps9-in-supply = <&vsys_cobra>;
440 smps10_out2-in-supply = <&vsys_cobra>;
441 smps10_out1-in-supply = <&vsys_cobra>;
442 ldo1-in-supply = <&vsys_cobra>;
443 ldo2-in-supply = <&vsys_cobra>;
444 ldo3-in-supply = <&vdds_1v8_main>;
445 ldo4-in-supply = <&vdds_1v8_main>;
446 ldo5-in-supply = <&vsys_cobra>;
447 ldo6-in-supply = <&vdds_1v8_main>;
448 ldo7-in-supply = <&vsys_cobra>;
449 ldo8-in-supply = <&vsys_cobra>;
450 ldo9-in-supply = <&vmmcsd_fixed>;
451 ldoln-in-supply = <&vsys_cobra>;
452 ldousb-in-supply = <&vsys_cobra>;
453
454 regulators {
455 smps123_reg: smps123 {
456 /* VDD_OPP_MPU */
457 regulator-name = "smps123";
458 regulator-min-microvolt = < 600000>;
459 regulator-max-microvolt = <1500000>;
460 regulator-always-on;
461 regulator-boot-on;
462 };
463
464 smps45_reg: smps45 {
465 /* VDD_OPP_MM */
466 regulator-name = "smps45";
467 regulator-min-microvolt = < 600000>;
468 regulator-max-microvolt = <1310000>;
469 regulator-always-on;
470 regulator-boot-on;
471 };
472
473 smps6_reg: smps6 {
474 /* VDD_DDR3 - over VDD_SMPS6 */
475 regulator-name = "smps6";
476 regulator-min-microvolt = <1350000>;
477 regulator-max-microvolt = <1350000>;
478 regulator-always-on;
479 regulator-boot-on;
480 };
481
482 vdds_1v8_main:
483 smps7_reg: smps7 {
484 /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */
485 regulator-name = "smps7";
486 regulator-min-microvolt = <1800000>;
487 regulator-max-microvolt = <1800000>;
488 regulator-always-on;
489 regulator-boot-on;
490 };
491
492 smps8_reg: smps8 {
493 /* VDD_OPP_CORE */
494 regulator-name = "smps8";
495 regulator-min-microvolt = < 600000>;
496 regulator-max-microvolt = <1310000>;
497 regulator-always-on;
498 regulator-boot-on;
499 };
500
501 smps9_reg: smps9 {
502 /* VDDA_2v1_AUD over VDD_2v1 */
503 regulator-name = "smps9";
504 regulator-min-microvolt = <2100000>;
505 regulator-max-microvolt = <2100000>;
506 ti,smps-range = <0x80>;
507 };
508
509 smps10_out2_reg: smps10_out2 {
510 /* VBUS_5V_OTG */
511 regulator-name = "smps10_out2";
512 regulator-min-microvolt = <5000000>;
513 regulator-max-microvolt = <5000000>;
514 regulator-always-on;
515 regulator-boot-on;
516 };
517
518 smps10_out1_reg: smps10_out1 {
519 /* VBUS_5V_OTG */
520 regulator-name = "smps10_out1";
521 regulator-min-microvolt = <5000000>;
522 regulator-max-microvolt = <5000000>;
523 };
524
525 ldo1_reg: ldo1 {
526 /* VDDAPHY_CAM: vdda_csiport */
527 regulator-name = "ldo1";
528 regulator-min-microvolt = <1800000>;
529 regulator-max-microvolt = <1800000>;
530 };
531
532 ldo2_reg: ldo2 {
533 /* VCC_2V8_DISP: Does not go anywhere */
534 regulator-name = "ldo2";
535 regulator-min-microvolt = <2800000>;
536 regulator-max-microvolt = <2800000>;
537 /* Unused */
538 status = "disabled";
539 };
540
541 ldo3_reg: ldo3 {
542 /* VDDAPHY_MDM: vdda_lli */
543 regulator-name = "ldo3";
544 regulator-min-microvolt = <1500000>;
545 regulator-max-microvolt = <1500000>;
546 regulator-boot-on;
547 /* Only if Modem is used */
548 status = "disabled";
549 };
550
551 ldo4_reg: ldo4 {
552 /* VDDAPHY_DISP: vdda_dsiport/hdmi */
553 regulator-name = "ldo4";
554 regulator-min-microvolt = <1800000>;
555 regulator-max-microvolt = <1800000>;
556 };
557
558 ldo5_reg: ldo5 {
559 /* VDDA_1V8_PHY: usb/sata/hdmi.. */
560 regulator-name = "ldo5";
561 regulator-min-microvolt = <1800000>;
562 regulator-max-microvolt = <1800000>;
563 regulator-always-on;
564 regulator-boot-on;
565 };
566
567 ldo6_reg: ldo6 {
568 /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */
569 regulator-name = "ldo6";
570 regulator-min-microvolt = <1200000>;
571 regulator-max-microvolt = <1200000>;
572 regulator-always-on;
573 regulator-boot-on;
574 };
575
576 ldo7_reg: ldo7 {
577 /* VDD_VPP: vpp1 */
578 regulator-name = "ldo7";
579 regulator-min-microvolt = <2000000>;
