1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * SDM845 OnePlus 6(T) (enchilada / fajita) common device tree source
4 *
5 * Copyright (c) 2020, The Linux Foundation. All rights reserved.
6 */
7
8 /dts-v1/;
9
10 #include <dt-bindings/input/linux-event-codes.h>
11 #include <dt-bindings/leds/common.h>
12 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
13 #include <dt-bindings/sound/qcom,q6afe.h>
14 #include <dt-bindings/sound/qcom,q6asm.h>
15
16 #include "sdm845.dtsi"
17 #include "sdm845-wcd9340.dtsi"
18 #include "pm8998.dtsi"
19 #include "pmi8998.dtsi"
20
21 /delete-node/ &rmtfs_mem;
22
23 / {
24 aliases {
25 serial0 = &uart9;
26 serial1 = &uart6;
27 };
28
29 chosen {
30 stdout-path = "serial0:115200n8";
31 };
32
33 gpio-hall-sensor {
34 compatible = "gpio-keys";
35 label = "Hall effect sensor";
36
37 pinctrl-0 = <&hall_sensor_default>;
38 pinctrl-names = "default";
39
40 event-hall-sensor {
41 gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
42 label = "Hall Effect Sensor";
43 linux,input-type = <EV_SW>;
44 linux,code = <SW_LID>;
45 linux,can-disable;
46 wakeup-source;
47 };
48 };
49
50 gpio-keys {
51 compatible = "gpio-keys";
52 label = "Volume keys";
53 autorepeat;
54
55 pinctrl-names = "default";
56 pinctrl-0 = <&volume_down_gpio &volume_up_gpio>;
57
58 key-vol-down {
59 label = "Volume down";
60 linux,code = <KEY_VOLUMEDOWN>;
61 gpios = <&pm8998_gpios 5 GPIO_ACTIVE_LOW>;
62 debounce-interval = <15>;
63 };
64
65 key-vol-up {
66 label = "Volume up";
67 linux,code = <KEY_VOLUMEUP>;
68 gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>;
69 debounce-interval = <15>;
70 };
71 };
72
73 reserved-memory {
74 /*
75 * The rmtfs_mem needs to be guarded due to "XPU limitations"
76 * it is otherwise possible for an allocation adjacent to the
77 * rmtfs_mem region to trigger an XPU violation, causing a crash.
78 */
79 rmtfs_lower_guard: rmtfs-lower-guard@f5b00000 {
80 no-map;
81 reg = <0 0xf5b00000 0 0x1000>;
82 };
83 /*
84 * The rmtfs memory region in downstream is 'dynamically allocated'
85 * but given the same address every time. Hard code it as this address is
86 * where the modem firmware expects it to be.
87 */
88 rmtfs_mem: rmtfs-mem@f5b01000 {
89 compatible = "qcom,rmtfs-mem";
90 reg = <0 0xf5b01000 0 0x200000>;
91 no-map;
92
93 qcom,client-id = <1>;
94 qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
95 };
96 rmtfs_upper_guard: rmtfs-upper-guard@f5d01000 {
97 no-map;
98 reg = <0 0xf5d01000 0 0x1000>;
99 };
100
101 /*
102 * It seems like reserving the old rmtfs_mem region is also needed to prevent
103 * random crashes which are most likely modem related, more testing needed.
104 */
105 removed_region: removed-region@88f00000 {
106 no-map;
107 reg = <0 0x88f00000 0 0x1c00000>;
108 };
109
110 ramoops: ramoops@ac300000 {
111 compatible = "ramoops";
112 reg = <0 0xac300000 0 0x400000>;
113 record-size = <0x40000>;
114 console-size = <0x40000>;
115 ftrace-size = <0x40000>;
116 pmsg-size = <0x200000>;
117 ecc-size = <16>;
118 };
119 };
120
121 vph_pwr: vph-pwr-regulator {
122 compatible = "regulator-fixed";
123 regulator-name = "vph_pwr";
124 regulator-min-microvolt = <3700000>;
125 regulator-max-microvolt = <3700000>;
126 };
127
128 /*
129 * Apparently RPMh does not provide support for PM8998 S4 because it
130 * is always-on; model it as a fixed regulator.
