1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2 /*
3 * Copyright (c) 2017 Fuzhou Rockchip Electronics Co., Ltd.
4 * Copyright (c) 2018 Akash Gajjar <Akash_Gajjar@mentor.com>
5 * Copyright (c) 2020 Tobias Schramm <t.schramm@manjaro.org>
6 */
7
8 /dts-v1/;
9 #include <dt-bindings/input/gpio-keys.h>
10 #include <dt-bindings/input/linux-event-codes.h>
11 #include <dt-bindings/pwm/pwm.h>
12 #include <dt-bindings/usb/pd.h>
13 #include <dt-bindings/leds/common.h>
14 #include "rk3399.dtsi"
15
16 / {
17 model = "Pine64 Pinebook Pro";
18 compatible = "pine64,pinebook-pro", "rockchip,rk3399";
19 chassis-type = "laptop";
20
21 aliases {
22 mmc0 = &sdio0;
23 mmc1 = &sdmmc;
24 mmc2 = &sdhci;
25 };
26
27 chosen {
28 stdout-path = "serial2:1500000n8";
29 };
30
31 backlight: edp-backlight {
32 compatible = "pwm-backlight";
33 power-supply = <&vcc_12v>;
34 pwms = <&pwm0 0 125000 0>;
35 };
36
37 bat: battery {
38 compatible = "simple-battery";
39 charge-full-design-microamp-hours = <10000000>;
40 voltage-max-design-microvolt = <4350000>;
41 voltage-min-design-microvolt = <3000000>;
42 };
43
44 edp_panel: edp-panel {
45 compatible = "boe,nv140fhmn49";
46 backlight = <&backlight>;
47 enable-gpios = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
48 pinctrl-names = "default";
49 pinctrl-0 = <&panel_en_pin>;
50 power-supply = <&vcc3v3_panel>;
51
52 port {
53 panel_in_edp: endpoint {
54 remote-endpoint = <&edp_out_panel>;
55 };
56 };
57 };
58
59 /*
60 * Use separate nodes for gpio-keys to allow for selective deactivation
61 * of wakeup sources via sysfs without disabling the whole key
62 */
63 gpio-key-lid {
64 compatible = "gpio-keys";
65 pinctrl-names = "default";
66 pinctrl-0 = <&lidbtn_pin>;
67
68 switch-lid {
69 debounce-interval = <20>;
70 gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_LOW>;
71 label = "Lid";
72 linux,code = <SW_LID>;
73 linux,input-type = <EV_SW>;
74 wakeup-event-action = <EV_ACT_DEASSERTED>;
75 wakeup-source;
76 };
77 };
78
79 gpio-key-power {
80 compatible = "gpio-keys";
81 pinctrl-names = "default";
82 pinctrl-0 = <&pwrbtn_pin>;
83
84 key-power {
85 debounce-interval = <20>;
86 gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
87 label = "Power";
88 linux,code = <KEY_POWER>;
89 wakeup-source;
90 };
91 };
92
93 leds {
94 compatible = "gpio-leds";
95 pinctrl-names = "default";
96 pinctrl-0 = <&pwr_led_pin &slp_led_pin>;
97
98 green_led: led-0 {
99 color = <LED_COLOR_ID_GREEN>;
100 default-state = "on";
101 function = LED_FUNCTION_POWER;
102 gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
103 label = "green:power";
104 };
105
106 red_led: led-1 {
107 color = <LED_COLOR_ID_RED>;
108 default-state = "off";
109 function = LED_FUNCTION_STANDBY;
110 gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
111 label = "red:standby";
112 panic-indicator;
113 retain-state-suspended;
114 };
115 };
116
117 /* Power sequence for SDIO WiFi module */
118 sdio_pwrseq: sdio-pwrseq {
119 compatible = "mmc-pwrseq-simple";
120 clocks = <&rk808 1>;
121 clock-names = "ext_clock";
122 pinctrl-names = "default";
123 pinctrl-0 = <&wifi_enable_h_pin>;
124 post-power-on-delay-ms = <100>;
125 power-off-delay-us = <500000>;
126
