1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Copyright (c) 2022, Alexander Martinz <amartinz@shiftphones.com>
4 * Copyright (c) 2022, Caleb Connolly <caleb@connolly.tech>
5 * Copyright (c) 2022, Dylan Van Assche <me@dylanvanassche.be>
6 */
7
8 /dts-v1/;
9
10 #include <dt-bindings/gpio/gpio.h>
11 #include <dt-bindings/leds/common.h>
12 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
13 #include "sdm845.dtsi"
14 #include "pm8998.dtsi"
15 #include "pmi8998.dtsi"
16
17 / {
18 model = "SHIFT SHIFT6mq";
19 compatible = "shift,axolotl", "qcom,sdm845";
20 qcom,msm-id = <321 0x20001>;
21 qcom,board-id = <11 0>;
22
23 aliases {
24 display0 = &framebuffer0;
25 serial0 = &uart9;
26 serial1 = &uart6;
27 };
28
29 chosen {
30 #address-cells = <2>;
31 #size-cells = <2>;
32 ranges;
33
34 stdout-path = "serial0";
35
36 /* Use framebuffer setup by the bootloader. */
37 framebuffer0: framebuffer@9d400000 {
38 compatible = "simple-framebuffer";
39 reg = <0x0 0x9d400000 0x0 (1080 * 2160 * 4)>;
40 width = <1080>;
41 height = <2160>;
42 stride = <(1080 * 4)>;
43 format = "a8r8g8b8";
44 };
45 };
46
47 gpio-keys {
48 compatible = "gpio-keys";
49 autorepeat;
50
51 pinctrl-names = "default";
52 pinctrl-0 = <&volume_up_gpio>;
53
54 key-vol-up {
55 label = "volume_up";
56 linux,code = <KEY_VOLUMEUP>;
57 gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>;
58 debounce-interval = <15>;
59 };
60 };
61
62 reserved-memory {
63 framebuffer@9d400000 {
64 reg = <0x0 0x9d400000 0x0 (1080 * 2160 * 4)>;
65 no-map;
66 };
67
68 ramoops: ramoops@b0000000 {
69 compatible = "ramoops";
70 reg = <0 0xb0000000 0 0x00400000>;
71 record-size = <0x40000>;
72 console-size = <0x40000>;
73 ftrace-size = <0x40000>;
74 pmsg-size = <0x200000>;
75 ecc-size = <0x0>;
76 };
77 };
78
79 battery: battery {
80 compatible = "simple-battery";
81
82 charge-full-design-microamp-hours = <3850000>;
83 voltage-min-design-microvolt = <3600000>;
84 voltage-max-design-microvolt = <4400000>;
85 };
86
87 vph_pwr: vph-pwr-regulator {
88 compatible = "regulator-fixed";
89 regulator-name = "vph_pwr";
90 regulator-min-microvolt = <3700000>;
91 regulator-max-microvolt = <3700000>;
92 };
93
94 vreg_s4a_1p8: pm8998-smps4 {
95 compatible = "regulator-fixed";
96 regulator-name = "vreg_s4a_1p8";
97
98 regulator-min-microvolt = <1800000>;
99 regulator-max-microvolt = <1800000>;
100
101 regulator-always-on;
102 regulator-boot-on;
103
104 vin-supply = <&vph_pwr>;
105 };
106 };
107
108 &adsp_pas {
109 status = "okay";
110 firmware-name = "qcom/sdm845/axolotl/adsp.mbn";
111 };
112
113 &apps_rsc {
114 regulators-0 {
115 compatible = "qcom,pm8998-rpmh-regulators";
116 qcom,pmic-id = "a";
117
118 vdd-s1-supply = <&vph_pwr>;
119 vdd-s2-supply = <&vph_pwr>;
120 vdd-s3-supply = <&vph_pwr>;
121 vdd-s4-supply = <&vph_pwr>;
122 vdd-s5-supply = <&vph_pwr>;
123 vdd-s6-supply = <&vph_pwr>;
124 vdd-s7-supply = <&vph_pwr>;
125 vdd-s8-supply = <&vph_pwr>;
126 vdd-s9-supply = <&vph_pwr>;
127 vdd-s10-supply = <&vph_pwr>;
128 vdd-s11-supply = <&vph_pwr>;
129 vdd-s12-supply = <&vph_pwr>;
130 vdd-s13-supply = <&vph_pwr>;
131 vdd-l1-l27-supply = <&vreg_s7a_1p025>;
132 vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
133 vdd-l3-l11-supply = <&vreg_s7a_1p025>;
134 vdd-l4-l5-supply = <&vreg_s7a_1p025>;
135 vdd-l6-supply = <&vph_pwr>;
136 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
137 vdd-l9-supply = <&vreg_bob>;
138 vdd-l10-l23-l25-supply = <&vreg_bob>;
139 vdd-l13-l19-l21-supply = <&vreg_bob>;
140 vdd-l16-l28-supply = <&vreg_bob>;
141 vdd-l18-l22-supply = <&vreg_bob>;