131 */
132 vreg_s4a_1p8: pm8998-smps4 {
133 compatible = "regulator-fixed";
134 regulator-name = "vreg_s4a_1p8";
135
136 regulator-min-microvolt = <1800000>;
137 regulator-max-microvolt = <1800000>;
138
139 regulator-always-on;
140 regulator-boot-on;
141
142 vin-supply = <&vph_pwr>;
143 };
144
145 /*
146 * The touchscreen regulator seems to be controlled somehow by a gpio.
147 * Model it as a fixed regulator and keep it on. Without schematics we
148 * don't know how this is actually wired up...
149 */
150 ts_1p8_supply: ts-1p8-regulator {
151 compatible = "regulator-fixed";
152 regulator-name = "ts_1p8_supply";
153
154 regulator-min-microvolt = <1800000>;
155 regulator-max-microvolt = <1800000>;
156
157 gpio = <&tlmm 88 0>;
158 enable-active-high;
159 regulator-boot-on;
160 };
161 };
162
163 &adsp_pas {
164 status = "okay";
165 firmware-name = "qcom/sdm845/oneplus6/adsp.mbn";
166 };
167
168 &apps_rsc {
169 regulators-0 {
170 compatible = "qcom,pm8998-rpmh-regulators";
171 qcom,pmic-id = "a";
172
173 vdd-s1-supply = <&vph_pwr>;
174 vdd-s2-supply = <&vph_pwr>;
175 vdd-s3-supply = <&vph_pwr>;
176 vdd-s4-supply = <&vph_pwr>;
177 vdd-s5-supply = <&vph_pwr>;
178 vdd-s6-supply = <&vph_pwr>;
179 vdd-s7-supply = <&vph_pwr>;
180 vdd-s8-supply = <&vph_pwr>;
181 vdd-s9-supply = <&vph_pwr>;
182 vdd-s10-supply = <&vph_pwr>;
183 vdd-s11-supply = <&vph_pwr>;
184 vdd-s12-supply = <&vph_pwr>;
185 vdd-s13-supply = <&vph_pwr>;
186 vdd-l1-l27-supply = <&vreg_s7a_1p025>;
187 vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
188 vdd-l3-l11-supply = <&vreg_s7a_1p025>;
189 vdd-l4-l5-supply = <&vreg_s7a_1p025>;
190 vdd-l6-supply = <&vph_pwr>;
191 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
192 vdd-l9-supply = <&vreg_bob>;
193 vdd-l10-l23-l25-supply = <&vreg_bob>;
194 vdd-l13-l19-l21-supply = <&vreg_bob>;
195 vdd-l16-l28-supply = <&vreg_bob>;
196 vdd-l18-l22-supply = <&vreg_bob>;
197 vdd-l20-l24-supply = <&vreg_bob>;
198 vdd-l26-supply = <&vreg_s3a_1p35>;
199 vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
200
201 vreg_s3a_1p35: smps3 {
202 regulator-min-microvolt = <1352000>;
203 regulator-max-microvolt = <1352000>;
204 };
205
206 vreg_s5a_2p04: smps5 {
207 regulator-min-microvolt = <1904000>;
208 regulator-max-microvolt = <2040000>;
209 };
210
211 vreg_s7a_1p025: smps7 {
212 regulator-min-microvolt = <900000>;
213 regulator-max-microvolt = <1028000>;
214 };
215
216 vdda_mipi_dsi0_pll:
217 vdda_qlink_lv:
218 vdda_ufs1_core:
219 vdda_usb1_ss_core:
220 vreg_l1a_0p875: ldo1 {
221 regulator-min-microvolt = <880000>;
222 regulator-max-microvolt = <880000>;
223 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
224 };
225
226 vreg_l2a_1p2: ldo2 {
227 regulator-min-microvolt = <1200000>;
228 regulator-max-microvolt = <1200000>;
229 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
230 regulator-always-on;
231 };
232
233 vreg_l5a_0p8: ldo5 {
234 regulator-min-microvolt = <800000>;
235 regulator-max-microvolt = <800000>;
236 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
237 };
238
239 vreg_l7a_1p8: ldo7 {
240 regulator-min-microvolt = <1800000>;
241 regulator-max-microvolt = <1800000>;
242 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
243 };