580 regulator-max-microvolt = <2000000>;
581 /* Only for efuse reprograming! */
582 status = "disabled";
583 };
584
585 ldo8_reg: ldo8 {
586 /* VDD_3v0: Does not go anywhere */
587 regulator-name = "ldo8";
588 regulator-min-microvolt = <3000000>;
589 regulator-max-microvolt = <3000000>;
590 regulator-boot-on;
591 /* Unused */
592 status = "disabled";
593 };
594
595 ldo9_reg: ldo9 {
596 /* VCC_DV_SDIO: vdds_sdcard */
597 regulator-name = "ldo9";
598 regulator-min-microvolt = <1800000>;
599 regulator-max-microvolt = <3000000>;
600 regulator-boot-on;
601 };
602
603 ldoln_reg: ldoln {
604 /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */
605 regulator-name = "ldoln";
606 regulator-min-microvolt = <1800000>;
607 regulator-max-microvolt = <1800000>;
608 regulator-always-on;
609 regulator-boot-on;
610 };
611
612 ldousb_reg: ldousb {
613 /* VDDA_3V_USB: VDDA_USBHS33 */
614 regulator-name = "ldousb";
615 regulator-min-microvolt = <3250000>;
616 regulator-max-microvolt = <3250000>;
617 regulator-always-on;
618 regulator-boot-on;
619 };
620
621 regen3_reg: regen3 {
622 /* REGEN3 controls LDO9 supply to card */
623 regulator-name = "regen3";
624 regulator-always-on;
625 regulator-boot-on;
626 };
627 };
628 };
629
630 palmas_power_button: palmas_power_button {
631 compatible = "ti,palmas-pwrbutton";
632 interrupt-parent = <&palmas>;
633 interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
634 wakeup-source;
635 };
636 };
637
638 twl6040: twl@4b {
639 compatible = "ti,twl6040";
640 #clock-cells = <0>;
641 reg = <0x4b>;
642
643 pinctrl-names = "default";
644 pinctrl-0 = <&twl6040_pins>;
645
646 /* sys_nirq/ext_sys_irq pins get inverted at mpuss wakeupgen */
647 interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_LOW>;
648
649 /* audpwron gpio defined in the board specific dts */
650
651 vio-supply = <&smps7_reg>;
652 v2v1-supply = <&smps9_reg>;
653 enable-active-high;
654
655 clocks = <&clk32kgaudio>, <&fref_xtal_ck>;
656 clock-names = "clk32k", "mclk";
657 };
658 };
659
660 &mcpdm_module {
661 /* Module on the SoC needs external clock from the PMIC */
662 pinctrl-names = "default";
663 pinctrl-0 = <&mcpdm_pins>;
664 status = "okay";
665 };
666
667 &mcpdm {
668 clocks = <&twl6040>;
669 clock-names = "pdmclk";
670 };
671
672 &mcbsp1 {
673 pinctrl-names = "default";
674 pinctrl-0 = <&mcbsp1_pins>;
675 status = "okay";
676 };
677
678 &mcbsp2 {
679 pinctrl-names = "default";
680 pinctrl-0 = <&mcbsp2_pins>;
681 status = "okay";
682 };
683
684 &usbhshost {
685 port2-mode = "ehci-hsic";
686 port3-mode = "ehci-hsic";
687 };
688
689 &usbhsehci {
690 phys = <0 &hsusb2_phy &hsusb3_phy>;
691 };
692
693 &usb3 {
694 extcon = <&extcon_usb3>;
695 vbus-supply = <&smps10_out1_reg>;
696 };
697
698 &dwc3 {
699 extcon = <&extcon_usb3>;
700 dr_mode = "otg";
701 };
702
703 &mcspi1 {
704
705 };
706
707 &mcspi2 {
708 pinctrl-names = "default";
709 pinctrl-0 = <&mcspi2_pins>;
710 };
711
712 &mcspi3 {
713 pinctrl-names = "default";
714 pinctrl-0 = <&mcspi3_pins>;
715 };
716
717 &uart1 {
718 pinctrl-names = "default";
719 pinctrl-0 = <&uart1_pins>;
720 };
721
722 &uart3 {
723 pinctrl-names = "default";
724 pinctrl-0 = <&uart3_pins>;
725 interrupts-extended = <&wakeupgen GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
726 <&omap5_pmx_core 0x19c>;
727 };
728
729 &uart5 {
730 pinctrl-names = "default";
731 pinctrl-0 = <&uart5_pins>;
732 };
733
734 &cpu0 {
735 cpu0-supply = <&smps123_reg>;
736 };
737
738 &dss {
739 status = "okay";
740 };
741
742 &hdmi {
743 status = "okay";
744
745 /* vdda-supply populated in board specific dts file */
746
747 pinctrl-names = "default";
748 pinctrl-0 = <&dss_hdmi_pins>;
749
750 port {
751 hdmi_out: endpoint {
752 remote-endpoint = <&tpd12s015_in>;
753 };
754 };
755 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.