142 vdd-l20-l24-supply = <&vreg_bob>;
143 vdd-l26-supply = <&vreg_s3a_1p35>;
144 vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
145
146 vreg_s2a_1p125: smps2 {
147 regulator-min-microvolt = <1100000>;
148 regulator-max-microvolt = <1100000>;
149 };
150
151 vreg_s3a_1p35: smps3 {
152 regulator-min-microvolt = <1352000>;
153 regulator-max-microvolt = <1352000>;
154 };
155
156 vreg_s5a_2p04: smps5 {
157 regulator-min-microvolt = <1904000>;
158 regulator-max-microvolt = <2040000>;
159 };
160
161 vreg_s7a_1p025: smps7 {
162 regulator-min-microvolt = <900000>;
163 regulator-max-microvolt = <1028000>;
164 };
165
166 vdd_qusb_hs0:
167 vdda_hp_pcie_core:
168 vdda_mipi_csi0_0p9:
169 vdda_mipi_csi1_0p9:
170 vdda_mipi_csi2_0p9:
171 vdda_mipi_dsi0_pll:
172 vdda_mipi_dsi1_pll:
173 vdda_qlink_lv:
174 vdda_qlink_lv_ck:
175 vdda_qrefs_0p875:
176 vdda_pcie_core:
177 vdda_pll_cc_ebi01:
178 vdda_pll_cc_ebi23:
179 vdda_sp_sensor:
180 vdda_ufs1_core:
181 vdda_ufs2_core:
182 vdda_usb1_ss_core:
183 vdda_usb2_ss_core:
184 vreg_l1a_0p875: ldo1 {
185 regulator-min-microvolt = <880000>;
186 regulator-max-microvolt = <880000>;
187 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
188 };
189
190 vddpx_10:
191 vreg_l2a_1p2: ldo2 {
192 regulator-min-microvolt = <1200000>;
193 regulator-max-microvolt = <1200000>;
194 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
195 regulator-always-on;
196 };
197
198 vreg_l3a_1p0: ldo3 {
199 regulator-min-microvolt = <1000000>;
200 regulator-max-microvolt = <1000000>;
201 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
202 };
203
204 vdd_wcss_cx:
205 vdd_wcss_mx:
206 vdda_wcss_pll:
207 vreg_l5a_0p8: ldo5 {
208 regulator-min-microvolt = <800000>;
209 regulator-max-microvolt = <800000>;
210 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
211 };
212
213 vddpx_13:
214 vreg_l6a_1p8: ldo6 {
215 regulator-min-microvolt = <1856000>;
216 regulator-max-microvolt = <1856000>;
217 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
218 };
219
220 vreg_l7a_1p8: ldo7 {
221 regulator-min-microvolt = <1800000>;
222 regulator-max-microvolt = <1800000>;
223 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
224 };
225
226 vreg_l8a_1p2: ldo8 {
227 regulator-min-microvolt = <1200000>;
228 regulator-max-microvolt = <1248000>;
229 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
230 };
231
232 vreg_l9a_1p8: ldo9 {
233 regulator-min-microvolt = <1704000>;
234 regulator-max-microvolt = <2928000>;
235 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
236 };
237
238 vreg_l10a_1p8: ldo10 {
239 regulator-min-microvolt = <1704000>;
240 regulator-max-microvolt = <2928000>;
241 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
242 };
243
244 vreg_l11a_1p0: ldo11 {
245 regulator-min-microvolt = <1000000>;
246 regulator-max-microvolt = <1048000>;
247 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
248 };
249
250 vdd_qfprom:
251 vdd_qfprom_sp:
252 vdda_apc1_cs_1p8:
253 vdda_gfx_cs_1p8:
254 vdda_qrefs_1p8:
255 vdda_qusb_hs0_1p8:
256 vddpx_11:
257 vreg_l12a_1p8: ldo12 {
258 regulator-min-microvolt = <1800000>;
259 regulator-max-microvolt = <1800000>;
260 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
261 };
262
263 vddpx_2:
264 vreg_l13a_2p95: ldo13 {
265 regulator-min-microvolt = <1800000>;
266 regulator-max-microvolt = <2960000>;
267 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
268 };
269
270 vreg_l14a_1p88: ldo14 {
271 regulator-min-microvolt = <1800000>;
272 regulator-max-microvolt = <1800000>;
273 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