127 /* WL_REG_ON on module */
128 reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
129 };
130
131 /* Audio components */
132 es8316-sound {
133 compatible = "simple-audio-card";
134 pinctrl-names = "default";
135 pinctrl-0 = <&hp_det_pin>;
136 simple-audio-card,name = "rockchip,es8316-codec";
137 simple-audio-card,format = "i2s";
138 simple-audio-card,mclk-fs = <256>;
139
140 simple-audio-card,widgets =
141 "Microphone", "Mic Jack",
142 "Headphone", "Headphones",
143 "Speaker", "Speaker";
144 simple-audio-card,routing =
145 "MIC1", "Mic Jack",
146 "Headphones", "HPOL",
147 "Headphones", "HPOR",
148 "Speaker Amplifier INL", "HPOL",
149 "Speaker Amplifier INR", "HPOR",
150 "Speaker", "Speaker Amplifier OUTL",
151 "Speaker", "Speaker Amplifier OUTR";
152
153 simple-audio-card,hp-det-gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>;
154 simple-audio-card,aux-devs = <&speaker_amp>;
155 simple-audio-card,pin-switches = "Speaker";
156
157 simple-audio-card,cpu {
158 sound-dai = <&i2s1>;
159 };
160
161 simple-audio-card,codec {
162 sound-dai = <&es8316>;
163 };
164 };
165
166 speaker_amp: speaker-amplifier {
167 compatible = "simple-audio-amplifier";
168 enable-gpios = <&gpio4 RK_PD3 GPIO_ACTIVE_HIGH>;
169 sound-name-prefix = "Speaker Amplifier";
170 VCC-supply = <&pa_5v>;
171 };
172
173 /* Power tree */
174 /* Root power source */
175 vcc_sysin: vcc-sysin {
176 compatible = "regulator-fixed";
177 regulator-name = "vcc_sysin";
178 regulator-always-on;
179 regulator-boot-on;
180 };
181
182 /* Regulators supplied by vcc_sysin */
183 /* LCD backlight supply */
184 vcc_12v: vcc-12v {
185 compatible = "regulator-fixed";
186 regulator-name = "vcc_12v";
187 regulator-always-on;
188 regulator-boot-on;
189 regulator-min-microvolt = <12000000>;
190 regulator-max-microvolt = <12000000>;
191 vin-supply = <&vcc_sysin>;
192
193 regulator-state-mem {
194 regulator-off-in-suspend;
195 };
196 };
197
198 /* Main 3.3 V supply */
199 vcc3v3_sys: wifi_bat: vcc3v3-sys {
200 compatible = "regulator-fixed";
201 regulator-name = "vcc3v3_sys";
202 regulator-always-on;
203 regulator-boot-on;
204 regulator-min-microvolt = <3300000>;
205 regulator-max-microvolt = <3300000>;
206 vin-supply = <&vcc_sysin>;
207
208 regulator-state-mem {
209 regulator-on-in-suspend;
210 };
211 };
212
213 /* 5 V USB power supply */
214 vcc5v0_usb: pa_5v: vcc5v0-usb-regulator {
215 compatible = "regulator-fixed";
216 enable-active-high;
217 gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
218 pinctrl-names = "default";
219 pinctrl-0 = <&pwr_5v_pin>;
220 regulator-name = "vcc5v0_usb";
221 regulator-always-on;
222 regulator-min-microvolt = <5000000>;
223 regulator-max-microvolt = <5000000>;
224 vin-supply = <&vcc_sysin>;
225
226 regulator-state-mem {
227 regulator-off-in-suspend;
228 };
229 };
230
231 /* RK3399 logic supply */
232 vdd_log: vdd-log {
233 compatible = "pwm-regulator";
234 pwms = <&pwm2 0 25000 1>;
235 pwm-supply = <&vcc_sysin>;
236 regulator-name = "vdd_log";
237 regulator-always-on;
238 regulator-boot-on;
239 regulator-min-microvolt = <800000>;
240 regulator-max-microvolt = <1400000>;
241
242 regulator-state-mem {
243 regulator-on-in-suspend;
244 };
245 };
