1 // SPDX-License-Identifier: GPL-2.0
2 /* Copyright (c) 2016, The Linux Foundation. All rights reserved. */
3
4 /dts-v1/;
5
6 #include "msm8998.dtsi"
7 #include "pm8005.dtsi"
8 #include "pm8998.dtsi"
9 #include "pmi8998.dtsi"
10
11 / {
12 model = "Qualcomm Technologies, Inc. MSM8998 v1 MTP";
13 compatible = "qcom,msm8998-mtp", "qcom,msm8998";
14 chassis-type = "handset";
15
16 qcom,board-id = <8 0>;
17
18 aliases {
19 serial0 = &blsp2_uart1;
20 serial1 = &blsp1_uart3;
21 };
22
23 chosen {
24 stdout-path = "serial0:115200n8";
25 };
26
27 vph_pwr: vph-pwr-regulator {
28 compatible = "regulator-fixed";
29 regulator-name = "vph_pwr";
30 regulator-always-on;
31 regulator-boot-on;
32 };
33 };
34
35 &blsp1_uart3 {
36 status = "okay";
37
38 bluetooth {
39 compatible = "qcom,wcn3990-bt";
40
41 vddio-supply = <&vreg_s4a_1p8>;
42 vddxo-supply = <&vreg_l7a_1p8>;
43 vddrf-supply = <&vreg_l17a_1p3>;
44 vddch0-supply = <&vreg_l25a_3p3>;
45 max-speed = <3200000>;
46 };
47 };
48
49 &blsp1_uart3_on {
50 rx-pins {
51 /delete-property/ bias-disable;
52 /*
53 * Configure a pull-up on 45 (RX). This is needed to
54 * avoid garbage data when the TX pin of the Bluetooth
55 * module is in tri-state (module powered off or not
56 * driving the signal yet).
57 */
58 bias-pull-up;
59 };
60
61 cts-pins {
62 /delete-property/ bias-disable;
63 /*
64 * Configure a pull-down on 47 (CTS) to match the pull
65 * of the Bluetooth module.
66 */
67 bias-pull-down;
68 };
69 };
70
71 &blsp2_uart1 {
72 status = "okay";
73 };
74
75 &etf {
76 status = "okay";
77 };
78
79 &etm1 {
80 status = "okay";
81 };
82
83 &etm2 {
84 status = "okay";
85 };
86
87 &etm3 {
88 status = "okay";
89 };
90
91 &etm4 {
92 status = "okay";
93 };
94
95 &etm5 {
96 status = "okay";
97 };
98
99 &etm6 {
100 status = "okay";
101 };
102
103 &etm7 {
104 status = "okay";
105 };
106
107 &etm8 {
108 status = "okay";
109 };
110
111 &etr {
112 status = "okay";
113 };
114
115 &funnel1 {
116 status = "okay";
117 };
118
119 &funnel2 {
120 status = "okay";
121 };
122
123 &funnel3 {
124 status = "okay";
125 };
126
127 &funnel4 {
128 /* FIXME: Figure out why clock late_initcall crashes the board with this enabled. */
129 };
130
131 &funnel5 {
132 /* FIXME: Figure out why clock late_initcall crashes the board with this enabled. */
133 };
134
135 &pcie0 {
136 status = "okay";
137 };
138
139 &pcie_phy {
140 status = "okay";
141 };
142
143 &pm8005_regulators {
144 vdd_s1-supply = <&vph_pwr>;
145
146 pm8005_s1: s1 { /* VDD_GFX supply */
147 regulator-min-microvolt = <524000>;
148 regulator-max-microvolt = <1100000>;
149 regulator-enable-ramp-delay = <500>;
150
151 /* Hack until we rig up the gpu consumer */
152 regulator-always-on;
153 };
154 };
155
156 &qusb2phy {
157 status = "okay";
158
159 vdda-pll-supply = <&vreg_l12a_1p8>;
160 vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
161 };
162
163 &replicator1 {
164 status = "okay";
165 };
166
167 &rpm_requests {
168 regulators-0 {
169 compatible = "qcom,rpm-pm8998-regulators";
170
171 vdd_s1-supply = <&vph_pwr>;
172 vdd_s2-supply = <&vph_pwr>;
173 vdd_s3-supply = <&vph_pwr>;
174 vdd_s4-supply = <&vph_pwr>;
175 vdd_s5-supply = <&vph_pwr>;
176 vdd_s6-supply = <&vph_pwr>;
177 vdd_s7-supply = <&vph_pwr>;
178 vdd_s8-supply = <&vph_pwr>;