274 };
275
276 vreg_l15a_1p8: ldo15 {
277 regulator-min-microvolt = <1800000>;
278 regulator-max-microvolt = <1800000>;
279 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
280 };
281
282 vreg_l16a_2p7: ldo16 {
283 regulator-min-microvolt = <2704000>;
284 regulator-max-microvolt = <2704000>;
285 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
286 };
287
288 vreg_l17a_1p3: ldo17 {
289 regulator-min-microvolt = <1304000>;
290 regulator-max-microvolt = <1304000>;
291 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
292 };
293
294 vreg_l18a_2p7: ldo18 {
295 regulator-min-microvolt = <2704000>;
296 regulator-max-microvolt = <2960000>;
297 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
298 };
299
300 vreg_l19a_3p0: ldo19 {
301 regulator-min-microvolt = <2856000>;
302 regulator-max-microvolt = <3104000>;
303 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
304 };
305
306 vreg_l20a_2p95: ldo20 {
307 regulator-min-microvolt = <2704000>;
308 regulator-max-microvolt = <2960000>;
309 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
310 };
311
312 vreg_l21a_2p95: ldo21 {
313 regulator-min-microvolt = <2704000>;
314 regulator-max-microvolt = <2960000>;
315 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
316 };
317
318 vreg_l22a_2p85: ldo22 {
319 regulator-min-microvolt = <2864000>;
320 regulator-max-microvolt = <3312000>;
321 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
322 };
323
324 vreg_l23a_3p3: ldo23 {
325 regulator-min-microvolt = <3000000>;
326 regulator-max-microvolt = <3312000>;
327 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
328 };
329
330 vdda_qusb_hs0_3p1:
331 vreg_l24a_3p075: ldo24 {
332 regulator-min-microvolt = <3088000>;
333 regulator-max-microvolt = <3088000>;
334 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
335 };
336
337 vreg_l25a_3p3: ldo25 {
338 regulator-min-microvolt = <3300000>;
339 regulator-max-microvolt = <3312000>;
340 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
341 };
342
343 vdda_hp_pcie_1p2:
344 vdda_hv_ebi0:
345 vdda_hv_ebi1:
346 vdda_hv_ebi2:
347 vdda_hv_ebi3:
348 vdda_mipi_csi_1p25:
349 vdda_mipi_dsi0_1p2:
350 vdda_mipi_dsi1_1p2:
351 vdda_pcie_1p2:
352 vdda_ufs1_1p2:
353 vdda_ufs2_1p2:
354 vdda_usb1_ss_1p2:
355 vdda_usb2_ss_1p2:
356 vreg_l26a_1p2: ldo26 {
357 regulator-min-microvolt = <1200000>;
358 regulator-max-microvolt = <1200000>;
359 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
360 };
361
362 vreg_l28a_3p0: ldo28 {
363 regulator-min-microvolt = <2856000>;
364 regulator-max-microvolt = <3008000>;
365 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
366 };
367
368 vreg_lvs1a_1p8: lvs1 {
369 regulator-min-microvolt = <1800000>;
370 regulator-max-microvolt = <1800000>;
371 };
372
373 vreg_lvs2a_1p8: lvs2 {
374 regulator-min-microvolt = <1800000>;
375 regulator-max-microvolt = <1800000>;
376 };
377 };
378
379 regulators-1 {
380 compatible = "qcom,pmi8998-rpmh-regulators";
381 qcom,pmic-id = "b";
382
383 vdd-bob-supply = <&vph_pwr>;
384
385 vreg_bob: bob {
386 regulator-min-microvolt = <3312000>;
387 regulator-max-microvolt = <3600000>;
388 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
389 regulator-allow-bypass;
390 };
391 };
392
393 regulators-2 {
394 compatible = "qcom,pm8005-rpmh-regulators";
395 qcom,pmic-id = "c";
396
397 vdd-s1-supply = <&vph_pwr>;
398 vdd-s2-supply = <&vph_pwr>;
399 vdd-s3-supply = <&vph_pwr>;
400 vdd-s4-supply = <&vph_pwr>;
401
402 vreg_s3c_0p6: smps3 {
403 regulator-min-microvolt = <600000>;
404 regulator-max-microvolt = <600000>;
