1 #
2 # This config is an example usage of ktest.pl with a kvm guest
3 #
4 # The guest is called 'Guest' and this would be something that
5 # could be run on the host to test a virtual machine target.
6
7 MACHINE = Guest
8
9
10 # Use virsh to read the serial console of the guest
11 CONSOLE = virsh console ${MACHINE}
12
13 # Use SIGKILL to terminate virsh console. We can't kill virsh console
14 # by the default signal, SIGINT.
15 CLOSE_CONSOLE_SIGNAL = KILL
16
17 #*************************************#
18 # This part is the same as test.conf #
19 #*************************************#
20
21 # The include files will set up the type of test to run. Just set TEST to
22 # which test you want to run.
23 #
24 # TESTS = patchcheck, randconfig, boot, test, config-bisect, bisect, min-config
25 #
26 # See the include/*.conf files that define these tests
27 #
28 TEST := patchcheck
29
30 # Some tests may have more than one test to run. Define MULTI := 1 to run
31 # the extra tests.
32 MULTI := 0
33
34 # In case you want to differentiate which type of system you are testing
35 BITS := 64
36
37 # REBOOT = none, error, fail, empty
38 # See include/defaults.conf
39 REBOOT := empty
40
41
42 # The defaults file will set up various settings that can be used by all
43 # machine configs.
44 INCLUDE include/defaults.conf
45
46
47 #*************************************#
48 # Now we are different from test.conf #
49 #*************************************#
50
51
52 # The example here assumes that Guest is running a Fedora release
53 # that uses dracut for its initfs. The POST_INSTALL will be executed
54 # after the install of the kernel and modules are complete.
55 #
56 POST_INSTALL = ${SSH} /sbin/dracut -f /boot/initramfs-test.img $KERNEL_VERSION
57
58 # Guests sometimes get stuck on reboot. We wait 3 seconds after running
59 # the reboot command and then do a full power-cycle of the guest.
60 # This forces the guest to restart.
61 #
62 POWERCYCLE_AFTER_REBOOT = 3
63
64 # We do the same after the halt command, but this time we wait 20 seconds.
65 POWEROFF_AFTER_HALT = 20
66
67
68 # As the defaults.conf file has a POWER_CYCLE option already defined,
69 # and options can not be defined in the same section more than once
70 # (all DEFAULTS sections are considered the same). We use the
71 # DEFAULTS OVERRIDE to tell ktest.pl to ignore the previous defined
72 # options, for the options set in the OVERRIDE section.
73 #
74 DEFAULTS OVERRIDE
75
76 # Instead of using the default POWER_CYCLE option defined in
77 # defaults.conf, we use virsh to cycle it. To do so, we destroy
78 # the guest, wait 5 seconds, and then start it up again.
79 # Crude, but effective.
80 #
81 POWER_CYCLE = virsh destroy ${MACHINE}; sleep 5; virsh start ${MACHINE}
82
83
84 DEFAULTS
85
86 # The following files each handle a different test case.
87 # Having them included allows you to set up more than one machine and share
88 # the same tests.
89 INCLUDE include/patchcheck.conf
90 INCLUDE include/tests.conf
91 INCLUDE include/bisect.conf
92 INCLUDE include/min-config.conf
93 INCLUDE include/bootconfig.conf
Linux® is a registered trademark of Linus Torvalds in the United States and other countries.
TOMOYO® is a registered trademark of NTT DATA CORPORATION.