246
247 /* Regulators supplied by vcc3v3_sys */
248 /* 0.9 V supply, always on */
249 vcc_0v9: vcc-0v9 {
250 compatible = "regulator-fixed";
251 regulator-name = "vcc_0v9";
252 regulator-always-on;
253 regulator-boot-on;
254 regulator-min-microvolt = <900000>;
255 regulator-max-microvolt = <900000>;
256 vin-supply = <&vcc3v3_sys>;
257 };
258
259 /* S3 1.8 V supply, switched by vcc1v8_s3 */
260 vcca1v8_s3: vcc1v8-s3 {
261 compatible = "regulator-fixed";
262 regulator-name = "vcca1v8_s3";
263 regulator-always-on;
264 regulator-boot-on;
265 regulator-min-microvolt = <1800000>;
266 regulator-max-microvolt = <1800000>;
267 vin-supply = <&vcc3v3_sys>;
268 };
269
270 /* micro SD card power */
271 vcc3v0_sd: vcc3v0-sd {
272 compatible = "regulator-fixed";
273 enable-active-high;
274 gpio = <&gpio0 RK_PA1 GPIO_ACTIVE_HIGH>;
275 pinctrl-names = "default";
276 pinctrl-0 = <&sdmmc0_pwr_h_pin>;
277 regulator-name = "vcc3v0_sd";
278 regulator-always-on;
279 regulator-min-microvolt = <3000000>;
280 regulator-max-microvolt = <3000000>;
281 vin-supply = <&vcc3v3_sys>;
282
283 regulator-state-mem {
284 regulator-off-in-suspend;
285 };
286 };
287
288 /* LCD panel power, called VCC3V3_S0 in schematic */
289 vcc3v3_panel: vcc3v3-panel {
290 compatible = "regulator-fixed";
291 enable-active-high;
292 gpio = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
293 pinctrl-names = "default";
294 pinctrl-0 = <&lcdvcc_en_pin>;
295 regulator-name = "vcc3v3_panel";
296 regulator-always-on;
297 regulator-min-microvolt = <3300000>;
298 regulator-max-microvolt = <3300000>;
299 regulator-enable-ramp-delay = <100000>;
300 vin-supply = <&vcc3v3_sys>;
301
302 regulator-state-mem {
303 regulator-off-in-suspend;
304 };
305 };
306
307 /* M.2 adapter power, switched by vcc1v8_s3 */
308 vcc3v3_ssd: vcc3v3-ssd {
309 compatible = "regulator-fixed";
310 regulator-name = "vcc3v3_ssd";
311 regulator-min-microvolt = <3300000>;
312 regulator-max-microvolt = <3300000>;
313 vin-supply = <&vcc3v3_sys>;
314 };
315
316 /* Regulators supplied by vcc5v0_usb */
317 /* USB 3 port power supply regulator */
318 vcc5v0_otg: vcc5v0-otg {
319 compatible = "regulator-fixed";
320 enable-active-high;
321 gpio = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
322 pinctrl-names = "default";
323 pinctrl-0 = <&vcc5v0_host_en_pin>;
324 regulator-name = "vcc5v0_otg";
325 regulator-always-on;
326 regulator-min-microvolt = <5000000>;
327 regulator-max-microvolt = <5000000>;
328 vin-supply = <&vcc5v0_usb>;
329
330 regulator-state-mem {
331 regulator-off-in-suspend;
332 };
333 };
334
335 /* Regulators supplied by vcc5v0_usb */
336 /* Type C port power supply regulator */
337 vbus_5vout: vbus_typec: vbus-5vout {
338 compatible = "regulator-fixed";
339 enable-active-high;
340 gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>;
341 pinctrl-names = "default";
342 pinctrl-0 = <&vcc5v0_typec0_en_pin>;
343 regulator-name = "vbus_5vout";
344 regulator-min-microvolt = <5000000>;
345 regulator-max-microvolt = <5000000>;
346 vin-supply = <&vcc5v0_usb>;
347
348 regulator-state-mem {
349 regulator-off-in-suspend;
350 };
351 };
352
353 /* Regulators supplied by vcc_1v8 */
354 /* Primary 0.9 V LDO */