244
245 vdda_qusb_hs0_1p8:
246 vreg_l12a_1p8: ldo12 {
247 regulator-min-microvolt = <1800000>;
248 regulator-max-microvolt = <1800000>;
249 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
250 };
251
252 vreg_l14a_1p88: ldo14 {
253 regulator-min-microvolt = <1800000>;
254 regulator-max-microvolt = <1800000>;
255 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
256 regulator-always-on;
257 };
258
259 vreg_l17a_1p3: ldo17 {
260 regulator-min-microvolt = <1304000>;
261 regulator-max-microvolt = <1304000>;
262 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
263 };
264
265 vreg_l20a_2p95: ldo20 {
266 regulator-min-microvolt = <2704000>;
267 regulator-max-microvolt = <2960000>;
268 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
269 };
270
271 vreg_l23a_3p3: ldo23 {
272 regulator-min-microvolt = <3300000>;
273 regulator-max-microvolt = <3312000>;
274 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
275 };
276
277 vdda_qusb_hs0_3p1:
278 vreg_l24a_3p075: ldo24 {
279 regulator-min-microvolt = <3088000>;
280 regulator-max-microvolt = <3088000>;
281 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
282 };
283
284 vreg_l25a_3p3: ldo25 {
285 regulator-min-microvolt = <3300000>;
286 regulator-max-microvolt = <3312000>;
287 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
288 };
289
290 vdda_mipi_dsi0_1p2:
291 vdda_ufs1_1p2:
292 vreg_l26a_1p2: ldo26 {
293 regulator-min-microvolt = <1200000>;
294 regulator-max-microvolt = <1200000>;
295 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
296 };
297
298 vreg_l28a_3p0: ldo28 {
299 regulator-min-microvolt = <2856000>;
300 regulator-max-microvolt = <3008000>;
301 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
302 };
303 };
304
305 regulators-1 {
306 compatible = "qcom,pmi8998-rpmh-regulators";
307 qcom,pmic-id = "b";
308
309 vdd-bob-supply = <&vph_pwr>;
310
311 vreg_bob: bob {
312 regulator-min-microvolt = <3312000>;
313 regulator-max-microvolt = <3600000>;
314 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
315 regulator-allow-bypass;
316 };
317 };
318
319 regulators-2 {
320 compatible = "qcom,pm8005-rpmh-regulators";
321 qcom,pmic-id = "c";
322
323 vdd-s1-supply = <&vph_pwr>;
324 vdd-s2-supply = <&vph_pwr>;
325 vdd-s3-supply = <&vph_pwr>;
326 vdd-s4-supply = <&vph_pwr>;
327
328 vreg_s3c_0p6: smps3 {
329 regulator-min-microvolt = <600000>;
330 regulator-max-microvolt = <600000>;
331 };
332 };
333 };
334
335 &cdsp_pas {
336 status = "okay";
337 firmware-name = "qcom/sdm845/oneplus6/cdsp.mbn";
338 };
339
340 &gcc {
341 protected-clocks = <GCC_QSPI_CORE_CLK>,
342 <GCC_QSPI_CORE_CLK_SRC>,
343 <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
344 <GCC_LPASS_Q6_AXI_CLK>,
345 <GCC_LPASS_SWAY_CLK>;
346 };
347
348 &gmu {
349 status = "okay";
350 };
351
352 &gpu {
353 status = "okay";
354
355 zap-shader {
356 memory-region = <&gpu_mem>;
357 firmware-name = "qcom/sdm845/oneplus6/a630_zap.mbn";
358 };
359 };
360
361 &i2c10 {
362 status = "okay";
363 clock-frequency = <100000>;
364
365 bq27441_fg: bq27441-battery@55 {
366 compatible = "ti,bq27411";
367 status = "okay";
368 reg = <0x55>;
369 };
370 };
371
372 &i2c12 {
373 status = "okay";
374 clock-frequency = <400000>;
375