405 };
406 };
407 };
408
409 &cdsp_pas {
410 status = "okay";
411 firmware-name = "qcom/sdm845/axolotl/cdsp.mbn";
412 };
413
414 &gcc {
415 protected-clocks = <GCC_QSPI_CORE_CLK>,
416 <GCC_QSPI_CORE_CLK_SRC>,
417 <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
418 <GCC_LPASS_Q6_AXI_CLK>,
419 <GCC_LPASS_SWAY_CLK>;
420 };
421
422 &gmu {
423 status = "okay";
424 };
425
426 &gpu {
427 status = "okay";
428
429 zap-shader {
430 memory-region = <&gpu_mem>;
431 firmware-name = "qcom/sdm845/axolotl/a630_zap.mbn";
432 };
433 };
434
435 &i2c5 {
436 status = "okay";
437
438 touchscreen@38 {
439 compatible = "focaltech,fts8719";
440 reg = <0x38>;
441 wakeup-source;
442 interrupt-parent = <&tlmm>;
443 interrupts = <125 IRQ_TYPE_EDGE_FALLING>;
444 vdd-supply = <&vreg_l28a_3p0>;
445 vcc-i2c-supply = <&vreg_l14a_1p88>;
446
447 pinctrl-names = "default", "suspend";
448 pinctrl-0 = <&ts_int_active &ts_reset_active>;
449 pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
450
451 reset-gpio = <&tlmm 99 GPIO_ACTIVE_HIGH>;
452 irq-gpio = <&tlmm 125 GPIO_TRANSITORY>;
453 touchscreen-size-x = <1080>;
454 touchscreen-size-y = <2160>;
455 focaltech,max-touch-number = <5>;
456 };
457 };
458
459 &i2c10 {
460 /* SMB1355@0x0C */
461 };
462
463 &ipa {
464 qcom,gsi-loader = "self";
465 memory-region = <&ipa_fw_mem>;
466 firmware-name = "qcom/sdm845/axolotl/ipa_fws.mbn";
467 status = "okay";
468 };
469
470 &mdss {
471 status = "okay";
472 };
473
474 &mdss_dsi0 {
475 status = "okay";
476 vdda-supply = <&vdda_mipi_dsi0_1p2>;
477
478 panel@0 {
479 compatible = "visionox,rm69299-shift";
480 status = "okay";
481 reg = <0>;
482 vdda-supply = <&vreg_l14a_1p88>;
483 vdd3p3-supply = <&vreg_l28a_3p0>;
484
485 #address-cells = <1>;
486 #size-cells = <0>;
487
488 reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
489
490 pinctrl-names = "default", "sleep";
491 pinctrl-0 = <&sde_dsi_active &sde_te_active>;
492 pinctrl-1 = <&sde_dsi_suspend &sde_te_suspend>;
493
494 port {
495 panel_in_0: endpoint {
496 remote-endpoint = <&mdss_dsi0_out>;
497 };
498 };
499 };
500 };
501
502 &mdss_dsi0_out {
503 remote-endpoint = <&panel_in_0>;
504 data-lanes = <0 1 2 3>;
505 };
506
507 &mdss_dsi0_phy {
508 status = "okay";
509 vdds-supply = <&vdda_mipi_dsi0_pll>;
510 };
511
512 &mss_pil {
513 status = "okay";
514 firmware-name = "qcom/sdm845/axolotl/mba.mbn", "qcom/sdm845/axolotl/modem.mbn";
515 };
516
517 &pm8998_gpios {
518 volume_up_gpio: pm8998-gpio6-state {
519 pinconf {
520 pins = "gpio6";
521 function = "normal";
522 input-enable;
523 bias-pull-up;
524 qcom,drive-strength = <0>;
525 };
526 };
527 };
528
529 &pmi8998_charger {
530 monitored-battery = <&battery>;
531
532 status = "okay";
533 };
534
535 &pm8998_resin {
536 linux,code = <KEY_VOLUMEDOWN>;
537 status = "okay";
538 };
539
540 &pmi8998_lpg {
541 status = "okay";
542
543 multi-led {
544 color = <LED_COLOR_ID_RGB>;
545 function = LED_FUNCTION_STATUS;
546
547 #address-cells = <1>;
548 #size-cells = <0>;
549
550 led@3 {
551 reg = <3>;
552 color = <LED_COLOR_ID_BLUE>;
553 };
554
555 led@4 {
556 reg = <4>;
557 color = <LED_COLOR_ID_GREEN>;
558 };
559
560 led@5 {
561 reg = <5>;
562 color = <LED_COLOR_ID_RED>;
563 };
564 };
565 };
566
567 &pmi8998_flash {
568 status = "okay";
569
570 led-0 {
571 function = LED_FUNCTION_FLASH;
572 color = <LED_COLOR_ID_WHITE>;
573 led-sources = <1>;
574 led-max-microamp = <100000>;
575 flash-max-microamp = <1100000>;
576 flash-max-timeout-us = <1280000>;
577 };
578
579 led-1 {
580 function = LED_FUNCTION_FLASH;