355 vcca0v9_s3: vcca0v9-s3 {
356 compatible = "regulator-fixed";
357 regulator-name = "vcc0v9_s3";
358 regulator-min-microvolt = <5000000>;
359 regulator-max-microvolt = <5000000>;
360 vin-supply = <&vcc_1v8>;
361
362 regulator-state-mem {
363 regulator-on-in-suspend;
364 };
365 };
366
367 mains_charger: dc-charger {
368 compatible = "gpio-charger";
369 charger-type = "mains";
370 gpios = <&gpio4 RK_PD0 GPIO_ACTIVE_LOW>;
371
372 /* Also triggered by USB charger */
373 pinctrl-names = "default";
374 pinctrl-0 = <&dc_det_pin>;
375 };
376 };
377
378 &cpu_b0 {
379 cpu-supply = <&vdd_cpu_b>;
380 };
381
382 &cpu_b1 {
383 cpu-supply = <&vdd_cpu_b>;
384 };
385
386 &cpu_l0 {
387 cpu-supply = <&vdd_cpu_l>;
388 };
389
390 &cpu_l1 {
391 cpu-supply = <&vdd_cpu_l>;
392 };
393
394 &cpu_l2 {
395 cpu-supply = <&vdd_cpu_l>;
396 };
397
398 &cpu_l3 {
399 cpu-supply = <&vdd_cpu_l>;
400 };
401
402 &edp {
403 force-hpd;
404 pinctrl-names = "default";
405 pinctrl-0 = <&edp_hpd>;
406 status = "okay";
407
408 ports {
409 edp_out: port@1 {
410 reg = <1>;
411 #address-cells = <1>;
412 #size-cells = <0>;
413
414 edp_out_panel: endpoint@0 {
415 reg = <0>;
416 remote-endpoint = <&panel_in_edp>;
417 };
418 };
419 };
420 };
421
422 &emmc_phy {
423 status = "okay";
424 };
425
426 &gpu {
427 mali-supply = <&vdd_gpu>;
428 status = "okay";
429 };
430
431 &hdmi_sound {
432 status = "okay";
433 };
434
435 &i2c0 {
436 clock-frequency = <400000>;
437 i2c-scl-falling-time-ns = <4>;
438 i2c-scl-rising-time-ns = <168>;
439 status = "okay";
440
441 rk808: pmic@1b {
442 compatible = "rockchip,rk808";
443 reg = <0x1b>;
444 #clock-cells = <1>;
445 clock-output-names = "xin32k", "rk808-clkout2";
446 interrupt-parent = <&gpio3>;
447 interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
448 pinctrl-names = "default";
449 pinctrl-0 = <&pmic_int_l_pin>;
450 rockchip,system-power-controller;
451 wakeup-source;
452
453 vcc1-supply = <&vcc_sysin>;
454 vcc2-supply = <&vcc_sysin>;
455 vcc3-supply = <&vcc_sysin>;
456 vcc4-supply = <&vcc_sysin>;
457 vcc6-supply = <&vcc_sysin>;
458 vcc7-supply = <&vcc_sysin>;
459 vcc8-supply = <&vcc3v3_sys>;
460 vcc9-supply = <&vcc_sysin>;
461 vcc10-supply = <&vcc_sysin>;
462 vcc11-supply = <&vcc_sysin>;
463 vcc12-supply = <&vcc3v3_sys>;
464
465 regulators {
466 /* rk3399 center logic supply */
467 vdd_center: DCDC_REG1 {
468 regulator-name = "vdd_center";
469 regulator-always-on;
470 regulator-boot-on;
471 regulator-min-microvolt = <750000>;
472 regulator-max-microvolt = <1350000>;
473 regulator-ramp-delay = <6001>;
474
475 regulator-state-mem {
476 regulator-off-in-suspend;
477 };
478 };
479
480 vdd_cpu_l: DCDC_REG2 {
481 regulator-name = "vdd_cpu_l";
482 regulator-always-on;
483 regulator-boot-on;
484 regulator-min-microvolt = <750000>;
485 regulator-max-microvolt = <1350000>;
486 regulator-ramp-delay = <6001>;
487
488 regulator-state-mem {
489 regulator-off-in-suspend;
490 };
491 };
492
493 vcc_ddr: DCDC_REG3 {
494 regulator-name = "vcc_ddr";
495 regulator-always-on;
496 regulator-boot-on;
497
498 regulator-state-mem {
499 regulator-on-in-suspend;
500 };
501 };
502
503 vcc_1v8: vcc_wl: DCDC_REG4 {
504 regulator-name = "vcc_1v8";
505 regulator-always-on;