376 synaptics-rmi4-i2c@20 {
377 compatible = "syna,rmi4-i2c";
378 reg = <0x20>;
379 #address-cells = <1>;
380 #size-cells = <0>;
381 interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
382
383 pinctrl-names = "default";
384 pinctrl-0 = <&ts_default_pins>;
385
386 vdd-supply = <&vreg_l28a_3p0>;
387 vio-supply = <&ts_1p8_supply>;
388
389 syna,reset-delay-ms = <200>;
390 syna,startup-delay-ms = <200>;
391
392 rmi4-f01@1 {
393 reg = <0x01>;
394 syna,nosleep-mode = <1>;
395 };
396
397 rmi4_f12: rmi4-f12@12 {
398 reg = <0x12>;
399 touchscreen-x-mm = <68>;
400 touchscreen-y-mm = <144>;
401 syna,sensor-type = <1>;
402 syna,rezero-wait-ms = <200>;
403 };
404 };
405 };
406
407 &ipa {
408 qcom,gsi-loader = "self";
409 memory-region = <&ipa_fw_mem>;
410 firmware-name = "qcom/sdm845/oneplus6/ipa_fws.mbn";
411 status = "okay";
412 };
413
414 &mdss {
415 status = "okay";
416 };
417
418 &mdss_dsi0 {
419 status = "okay";
420 vdda-supply = <&vdda_mipi_dsi0_1p2>;
421
422 /*
423 * Both devices use different panels but all other properties
424 * are common. Compatible line is declared in device dts.
425 */
426 display_panel: panel@0 {
427 status = "disabled";
428
429 reg = <0>;
430
431 vddio-supply = <&vreg_l14a_1p88>;
432
433 reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
434
435 pinctrl-names = "default";
436 pinctrl-0 = <&panel_reset_pins &panel_te_pin &panel_esd_pin>;
437
438 port {
439 panel_in: endpoint {
440 remote-endpoint = <&mdss_dsi0_out>;
441 };
442 };
443 };
444 };
445
446 &mdss_dsi0_out {
447 remote-endpoint = <&panel_in>;
448 data-lanes = <0 1 2 3>;
449 };
450
451 &mdss_dsi0_phy {
452 status = "okay";
453 vdds-supply = <&vdda_mipi_dsi0_pll>;
454 };
455
456 /* Modem/wifi */
457 &mss_pil {
458 status = "okay";
459 firmware-name = "qcom/sdm845/oneplus6/mba.mbn", "qcom/sdm845/oneplus6/modem.mbn";
460 };
461
462 &pm8998_gpios {
463 volume_down_gpio: pm8998-gpio5-state {
464 pinconf {
465 pins = "gpio5";
466 function = "normal";
467 input-enable;
468 bias-pull-up;
469 qcom,drive-strength = <0>;
470 };
471 };
472
473 volume_up_gpio: pm8998-gpio6-state {
474 pinconf {
475 pins = "gpio6";
476 function = "normal";
477 input-enable;
478 bias-pull-up;
479 qcom,drive-strength = <0>;
480 };
481 };
482 };
483
484 &pmi8998_charger {
485 status = "okay";
486 };
487
488 &pmi8998_flash {
489 status = "okay";
490
491 led-0 {
492 function = LED_FUNCTION_FLASH;
493 color = <LED_COLOR_ID_WHITE>;
494 led-sources = <1>;
495 led-max-microamp = <500000>;
496 flash-max-microamp = <1500000>;
497 flash-max-timeout-us = <1280000>;
498 };
499
500 led-1 {
501 function = LED_FUNCTION_FLASH;
502 color = <LED_COLOR_ID_YELLOW>;
503 led-sources = <2>;
504 led-max-microamp = <500000>;
505 flash-max-microamp = <1500000>;
506 flash-max-timeout-us = <1280000>;
507 };
508 };
509
510 &q6afedai {
511 dai@22 {
512 reg = <QUATERNARY_MI2S_RX>;
513 qcom,sd-lines = <1>;
514 };
515
516 dai@23 {
517 reg = <QUATERNARY_MI2S_TX>;
518 qcom,sd-lines = <0>;
519 };
520 };
521
522 &q6asmdai {
523 dai@0 {
524 reg = <0>;
525 };
526
527 dai@1 {
528 reg = <1>;
529 };
530
531 dai@2 {
532 reg = <2>;
533 };
534
535 dai@3 {
536 reg = <3>;
537 };
538
539 dai@4 {
540 reg = <4>;
541 };
542
543 dai@5 {
544 reg = <5>;