581 color = <LED_COLOR_ID_YELLOW>;
582 led-sources = <2>;
583 led-max-microamp = <100000>;
584 flash-max-microamp = <1100000>;
585 flash-max-timeout-us = <1280000>;
586 };
587 };
588
589 &qup_uart9_rx {
590 drive-strength = <2>;
591 bias-pull-up;
592 };
593
594 &qup_uart9_tx {
595 drive-strength = <2>;
596 bias-disable;
597 };
598
599 &qupv3_id_0 {
600 status = "okay";
601 };
602
603 &qupv3_id_1 {
604 status = "okay";
605 };
606
607 &slpi_pas {
608 firmware-name = "qcom/sdm845/axolotl/slpi.mbn";
609 status = "okay";
610 };
611
612 &tlmm {
613 gpio-reserved-ranges = <0 4>, <81 4>;
614
615 sde_dsi_active: sde-dsi-active-state {
616 pins = "gpio6", "gpio11";
617 function = "gpio";
618 drive-strength = <8>;
619 bias-disable;
620 };
621
622 sde_dsi_suspend: sde-dsi-suspend-state {
623 pins = "gpio6", "gpio11";
624 function = "gpio";
625 drive-strength = <2>;
626 bias-pull-down;
627 };
628
629 sde_te_active: sde-te-active-state {
630 pins = "gpio10";
631 function = "mdp_vsync";
632 drive-strength = <2>;
633 bias-pull-down;
634 };
635
636 sde_te_suspend: sde-te-suspend-state {
637 pins = "gpio10";
638 function = "mdp_vsync";
639 drive-strength = <2>;
640 bias-pull-down;
641 };
642
643 ts_int_active: ts-int-active-state {
644 pins = "gpio125";
645 function = "gpio";
646 drive-strength = <8>;
647 bias-pull-up;
648 };
649
650 ts_int_suspend: ts-int-suspend-state {
651 pins = "gpio125";
652 function = "gpio";
653 drive-strength = <2>;
654 bias-pull-down;
655 };
656
657 ts_reset_active: ts-reset-active-state {
658 pins = "gpio99";
659 function = "gpio";
660 drive-strength = <8>;
661 bias-pull-up;
662 };
663
664 ts_reset_suspend: ts-reset-suspend-state {
665 pins = "gpio99";
666 function = "gpio";
667 drive-strength = <2>;
668 bias-pull-down;
669 };
670 };
671
672 &uart6 {
673 status = "okay";
674
675 pinctrl-0 = <&qup_uart6_4pin>;
676
677 bluetooth {
678 compatible = "qcom,wcn3990-bt";
679
680 /*
681 * This path is relative to the qca/
682 * subdir under lib/firmware.
683 */
684 firmware-name = "axolotl/crnv21.bin";
685
686 vddio-supply = <&vreg_s4a_1p8>;
687 vddxo-supply = <&vreg_l7a_1p8>;
688 vddrf-supply = <&vreg_l17a_1p3>;
689 vddch0-supply = <&vreg_l25a_3p3>;
690 max-speed = <3200000>;
691 };
692 };
693
694 &uart9 {
695 status = "okay";
696 };
697
698 &ufs_mem_hc {
699 status = "okay";
700
701 reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
702
703 vcc-supply = <&vreg_l20a_2p95>;
704 vcc-max-microamp = <600000>;
705 };
706
707 &ufs_mem_phy {
708 status = "okay";
709
710 vdda-phy-supply = <&vdda_ufs1_core>;
711 vdda-pll-supply = <&vdda_ufs1_1p2>;
712 };
713
714 &usb_1 {
715 status = "okay";
716 };
717
718 &usb_1_dwc3 {
719 dr_mode = "peripheral";
720 };
721
722 &usb_1_hsphy {
723 status = "okay";
724
725 vdd-supply = <&vreg_l1a_0p875>;
726 vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
727 vdda-pll-supply = <&vreg_l12a_1p8>;
728 };
729
730 &usb_1_qmpphy {
731 status = "okay";
732
733 vdda-phy-supply = <&vreg_l26a_1p2>;
734 vdda-pll-supply = <&vreg_l1a_0p875>;
735 };
736
737 &venus {
738 status = "okay";
739 firmware-name = "qcom/sdm845/axolotl/venus.mbn";
740 };
741
742 &wifi {
743 status = "okay";
744
745 vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
746 vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
747 vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
748 vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
749 vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
750
751 qcom,snoc-host-cap-8bit-quirk;
752 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.