506 regulator-boot-on;
507 regulator-min-microvolt = <1800000>;
508 regulator-max-microvolt = <1800000>;
509
510 regulator-state-mem {
511 regulator-on-in-suspend;
512 regulator-suspend-microvolt = <1800000>;
513 };
514 };
515
516 /* not used */
517 LDO_REG1 {
518 };
519
520 /* not used */
521 LDO_REG2 {
522 };
523
524 vcc1v8_pmupll: LDO_REG3 {
525 regulator-name = "vcc1v8_pmupll";
526 regulator-always-on;
527 regulator-boot-on;
528 regulator-min-microvolt = <1800000>;
529 regulator-max-microvolt = <1800000>;
530
531 regulator-state-mem {
532 regulator-on-in-suspend;
533 regulator-suspend-microvolt = <1800000>;
534 };
535 };
536
537 vcc_sdio: LDO_REG4 {
538 regulator-name = "vcc_sdio";
539 regulator-always-on;
540 regulator-boot-on;
541 regulator-min-microvolt = <1800000>;
542 regulator-max-microvolt = <3000000>;
543
544 regulator-state-mem {
545 regulator-on-in-suspend;
546 regulator-suspend-microvolt = <3000000>;
547 };
548 };
549
550 vcca3v0_codec: LDO_REG5 {
551 regulator-name = "vcca3v0_codec";
552 regulator-always-on;
553 regulator-boot-on;
554 regulator-min-microvolt = <3000000>;
555 regulator-max-microvolt = <3000000>;
556
557 regulator-state-mem {
558 regulator-off-in-suspend;
559 };
560 };
561
562 vcc_1v5: LDO_REG6 {
563 regulator-name = "vcc_1v5";
564 regulator-always-on;
565 regulator-boot-on;
566 regulator-min-microvolt = <1500000>;
567 regulator-max-microvolt = <1500000>;
568
569 regulator-state-mem {
570 regulator-on-in-suspend;
571 regulator-suspend-microvolt = <1500000>;
572 };
573 };
574
575 vcca1v8_codec: LDO_REG7 {
576 regulator-name = "vcca1v8_codec";
577 regulator-always-on;
578 regulator-boot-on;
579 regulator-min-microvolt = <1800000>;
580 regulator-max-microvolt = <1800000>;
581
582 regulator-state-mem {
583 regulator-off-in-suspend;
584 };
585 };
586
587 vcc_3v0: LDO_REG8 {
588 regulator-name = "vcc_3v0";
589 regulator-always-on;
590 regulator-boot-on;
591 regulator-min-microvolt = <3000000>;
592 regulator-max-microvolt = <3000000>;
593
594 regulator-state-mem {
595 regulator-on-in-suspend;
596 regulator-suspend-microvolt = <3000000>;
597 };
598 };
599
600 vcc3v3_s3: SWITCH_REG1 {
601 regulator-name = "vcc3v3_s3";
602 regulator-always-on;
603 regulator-boot-on;
604
605 regulator-state-mem {
606 regulator-off-in-suspend;
607 };
608 };
609
610 vcc3v3_s0: SWITCH_REG2 {
611 regulator-name = "vcc3v3_s0";
612 regulator-always-on;
613 regulator-boot-on;
614
615 regulator-state-mem {
616 regulator-off-in-suspend;
617 };
618 };
619 };
620 };
621
622 vdd_cpu_b: regulator@40 {
623 compatible = "silergy,syr827";
624 reg = <0x40>;
625 fcs,suspend-voltage-selector = <1>;
626 pinctrl-names = "default";
627 pinctrl-0 = <&vsel1_pin>;
628 regulator-name = "vdd_cpu_b";
629 regulator-always-on;
630 regulator-boot-on;
631 regulator-min-microvolt = <712500>;
632 regulator-max-microvolt = <1500000>;
633 regulator-ramp-delay = <1000>;
634 vin-supply = <&vcc_1v8>;
635
636 regulator-state-mem {
637 regulator-off-in-suspend;
638 };
639 };
640
641 vdd_gpu: regulator@41 {
642 compatible = "silergy,syr828";
643 reg = <0x41>;
644 fcs,suspend-voltage-selector = <1>;
645 pinctrl-names = "default";
646 pinctrl-0 = <&vsel2_pin>;