545 };
546 };
547
548 &qupv3_id_1 {
549 status = "okay";
550 };
551
552 &qupv3_id_0 {
553 status = "okay";
554 };
555
556 &qup_i2c10_default {
557 drive-strength = <2>;
558 bias-disable;
559 };
560
561 &qup_i2c12_default {
562 drive-strength = <2>;
563 bias-disable;
564 };
565
566 &qup_uart9_rx {
567 drive-strength = <2>;
568 bias-pull-up;
569 };
570
571 &qup_uart9_tx {
572 drive-strength = <2>;
573 bias-disable;
574 };
575
576 &slpi_pas {
577 firmware-name = "qcom/sdm845/oneplus6/slpi.mbn";
578 status = "okay";
579 };
580
581 &sound {
582 compatible = "qcom,sdm845-sndcard";
583 pinctrl-0 = <&quat_mi2s_active &quat_mi2s_sd0_active &quat_mi2s_sd1_active>;
584 pinctrl-names = "default";
585 status = "okay";
586
587 mm1-dai-link {
588 link-name = "MultiMedia1";
589 cpu {
590 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
591 };
592 };
593
594 mm2-dai-link {
595 link-name = "MultiMedia2";
596 cpu {
597 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
598 };
599 };
600
601 mm3-dai-link {
602 link-name = "MultiMedia3";
603 cpu {
604 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
605 };
606 };
607
608 mm4-dai-link {
609 link-name = "MultiMedia4";
610 cpu {
611 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA4>;
612 };
613 };
614
615 mm5-dai-link {
616 link-name = "MultiMedia5";
617 cpu {
618 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA5>;
619 };
620 };
621
622 mm6-dai-link {
623 link-name = "MultiMedia6";
624 cpu {
625 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA6>;
626 };
627 };
628
629 speaker_playback_dai: speaker-dai-link {
630 link-name = "Speaker Playback";
631 cpu {
632 sound-dai = <&q6afedai QUATERNARY_MI2S_RX>;
633 };
634
635 platform {
636 sound-dai = <&q6routing>;
637 };
638 };
639
640 slim-dai-link {
641 link-name = "SLIM Playback 1";
642 cpu {
643 sound-dai = <&q6afedai SLIMBUS_0_RX>;
644 };
645
646 platform {
647 sound-dai = <&q6routing>;
648 };
649
650 codec {
651 sound-dai = <&wcd9340 0>;
652 };
653 };
654
655 slimcap-dai-link {
656 link-name = "SLIM Capture 1";
657 cpu {
658 sound-dai = <&q6afedai SLIMBUS_0_TX>;
659 };
660
661 platform {
662 sound-dai = <&q6routing>;
663 };
664
665 codec {
666 sound-dai = <&wcd9340 1>;
667 };
668 };
669
670 slim2-dai-link {
671 link-name = "SLIM Playback 2";
672 cpu {
673 sound-dai = <&q6afedai SLIMBUS_1_RX>;
674 };
675
676 platform {
677 sound-dai = <&q6routing>;
678 };
679
680 codec {
681 sound-dai = <&wcd9340 2>; /* AIF2_PB */
682 };
683 };
684
685 slimcap2-dai-link {
686 link-name = "SLIM Capture 2";
687 cpu {
688 sound-dai = <&q6afedai SLIMBUS_1_TX>;
689 };
690
691 platform {
692 sound-dai = <&q6routing>;
693 };
694
695 codec {
696 sound-dai = <&wcd9340 3>; /* AIF2_CAP */
697 };
698 };
699
700 slimcap3-dai-link {
701 link-name = "SLIM Capture 3";
702 cpu {
703 sound-dai = <&q6afedai SLIMBUS_2_TX>;
704 };
705
706 platform {
707 sound-dai = <&q6routing>;
708 };
709
710 codec {
711 sound-dai = <&wcd9340 5>; /* AIF3_CAP */
712 };
713 };
714 };
715
716 &uart6 {
717 status = "okay";
718
719 pinctrl-0 = <&qup_uart6_4pin>;
720
721 bluetooth {
722 compatible = "qcom,wcn3990-bt";
723
724 /*
725 * This path is relative to the qca/
726 * subdir under lib/firmware.