179 vdd_s9-supply = <&vph_pwr>;
180 vdd_s10-supply = <&vph_pwr>;
181 vdd_s11-supply = <&vph_pwr>;
182 vdd_s12-supply = <&vph_pwr>;
183 vdd_s13-supply = <&vph_pwr>;
184 vdd_l1_l27-supply = <&vreg_s7a_1p025>;
185 vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
186 vdd_l3_l11-supply = <&vreg_s7a_1p025>;
187 vdd_l4_l5-supply = <&vreg_s7a_1p025>;
188 vdd_l6-supply = <&vreg_s5a_2p04>;
189 vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
190 vdd_l9-supply = <&vreg_bob>;
191 vdd_l10_l23_l25-supply = <&vreg_bob>;
192 vdd_l13_l19_l21-supply = <&vreg_bob>;
193 vdd_l16_l28-supply = <&vreg_bob>;
194 vdd_l18_l22-supply = <&vreg_bob>;
195 vdd_l20_l24-supply = <&vreg_bob>;
196 vdd_l26-supply = <&vreg_s3a_1p35>;
197 vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
198
199 vreg_s3a_1p35: s3 {
200 regulator-min-microvolt = <1352000>;
201 regulator-max-microvolt = <1352000>;
202 };
203
204 vreg_s4a_1p8: s4 {
205 regulator-min-microvolt = <1800000>;
206 regulator-max-microvolt = <1800000>;
207 regulator-allow-set-load;
208 };
209
210 vreg_s5a_2p04: s5 {
211 regulator-min-microvolt = <1904000>;
212 regulator-max-microvolt = <2040000>;
213 };
214
215 vreg_s7a_1p025: s7 {
216 regulator-min-microvolt = <900000>;
217 regulator-max-microvolt = <1028000>;
218 };
219
220 vreg_l1a_0p875: l1 {
221 regulator-min-microvolt = <880000>;
222 regulator-max-microvolt = <880000>;
223 };
224
225 vreg_l2a_1p2: l2 {
226 regulator-min-microvolt = <1200000>;
227 regulator-max-microvolt = <1200000>;
228 };
229
230 vreg_l3a_1p0: l3 {
231 regulator-min-microvolt = <1000000>;
232 regulator-max-microvolt = <1000000>;
233 };
234
235 vreg_l5a_0p8: l5 {
236 regulator-min-microvolt = <800000>;
237 regulator-max-microvolt = <800000>;
238 };
239
240 vreg_l6a_1p8: l6 {
241 regulator-min-microvolt = <1808000>;
242 regulator-max-microvolt = <1808000>;
243 };
244
245 vreg_l7a_1p8: l7 {
246 regulator-min-microvolt = <1800000>;
247 regulator-max-microvolt = <1800000>;
248 };
249
250 vreg_l8a_1p2: l8 {
251 regulator-min-microvolt = <1200000>;
252 regulator-max-microvolt = <1200000>;
253 };
254
255 vreg_l9a_1p8: l9 {
256 regulator-min-microvolt = <1808000>;
257 regulator-max-microvolt = <2960000>;
258 };
259
260 vreg_l10a_1p8: l10 {
261 regulator-min-microvolt = <1808000>;
262 regulator-max-microvolt = <2960000>;
263 };
264
265 vreg_l11a_1p0: l11 {
266 regulator-min-microvolt = <1000000>;
267 regulator-max-microvolt = <1000000>;
268 };
269
270 vreg_l12a_1p8: l12 {
271 regulator-min-microvolt = <1800000>;
272 regulator-max-microvolt = <1800000>;
273 };
274
275 vreg_l13a_2p95: l13 {
276 regulator-min-microvolt = <1808000>;
277 regulator-max-microvolt = <2960000>;
278 };
279
280 vreg_l14a_1p88: l14 {
281 regulator-min-microvolt = <1880000>;
282 regulator-max-microvolt = <1880000>;
283 };
284
285 vreg_l15a_1p8: l15 {
286 regulator-min-microvolt = <1800000>;
287 regulator-max-microvolt = <1800000>;
288 };
289
290 vreg_l16a_2p7: l16 {
291 regulator-min-microvolt = <2704000>;
292 regulator-max-microvolt = <2704000>;
293 };
294
295 vreg_l17a_1p3: l17 {
296 regulator-min-microvolt = <1304000>;
297 regulator-max-microvolt = <1304000>;
298 };
299
300 vreg_l18a_2p7: l18 {
301 regulator-min-microvolt = <2704000>;
302 regulator-max-microvolt = <2704000>;
303 };
304