647 regulator-name = "vdd_gpu";
648 regulator-always-on;
649 regulator-boot-on;
650 regulator-min-microvolt = <712500>;
651 regulator-max-microvolt = <1500000>;
652 regulator-ramp-delay = <1000>;
653 vin-supply = <&vcc_1v8>;
654
655 regulator-state-mem {
656 regulator-off-in-suspend;
657 };
658 };
659 };
660
661 &i2c1 {
662 clock-frequency = <100000>;
663 i2c-scl-falling-time-ns = <4>;
664 i2c-scl-rising-time-ns = <168>;
665 status = "okay";
666
667 es8316: audio-codec@11 {
668 compatible = "everest,es8316";
669 reg = <0x11>;
670 clocks = <&cru SCLK_I2S_8CH_OUT>;
671 clock-names = "mclk";
672 #sound-dai-cells = <0>;
673 };
674 };
675
676 &i2c3 {
677 i2c-scl-falling-time-ns = <15>;
678 i2c-scl-rising-time-ns = <450>;
679 status = "okay";
680 };
681
682 &i2c4 {
683 i2c-scl-falling-time-ns = <20>;
684 i2c-scl-rising-time-ns = <600>;
685 status = "okay";
686
687 fusb0: fusb30x@22 {
688 compatible = "fcs,fusb302";
689 reg = <0x22>;
690 interrupt-parent = <&gpio1>;
691 interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
692 pinctrl-names = "default";
693 pinctrl-0 = <&fusb0_int_pin>;
694 vbus-supply = <&vbus_typec>;
695
696 connector {
697 compatible = "usb-c-connector";
698 data-role = "dual";
699 label = "USB-C";
700 op-sink-microwatt = <1000000>;
701 power-role = "dual";
702 sink-pdos =
703 <PDO_FIXED(5000, 2500, PDO_FIXED_USB_COMM)>;
704 source-pdos =
705 <PDO_FIXED(5000, 1400, PDO_FIXED_USB_COMM)>;
706 try-power-role = "sink";
707
708 ports {
709 #address-cells = <1>;
710 #size-cells = <0>;
711
712 port@0 {
713 reg = <0>;
714
715 usbc_hs: endpoint {
716 remote-endpoint =
717 <&u2phy0_typec_hs>;
718 };
719 };
720
721 port@1 {
722 reg = <1>;
723
724 usbc_ss: endpoint {
725 remote-endpoint =
726 <&tcphy0_typec_ss>;
727 };
728 };
729
730 port@2 {
731 reg = <2>;
732
733 usbc_dp: endpoint {
734 remote-endpoint =
735 <&tcphy0_typec_dp>;
736 };
737 };
738 };
739 };
740 };
741
742 cw2015@62 {
743 compatible = "cellwise,cw2015";
744 reg = <0x62>;
745 cellwise,battery-profile = /bits/ 8 <
746 0x17 0x67 0x80 0x73 0x6E 0x6C 0x6B 0x63
747 0x77 0x51 0x5C 0x58 0x50 0x4C 0x48 0x36
748 0x15 0x0C 0x0C 0x19 0x5B 0x7D 0x6F 0x69
749 0x69 0x5B 0x0C 0x29 0x20 0x40 0x52 0x59
750 0x57 0x56 0x54 0x4F 0x3B 0x1F 0x7F 0x17
751 0x06 0x1A 0x30 0x5A 0x85 0x93 0x96 0x2D
752 0x48 0x77 0x9C 0xB3 0x80 0x52 0x94 0xCB
753 0x2F 0x00 0x64 0xA5 0xB5 0x11 0xF0 0x11
754 >;
755 cellwise,monitor-interval-ms = <5000>;
756 monitored-battery = <&bat>;
757 power-supplies = <&mains_charger>, <&fusb0>;
758 };
759 };
760
761 &i2s1 {
762 pinctrl-names = "default";
763 pinctrl-0 = <&i2s_8ch_mclk_pin>, <&i2s1_2ch_bus>;
764 rockchip,capture-channels = <8>;
765 rockchip,playback-channels = <8>;
766 status = "okay";
767 };
768
769 &io_domains {
770 audio-supply = <&vcc_3v0>;
771 gpio1830-supply = <&vcc_3v0>;
772 sdmmc-supply = <&vcc_sdio>;
773 status = "okay";
774 };
775
776 &pcie_phy {
777 status = "okay";
778 };
779
780 &pcie0 {
781 ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
782 num-lanes = <4>;
783 pinctrl-names = "default";
784 pinctrl-0 = <&pcie_clkreqn_cpm>;
785 vpcie0v9-supply = <&vcca0v9_s3>;
786 vpcie1v8-supply = <&vcca1v8_s3>;
787 vpcie3v3-supply = <&vcc3v3_ssd>;