727 */
728 firmware-name = "oneplus6/crnv21.bin";
729
730 vddio-supply = <&vreg_s4a_1p8>;
731 vddxo-supply = <&vreg_l7a_1p8>;
732 vddrf-supply = <&vreg_l17a_1p3>;
733 vddch0-supply = <&vreg_l25a_3p3>;
734 max-speed = <3200000>;
735 };
736 };
737
738 &uart9 {
739 label = "LS-UART1";
740 status = "okay";
741 };
742
743 &ufs_mem_hc {
744 status = "okay";
745
746 reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
747
748 vcc-supply = <&vreg_l20a_2p95>;
749 vcc-max-microamp = <600000>;
750 };
751
752 &ufs_mem_phy {
753 status = "okay";
754
755 vdda-phy-supply = <&vdda_ufs1_core>;
756 vdda-pll-supply = <&vdda_ufs1_1p2>;
757 };
758
759 &usb_1 {
760 status = "okay";
761
762 /*
763 * disable USB3 clock requirement as the device only supports
764 * USB2.
765 */
766 qcom,select-utmi-as-pipe-clk;
767 };
768
769 &usb_1_dwc3 {
770 /*
771 * We don't have the capability to switch modes yet.
772 */
773 dr_mode = "peripheral";
774
775 /* fastest mode for USB 2 */
776 maximum-speed = "high-speed";
777
778 /* Remove USB3 phy as it's unused on this device. */
779 phys = <&usb_1_hsphy>;
780 phy-names = "usb2-phy";
781 };
782
783 &usb_1_hsphy {
784 status = "okay";
785
786 vdd-supply = <&vdda_usb1_ss_core>;
787 vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
788 vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
789
790 qcom,imp-res-offset-value = <8>;
791 qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
792 qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
793 qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
794 };
795
796 &tlmm {
797 gpio-reserved-ranges = <0 4>, <81 4>;
798
799 hall_sensor_default: hall-sensor-default-state {
800 pins = "gpio124";
801 function = "gpio";
802 drive-strength = <2>;
803 bias-disable;
804 };
805
806 tri_state_key_default: tri-state-key-default-state {
807 pins = "gpio40", "gpio42", "gpio26";
808 function = "gpio";
809 drive-strength = <2>;
810 bias-disable;
811 };
812
813 ts_default_pins: ts-int-state {
814 pins = "gpio99", "gpio125";
815 function = "gpio";
816 drive-strength = <16>;
817 bias-pull-up;
818 };
819
820 panel_reset_pins: panel-reset-state {
821 pins = "gpio6", "gpio25", "gpio26";
822 function = "gpio";
823 drive-strength = <8>;
824 bias-disable;
825 };
826
827 panel_te_pin: panel-te-state {
828 pins = "gpio10";
829 function = "mdp_vsync";
830 drive-strength = <2>;
831 bias-disable;
832 };
833
834 panel_esd_pin: panel-esd-state {
835 pins = "gpio30";
836 function = "gpio";
837 drive-strength = <2>;
838 bias-pull-down;
839 };
840
841 speaker_default: speaker-default-state {
842 pins = "gpio69";
843 function = "gpio";
844 drive-strength = <16>;
845 bias-pull-up;
846 output-high;
847 };
848 };
849
850 &venus {
851 status = "okay";
852 firmware-name = "qcom/sdm845/oneplus6/venus.mbn";
853 };
854
855 &wcd9340 {
856 pinctrl-0 = <&wcd_intr_default>;
857 pinctrl-names = "default";
858 reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
859 vdd-buck-supply = <&vreg_s4a_1p8>;
860 vdd-buck-sido-supply = <&vreg_s4a_1p8>;
861 vdd-tx-supply = <&vreg_s4a_1p8>;
862 vdd-rx-supply = <&vreg_s4a_1p8>;
863 vdd-io-supply = <&vreg_s4a_1p8>;
864 };
865
866 &wifi {
867 status = "okay";
868 vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
869 vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
870 vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
871 vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
872 vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
873
874 qcom,snoc-host-cap-8bit-quirk;
875 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.