305 vreg_l19a_3p0: l19 {
306 regulator-min-microvolt = <3008000>;
307 regulator-max-microvolt = <3008000>;
308 };
309
310 vreg_l20a_2p95: l20 {
311 regulator-min-microvolt = <2960000>;
312 regulator-max-microvolt = <2960000>;
313 regulator-allow-set-load;
314 };
315
316 vreg_l21a_2p95: l21 {
317 regulator-min-microvolt = <2960000>;
318 regulator-max-microvolt = <2960000>;
319 regulator-system-load = <800000>;
320 regulator-allow-set-load;
321 };
322
323 vreg_l22a_2p85: l22 {
324 regulator-min-microvolt = <2864000>;
325 regulator-max-microvolt = <2864000>;
326 };
327
328 vreg_l23a_3p3: l23 {
329 regulator-min-microvolt = <3312000>;
330 regulator-max-microvolt = <3312000>;
331 };
332
333 vreg_l24a_3p075: l24 {
334 regulator-min-microvolt = <3088000>;
335 regulator-max-microvolt = <3088000>;
336 };
337
338 vreg_l25a_3p3: l25 {
339 regulator-min-microvolt = <3104000>;
340 regulator-max-microvolt = <3312000>;
341 };
342
343 vreg_l26a_1p2: l26 {
344 regulator-min-microvolt = <1200000>;
345 regulator-max-microvolt = <1200000>;
346 regulator-allow-set-load;
347 };
348
349 vreg_l28_3p0: l28 {
350 regulator-min-microvolt = <3008000>;
351 regulator-max-microvolt = <3008000>;
352 };
353
354 vreg_lvs1a_1p8: lvs1 {
355 regulator-min-microvolt = <1800000>;
356 regulator-max-microvolt = <1800000>;
357 };
358
359 vreg_lvs2a_1p8: lvs2 {
360 regulator-min-microvolt = <1800000>;
361 regulator-max-microvolt = <1800000>;
362 };
363
364 };
365
366 regulators-1 {
367 compatible = "qcom,rpm-pmi8998-regulators";
368
369 vdd_bob-supply = <&vph_pwr>;
370
371 vreg_bob: bob {
372 regulator-min-microvolt = <3312000>;
373 regulator-max-microvolt = <3600000>;
374 };
375 };
376 };
377
378 &remoteproc_adsp {
379 status = "okay";
380 };
381
382 &remoteproc_mss {
383 status = "okay";
384 };
385
386 &remoteproc_slpi {
387 status = "okay";
388 };
389
390 &tlmm {
391 gpio-reserved-ranges = <0 4>, <81 4>;
392 };
393
394 &sdhc2 {
395 status = "okay";
396 cd-gpios = <&tlmm 95 GPIO_ACTIVE_LOW>;
397
398 vmmc-supply = <&vreg_l21a_2p95>;
399 vqmmc-supply = <&vreg_l13a_2p95>;
400
401 pinctrl-names = "default", "sleep";
402 pinctrl-0 = <&sdc2_on &sdc2_cd>;
403 pinctrl-1 = <&sdc2_off &sdc2_cd>;
404 };
405
406 &stm {
407 status = "okay";
408 };
409
410 &ufshc {
411 status = "okay";
412 vcc-supply = <&vreg_l20a_2p95>;
413 vccq-supply = <&vreg_l26a_1p2>;
414 vccq2-supply = <&vreg_s4a_1p8>;
415 vdd-hba-supply = <&vreg_l26a_1p2>;
416 vcc-max-microamp = <750000>;
417 vccq-max-microamp = <560000>;
418 vccq2-max-microamp = <750000>;
419 };
420
421 &ufsphy {
422 status = "okay";
423 vdda-phy-supply = <&vreg_l1a_0p875>;
424 vdda-pll-supply = <&vreg_l2a_1p2>;
425 };
426
427 &usb3 {
428 status = "okay";
429 };
430
431 &usb3_dwc3 {
432 dr_mode = "host"; /* Force to host until we have Type-C hooked up */
433 };
434
435 &usb3phy {
436 status = "okay";
437
438 vdda-phy-supply = <&vreg_l1a_0p875>;
439 vdda-pll-supply = <&vreg_l2a_1p2>;
440 };
441
442 &wifi {
443 status = "okay";
444
445 vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
446 vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
447 vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
448 vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
449 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.