788 status = "okay";
789 };
790
791 &pinctrl {
792 buttons {
793 pwrbtn_pin: pwrbtn-pin {
794 rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
795 };
796
797 lidbtn_pin: lidbtn-pin {
798 rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
799 };
800 };
801
802 dc-charger {
803 dc_det_pin: dc-det-pin {
804 rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
805 };
806 };
807
808 es8316 {
809 hp_det_pin: hp-det-pin {
810 rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
811 };
812 };
813
814 fusb302x {
815 fusb0_int_pin: fusb0-int-pin {
816 rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
817 };
818 };
819
820 i2s1 {
821 i2s_8ch_mclk_pin: i2s-8ch-mclk-pin {
822 rockchip,pins = <4 RK_PA0 1 &pcfg_pull_none>;
823 };
824 };
825
826 lcd-panel {
827 lcdvcc_en_pin: lcdvcc-en-pin {
828 rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
829 };
830
831 panel_en_pin: panel-en-pin {
832 rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
833 };
834
835 lcd_panel_reset_pin: lcd-panel-reset-pin {
836 rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
837 };
838 };
839
840 leds {
841 pwr_led_pin: pwr-led-pin {
842 rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
843 };
844
845 slp_led_pin: slp-led-pin {
846 rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
847 };
848 };
849
850 pmic {
851 pmic_int_l_pin: pmic-int-l-pin {
852 rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>;
853 };
854
855 vsel1_pin: vsel1-pin {
856 rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
857 };
858
859 vsel2_pin: vsel2-pin {
860 rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
861 };
862 };
863
864 sdcard {
865 sdmmc0_pwr_h_pin: sdmmc0-pwr-h-pin {
866 rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
867 };
868
869 };
870
871 sdio-pwrseq {
872 wifi_enable_h_pin: wifi-enable-h-pin {
873 rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
874 };
875 };
876
877 usb-typec {
878 vcc5v0_typec0_en_pin: vcc5v0-typec0-en-pin {
879 rockchip,pins = <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
880 };
881 };
882
883 usb2 {
884 pwr_5v_pin: pwr-5v-pin {
885 rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
886 };
887
888 vcc5v0_host_en_pin: vcc5v0-host-en-pin {
889 rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
890 };
891 };
892
893 wireless-bluetooth {
894 bt_wake_pin: bt-wake-pin {
895 rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
896 };
897
898 bt_host_wake_pin: bt-host-wake-pin {
899 rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
900 };
901
902 bt_reset_pin: bt-reset-pin {
903 rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
904 };
905 };
906 };
907
908 &pmu_io_domains {
909 pmu1830-supply = <&vcc_3v0>;
910 status = "okay";
911 };
912
913 &pwm0 {
914 status = "okay";
915 };
916
917 &pwm2 {
918 status = "okay";
919 };
920
921 &saradc {
922 vref-supply = <&vcca1v8_s3>;
923 status = "okay";
924 };
925
926 &sdmmc {
927 bus-width = <4>;
928 cap-mmc-highspeed;
929 cap-sd-highspeed;
930 cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
931 disable-wp;
932 pinctrl-names = "default";
933 pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
934 sd-uhs-sdr50;
935 vmmc-supply = <&vcc3v0_sd>;
936 vqmmc-supply = <&vcc_sdio>;
937 status = "okay";
938 };
939
940 &sdio0 {
941 bus-width = <4>;
942 cap-sd-highspeed;
943 cap-sdio-irq;
944 keep-power-in-suspend;
945 mmc-pwrseq = <&sdio_pwrseq>;
946 non-removable;
947 pinctrl-names = "default";
948 pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
949 sd-uhs-sdr104;
950 status = "okay";
951 };
952
953 &sdhci {
954 bus-width = <8>;
955 mmc-hs200-1_8v;
956 non-removable;
957 status = "okay";
958 };
959
960 &spi1 {
961 max-freq = <10000000>;
962 status = "okay";
963
964 spiflash: flash@0 {
965 compatible = "jedec,spi-nor";
966 reg = <0>;
967 m25p,fast-read;
968 spi-max-frequency = <10000000>;
969 };
970 };
971
972 &tcphy0 {
973 status = "okay";
974 };
975
976 &tcphy0_dp {
977 port {
978 tcphy0_typec_dp: endpoint {
979 remote-endpoint = <&usbc_dp>;
980 };
981 };
982 };
983
984 &tcphy0_usb3 {
985 port {
986 tcphy0_typec_ss: endpoint {
987 remote-endpoint = <&usbc_ss>;
988 };
989 };
990 };
991
992 &tcphy1 {
993 status = "okay";
994 };
995
996 &tsadc {
997 /* tshut mode 0:CRU 1:GPIO */
998 rockchip,hw-tshut-mode = <1>;
999 /* tshut polarity 0:LOW 1:HIGH */
1000 rockchip,hw-tshut-polarity = <1>;
1001 status = "okay";
1002 };
1003
1004 &u2phy0 {
1005 status = "okay";
1006
1007 u2phy0_otg: otg-port {
1008 status = "okay";
1009 };
1010
1011 u2phy0_host: host-port {
1012 phy-supply = <&vcc5v0_otg>;
1013 status = "okay";
1014 };
1015
1016 port {
1017 u2phy0_typec_hs: endpoint {
1018 remote-endpoint = <&usbc_hs>;
1019 };
1020 };
1021 };
1022
1023 &u2phy1 {
1024 status = "okay";
1025
1026 u2phy1_otg: otg-port {
1027 status = "okay";
1028 };
1029
1030 u2phy1_host: host-port {
1031 phy-supply = <&vcc5v0_otg>;
1032 status = "okay";
1033 };
1034 };
1035
1036 &uart0 {
1037 pinctrl-names = "default";
1038 pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
1039 uart-has-rtscts;
1040 status = "okay";
1041
1042 bluetooth {
1043 compatible = "brcm,bcm4345c5";
1044 clocks = <&rk808 1>;
1045 clock-names = "lpo";
1046 device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
1047 host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
1048 max-speed = <1500000>;
1049 pinctrl-names = "default";
1050 pinctrl-0 = <&bt_host_wake_pin &bt_wake_pin &bt_reset_pin>;
1051 shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
1052 vbat-supply = <&wifi_bat>;
1053 vddio-supply = <&vcc_wl>;
1054 };
1055 };
1056
1057 &uart2 {
1058 status = "okay";
1059 };
1060
1061 &usb_host0_ehci {
1062 status = "okay";
1063 };
1064
1065 &usb_host0_ohci {
1066 status = "okay";
1067 };
1068
1069 &usb_host1_ehci {
1070 status = "okay";
1071 };
1072
1073 &usb_host1_ohci {
1074 status = "okay";
1075 };
1076
1077 &usbdrd3_0 {
1078 status = "okay";
1079 };
1080
1081 &usbdrd_dwc3_0 {
1082 dr_mode = "host";
1083 status = "okay";
1084 };
1085
1086 &usbdrd3_1 {
1087 status = "okay";
1088 };
1089
1090 &usbdrd_dwc3_1 {
1091 dr_mode = "host";
1092 status = "okay";
1093 };
1094
1095 &vopb {
1096 status = "okay";
1097 };
1098
1099 &vopb_mmu {
1100 status = "okay";
1101 };
1102
1103 &vopl {
1104 status = "okay";
1105 };
1106
1107 &vopl_mmu {
1108 status = "okay";
1109 };
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.